Hind Electrical Co.

Gidc, Vapi, Gujarat

• Standard or Nonstandard:Standard
• Structure:Pressure Reducing
• Pressure:Medium Pressure
• Power:Manual
• Material:Stainless Steel
• Temperature of Media:Medium Temperature
• Media:air/gas
• Port Size:DN32-DN150
• Application:General
• Connection:Flanged RF ANSI B16.5
• Connection1:BSP NPT thread 1/2"-2"

This Cast Steel Gate valve features a bolted bonnet with Class 150 to Class 1500 flanges in sizes 2 to 30. The one piece flexible wedge with a tapered H shape is fully guided and suitable for steam and other high temperature service. The yoke sleeve is designed to allow for disassembly without disconnecting the bonnet and stem. Standard body materials are A216-WCB, A217-WC6 or A351-CF8. Depending on service conditions, other material options are available for valve and trim.

Sizes: 2 30

Larger sizes are available upon request

ANSI Class: 150 1500

Features: API 600/603, Testing to API 598, Bolted Bonnet/Pressure Seal Bonnet, Outside Screw & Yoke, Flexible Wedge, Fully Guided Wedge, Rising Stem, Standard/NACE

Body: Carbon, Alloy or Stainless Steel (WCB, LCC, WC6, C5, C12, CF8)

Trim: Trim 5, Trim 8, Trim 16

End Connections: Raised Face (RF), Flat Face (FF)

Also available in RTJ and Butt Weld

*Additional sizes and materials available upon request. Availability is dependent on market demands

FUNCTION

Gate valve is characterized by a sliding wedge which is moved by actuator perpendicular to the flow direction. There are a variety of valve sizes and types. The valve is used primarily as a stop valve to open or close fully. Normally it works for slurries, viscous fluid, etc. but not for throttling. The gate valve usually has a minimum pressure drop in full open and a tight seal in full close, and therefore there is little possibility that contaminants may enter the valve.

BODY AND BONNET

The body and bonnet is designed to achieve most uniform distribution of stress on all sides and minimum turbulence and resistance to flow. The bonnet on valve is equipped with back seat ring up to 12" for Class 150 & 300 and up to 10" for Class 600 or higher. The yoke is integrated with bonnet.

BODY AND BONNET JOINT

Body-bonnet joint of gate valve is machined as follows:

Class 150 . Plain faced

Class 300 and higher class . Male and female

We can supply any kinds of gasket as required by customer

WEDGE

The valve is normally supplied with a one-piece flexible wedge of which the cross section is a tapered H shape.

All wedges are fully guided. The flexible wedge is cast or machined with circumferential grooves to allow the seating faces to move independently and adjust the movement of body seat.

It is used where the line load or thermal expansion of system may distort the seating face of valve, and especially useful to prevent sticking that may happen in case the valve is closed at a hot temperature and opened at a cold temperature.

Ideally the wedge is suitable for steam and other high temperature service.

SEAT RING

The stem connection to the wedge shall have an integrated tee head (without welding)and is rectified in the packing area to ensure a long life and perfect tightness. Through experiments, we have calculated and checked the connections between stem and wedge not to disengage the stem from wedge while gate valve is working.

The strength of stem and wedge connections is stronger than that of stem alone at the root of thread.

STEM

The packing size is designed to secure maximum tightness along the stem, and the standard packing is a non-asbestos type. We can supply any kinds of packing as required by customer.

We are offering butterfly valve. a type-butterfly valve wafer type butterfly valvebody : cidisc : ci shaft : aisi 410lining : nitrilepressure : pn16 106design : bs 5155testing : bs 6755.

Easy structures and short dimensions are the remarkable features of dual plate check valves They are to be directly mounted between DIN flanges (PN 10, PN 16 or ANSI 150).

Dual plate check valves require a low opening pressure. The resulting opening power directs the stems against the spring and the valves weight power, so that the media is released. If the initial pressure is higher than the entrance pressure, the valve closes and is sealed by the O-ring to protect it from the media.

Dual plate check valves type are designed to block media on one side of the pipe within allowable pressure and temperature limits and to be installed in a pipe system only. They are only to be used with media, which the material and the seals are resistant to. They are not suitable for media with solid components.

Installation compared to other type of check valve.

The Dual Plate Check Valve employs two spring-loaded plates hinged on a central hinge pin.

When the flow decreases, the plates close by torsion spring action without requiring reverse flow.

This design offers the twin advantages of No Water Hammer and Non Slam simultaneously.

All features put together make the Dual Plate Check Valve one of the most efficient designs.

Power Plants

Water

Fertilizer Plant

Chemical Plants

Oil and Gas Processing

Refinery

Cryogenic Service

General features

Design type	Swing, piston, ball, dual plate, nozzle check
Size ANSI	0, 25 - 16
Pressure ANSI	150 lbs - 4500 lbs
Size DN	DN 6 - DN 400
Pressure PN	PN10 - PN 400
Design temp.	minus 196 C up to 816 C
End connections	Flanged, Wafer type, BW, SW, HR, HUB
Options	Pressure seal cover, soft and metal seat
Design features	Retainer less design
Design & testing	All available international standards according to API - EN - ISO

We are pa rominent Two Way Globe Valve Manufacturer, Supplier and Exporter In India. Our Two Way Globe Valve with its classic globe body shape, which reflects its name, uses the variable area generated between the plug and seat to control fluid flow. The Two Way Globe Valve is very versatile offering reduced trim options as well as a variety of special trims for severe high-pressure drop applications. The Two Way Globe Valve is easily adapted for use on cryogenic temperatures and for high temperature duties. Two Way Globe Valves are preferred for tight shut off, positioning accuracy, high range ability and simplified maintenance, satisfy the majority of control valve applications throughout the process and power industries in control of Air, Steam, Water, Gas, Chemicals, etc. Technical Specifications

• Design : ASME B16-34
• Valve Size : 15 to 450 mm ( 1/2" to 18" )
• Rating : ANSI 150 to 2500 or Equivalents to BS, DIN, etc.
• Face To Face
  • ISA S.75.03 1985 up to 600
  • ISA S.75.16 900 and above
• End Connection : Flanged, Screwed, Butt Weld, Socket weld.
• Body Materials : Carbon Steel, Chrome-moly Steel, Stainless Steel, Monel, Alloy20, Hastelloy B/C, PP, PTFE etc. PTFE Lined / PTFE Metal Housed
• Bonnet
  • Standard upto 250^oC
  • Normalizing (Finned) between 250^oC to 500^oC
  • Extended cold service - 20^oC to - 200^oC
  • Extended Bellows seals
• Gland packing : Grafoil / PTFE V Rings.
• Trim designs : Top Guided Contoured, Splined Micro Flow, V-Ported (Balanced / Unbalanced), Low Noise ( LN1, LN2, LN3, LN4 )
• Trim materials : Stainless Steel, Alloy20, Monel, Hastelloy B/C, Satellite Alloy 6 )
• Characteristics : Equal Percentage, Linear and Quick Opening.
• Seat leakage : As per FCI-70-2 (ANSI B 16.104) Class III. IV, V and VI (standard leakage rates) Metal to Metal Seating Class IV, Less than 0.01% of rated Cv. Metal to Soft Seating Bubble tight (Zero Leakage)
• Actuator type : Diaphragm, Cylinder or Electric.
• Actuator action : Direct / Reverse Acting.
• Diaphragm : Nitrile / Neoprene.
• Spring ranges
  • 15 PSIG ( 0.2 - 1.0 Kg/cm2 )
  • 6 - 30 PSIG ( 0.4 - 2.0 Kg/cm2 )
• Air Supply : 20-35 PSIG (1.4 - 2.5 Kg/cm2 )
• Air Connection : 1/ 4" or 1/ 2" NPT
• Handwheel : Top or Side Mounted Handwheel
• Accessories : Valve Positioner - Pneumatic, Electro Pneumatic
• Optional : Smart Positioner, Airset, Solenoid Valve, Air Lock, Volume Booster, I/P Converter, Position Transmitter, Limit - Proximity Switches etc. Removable Blind Head, Steam Jacketing, etc.

We offer globe valve, c.s (w.c.b) globe valve.(flenge end).

We are the most reliable Pressure Regulator Valve Manufacturer, Supplier and Exporter In India. Our Pressure Regulator Valve is mainly used to handle downstream pressure and is self-contained and self-operated control device, which uses energy from the controlled system to operate & regulate pressures. Our Pressure Regulator Valve helps to manage downstream system pressures in low, medium, high flow applications. The different models of the valve include a diaphragm type, piston type or combination of both to suit different applications. A Pressure Regulator Valve maintains a desired reduced outlet pressure while providing the required fluid flow to satisfy a variable downstream demand. The valve at which the reduced pressure is maintained is the outlet pressure setting of the regulator. Principle Of OperationAll type of regulators generally fit in to one of the following two basic categories

• Direct Operated
• Pilot Operated

The specific considerations peculiar to your control needs is to be carefully studied and understood to determine which method of control is the better choice. Regulators when compared to control Valve / Instrument package have their advantages and limitation. The operational principal of both types of regulators is explained as follows.

• Direct Operated : In operation, a direct-operated, pressure-reducing regulator senses the downstream pressure through either internal pressure registration or an external control line. This downstream pressure opposes a spring that moves the diaphragm and valve plug to change the size of the flow path through the regulator. Characteristically direct operated regulators are adequate for narrow-range control, and where the allowable change in output pressure can be 10 to 20% of the outlet pressure setting. This 10 to 20% is typical although finer control can be achieved depending on the specific application requirement.
• Pilot Operated : A pilot-operated system uses a two-path control. In two-path control, the main valve diaphragm responds quickly to downstream pressure changes, causing an immediate correction in the main valve position. At the same time, the pilot diaphragm diverts some of the reduced inlet pressure to the other side of the valve diaphragm, diaphragm control the final positioning of the main valve plug. Two-path control results in fast response. Pilot-operated regulators are preferred for broad-range control, or where the allowable change in outlet pressure is required to be less than 10 percent of the outlet pressure setting. They are also commonly used when remote set point adjustment is required for a regulator application.

We are offering Control Valve. IntroductionThis type of Valve with its classic globe body shape, which reflects its name, uses the variable area generated between the plug and seat to control fluid flow. It is very versatile offering reduced trim options as well as a variety of special trims for severe high pressure drop applications. This style of valve is easily adapted for use on cryogenic temperatures and for high temperature duties. This valve is preferred for tight shut off, positioning accuracy, high range ability and simplified maintenance, satisfy the majority of control valve applications throughout the process and power industries in control of Air, Steam, Water, Gas, Chemicals etc. We are one of the eminent Globe Valves manufacturers, exporters and traders, based in India. Technical Specifications DESIGN : ASME B16-34VALVE SIZE : 15 to 450 mm ( 12" to 18" )RATING : ANSI 150 to 2500 or Equivalents to BS, DIN, etc. FACE TO FACE ISA S.75.03 1985 up to 600ISA S.75.16 900 and aboveEND CONNECTION : Flanged, Screwed, Butt Weld, Socket weld.BODY MATERIALS : Carbon Steel, Chrome-moly Steel, Stainless Steel, Monel, Alloy20, Hastelloy BC, PP, PTFE etc. PTFE Lined PTFE Metal Housed BONNET: Standard upto 250oCNormalizing (Finned) between 250oC to 500oCExtended cold service - 20oC to - 200oCExtended Bellows seals.

We are offering pinch valve. hand wheel op pinch valves. body :-c.i. pinching bar:-c.i. wheel:-c.i. bridge:-w.c.b. bush for bridge:-g.m. spindle:-s.s. (410.)tai bar:-s.s. (410.)h-conection:-g.m. bolt, nut, washer for body:-m.s. (f.t). ruber sleeve: - re.neoprene.