HORIZON ENTERPRISE

Paschim Vihar, Delhi

A handy pocket caliper, made from solid brass. Close tolerance dovetail design ensures smooth motion of the caliper and provides accurate measurements. Graduated in both imperial and metric graduations with a least count of 1/16" on the imperial scale and 0.1 mm on the metric scale, these are ideal for use by mechanics, hobby crafters etc. who need to take measurements on small objects such as nails, screws, lenses, tubing etc.

These are available in two types:1. Brass Calipers (Outside)2. Brass Calipers (Inside and Outside) 1) Brass Calipers (Outside) Used for making external measurements from zero to the measuring range of the caliper2) Brass Calipers (Inside and Outside) Used for making both internal and external measurements. External measurements can be made from 0 - 4" (0 - 100 mm), whereas internal measurements can be made from 7/32" (5 mm) to 4" (100 mm)

A versatile tool, the Depth Gauge with Protractor allows for measurement of both angles and depths.

1. Manufactured from stainless steel, the protractor head has permanent deep etched graduations, 0-180 in opposite directions, thus permitting reading an angle directly and also its supplement
2. Depths are measured by a 6" (150 mm) steel rule. It is graduated in imperial dimensions on one side and metric on the other and can be set at any desired angle for use as a protractor and lengthwise when used as a depth gauge. A knurled thumbnut locks the rule in the desired position
3. The gauge has a flat surface on the back of the head permitting laying the tool flat upon the work. The rectangular head provides additional convenience as it incorporates 4 working edges
4. Angular Tolerance: 0.5
5. Head : Round & Rectangular

Perfect for marking on parts of different thickness. This special device provides easily adjustable impact force. Also suitable for sheet metal work. (riveting, flaring, piercing, shearing, bending etc.) Hand models and pneumatic models available.

IP-1100 MAXIMUM ADJUSTABLE STRIKING LOAD CAPACITY OF 1.1 TON

IP-3500 MAXIMUM ADJUSTABLE STRIKING LOAD CAPACITY OF 3.5 TON

Automatic Rotary Numerator with 6 wheels, with a special design to ensure that figures advance one-at-a-time accurately and automatically .

Consecutive serial numbers can be marked on metal parts in simple operationSpecial design ensure that figures advance one at- a--time accuretely and automatically.Impression are perfectly aligned, evenly spaced, uniformally deep-part after part!

Wheel made from special toolsAdvancing cams machined into solid wheelsExtra wide unit wheel for longer lifeOpen piece actuating pawl machined from solidDirect reading character to check set upHolding catch and spiring of unique design

Manufactured from Flat Steel.

1. Rivited head to give rigid position without play.
2. Just twist the nut and each reamer expands to the smallest size of the next larger size
3. Tension can easily be adjusted as desired.

We are engaged in making available dimensionally accurate Interchangeable Steel Type Die Punch Set. Interchangeable Steel Type Die Punch Set, offered by us, is highly durable and rust resistant. The Interchangeable Steel Type Die Punch Set is in compliance with the highest quality standards.

Lokriya.Ranglepak.Harris Single.Harris Double.

Double Ended one piece boring bar have 90 & 45 square ends.
They are supplied with Allen key and Screw but without tool bits.
Shiny Black Finish.

Product Description :

Rotary type numerator is specially designed to mark serial numbers, part numbers or code numbers on steel, alumunium; brass etc.This rotary type numerator is ideally suited for steel producers. Some key features of this rotary type numerator are as follows:

1. Perfect -time saver for repeat number by hand stamping 2. Serial numbers, part numbers or code numbers can be marked compact in size3. marking wheels` can be rotated to any designed positions, then locked positively by a locking pin 4. Individual release 5. No loose parts 6. Wheels made from special tool steel 7. All part treated to remove scale and plated to resist rust

It is used to scrape extra material and is widely used by jwellers and watchmakers.

Made from high quality tested carbon steel.
Special material and double induction hardening give very high quality of stamping.
Head is tempered to prevent chipping while hammering.

An excellent range of general purpose steel squares Whilst ideal for everyday workshop use, these are also suitable for woodworking applications

1. Both the blade and stock are accurately ground which ensures straightness and parallelism2. This range of squares comes in handy for setting up and checking machinery, checking Carpenter's squares or using as a trysquare when marking joints or testing faces & edges

The ability to measure depths and angles is combined in this versatile tool.

1. The head is made from selected steel and has an attractive black finish. It is graduated both left and right to 15, 30, 45 and the rule can be set to any of these angles
2. A 6" (150 mm) steel rule is fitted to the head and can be locked in final position for depth or angular measurements by a knurled nut

Made from stainless steel, these rules have a polished finish with permanently engraved clear to read graduations.

These are available in two types:
1. Imperial & Metric Combined Rules2. Metric Rules

These rules are graduated in metric dimensions on one edge and imperial on the other.Imperial dimensions are in 1/16th, 1/32nd & 1/64 ths. Metric dimensions are in 0.5mm & mm. Reverse side of the rule has a permanently engraved metric to imperial conversion table3. All reamers marked with sizes

Graduated in metric dimensions 0.5mm & mm on both edges

Drop forged from specially drawn medium carbon steel, these Drift keys are accurately hardened for increased resistance to wear.

Used for conveniently removing taper shank drills and remers from sleeves and sockets, these are blackened and have a premium shot blast finish with permanent marking of size for easy identification.

A basis tool for machinists and toolmakers, the Universal Surface Gauge is used for accurately scribing lines, transferring measurements or probing surfaces in inspection work.

Design incorporates:
1. A fully hardened and ground base which serves as an accurate reference surface.
2. A machined Vee groove in the base allows the gauge to be used conveniently on curved surfaces.
3. A Vee groove at the front end allows the spindle to adjust to any angle above or below the base allowing it to be used as a height gauge and also as a depth gauge.
4. Two retractable pins allow the gauge to be located against the edge of a surface plate or T-slot for linear work.
5. Grooves on the side of the base allow for comfortable grip.
6. Well tapered scriber for better sighting while working. The scriber tip is hardened to 55-60 HRC.

Scrapers are used for smoothing, cleaning, and deburring plastics and metals. With their hardwood handles they prepare the surface for soldering, removing excess solder and opening bezels. Can be resharpened on a bench stone.

Total length 7" with a 2-1/2" blade length.

Adapter Collect Pin Chuck Set, holds Drills upto 2.2mm, Shank 3/32"
Weight: 15 gms/pc

Basic tool for scribing and marking, Scribers can be used in metal, glass, plastics and ceramics.

Scribers are finely tapered permitting better sighting during work. A comprehensive line of steel and aluminium body scribers for machinist's, engravers, mechanic's and craftsmen.

a) Light weight double ended scriber with one straight point and the other bent at 90 making it convenient to use in confined spaces.b) Three Point Scribers. Finest quality scriber with aluminium body knurled for comfortable grip. Comes with 3 interchangeable threaded steel points: short straight, short bent & long bent which thread into the body.c) Two Point Scriber. With aluminum knurled body, this scriber consist of short straight and short 90 bent steel points which thread into the knurled body.

a) Steel body with 3 interchangeable threaded points, short straight, short bent and long bent. Very handy ad different combinations can be used for different applications.b) Single ended light duty. c) Tungsten carbide tip for marking on hard materials. Permanent magnet on the other end for picking up small metal parts.d) Scriber with pocket clip. Scriber point is held by a knurled chuck and can be reversed when not in use preventing tearing of clothing hen clipped on a pocket.e) Single ended heavy duty.f) Double ended. Combining a needle point point with a chisel end. g) Double ended with one straight point and the other point bent at 90 making it ideal for use in confined spaces.h) Double ended heavy duty with one straight point and the other bent at 90. Ideal for heavy marking jobs in confined spaces, grooves etc.

a) Pocket Scribers with replaceable hardened and ground tool steel points. Point reverses into the knurled body for safety. Hex head cap prevents the scriber from rolling down. Used for marking & scribing on steel, copper, brass and aluminium.b) Replaceable Needle Point Scriber with 4 extra needle points. Plated steel body with knurled handle and hex cap that prevents the scriber from rolling down. Spare needle points are stored in the handle under the cap. Used for marking & scribing on metal, glass, plastics & ceramics.c) Single Point Scriber. Knurled steel body with hardened and tempered point.

Manufactured from high grade steel, these toolholders are accurately machined and ground.

Toolbits are held parallel and straight to the shank giving maximum support to the cutting edge. Set screws are made from heat treated alloy steel with hardened points for increased resistance to wear.
These are available with straight shank, right handed or left handed offset shank.
Each holder comes complete with an allen key but without toolbit.

Manufactured from high grade steel, machined and ground to precise tolerance, these cut off tool holders support the blade over a wide area thereby reducing the possibility of blade breakage

The locking device enables the blade to be held securely and also enables rapid assembly. Especially designed clamp plate provides both downward and sideways pressure along a large area of the top edge of the tool ensuring complete rigidity

These are available with straight shank, right handed or left handed offset shank. Supplied with key but without blade

The rigid and robust construction of the range of knurling tool holders makes them ideal for countless knurling applications.

These are available in 3 types:
1. Knurling Tool Holders - 3 Pairs
2. Knurling Tool Holder - 1 Pair
3. Knurling Tool Holder - 1 Knurl

A-Grade : Made from carbon steel hardened and ground- internally and externally.
Workshop Grade : Made from carbon steel .
Reamed internally.
Externally ground and hardened

It finds application on drill presses, milling machines, planers etc. any place where leveling is necessary

Lifting capacity is approximately 1000 lbs (454 kgs)

Designed for versatility and accuracy, these Vee Blocks are ideal for holding round or irregular shapes for scribing, grinding, measuring, machining and testing applications.

1. These can be used either ways, up or standing on end, All Vee's and faces can be energised or de energised simultaneously by turning the rotary action control knob. This feature enables the Vee Block to hold both itself and the work on any flat ferrous surface including a permanent magnetic chuck (without energising the chuck).
2. Brass knob ensures no interference with the magnetic field, unlike the conventionally used steel knobs.
3. Also available with hardened Vee's: 55-60 HRC for increased wear resistance
4. For applications requiring two Vee blocks matched and numbered pairs are available

This quality reamer set creates precisely sized holes up to 1.5"! With just a simple twist, each reamer can expand to the smallest size of the next larger size in the set. Each reamer is constructed out of harden steel and is marked with its size for easy identification making this a great set of tools for any metal worker needing precisely measured holes in their sheet metal.

The attachments can be snapped onto the chuck without removing the collet nut and are clamped by a ball swivel joint which permits adjustment to an angular position

With needle point shark, working centers can be accurately located. Spring tension on the ball of the point permits guiding the point to true concentricity bringing perfect alignment between the work and machine spindle

Wiggler with Ball Contact is useful in locating work by first bringing the ball contact against the work and then indexing it to the desired position relative to the spindle

Wiggler with Offset Indicator holder is useful for checking run out or concentricity and in checking straightness or alignment of flat surfaces

Description Center Finder complete

with 4 attachments

This range of tap wrenches are ideal for holding taps, reamers, screw extractors and other such small hand turned tools. All wrenches have a sliding T handle frictionally held, that allows these tap wrenches to be used even in confined spaces.

These are available in two types:
1. Regular T Handle TypeSelf-centering hardened steel jaws provide a positive grip on taps, reamers and other such small tools.
2. Ratchet TypeThese tap wrenches have self centering hardened steel jaws and knurled chuck sleeve, which provide positive grip on taps, reamers and other such small tools. The ratchet can be set left or right, or direct engagement in neutral position. This feature allows them to be used in confined areas with ease.

Product Description :

Ideal for short or medium run threading of shafts etc. these holders are most convenient for use on lathes, milling machines, tapping machines etc.

Manufactured from solid one place steel, these have a rust proof black oxide finish. Main body is counterbored for chip clearance

The Pin Chuck is a very useful reducing chuck used for holding drills too small to be held by a regular chuck. It is gripped in the larger chuck already on the machine by means of the back shank. Supplied with three interchangeable collets for holding small drills in varying sizes

We offer qualitative array of Drill Chuck Arbor for Drill Chucks, that is fabricated using superior grades of raw material. These drill chucks are highly appreciated by our esteemed clients for its apprehensive features and high tensile strength. Moreover, our range of Drill Arbors are widely used to mount a drill chuck or any other tool onto the machine such as drilling machine. Available in various specifications, these Drill Chuck Arbor can also be custom made as per the client specifications.

The Jacobs Taper (abbreviated JT) is commonly used to secure drill press chucks to an arbor.

Manufactured from selected steel, the legs are exceptionally rugged and well finished. The leg that holds the adjustable point is offset. The locating lug is incorporated in the straight leg.

1. These are very useful in layout work for locating and testing centres, laying off distances from an edge etc.
2.Working faces hardened to 58 HRC

A range of angle plates is made both in plain and slotted types, with slotted types further available in open end and webbed end types. Manufactured from close grain cast iron. All the working faces are ground to 90 degree and true to each other. Jobs can be clamped to angle plate with the help of clamps. Angle plates can also be bolted to machine table.

Plain Angle Plates Thickness (in mm) 20, 22, 25, 28, 31, 33, 36 Slotted Angle Plates Note :- Available in open end as well as webbed end

Manufactured from high tensile, malleable cast iron, with an attractive grey hammertone finish, these are very useful for holding workpieces securely for smooth and even turning.

Used in conjunction with a catch-plate, these act as a driving device while turning material between centres.
A 'V' groove in the body helps clamping of round jobs.

This range of die holders is best suited for applications requiring efficient and clean cutting of external threads. Die holders have a rugged construction with heavy duty set screws that hold the die firmly in place.

These are manufactured in two types:
Bodies with chrome plated handles.
All steel construction with black powder coated body. Handles have knurled ends, the ends being black powder coated.

Made of Hardened and Ground high Carbon Steel.
Hardness 55 to 62 HRC.
Consists of two 'anti-friction' Bearings.
Single Row Deep groove ball bearing and Taper Roller bearing to absorb combined radial and thrust loads.

Manufactured from selected steel, accurately hardened, this is an excellent tool for boring through holes or to a shoulder.

The angle permits maximum sweep diameter with minimum tool projection and can machine upto 6" wide surface with a standard tool bit.
Complete set consists of 3 fly cutters with shank fully counter balanced to ensure a smooth finish.