Hi Tech Engineers

Vatva, Ahmedabad, Gujarat

Design to remove unwanted particles like Staples, Stones Screws, Nails, Pabbles and other debris from stock and it collected in the reject chamber.The Reject Chamber is provided with a glass which helps to observe the rejection collected in to chamber.Clogging free operation.It protects the rotating part of refiners, deflakers and other down stream equipment against excessive wear and breakage.Zero fiber loss.Motorized model is available.Customized HD cleaner up to 2500 LPM are also manufactured.Fabricated with S.S. 304 and 316 material.

It is the heart of a paperboard machine, It controls stick flow, pickup on the felt part and is responsible for good single layermulti layer formation & substance profile across the full web, Designed according to Production requirements, We also supply phosphorousS.S. Bronze spiders with bronze strips with 10 gauge S.S. wire wounding on request, Tapered flow header for uniform velocity condition. Design type of Vat, Uniflow Flow Vat- This type used for good formation of Craft board & duplex board.

Dryer Section designed to optimize the drying rate, reducing the investment cost, M.S. Fabricated dryers up to 2.0 mt. Dia and 25 mm to 36 mm shell thickness and the width up to 5 mt, Dryer is suitable for 4 to 5 kg cm2 operating pressure, The dryers are mirror finished and the width up to 5 mt, Our dryer system components are designed to provide best drying efficiency and uniform drying control, Heavy duty cast iron framing is also available its excellent for vibration dampening, The drying cylinder can be provided with stationary syphons or inside bucket system for proper removal of condensate, For high speed application above 200 mmin rope feeding arrangement is provided.

Slushing waste paperbrokevirgin pulp in a continues or batch operation, Low to medium consistency, M.O.C. S.S. 316 to M.S. Sandwitch plate fabricated & as per requirement, Poconsumptionis reduced, Dynamically balanced S.S. Pulper impeller with hydrodynamically designed vanes, Easy Maintenance, , Capacity up to 16 cubic meter.

Slushing waste paperbrokevirgin pulp in a continues or batch operation, Low to medium consistency, M.O.C. S.S. 316 to M.S. Sandwitch plate fabricated & as per requirement, Power consumption is reduced, Dynamically balanced S.S. Pulper impeller with hydrodynamically designed vanes, Easy Maintenance, Capacity up to 16 cubic meter.

It is the heart of a paper/board machine. It controls stick flow, pickup on the felt part and is responsible for good single layer/multi layer formation & substance profile across the full web. Designed according to Production requirements. M.O.C of Cylinder Mould. We also supply phosphorous/S.S./ Bronze spiders with bronze strips with 10 gauge S.S. wire wounding on request. Tapered flow header for uniform velocity condition. Design type of Vat. Counter Flow Vat- This type used for mainly in Board M/C & Slow Speed. Uniflow Flow Vat- This type used for good formation of Craft board & duplex board.

DRY VAT TYPE

• Increase in formation pressure.
• Shortening of the forming zone.
• Reduction in the amount of water carry-over from the inside of mould.
• Possibility of regulation the flow speed of stock suspension in forming zone.
• Reducing the effect of centrifugal force.

The Rewinders are designed for precision slitting and rewinding job having high speed winding drums, maximum operating speed is up to 700 MPM. M.S. Fabricated body with C.I. Slides & complete slitting arrangement. Optionally we provide Heavy Duty complete C.I. Body.Pneumatically operated Rider Roll with complete slitting arrangement removing of wound Roll is done by pneumatically operated pusher Roll.Uniforms tight winding of Rolls. Clean & smooth surface of Roll. Easy separation of slit Roll. (Without using wedges) . Easy and quick feeding of paper. Rewinder is driven by D.C. / A.C. Variable speed drive. For slitting arrangements we are provided pneumatically or Manually loaded knives

M.S. Fabricated drum & C.I. Framing. Reeler is designed on the principle of circumferential winding. We will provided auxiliary (primary) arms is pneumatically operated for loading & mechanical arrangements for shifting of reel. Working (secondary) arms is loaded for pneumatically. Before the reeler camber pipe or camber roll are installed for creasing free reeling. Having pneumatic loading arrangements which ensures tight reeling and automatic reeling change over system which reduces the loss during the change over. Maximum paper real Dia 2000 mm.

M.S. Fabricated M.G. Cylinder upto 16 ft dia & 4.2 mt. Width. M.G. Cylinder are made from ultra O.K. Plate. M.G. Cylinder suitable for steam pressure up to 175 psi. M.G. Cylinder are mirror finished. M.G. Cylinder can be provided with scooping system for removal of condensate efficiently. For vibration free operation we will provide, Heavy duty M.S. Fabricated frame. We also provide M.G. Cylinders with S.S. Coating surface. (Optional). We also provide M.G. Hood for improves production & saves condensation of vapor. Hood made from M.S./S.S. Fabricated (optional). M.G. Spur gear & pinion also provided in M.S. Fabricated/C.I./polypic material with hobbing cut teeth so it gives noise free operation.

Most suitable for kraft, liner, writing & printing or speciality paper because of Efficient water removal. High dryness achieved upto 50% in recycled furnish after this press in comparison to conventional press upto 45%. Production increase by18%. Improve the physical characteristic of paper. Improve stiffness & breaking length of paper. Less energy consumption (Power & Fuel) pertone of paper.

The highest possible dryness should be reached with least possible number of nips. Pressing must not impact paper quality. The press section should compact, Simple and rigid Structure. Hydraulic & Pneumatically loaded press rolls with heavy duty framing. Press section is designed for 180kg. - liner cm. load for efficient water removal. It is double felted first nip for two sided dewatering used for higher efficiency of press. Heavy duty press section with roll dia 430 to 1200 mm. For high speed application grooved or blind-drilled roll is available. Large diameter presses at high press load combine optimum performance with low investment, operation and maintenance cost. Production increase, reduced steam consumption and efficiency increases in case of rebuilt of an exciting machine.

Dryer Section designed to optimize the drying rate, reducing the investment cost. M.S. Fabricated dryers up to 2.0 mt. Dia and 25 mm to 36 mm shell thickness and the width up to 5 mt. Dryer is suitable for 4 to 5 kg/ cm2 operating pressure. The dryers are mirror finished and the width up to 5 mt. Our dryer system components are designed to provide best drying efficiency and uniform drying control. Heavy duty cast iron framing is also available its excellent for vibration dampening. The drying cylinder can be provided with stationary syphons or inside bucket system for proper removal of condensate. (Optionally). For high speed application above 200 m/min rope feeding arrangement is provided.

Designed for formation & drainage capacity optimization. Wire Section is available either with cantilever type or run out type wire changing arrangement. We also provide Top wire arrangements for multi layer & High gsm. Consist of lot of drainage elements such as forming board, hydro foils, high Vacuum box to improve sheet formation. All parts in contact with water or stock are made of S.S. and corrosion resistant materials. Complete S.S. cladding structure is also available.

Excellent former assembly for good formation and paper pick up of 32 to 120 gsm. Mould & vat completely made out of S.S. material. Suitable for machine up to 120mt. speed. Minimum profile variation. Tapered manifold for uniform velocity condition and evener roll for good defloculation. Zero fibers loss due to rubber sealing.

The Octopus Stock Approach System is used on a variety of head boxes, hydraulic formers, and vats to improve CD basis weight profile. This profile management tool permits the paper maker to minimize variation, improve sheet properties, and increase profitability.

Features

• All wetted parts stainless steel
• Automatic air pad pressure compensation control
• Optional CD consistency profiling
• Applicable to head boxes, hydraulic formers, and vats

Benefits

• Provides uniform CD flow/basis weight management
• Does not require operator to balance unit in response to Flow changes
• Dampens pressure pulsation
• Reduces entrained air
• Reduces fiber floc size

Vertical screen designed for fine screening of all kind of stock suspensions at low consistency range of 0.4-1.1% The screens are suitable for stock preparation system and also for approach flow system ahead of paper machine. The MULTIVANE AEROFOIL ROTOR design ensures the screen to operate free from pulsation.Low power consumption. Exceptional improvement in screening efficiency. Improve quality of paper. Dependable paper machine operation. Basket-hole or slot type. Excellent manufacturing fitness.

Baskets perforated or slotted foil rotor

• Multi vane aerofoil rotor.
• Pulsation free rotor design.
• Special rotor design avoids string formation.
• Gentle screening.
• For low consistency hole or slot basket.

The ideal screen for waste paper stock preparation (white and brown grade). The special rotor design allows the screen to operate at 3-4.5% consistency. The stock suspension is screened through a screen drum having perforation or slot, We offer gland or mechanical seal (option) arrangement, Low power consumption, Exceptional improvement in screening efficiency.Exceptional improvement in screening efficiency, Improve quality of paper, Dependable paper machine operation, Easy change over of belt and pulleys in minimum time.

Vertical screen designed for fine screening of all kind of stock suspensions at low consistency range of 0.4-1.1% , The screens are suitable for stock preparation system and also for approach flow system ahead of paper machine, The MULTIVANE AEROFOIL ROTOR design ensures the screen to operate free from pulsation, Low power consumption, Exceptional improvement in screening efficiency, Improve quality of paper, Dependable paper machine operation, Basket-hole or slot type, Excellent manufacturing fitness.

We are manufactures of hard chrome shaft.

We are suppliers of honed tubes.

We are supplier of ball screw.