Impex Trading Company

Kalbadevi, Mumbai, Maharashtra

1. Heating the tube surface by low voltage high-current short so that the MgO & heater will get little heat.

2. Time relay controls the annealing time.

3. Eight kinds of power and voltage can apply to various specifications of tubes.

4. Pneumatic clamping, safe and convenient.

5. Flexibie design of collet, . There will be little bend when heat extension.

1. Power supply : Triphase 380V, 50Hz

2. Air supply : 5-7 kg/cm²

3. Rated power: 30KW

4. Applicable tube diameter: 6mm-20mm

5. Applicable tube length: 150 mm -1000 mm

6. Size ( LxWxH ) : 1500x600x 1500(mm)

7. Weight : 500kg

1. Vibrating disk select and feed the material automatically.

2. PLC automatically controlled, easy to operate.

1. Power supply: single-phase 220 V, 50Hz

2. Rated power: 200W

3. Efficiency: 30000 - 40000sets/8h

4. Size ( L * W * H ) : 1200*600*850 ( mm )

5. Weight: 1OOkg

1. Pneumatic clamping, start cutting automatically. 2. Element rotates, automatically stop when loading finished,

3. Burr-free ends on the tubes, high efficiency, easy to operate.

1. Power supply: Triphase 380V, 50Hz

2. Rated power: O, 8KW

3. Air supply: 5 -7kg/cm2 4. Efficiency: 8000pcs -1OOOOpcs/8h

5. Size ( LxWxH ) : 800x500x900(mm)

6. Weight: 120kg

1. PLC controlled automatically, load and cut material automatically.

2. Two kinds of sawblade speed, pneumatic convert to hydraulic and the speed of sawblade is adjustable.

3. V-shaped collets move at the same time. ( 8.0mm tube, clamp 25pcs at a time)

4. Tube length after cutling: 200mm - 2300mm

5. Jaw opening: 1OOmm

1. Power suppiy: Triphase 380V, 50Hz

2. Rated power: 1.6KW

3. Air supply: 5 -7kg/cm2

4. Efficiency: 30000pcs - 50000pcs (8.0mm copper tube)

5. Size (LxWxH) :1500x800x1500(mm)

6. Weight: 550kg

1. Test the speed and cut the tube automatically.

2. PLC automatically controlled, touch screen operation.

3. Encoder read the data of length which assure the precision of cutting length.

4. Even tube end and little burr.

1. Power supply: Triphase 380V 50Hz

2. Air supply: 5-7 kg/cm²

3. Rated power: 2.8KW

4. Applicable tube diameter: 5mm-12mm ( It can be custom-made)

5. Applicable tube length: 300mm -6000mm

6. Size (L* W * H) : 1800*700*1500 (mm)

7. Weight : 850kg

1. The height and angle of rollers are adjustable, can satisfy kinds of specifications.

2. Adopts hyperboloid roller design which can improve the surface and roundness of tubes.

3. Six durable alloy tool steel rollers.

4. Easy to operate.

1. Power supply: Triphase 380V, 50Hz

2. Rated power: 1.5KW

3. Applicable tube diameter: 5mm - 21mm (over this range can be custom-made)

4. Applicable tube length: 250mm

5. Size (LxWxH) :1300x700x1200(mm)

6. Weight: 360kg

1. PLC automatically controlled, human-computer interface. One man can operate three or four machines simultaneously.

2. The elements are automatically loaded, and then centered so the same amount will be cut from each end, thus ensuring that the original length can be maintained.

3. Show how to clear the error automatically.

1. feeding automatically by chain, deburr both ends at the same time.

2. deburr both inside and outside of tube ends at the same time by high-speed steel wire wheel.

3. easy to operate and adjust the tube length.

1. power supply: triphase 380v, 50hz

2. rated power: 3.5kw

3. efficiency: 60000pcs/l8h

4. applicable tube diameter: 6mm - 12mm (over this range can be custom-made)

5. applicable tube length: 1oomm -750mm

6. size (lxwxh) : 1900x1800x1200(mm)

7. weight: 580kg

1. The machine can feed the coil, terminal pin, assembling and welding automatically.

2. Easy operation, high production.

1. Power supply: Tri-phase 380V10%, 50HZ

2. Rated power: 11 KW

3. Air supply: 0.5 - O.7MPa

4. Pin length: 47-100mm

5. Coillength: 50 - 300mm

6. Coil diameter: 0.2 - 0.6mm

7. Efficiency: 900 - 1400pcs/h

8. Size(L * W * H) : 1800*1700*1800(mm)

9. Weight: 900KG

1. Automatic feeding, no operator is required.

2. Tube diameter, length, print location can be adjustable.

3. Easy to operate, stable quality

1. Power supply: Single-phase 220V, 50Hz

2. Rated power: 200W

3. Air supply: 5-7kg/cm²

4. Applicable tube diameter: 5mm - 20mm

5. Applicable tube length: 150mm -700mm (over this range can be custom-made)

6. Efficiency: 15000pcs - 20000pcs/8H

7. Size (L* W * H) : 1150*630*1200(mm)

8. Weight: 230kg

1. The tube diameter can be adjustable, easy to operate

2. Durable imported polishing roller. 3. Low noise, high quality.

1. Power supply: Triphase 380V, 50Hz

2. Rated power: 1.7KW

3. Applicable tube diameter : 5mm - 20mm

4. Size (LxWxH) : 900x800x1000 (mm)

5. Can make multi-stations polishing machine to the requirement of customers

6. Weight: 200kg

1. Application range: electric kettle, coffeepot. fryer and other products.

2. 0peration mode: manual time control.

3. Small size, compact in structure, easy operation and good design.

4. High production, stable performance, good welding. It can work 24hours continuously.

5. It can also equip with whole set cooling system (including water tank, pump and corresponding spare part)

6. Air supply control to avoid pot deforming for heating. It can make the weld joint better and better quality.

1. Power suppiy: tri-phase 380V 50Hz

2. Power: 25KW, 30KW, 40KW, 60KW

3. Water supply: water pressure 2-3kgf/cm², input water temperature< 30^oC, water flux: 2x40L/MIN

4. Air supply: 4-6kgf/cm²

1. Cylinder drive, easy to operate, no power supply require.

2. Tube diameter is adjustable.

1. Air supply : 4-7 kg/cm²

2. Applicable tube diameter : 5mm - 20mm

3. Applicable tube length : 100 mm

4. Efficiency : 5000pcs - 8000pcs/8H

5. Size (L * W * H ) : 600*380*880 (mm)

6. Weight : 100kg

1. vac sorb, convenient.

2. Subpressure switch protect

3. subpressure protecting when start and stop

1. Power supply: Triphase 380V, 50Hz

2. Rated power: 800W

3. Air supply: 5-7kg/cm²

4. Size (LxWxH) :600x600x1100 (mm)

5. weight: 11Okg

1. The tube diameter and length can be adjustable.

2. Deburr tube ends by high-speed wire wheel.

3. Easy to operate, high efficiency, good quality.

1. Power supply : Triphase 380V, 50Hz

2. Rated power : 1.5KW

3. Efficiency : 20000pcs/8h

4. Applicable tube diameter. 4mm - 20mm

5. Applicable tube length : 150mm

6. Size (LxWxH) : 600x620x1200(mm)

7. Weight : 130kg

1. Pneumatic clamping and feeding. 2. Cutter rotate while the element not. safe and convenient operation. 3. Hydraulic speed governor control the turning speed, stable quality.

1. PLC automatically controlled, human-computer interface and control the oscillation frequency by electron speed regulator.

2. Powder filling density could be above 2.17g/cm3 Almost zero MgO loss.

3. Tube diameter : below 16mm; Tube length: below 3000mm. It can be custom-made.

4. Digital tube length adjustment. The guide tube moving speed controlled by frequency control.

5. lndicate how to clear fault automatically.

6. It can fill 24 pcs or 36 pcs tubes at a time. The efficiency can reach 6500pcs/8h ( take 250mm long tube for example)

7. 12, 18, 24, 36 and 48 position machines are available to suit customer's production requirements.

8. Min. tube diameter: 5.5mm

1. Argon arc welding, good quality.

2. Autorotation welding. 3. It can adjust the center of a circle according to the tube diameter.

4. Tube diameter: below 25.4mm (can be custom-made)

1. Power supply: single phase 220V+/- 10% 50Hz

2. Rated power: 5KVA

3. Efficiency: 4800pcs/8h 4. Size: 13S0*900*1900(mm) 5. Weight: 150KG.

1. PLC automatically controlled, human-computer interface and control the oscillation frequency by electron speed regulator

2. lt adopts three guide tubes structure which has solved the problem that it is difficult to guarantee the center degree of long tubes

3. lt adopts self-locking powder device which assure that almost zero MgO loss.

4. Vibrator guarantee the powder density and the density could be above 2.20g/cm3

5. The guide tube moving speed controlled by frequency control.

6. Big and small powder box design. Electronic adjusting the exerted length of terminal pin.

7. indicate how to clear fault automatically. 8. 12, 18, 24, 36 and 48 position machines are available to suit customer's production requirements.

9. Tube diameter : below 16mm, tube length:beow 6000mm. lt can be custom-made.

1. Power supply: 220V, 50Hz

2. Rated power: 2.0KW

3. Air supply: 5 -7kg/cm2

4. Efficiency: 6500pcs/8h(tube length 250mm)

5. Size (LxWxH) : 1800x850x3300(mm) (1meter tube)

6. Weight: 600kg

1. the principal axis speed controlled by japan mitsubishi transducer. Continuously coils electric resistance and consistent clean-cut ends on the coils.

2. the machine will produce coils with very consistent resistance values and with open inside diameters for assembly to the terminal pins.

3. when lack of wire or wire is broken, the machine would stop automatically. It also can accumulate the output automatically.

4. wire with small diameter is usually cut by galvanomagnetism while wire with large diameter is cut by cylinder.

5. this machine is of small size, easy to operate, no operator is required.

6. wire with large diameter can adopt double-pinch roller type.

1. power supply : 220v, 50hz

2. rated power : 500w

3. main axis speed : o -2134rpm

4. pinch roller speed : o -74rpm

5. accuracy : +/ 1 %

6. i.d. Of element : 0.75mm -12.7mm

7. wire diamete : 0.1 omm - 0.85mm

8. size (lxwxh) : 1800x700x700 (mm )

9. weight : 130kg