Our Products
Pipe Tees
2 Products availableSteel Pipes
2 Products availableMetal Sheets
2 Products availableSteel Coils
1 Products availableStainless Steel Sheet
1 Products availableSteel Bars
1 Products availableDuplex 2205 is a nitrogen enhanced duplex stainless steel that was developed to combat common corrosion problems encountered with the 300 series stainless steels. Duplex describes a family of stainless steels that are neither fully austenitic, like 304 stainless, nor purely ferritic, like 430 stainless. The structure of 2205 duplex stainless steel consists of austenite pools surrounded by a continuous ferrite phase. In the annealed condition, 2205 contains approximately 40-50% ferrite. Often referred to as the work horse grade, 2205 is the most widely used grade in the duplex family of stainless steels. The advantage of a duplex structure is that it combines the favorable qualities of a ferritic alloy (stress corrosion cracking resistance and high strength) with those of an austenitic alloy (ease of fabrication and corrosion resistance). Usage of 2205 Duplex stainless steel should be limited to temperatures below 600 F. Extended elevated temperature exposure can embrittle 2205 stainless.
Forms of Duplex 2205
Sheet, Plate, Bar, Pipe & Tube (welded & seamless), Fittings (i.e. flanges, slip-ons, blinds, weld-necks, lapjoints, long welding necks, socket welds, elbows, tees, stub-ends, returns, caps, crosses, reducers, and pipe nipples), Welding Wire and Welding Electrode
. Corrosion Resistance
2205 duplex stainless steel is a cost effective solution for many applications where the 300 series stainless steels are susceptible to chloride stress corrosion cracking. Stress corrosion cracking occurs when stainless steels are subjected to tensile stress, while in contact with solutions containing chlorides. Increasing temperatures also increase the susceptibility of stainless steels to stress corrosion cracking. The combination of chromium, molybdenum and nitrogen convey the good resistance of 2205 to chloride pitting and crevice corrosion. This resistance is extremely important for services such as marine environments, brackish water, bleaching operations, closed loop water systems and some food processing applications. The high chromium, molybdenum and nitrogen contents of 2205 provide corrosion resistance superior to common stainless steels, such as, 316L and 317L in most environments.
Applications for Duplex 2205
Alloy Designation | UNS | BS | EN | Basic | DIN | JIS | Trade Name | ASTM |
Alloy 2205 | S31803 | 1.4462 | 22Cr-5Ni-3Mo-0.15N | X2CrNiMoN22-5-3 | SUS329L3L (JIS G3463) | SAF 2205 22Cr | ||
Alloy 2205 | S32205 | 1.4462 | 22.5Cr-6Ni-3Mo-0.2N | SAF 2205 22Cr | A789 |
Inconel is a nickel-chromium alloy used for applications that require corrosion and high temperature resistance. This nickel alloy was designed for service temperatures from cryogenic to elevated temperatures in the range of 2000 F. It is non-magnetic, has excellent mechanical properties, and presents the desirable combination of high strength and good weldability under a wide range of temperatures.
We make available Stainless Steel HR & CR Coils of superior quality to the clients. The Stainless Steel HR & CR Coils that we offer are of superior quality. These Stainless Steel HR & CR Coils that we offer possess optimum quality, sturdy composition, excellent finish, and durability. Clients can avail the Stainless Steel HR & CR Coils from our company in proper packaging, that too at affordable rates in the market.
Specification DIN/EN/ ASTM
Available In Width 100mm to 2000mm Max. Coil weight 1 to 20 Ton. Minimum & Maximum Thickness Cold Rolled Coil: 0.30m to 3.00 mm.Hot Rolled Coil: 3.00mm To 80.00mm.
Grades | Range |
200 Series | 201, 202 |
300 Series | 301, 304, 304L, 304H, 304N, 304LN, 309S, 316, 316H, 316L, 316TI, 316LN, 317, 317L, 310, 310S, 321H, 347, 347H , 904L |
400 Series | 409, 410, 420, 430 |
Our organization is involved in manufacturing, exporting, trading and supplying a extensive range of Stainless Steel Plates to our clients. Used in various industrial applications, these plates are manufactured by the experienced professionals from high-quality raw material and advanced technology.
Specification:-
Grades Stainless Steel 202, 303, 304, 304L, 309, 310, 316, 316L, 316TI, 317, 317L, 321, 410, 416, 420, 430, 440C, 904L
Range 5 mm to 100 mm thick in 1000 mm to2500 mm width & 2500 mm to 12500 mm length available with NACE MR 01-75s
TypesSheet, Coils, Flat, Profile, Blank, Circle, Ring, Plates, Strips
FinishingNo.1, 2B, BA, mirror polishing, 2D, No.4, 8K
Thickness0.31-100 mm
We are a leading name, which is engaged in offering a comprehensive range of Stainless Steel Rods, Bars & Wire. The offered range is manufactured utilizing superior grade raw material such as stainless steel and allied, procured from reliable vendors of the market. In addition to this, the offered range is tested on different parameters to ensure its tandem with the highest quality norms and standards.
Specification:- Grades Stainless Steel 202, 303, 304, 304L, 309, 310, 316, 316L, 316TI, 317, 317L, 321, 410, 416, 420, 430, 440C, 904L Diameter 6.0-400 mm StandarsGB, JIS, DIN, ASTM
Our Stainless Steel Flanges are of one of the best quality. We also have an exclusive range of stainless steel flanges which is of high exclusive quality. Stainless Steel Flanges available in a spectrum of shape and sizes, our forged light weight weld flanges are manufactured using superior grade material such as stainless steel.
Specification Grade Stainless Steel 202, 303, 304, 304L, 309, 310, 316, 316L, 316TI, 317, 317L, 321, 410, 416, 420, 430, 440C, 904L Range (15 NB) to 48 (1200NB) in 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS, ASA 150, ASA 300 Types Socket Weld, Slip On, Blind, Lapped, Screwed, Weld Neck, Long Weld Neck, Reducing, Spectacle, Ring Joint FeacturesDimensional accuracyHigh strengthDurabilityCorrosion resistanceExcellent finish
We are offering a premium range of Stainless Steel Fasteners. These Stainless Steel Fasteners are made from very high quality raw material which ensures hassle free work performance at its user end. The provided pipes are well known for being in-line with internationally laid quality parameters as they are constructed from world class raw material. We let our range of products to go through a quality test before procurement so that their quality may be properly checked.
Specification Grade Stainless Steel 202, 303, 304, 304L, 309, 310, 316, 316L, 316TI, 317, 317L, 321, 410, 416, 420, 430, 440C, 904L Size M10 to M36
Types Bolts Stud Bolts, Hex Head Bolts, Socket Hexagon Head Screw Anchor Bolts, U-Bolts, J Bolts, Mushroom Head Square Neck Bolts , T- Head Bolts , Wing Screw , Eye Bolt , Eye Bolt, Foundation Bolts, Structural Bolts. ApplicationStainless steel fasteners can be used in racing industries such as racing motorcycles and cars, sailing boats and medical equipment, etc.
Stainless Steel Buttweld Fitting accomplish a lot of admiration by our clients owing to its high strength, dimensional correctness, high tension power, corrosion resistant and consistency. These products are used in various commercial, industrial and automobile industries. We manufacture these fittings using high grade of raw material by implementing most ultra modern technology. These products are clients can avail from us at various sizes, shapes and design as per the requirements.
Specification Grade Stainless Steel 202, 303, 304, 304L, 309, 310, 316, 316L, 316TI, 317, 317L, 321, 410, 416, 420, 430, 440C, 904L Size 15 NB To 300 NB
Types Bend (Long & Short)Elbow (180 Deg., 90 Deg. & 45 Deg.)Tee (Equal & Unequal)Reducer (Concentric & Eccentric)CAP, Stub end (Long &Short)Nipple (Barrel) ApplicationPetrochemicals PlantsChemical PlantsIndustrial Machinery Power IndustryGovernment Companies
Alloy Steel Pipes & Tubes are extensively used for conveyance of fluids intended for critical high temperature and general corrosion service applications.
Alloy Steel Pipes & Tubes are used in under similar service conditions in heat transfer process equipments like Boilers, Super Heaters, Heat Exchangers, Condensers etc. General Engineering and Process Instrumentation.
Specification:- Grades Gr P 1 , P 5 , P 9 , P 11 , P 12 , P 22 , P 23 , P 91 Ange" NB TO 24 NB IN SCH 20 , 30, STD, 40 , 60 , 80 , XS , 100 , 120 , 140 , 160 & XXS as Per NACE MR 01 75 Type SEAMLESS / FABRICATED LengthSingle Random, Double Random & Cut Length EndPlain End, Bevelled End, Threaded Standard ASTM / ASME A 335 The salient features are as follows :Excellent mechanical & magnetic propertiesHigh thermal & electrical conductivityLow gas content & vapor- pressure
We are reputed manufacturers and exporters of high quality Sheets & Plates. These products are globally known for its compliance with the industry set norms. We offer them in various grades that meet the requirements of the client. Our range comprises of Stainless Steel Sheets & Plates.
Specification:- Grades F 5, F 9, F 11, F 12, F 22, F 91. High Speed Steel (HSS), HCHCR & OHNS in Grade M2, M3, M35, M42, T-1, T-4, T-15, T-42, D2, D3, H11, H13, OHNS-01 & EN52. EN Series in Grade EN-1A, EN-3B, EN-8, EN-9, EN-16, EN-18, EN-19, EN-24, EN-29B, EN-31, EN-32B, EN-36, EN-36C, EN-42J, EN-45, EN-47, EN-48A, EN-100, EN-111, EN-202, EN-352, EN-353, EN-1117 Etc. Standard ASTM / ASME A/SA 387 Range 5 mm To 200 mm thick in 1000 mm TO 2500 mm width & 2500 mm to 12500 mm Length Sheets & Plates In Form Of Sheet, Plates, Flat, Strips, Profile, Blank , Circle, Ring etc.
Highly appreciated for its durability, sturdy construction and tear-resistance, our range of Carbon & Alloy bars & Wires is quality tested at ours and the vendors' premises. We also offer these in different alloy grades, which is mentioned below:
Specification:- Grades F 5, F 9, F 11, F 12, F 22, F 91. Ranges 20 mm To 300 mm Dia in 100 mm TO 6000 mm Length High Speed Steel (HSS), HCHCR & OHNS in GradeM2, M3, M35, M42, T-1, T-4, T-15, T-42, D2, D3, H11, H13, OHNS-01 & EN52. EN Series in GradeEN-1A, EN-3B, EN-8, EN-9, EN-16, EN-18, EN-19, EN-24, EN-29B, EN-31, EN-32B, EN-36, EN-36C, EN-42J, EN-45, EN-47, EN-48A, EN-100, EN-111, EN-202, EN-352, EN-353, EN-1117 Etc. FormRound FinishBright, Black Standard ASTM / ASME A/SA 182
Titanium and titanium alloys are attractive structural materials due to their high strength, low density, and excellent corrosion resistance. However, even though titanium is the fourth most abundant element in the Earths crust, the cost of titanium is high due to its high melting point and extreme reactivity. The high cost includes both the mill operations (extraction, ingot melting, and primary working) as well as many of the secondary operations conducted by the user. The advantages of titanium include:
Properties:- Titanium alloys are known for their combination of relatively low densities, high strengths, and excellent corrosion resistance. Yield strengths vary from 480 MPa (70 ksi) for some grades of commercial titanium to approximately 1100 MPa (160 ksi) for structural alloys. In addition to their static strength advantage, titanium alloys have much better fatigue strength than the other lightweight alloys, such as those of aluminum and magnesium. Titanium alloys can be used at moderately elevated temperatures, as high as 370 to 595 C (700 to 1100 F) depending on the specific alloy. In addition, some alpha-titanium alloys, especially the low interstitial grades, can also be used in cryogenic applications because they do not exhibit a ductile-to-brittle transition.
An important property of titanium alloys is corrosion resistance. When exposed to air, titanium immediately forms an oxide layer a few nanometers thick that protects the underlying metal from further oxidation. If this oxide layer is damaged, it re-forms in the presence of even trace amounts of oxygen or water. The oxide is strongly adherent and stable over a wide pH range of corrosive solutions as long as moisture and oxygen are present to maintain the protective oxide layer.
Thermal and Electrical Properties:-Titanium and its alloys have very low thermal conductivities and high electrical resistivities
Mechanical Properties:-Commercially pure grades of titanium have an ultimate tensile strength of approximately 410 MPa (60 ksi), equal to that of common low-alloy steels, but are 45% lighter. Although titanium is approximately 60% more dense than aluminum, it is about twice as strong as common aluminum structural alloys. Certain alloys can be heat treated to achieve tensile strengths as high as 1400 MPa (200 ksi).
Applications :- As a result of their high strength-to-density, good corrosion resistance, resistance to fatigue and crack growth, and their ability to withstand moderately high temperatures without creep, titanium alloys are used extensively in aerospace for both airframe and engine components. In aircraft, titanium alloys are used for highly loaded structural components such as bulkheads and landing gears. In commercial passenger aircraft engines, the fan, the low-pressure compressor, and approximately of the high-pressure compressor are made from titanium alloys. Other important applications include firewalls, exhaust ducts, hydraulic tubing, and armor plating. Due to its high cost, titanium alloys are more widely used in military aircraft than commercial aircraft. For example, titanium alloys comprise approximately 42% of the structural weight of the new F-22 fighter aircraft, while the Boeing 757 contains only 5% Ti.
The excellent corrosion resistance of titanium makes it a valuable metal in the chemical processing and petroleum industries. Typical applications include pipe, reaction vessels, heat exchangers (Fig. 4), filters, and valves. Titanium is used in the pulp and paper industries, where it is exposed to corrosive sodium hypochlorite or wet chlorine gases. Due to excellent resistance to saltwater, titanium is used for ship propeller shafts and service water systems. The former Soviet Union actually developed large, welded titanium-hulled submarines.
A growing use of titanium is in medical applications. Titanium is biocompatible with the human body (nontoxic and not rejected by the body). It is used for surgical implements and implants such as hip balls and sockets and heart valves. The lower elastic modulus of titanium more closely matches the properties of human bone than do stainless steel alloys, which results in less bone degradation over long periods of time. Titanium is also used for dental implants to replace missing teeth.
Titanium is used in many sporting goods, including golf club heads, tennis rackets, bicycle frames, skis, scuba gas cylinders, and lacrosse sticks. Approximately 95% of titanium ore is refined into titanium dioxide (TiO2) and used as white fade-resistant pigment in paints, paper, toothpaste, and plastics.
Grade 1 Unalloyed titanium, low oxygen. Grade 2 Unalloyed titanium, standard oxygen. Grade 2H Unalloyed titanium (Grade 2 with 58 ksi minimum UTS). Grade 3 Unalloyed titanium, medium oxygen. Grades 1-4 are unalloyed and considered commercially pure or "CP". Generally the tensile and yield strength goes up with grade number for these "pure" grades. The difference in their physical properties is primarily due to the quantity of interstitial elements. They are used for corrosion resistance applications where cost, ease of fabrication, and welding are important. Grade 5, also known as Ti6Al4V, Ti-6Al-4V or Ti 6-4, is the most commonly used alloy. It has a chemical composition of 6% aluminium, 4% vanadium, 0.25% (maximum) iron, 0.2% (maximum) oxygen, and the remainder titanium. It is significantly stronger than commercially pure titanium while having the same stiffness and thermal properties (excluding thermal conductivity, which is about 60% lower in Grade 5 Ti than in CP Ti). Among its many advantages, it is heat treatable. This grade is an excellent combination of strength, corrosion resistance, weld and fabricability. Generally, Ti-6Al-4V is used in applications up to 400 degrees Celsius. It has a density of roughly 4420 kg/m3, Young's modulus of 110 GPa, and tensile strength of 1000 MPa. By comparison, annealed type 316 stainless steel has a density of 8000 kg/m3, modulus of 193 GPa, and tensile strength of only 570 MPa. And tempered 6061 aluminium alloy has 2700 kg/m3, 69 GPa, and 310 MPa, respectively.
Designation |
UNS | DIN | AMS | Military | MIL-T | China | Russia | BSI | Specifications | Afnor |
Grade 1 | R50250 | 3.7025 | T-81556, T-81915 |
CP4 | TAD | BT1-00 | TA1 | ASTM B 265, 337, 338, 348; ASTM F 67 | T-35 | |
Grade 2 | R50400 | 3.7035 | 4902, 4941, 4942, 4951 | T-9046 CP-3, T-81556 |
CP3 | TA1 | BT1-0 | TA2, 3, 4, 5 | ASTM F 67; B 337, 338, 348, ISO 5832-2. | T-40 |
Grade 3 | R50550 | 3.7055 | 4900 | T-9046 CP-2, T-81556 |
CP2 | TA2 | OT4-0 | ASTM F 67; ASTM B 265, 337, 338, 348. | T-50 | |
Grade 4 | R50700 | 3.7065 | 4901 | T-9046 CP-1, T-9047 CP-70, F-83142 |
CP1, CP-70 |
TA3 | OT4-1 | TA 6,7,8,9 | ASTM F 67; ASTM B 265, 337, 338, 348, 381 | |
Grade 5 | R56400 | 3.7165 | 4905, 4906, 4911, 4920, 4928, 4930, 4931, 4934, 4935, 4954, 4965, 4967, 4993 | T-9046 AB1/2, T-9047, T-81556, T-81915, F-83142 |
AB1/2 | TA4 | OT4 | TA10, 11, 12, TA28, 56, 59 |
B 265, B 348, B 367 Grade C-5, B 381 Grade F-5 | |
Grade 6 | R54520 | TA5 | BT5 | |||||||
Grade 7 | R52400 | TA6 | BT5-1 | ASTM B 265, B 337, B 338, B 348,B 381. ASTM F 467, F 468. | ||||||
Grade 9 | R56320 | T-A3V2.5 | ||||||||
Grade 10 | TA8 | BT6c | ||||||||
Grade 11 | R52250 | TC1 | BT3-1 | |||||||
Grade 12 | R53400 | TC2 | BT9 | ASTM B 265, B 337, B 338, B 348,B 381. | ||||||
Grade 16 | R52402 | |||||||||
Grade 17 | R52252 | |||||||||
Grade 18 | R56322 | |||||||||
Garde 23 | R56401 | |||||||||
Grade 26 | R52404 | |||||||||
Grade 28 | R52254 |
We Supply Titanium Pipes, Tubes, Sheets, Plates, Coil Strip as per the following standards. We can also supply other than this standards. So do send us your enquiry.
ASTM B363 WPT1 | ASTM B363 WPT2 | ASTM B363 WPT2H | ASTM B363 WPT3 |
ASTM B363 WPT7 | ASTM B363 WPT7H | ASTM B363 WPT9 | ASTM B363 WPT11 |
ASTM B363 WPT12 | ASTM B363 WPT13 | ASTM B363 WPT14 | ASTM B363 WPT15 |
ASTM B363 WPT16 | ASTM B363 WPT16H | ASTM B363 WPT17 | ASTM B363 WPT18 |
ASTM B363 WPT19 | ASTM B363 WPT20 | ASTM B363 WPT21 | ASTM B363 WPT23 |
ASTM B363 WPT24 | ASTM B363 WPT25 | ASTM B363 WPT26 | ASTM B363 WPT26H |
ASTM B363 WPT27 | ASTM B363 WPT28 | ASTM B363 WPT33 | ASTM B363 WPT34 |
ASTM B363 WPT35 | ASTM B363 WPT36 | ASTM B363 WPT37 | ASTM B363 WPT38 |
We manufacture an exclusive range of Titanium Sheet & Titanium Plates that are made supreme quality titanium sheets. Our range of titanium sheet & titanium plates are quality tested on various parameters before they are delivered to our clients spread across the globe.
Specification:- Grades Grade 1, Grade 2, Grade 3, Grade 4, Grade 5, Grade 7, Grade 9, Grade 23 StandardsGB / T 3621 -44 ASTMB 265
This is a Duplex alloy stainless steel designed to feature high strength, resistance to pitting, stress corrosion cracking, erosion corrosion and corrosion fatigue, crevice corrosion and strong weldability.
Super Duplex Applications
Oil and gas industry equipment, Offshore platforms, heat exchangers, process and service water systems, fire-fighting systems, injection and ballast water systems, Chemical process industries, heat exchangers, vessels, and piping, Desalination plants, high pressure RO-plants and seawater piping, Mechanical and structural components, high strength, corrosion-resistant parts, Power industry FGD systems, utility and industrial scrubber systems, absorber towers, ducting, and piping.
Super Duplex Corrosion Resistance
The high chromium and molybdenum content of Super Duplex makes it extremely resistant to uniform corrosion by organic acids like formic and acetic acid. Super Duplex also provides excellent resistance to inorganic acids, especially those containing chlorides. The pitting Resistance equivalent of Super Duplex, calculated by PREN = Cr + 3.3Mo + 16N, will exceed 40 in most material forms.
Forms of Super Duplex
Sheet, Plate, Bar, Pipe & Tube (welded & seamless), Fittings (i.e. flanges, slip-ons, blinds, weld-necks, lapjoints, long welding necks, socket welds, elbows, tees, stub-ends, returns, caps, crosses, reducers, and pipe nipples), Welding Wire and Welding Electrode
Properties of Super Duplex
Alloy Designation | UNS | BS | EN | Basic | DIN | JIS | Trade Name | ASTM |
Alloy | S32750 S32760 | 1.4410 | 25Cr-7Ni-4Mo-0.3N | SAF 2507 | A789 |
We offer Premium quality Nickel Alloy Plate and Sheets, which is designed to meet with various industrial functions. These nickel plates and nickel sheets are offered by us in a variety of sizes and is offered at industry leading prices.
Specification:- Grades Nickel 200 (UNS No.2200), Nickel 201 (UNS No.2201), Nickel 205 (UNS N0.2205) StandardsASTM / ASME SB 162 / 127 / 424 /168 / 443 / 574 / 462 Sheets & Plates In Form OfCoils, foils, shim sheet, perforated sheet, strip, flats, blank (circle), ring (flange), etc.
Stainless Steel Forged Fitting is high tensile strength, strong, stable, corrosion and rust resistance as well as their high efficiency. We manufacture these forged fittings using premium quality materials in accordance with the quality standards. These products are available in various sizes, shapes and design as per the specific requirements of our clients. Our esteemed clients can avail from us these products at most reasonable prices.
Specification Grade Stainless Steel 202, 303, 304, 304L, 309, 310, 316, 316L, 316TI, 317, 317L, 321, 410, 416, 420, 430, 440C, 904L Size 15 NB To 100 NB Types UnionCouplingFull CouplingCrossForged ElbowHex NipplePlugBushingBossInsertAdapterSocketForged TeeOletsWeldoletSockoletElbowletThredoletNipoletLatroletSweepoletHalf Coupling ApplicationPetrochemicals PlantsChemical PlantsIndustrial Machinery Power IndustryGovernment Companies