Ahmedabad, Gujarat, India
Our Products
36 sizes and 226 rings. Sizes ranging from 006 (1/8" ID, 1/16" width) up to 327 (1-3/4" ID, 3/16" width). Buna 'N' material.
The DMRT Type W Mechanical Seal consists of two identical steel rings and rubber belleville washers. The seal operates by preloading the two rubber washers and fl oating the two polished steel faces between them within the seal chamber
Daemar offers a full range of Single Spring "Pusher" Mechanical Seals. Including the standard Types A, B, C, D and E. Which are equivalent to type 6, 6A, 21, 2, 1.
Since January 2011 LUTOS has offered a new range of energy saving screw blowers.The new LUTOS screw blower packages are based on screw compressor elements, which are due to the simple concept of their design and high reliability the most popular source of compressed air. In addition to 35% energy savings they alsooffer lower noise, high efficiency direct motor drive and reduced vibration and pulsation in the pipeline. The blower is supplied with an electric motor and on request can be supplied complete with an acoustic enclosure. * Average savings atpressure of 100 kPa.
Is the most popular LUTOS blower package, including complete accessories already in the basic price: - DI blower with three-lobe rotors- Supporting frame with outlet silencer- Silencer and air filter- Belt drive, including belt guard if the package is not assembled with sound enclosure- Safety valve- Start-up on bigger sizes- Check valve- Compensator- Filter clogging Indicator- Pressure gauge Blower packages can be supplied including fully connected electrical control unit and variable speed drive
The blowers for vacuum to minus 500mbar are based on the DT blower packages. The blower is additionally equipped with a vacuum valve which protects the blower from overloading. These blower can be used in vacuum pneumatic transport, paper and printing industries, agriculture, industrial vacuum cleaners, etc.
Compensation for Gamma background is crucial in tritium measurement, since a gamma field of 1mR/Hr will generate 500 times the ionization generated in 1Ci/m of tritium. Tyne designed the four, 250 cc ion chambers in a cruciform with each chamber connected to an ultra sensitive electrometer amplifier and filter. All signals pass through the ADC converter, and the micro-processor calculates and displays the tritium value. To cover high ranges of tritium a separate small ion chamber is used. Measurements such as flow from the solid-state flowmeter and chamber temperature are also monitored by the micro-processor.
Instrument output includes analog (0-5V, 4-20mA); relay alarm contact (30VDC, 1A) for operation of external equipment; and communication (RS232/RS485) to enable downloading or recording of information onto a computer. The TFT full color LCD display mounted on the surface plate clearly displays instrument readings in both digital and graphic format to show real time measurements and trends.
The well balanced, easy-to-carry instrument can be placed on its end for easy visibility of the touch screen monitors to operators working away from the instrument.
Batteries installed in the handle are easily replaced.
A powerful long-life pump can be used to draw air through a 10 meter tube. This allows the instrument to be used to measure the inside of rooms without the need to enter the room.
Special blowers vary in design, parts material, connections, the direction of air flow or they are used for other gases and mixtures. Their design meets non-standard customer requirements in projects where the use of the basic range is not possible. One of the most common application for special blowers is biogas.Production, purification and processing of biogas and the subsequent production of electricity is a growing segment of the market across Europe. In Germany alone there are currently more than 6, 000 biogas plants with total installed capacity of 2.3MW. Blowers produced according to ATEX directive 94/9/EC are supplied mainly in a classification II 3G IIA T3.
The BAH range has a unique design with flow performance up to 650 m3/h, this LUTOS design was awarded with a Gold Medal at the International Engineering Fair in Brno. BAH has the following advantages:- Minimum space requirements- Excellent Price to performance ratio- Air inlet atthe ambient temperature, even if using a sound enclosure- Sound enclosure without an extra fan
The O-ring is a simple and versatile seal that can be used in thousands of applications. O-rings are manufactured in a wide variety of compounds to suit your every need.
Static SealingMost O-Rings are used in static service (the O-Ring and metal surfaces remain relatively fixed). They may be applied as face seals or radial seals. In face seal applications, the O-Ring should seat against the low pressure side of the groove.
Dynamic SealingThe O-Ring moves relative to the mating surface. A moving seal may be further classified by the type of motion: reciprocating, oscillating, or rotating. The greatest number of dynamic seals are used in reciprocating service in cylinders, valves, and linear actuators. Oscillating motion is encountered in swivels and valve stems. When an O-Ring is used on a rotating shaft, it should be limited to light duty where the shaft speed is low and some fluid bypass is acceptable.
MaterialsBuna-N, Viton, EPDM, Silicone, PTFE, Polyacrylate
Durometer Selection70-durometer hardness should be used wherever possible as it offers the best combination of properties for most O-Ring applications. Softer compounds stretch easier and seal better on rough surfaces. Harder compounds offer greater abrasion resistance and resistance to extrusion.
Sizing Systems
AS568 Dash Sizes - Inch Sizes
Standard inch sizes ranging from 1/32" I.D. to 26" I.D.
AS568 Dash Size Chart
Boss Tube Fittings O-Ring sizes for Boss Tube Fittings are available in both 70 & 90 Durometer. These O-Rings are used in applications to provide a seal for straight-thread tube fittings on a boss.
Numbering System: The two digits after the -9 represent the Tube Size O.D. in 16ths of an inch. For example -905 is sized for a Tube O.D. of 5/16". The one exception is for -901 where the Tube Size O.D. is 3/32". Boss Tube Fitting O-Ring Size Chart
Metric SizesStandard metric sizes ranging from 1.50mm I.D. to 499.30mm I.D.
Metric O-Ring Size Chart
Daemar delivers a range of Mechanical Seal solutions from the standard Types A, B, C, D and E. Daemar can also supply custom seals such as our new Type W Axial Shaft Seal.
DI lobe blowers are used for special applications. DI elements can be used as a truck blower or a stand alone element driven by an existing engine.
Machined integrally from a block, the Machined T Valve normally features three common ports with the same bore dimensions and incorporates a valve body and a tee fitting into a single solution. Machined T valves form the ideal solution for feeding laterals off recirculating loops, sample points or use-point applications. The bodies can be supplied with weld or hygienic clamp end connections or included U-bend configurations for point of use.
| DEPA Air Operated Diaphragm Pumps, High Pressure Pumps, Series DB DEPA Air Operated Diaphragm Pumps are a cost-effective alternative in pressure-maintaining operation since any elaborate and costly closed-loop or open-loop control is dispensed with. Overview DEPA Air Operated High Pressure Diaphragm Pumps (series-M), type DB, are preferred by filter press operators. The DEPA high pressure pumps are factory set to 13bar (188psi), 16bar (232psi) or 21 bar (305psi). They can be operated at the required working point. The variable pressures possible with the DEPA pumps protect the filter press while the short filling cycles improve the productivity of the entire filter process. There are 3 sizes available so that the pumps can be individually adapted to requirements of the transfer tasks. While the body is made of cast stainless steel, various elastomer materials for diaphragms, valve seat, s and valve balls are also available. |
The Revo Series R range of actuators is ideal for operating quarter-turn valves, especially butterfly, ball and plug valves. Typical applications are 90 or 180 rotary motion and Multiposition function.
The linear counter movement of the pistons is transmitted into the required 90 travel by means of the integrated racks of the pistons and the pinion.
All Revo actuators are suitable for on/off or modulating control operations. Double-acting actuators are operated by air in both directions (open and closed) whilst single-acting actuators can be supplied with springs to open or close. On air failure these will then go into a fail-safe position.
We supply you with complete modules consisting of valves, actuators and accessories. We are independent from manufacturers and brands.
On the basis of your specifications we combine valves of any design with pneumatic, hydraulic and electric quarter-turn and linear actuators. The required range of accessories spans from Limit Switches, Solenoid Valves, Positioners to the interface of bus-systems. The Revo Actuator meets interfaces according to Namur and DIN ISO 5211.
Glass - Specialist blue borosilicate lining available in both weir and straight through designs.
* Cast Iron / Glass DN15-350 (" to 14")
Available in the weir type design and with a number of lining options to suit corrosive line service.
* PFA DN15 - 100 (1/2" to 4")* PP & ETFE DN20 - 150 (3/4" to 6")* PTFE DN150 - 250 (6" to 10")
Available in both weir and straight through designs and with a number of lining options to suit both aggressive and abrasive line service.
* A Type DN20 - 500 (3/4" to 20")* KB Type DN20 - 350 (3/4" to 14")
As the innovator and leader in diaphragm valves, we continually develop our diaphragm technology and remain the only manufacturer to have complete ownership of the research and development, design and production involved.
Saunders offers a full range of diaphragm selections engineered to meet the exacting demands of our industrial customers. All grades of rubber and PTFE have been developed to suit individual customer requirements and are proven, even in the most arduous environments.
All Saunders diaphragms are made from high quality materials and are manufactured in-house to strict quality standards. This is borne out by the fact that all diaphragms are fully traceable in accordance with EN10204 3.1. This gives our customers the assurance of consistent, reliable and repeatable quality resulting in consistent, reliable and repeatable process performance.
To assist in the selection of the best diaphragm materials please use the Saunders material selection program or alternatively, please feel free to contact our customer service group, who will be happy to assist you with the best recommendation for your application
The most common customized valve concept is the tandem valve or valve and fitting combination. A main valve is ported and a section of tube is welded to the port to create an access point into the valve. This tube can in turn be welded to a second valve forming a two-valve cluster, or the tube can be turned into a weld end, hygienic clamp or other type of fitting. The resultant product is designed to optimise drain ability and meets standard process considerations including camps for dead leg minimisation.
Size Range: DN15 DN 150 ( 6)
End Connections: A wide range of end connections is available. Please contact us for the full range.
Typical Applications: Product transfer purging, steam sterilisation, condensate drains, CIP systems
A resilient seated butterfly valve with superior design features and materials of construction to provide repeatable tight shutoff in severe abrasive and corrosive environments for a variety of applications.
| Design Features | Benefits |
| Full bore ody construction. | Free medium flow.Clear pass for maintenance and diagnostic equipment. |
| Seats with double sealing (primary - metal to metal, secondary - metal to elastoplastic). | Extended service life. |
| Corrosion-resistant gate. | Protection of the trim from abrasive wear-out and line medium deposits. |
| Drain pipe inside gate valve. | Removal of sediments containing hard admix. |
| Removable polyurethane ring gaskets and clamp connection "body-to-cover". | High level of maintainability and serviceability. |
| Usage of thermo expanded graphite for sealing gland. | Less stem friction wear-out.Extended service life of the element. |
Application Used as stop valves for pipelines transporting: oil, petrochemical products, synthetic oil and other explosive flammable liquids (Oil). |
||||||||||||||||||||||||||||||||||||||||||||
O-rings custom manufactured for your specific application needs. Available in inch or metric cross sectional sizes and a wide range of materials.
