Indiazone Enterprises

Dahisar, Mumbai, Maharashtra

EMPL’s SIEVE HD dialyzers have Polypropylene (PP) Series and Polycarbonate (PC) Series.SIEVE HD Series has an excellent clearance rate that offers high efficiency & complete spectrum solutions that facilitate filter of all types of molecules in dialysis treatment with better safety.SIEVE HD Series has excellent biocompatibility that offers high quality life of patient’s life. It has the ability of constant toxins clearance rate that filtrate middle & large molecules.SIEVE HD Series Dialyzer has lower albumin loss during procedure. It offers high β2-microglobulin clearance with efficacy & safety.SIEVE HD Series is BPA Free Hemodialyzers.

SIEVE HD Series High flux dialyzers are made up of cellulose permeable membranes with a higher permeability. It clears the toxins with medium and high molecular weights, such as β2-microglobulin, and phosphorus that accumulate during CKD.SIEVE HD Series high flux dialyzers also absorb toxins associated with uremia and remove cytokines and complement activators because of their hydrophobic properties that diminish inflammatory responses.

• Medtronic Bio-Medicus Bioconsole
• Centrifugal Extracorporeal Blood Pump
• Model: 550
• Serial No: 7530
• 120 VAC – 60 Hz – 3A
• Controls: Pump Speed, 2 Timers, Alarm Limits, Pressure zero, Volume
• Switches: Master Power, Display Test, Motor Transfer, AC/28V/Battery, Battery Test/Standby
• Displays: Pump Speed, Flow, Pressure, Battery, 2 Timers
• Hospital grade cord
• Red protective pump cap

These cannulas feature flanged, radiopaque basket tips. All cannulas have female luer connection site.

AV Fistula needles are a crucial link between the patient and the dialysis machine. AVF Arteriovenous Fistula Needle offers high performance & thin needle surface with & without back eye. The inner diameter & length are the key factors that affect the extracorporeal flow rate & increases efficacy of the hemodialysis procedure. Higher blood flow is directly proportional to the larger inner diameter & shorter tube length. AVF Arteriovenous fistula needle has bevelled cutting edge and polished to offer sharp tip. The rounded trailing edge provides optimal conditions for the cutting and stretching of the tissue that helps the surgeon during procedure.

AVF fistula needles are equipped with a colour-coded wing that specifies the outer diameter of the cannula.

The Maquet Datascope CS300 IABP with IntelliSense combines fiber-optic speed with automatic in vivo calibration. The result is a faster time for therapy, faster signal acquisition, and faster adaptation to rate and rhythm changes. Maquet has the only fiber-optic IABP and catheter system that automatically calibrates in the patient after insertion and automatically recalibrates in vivo every two hours or sooner should the patient or environmental conditions change.

The CS300 Datascope IABP with IntelliSense software is designed to emulate an experienced user, allowing you more time to focus on your patient. This sophisticated algorithm automatically selects the best lead and trigger source, sets optimal inflation and deflation timing, and still allows the clinician theability to fine-tune deflation timing. The Maquet IABP quickly adapts to rate or rhythm changes in order to optimize augmentation and support during diastole. Another version of the Maquet Datascope Intra-Aortic Balloon Pump is the Maquet Datascope CS 100

• Faster inflation and deflation speed
• CS300 has true one-button start-up
• Automatically calibrates the fiber-optic pressure sensor in the patient and recalibrates every 2 hours or sooner should patient or environmental conditions change
• Automatically evaluates and selects the best lead and trigger source
• Automatically sets optimal timing
• Automatically adjusts to changes in patient conditions without clinician intervention
• A Maquet fiber-optic IAB catheter
• Conventional fluid-filled IAB catheters

• Size on Cart: 43.1” H x 22.3” D x 16.8” W (109 cm H x 56.6 cm D x 42.7 cm W)
• Size off Cart: 26.9” H x 20.5” D x 10.8” W (68.3 cm H x 52.1 cm D x 27.4 cm W)
• Console Weight: 84.8 lbs. (38.4 Kg) nominal (includes S.D., CRM, and He tank)
• Monitor: 9.5 lbs. (4.3 Kg) nominal
• Hospital Cart Weight: 52.4 lbs. (23.8 Kg) nominal
• Internal Battery: 34 lbs. (15.4 Kg) nominal
• Storage Bag: 4.6 lbs. (2.1 Kg) nominal (includes doppler and doppler holder))

• Color TFT Liquid Crystal Display (LCD) 8.3”(21cm)W x 6.2”(15.8cm)H; up 45°, 10.4” diagonal (26.4 cm) down 55°, right 70°, left 70° viewing angle; Rotates 330°; Tilts 180°; Detachable; Laptop-like closure for storage and protection; Remote monitor mount (optional)

• ECG Trigger: Threshold dynamically adjusted by the system for high sensitivity and selectivity of the R-wave detection; Minimum = 120µV ± 20µV at a normal gain; 40µV at max. gain
• Pressure Trigger: The default trigger threshold is automatically adjusted to 38% of the systolic pulse height; 7 mm minimum
• Manual threshold mode: User-adjustable between 7 and 30 mmHg ± 3 mmHg
• Pacer A Trigger: R-wave detection (as above) except pacer blanking is extended to 100 ms
• Pacer V/A-V Trigger: V Pacer: fixed at a rate up to 185 bpm (no demand pacing)
• A-V Pacer: fixed at a rate up to 125 bpm (no demand pacing) with A-V intervals between 80-224 ms

• Mains Voltage: 100-120 VAC ± 10% or 220-240 VAC ± 10%
• Mains Frequency: 50/60 Hz ± 3 Hz
• Internal Battery: 24 VDC (nominal), 17.2 Amp-hour, approx. 3 hrs. @ 90 bpm
• Battery Type: Maintenance-free; Sealed lead-acid

• Pressure Output: (electrically isolated)
• Pressure Range: 0 to +300 mmHg (minimum)

• Op. Temp.: 10°C – 40°C
• Op. Humidity: 5 – 95% (R.H.) non-condensing
• Op. Altitude: 0 – 12, 000 feet (3, 657 m); automatic altitude correction for IAB pressure

• ECG Leads: In Auto Operation Mode: I, II, III, External In Semi-Auto Mode: I, II, III, AVR, AVL, AVF, V, External (12 lead compatibility)
• ECG Gain (default): 1 V output per 1 mV input ±5% (waveform automatically scaled to occupy ECG display window)
• Gain (variable): 0.15 to 3.0 cm/mV ±20% (autoscaling disabled)
• Frequency Response: 0.5-12 Hz (display); 0.5-135 Hz (Output to External Monitor)
• Defibrillator Protection: Discharge level = 360 J (trace returns to the screen in 5-sec max)
• ESIS: Automatic suppression with internal ECG amplifier

The Terumo Sarns11160 Dual Heater-Cooler is a reliable, efficient patient cooling/heating system. Refurbished units are available. Please contact us for pricing information.

• Simple controls and high reliability
• Large capacity heater with four temperature settings
• Independent water supply and recirculating system

The Medtronic Bio-Console 560 Speed Controller offers control and monitoring for the BPX-80 & Affinity CP Centrifugal Blood Pumps. The ergonomic design of the Bio-Console Pump features an uncluttered control panel and highly visible graphics. This Centrifugal pump is compatible with most heart-lung consoles. The special RPM control knob alerts the operator that a low-flow condition is approaching. The total system includes the Bio-Console 560 pump speed controller with LED Touch Display, TX50 Adult Flow Transducer, and 540T External Drive Motor with adjustable arm assembly.

Are you looking for a full ECMO Machine setup? Click here!

• Color-coded status displays text messages
• Three timers with countdown or elapsed time.
• Two independently controlled level sensors communicate with the pump controller
• Flow display includes cardiac index flow target calculation
• User-selectable pump stop/coast responses
• Arterial line auto-clamp system helps prevent backflow
• Updated electronic architecture provides additional functional enhancements.
• Utilizes remote pump drive for optimum placement

• Bio-Cal 370 Temperature Control Module.
• Model 150 Emergency Handcrank.
• Sechrist Air Oxygen Mixer.
• Medtronic ACT Plus Automated Coagulation Timer System.
• Portable Bypass System (PBS) Cart/cabinet.

• Overall Size: 22.18 cm (8.7 in) wide by 34.5 cm (13.6 in) long
• Screen Size: 26.41 cm (10.4 in) diagonal
• Weight: 4.26 kg (9.4 lb)

• Size: 31.88 cm (12.55 in) high by 22.83 cm (8.99 in) wide by 43.02 cm (16.9 in) long</.li>
• Weight: 17.19 kg (37.9 lb)

• 100 VAC, 50-60 Hz, 3 amps
• 110-120 VAC, 50-60 Hz, 3 amps
• 220-240 VAC, 50-60 Hz, 1.5 amps

• Brushless DC (non-arcing)

• Type: Two, series connected, 12 VDC lead-acid gel; rechargeable
• Discharge Time: Refer to Appendix C in the product manual: Battery Longevity
• Recharge Time: 18 hours to 90% capacity; 24 hours to 100% capacity

• Flow: -9.99 to +9.99 L/min +/- (5% + 50 mL)
• RPM: 0 to 4500 RPM
• Pressure: -300 to +999 mm Hg +/- (5% + 5 mm Hg)

• Temperature: +18° to +33°C, +64° to +92°F
• Humidity: 10% – 95%, non-condensing

• Temperature: -40° to +66°C, -40° to +150°F
• Humidity: 10% – 95%, non-condensing

• Digital: RS 232 Interface: flow, RPM, pressure, alarm status
• Baud Rate: 1200 to 19200

The LivaNova Sorin Stockert 3T is a heater-cooler that is used during cardiopulmonary bypass. The System is used to help regulate the patient’s blood during cardiac, vascular, and transplant procedures. The Stockert 3T system can work independently from the water supply in an operating room. It comes with three different water tanks that control the warming and cooling cardioplegias along with the patient’s temperature. Each one of these is on its own separate circuit and can be run simultaneously. The Sorin Stockert heating and cooling of the system runs off of one circuit while the patient temperature runs off of two circuits. The water in the LivaNova 3T does not come in contact with the patient’s or the patient’s blood during a procedure.

At the end of a procedure, the water can be drained out of the heat exchange, and the tubing to help with clean up.

• Short pre-cooling time
• 2 Small volume tanks for warming and Cooling
• Independent safety system to prevent the water temperature from reaching critical temperatures
• Two-chamber pumps to minimize the pressure inside the heating chamber
• The Suction of the pumps allows for a smooth emptying of the heating chamber and the tubing

The MAQUET HCU 30 heater/cooler system is used to circulate water through heat exchange circuits to warm or cool a patient during cardiopulmonary bypass procedures that last 6 hours or less. The HCU 30 heater/cooler unit supplies temperature-controlled water for heat exchangers or hyper-hypothermia blankets. The temperature of the water can be adjusted from 1°C to 40.5°C. This MAQUET heater/cooler unit 30 features a 26-liter tank. An Internal safety system on the HCU 30 monitors the regulation to prevent the water from rising above 41.3°C.

• High cooling capacity with its fast ice-building technique and powerful compressor.
• A large capacity heater that incorporates precise electronic control.
• Fast priming and automatic de-airing.

• Size: (H x W x D) 106 x 46.5 x 52.5 cm
• Weight Approx.: 95 kg empty, 121 kg full
• Noise level (normal operation): 38 Lpa dB

• Control range: 1°C to 40, 5°C
• Setting resolution: 0.1°C
• Temperature measurement accuracy: ±0.3°C
• Temperatures display range: 0°C to 99°C

• Tank volume: 26 litres
• Initial cooling capacity: (relative 20°C) 6250 kJ
• Continuous cooling capacity: 4270 kJ/h (1186 W)

• Capacity: (max. values) 3100 W (230 V), 1800 W (115 V), 1500 W (100 V)

• Flow capacity, main circuit: Approx. 21.0 l/min at zero head (adjust-able)
• Flow capacity, cardioplegia circuit: Approx. 7.0 l/min at zero head
• Maximum pressure, main circuit: Approx. 2.4 bar (adjustable)
• Maximum pressure, cardioplegia circuit: Approx. 0.9 bar

• Mains: 200-240 V/50 Hz, 220 V/60 Hz, 100-120 V / 60 Hz, 100 V/50 Hz/li>
• Mains fuse: 16 A (230 V)
• Power consumption: 3680 W (230 V)

The Datascope SC 100 is an intra-aortic balloon pump that features Intellasync software. The Maquet Datascope CS100 and the Datascope Cs 100 are the same base system the only difference between them is the software on each unit. The CS100 has the more recently updated software. The Datascope IAPB can be used in an operating room, catheter lab, or critical care setting. The system offers three operation modes; automatic, semi-automatic, and manual, making it easy to switch between modes when needed. The Datascope CS100 offers a foldable and detachable laptop-style display. The color display screen makes it easier for caregivers to adjust the pump and monitor the patient remotely. Another version of the Maquet Datascope Intra-Aortic Balloon Pump is the Maquet Datascope CS 300.

• Maquet CS100 IABP comes with Intellisync and offers a one-button start-up, automatically adapting to changing conditions, making it the right choice for any patient’s condition.
• Automatically evaluates and selects optimal trigger source and lead
• Sets inflation at the dicrotic notch and deflates IAB at the start of systole
• Responds to changes in signal quality by selecting a new trigger source Automated trigger source and timing management to provide continuous, consistent support for your patient.
• Fast, one-button start-up automatically conducts autofill and initiates 1:1 assist.
• Full color, high contrast display tilts for easy viewing.<//li>
• Display and keypad in laptop-style configuration, allowing caregivers to fold and detach the unit for remote operation.Easy-to-use keypad with an intuitive user interface.
• Customizable display panel allows operators to adjust sweep speed, brightness, balloon waveform, and inflation markers.
• Switch easily between three operation modes: Automatic, Semi-Automatic, and Manual.
• Automatically evaluates and selects optimal trigger source and lead.
• The system detects changes and easily adapts to new patient rhythms.
• Fully annotated printouts with user-configurable waveforms and strip lengths.
• Locking casters and durable design keep the CS100 secure in a variety of settings.

• Height: 30 in (76.2 cm)
• Width: 22.5 in (57.2 cm)
• Depth: 13.2 in (33.5 cm)
• On Cart
  • Height: 42.2 in (114.8 cm)
  • Width: 17.6 in (44.7 cm)
  • Depth: 23.4 in ( 59.4 cm)
• Off Cart
  • Height: 28.2 in (71.6 cm)
  • Width: 11.3 in (28.7 cm)
  • Depth: 21.5 in ( 54.6 cm)
• Monitor weight: 9.5 lb (4.3 kg)
• Console weight: 133.2 lb ( 60.4 kg)

• Width:8.3 in (21cm)
• Height: 6.2 in (15.8 cm)
• viewing angle:
  • Up: 45°
  • Down 55°
  • Right 70°
  • Left 70°
  • Rotates 330°<?li>
  • Tilts180°
• Detachable Laptop-like closure for storage and protection

• Mains Voltage: 100-120 VAC ± 10% or 220-240 VAC ± 10%
• Mains Frequency: 50/60 Hz ± 3 Hz
• Internal Battery: 24 VDC (nominal), 17.2 Amp-hour, 3 hrs.(approx. @ 90 bpm)
• Battery Type: Maintenance-free; Sealed lead-acid

• ECG Gain (default): 1 V output per 1 mV input ±5% (waveform automatically scaled to occupy ECG display window)
• Gain (variable): 0.15 to 3.0 cm/mV ±20% (autoscaling disabled)
• Frequency Response: 0.5-12 Hz (display); 0.5-135 Hz (Output to Monitor)
• Defibrillator Protection: Discharge levels 360 J (trace returns to the screen in 5 sec. max)

• Operating Temperature: 10°C – 40°C
• Operating Humidity: 5 – 95% (R.H.) non-condensing
• Operating Altitude: 0 – 12, 000 feet (3, 657 m); automatic altitude correction for IAB pressure

• ECG Trigger: Threshold dynamically adjusted by a system for high sensitivity and selectivity of the R-wave detection; Minimum = 120µV ± 20µV at normal gain; 40µV at max. gain
• Pressure Trigger: The default trigger threshold is automatically adjusted to 38% of the difference between peak systolic and end-diastolic (avg. over multiple cycles); In variable mode: User-adjustable between 7 and 30 mmHg ± 3 mmHg
• Pacer A Trigger: R-wave detection (as above) except pacer blanking is extended to 100 ms
• Pacer V/A-V Trigger: V Pacer: fixed at a rate up to 185 bpm (no demand pacing) A-V Pacer: fixed at a rate up to 125 bpm (no demand pacing) with A-V intervals between 80-224 ms
• Internal Trigger: Variable mode: 40-120 bpm; Normal mode: 80 ± 1 bpm
• Tall T-Wave Rejection: Rejects all T-Waves where the Q-T interval is <300 ms and the amplitude is <70% of the QRS input amplitude
• Pacer Rejection: Rejects all pulses of amplitude ± 2.0 mV to ± 700 mV and durations between 0.1 ms to 2.0 ms with 1) No tail; 2) 100 ms time constant tail < 1 mV; 3) 25 ms time constant tail < 1 mV; 4) 4 ms time constant tail < 2 mV