Hexatec Instruments Pvt. Ltd.

Palghar, Mumbai, Maharashtra

• Triple walled in construction.
• Exterior made of Mild Steel [ 18 swg. ] constructed on thick iron angle framework. The entire outer body is duly painted by long lasting DUCO Paint.
• Pre-heating Chamber made of Mild Steel [ 20 swg. ] & Inner Chamber made of Stainless Steel [18 swg.]
• Gap between the walls filled with initial layer of Asbestos Sheets followed by a dense layer of high quality low thermal mass glass wool insulation.
• Provision for forced air circulation using motorized blower.
• Provided with control panel for monitoring temperature.
• Installed with a Microprocessor based PID Digital Temperature Indicating Controller with BUILTIN Timer
• DIGITAL HIGH TEMPERATURE SAFETY CUT-OFF INCORPORATED WITHIN THE UNIT.
• Superior quality contactor for cutting / restoring power to the heaters are incorporated.
• Doors provided with safety cut-out system disables the Motor & the Heaters when doors are opened in operational mode.
• Control panel with suitable neon lamps for indication of Mains On/Off. Heater On/Off etc.
• 24/48/ 96 & 192 TRAYS TRAY DRIER SUPPLIED WITH HEAVY DUTY (16 swg.) S.S. LM-304 PIPE TROLLEYs BUT WITHOUT TRAYS.
• Unit works on EITHER 230 V AC, 50 Hz. OR 440 V AC 3 Phase Supply.

• Single body made of heavy gauge S.S. LM-304 grade buffed & polished to mirror finish.
• Lid made of thick S.S. with argon-welded joints.
• Pressure upto 22 PSI factory set at 15 PSI.
• Complete with pressure gauge, safety valve, and steam release valve.
• Unit works on 230 V Ac, 50 Hz. Supply.

• Digital Temperature Indicating Controller with suitable sensor Factory set at 121oc [ 15 PSI ]
• Perforated Basket made of S.S. LM-304 grade

• Double body construction, single chamber for steam and water, covered externally by outer shell.
• Lid made of thick stainless steel, pressure upto 22 PSI factory set at 15 PSI.
• Complete unit with automatic air purging, Digital Temperature control & Indication with 0.1c Accuracy/ Resolution, with electronic Digital timer range 0 to 99 min.
• Autoclaving time cycle automatically starts when set pressure is achieved.
• Automatic steam release once autoclaving cycle complete.
• Complete with pressure gauge, safety valve, steam release valve, extra safety valve.
• Incorporated with an Automatic Pressure Control Switch as an additional safety device.
• Low Water level cut-off : Low water level cut-off assembly connected to heater which automatically cuts off power to heater if water level is not sufficient thus eliminating heater burn outs.
• Foot lifting arrangement included for Capacity 125 Ltr. and above. Not included/required for lower sizes.
• Provided withS.S. L-304 gradeperforated basket.
• Unit works on 230 V Ac, 50 Hz.

Description : Double body construction, single chamber for steam and water, covered externally by outer shell. Lid made of thick stainless steel, pressure upto 22 PSI factory set at 15 PSI. Complete unit with automatic air purging, Digital Temperature control & Indication with 0.1c Accuracy/ Resolution, with electronic Digital timer range 0 to 99 min. Autoclaving time cycle automatically starts when set pressure is achieved. Automatic steam release once autoclaving cycle complete. Complete with pressure gauge, safety valve, steam release valve, extra safety valve. Incorporated with an Automatic Pressure Control Switch as an additional safety device. Low Water level cut-off : Low water level cut-off assembly connected to heater which automatically cuts off power to heater if water level is not sufficient thus eliminating heater burn outs. Foot lifting arrangement included for Capacity 125 Ltr. and above. Not included/required for lower sizes. Provided withS.S. L-304 gradeperforated basket. Unit works on []

• Triple walled in construction.
• Exterior made of Mild Steel [ 18 swg. ] constructed on thick iron angle framework. The entire outer body is duly painted by long lasting DUCO Paint.
• Pre-heating Chamber made of Mild Steel [ 20 swg. ] & Inner Chamber made of Stainless Steel [18 swg.]
• Gap between the walls filled with initial layer of Asbestos Sheets followed by a dense layer of high quality low thermal mass glass wool insulation.
• Provision for forced air circulation using motorized blower.
• Provided with control panel for monitoring temperature.
• Installed with a Microprocessor based PID Digital Temperature Indicating Controller with BUILTIN Timer
• DIGITAL HIGH TEMPERATURE SAFETY CUT-OFF INCORPORATED WITHIN THE UNIT.
• Superior quality contactor for cutting / restoring power to the heaters are incorporated.
• Doors provided with safety cut-out system disables the Motor & the Heaters when doors are opened in operational mode.
• Control panel with suitable neon lamps for indication of Mains On/Off. Heater On/Off etc.
• 24/48/ 96 & 192 TRAYS TRAY DRIER SUPPLIED WITH HEAVY DUTY (16 swg.) S.S. LM-304 PIPE TROLLEYs BUT WITHOUT TRAYS.
• Unit works on EITHER 230 V AC, 50 Hz. OR 440 V AC 3 Phase Supply.

• Double walled in construction.
• Heat treated toughened glass window provides clear viewing of samples.
• Maximum vacuum upto 760mm of mercury column.
• Silicon gasket and positive door latch assures tight seal at all vacuum levels.
• A vacuum type stop cock & vacuum gauge are fitted on the top.
• Installed with Digital Temperature Indicating Controller with a suitable sensor for precise temperature control.
• Unit works on 230 V AC, 50 Hz supply.

• Outer chamber made ofMild Steel [ 20 swg.]duly powder coated and inner chamber made ofStainless Steel LM-304 grade [ 22 swg.].
• DUAL DISPLAYDigital Temperature Indicating Controller[For Set and Process Value Indication]. The Controller also has aBUILTIN DIGITAL TIMER adjustable upto 999 hrs. to set the sterilization time cycle.
• Thermostatic High Temperature Safety cut off provided.
• Rod type Shelves provided are made ofStainless Steel

• TEMPERATURE RANGE: Ambient + 5c to + 250c

• TEMPERATURE ACCURACY: 1 c

• TEMPERATURE ACCURACY: 1 c

• Microprocessor based AUTO TUNING PIDDigital Temperature Indicating Controller for precise Temperature control with BUILTIN Digital Timer in lieu of standard Controller (FOR STANDARD MODELS ONLY)
• Microprocessor basedPROGRAMMABLE PIDController cum Indicator with Printer Interface to connect Dot Matrix Printer. Print interval programme can print Date, Time & Temperature with print interval settable between 1 to 99 minutes [ without Printer ]
• Same as above but with PC software & connectivity

• TRIPLE walled in construction.
• The Inner Chamber is wound by a layer of thick Mineral wool. Gap between the walls filled with initial layer of Asbestos sheet and dense second layer of high insulation low thermal mass Glass wool.
• DIGITAL HIGH TEMPERATURE SAFETY CUT-OFFINCORPORATED WITHIN THE UNIT.
• ISI Marked Air Heating Elements are provided on the side walls of the chamber.
• Superior quality contactor for cutting / restoring power to the heaters are incorporated.
• Doors provided with safety cut-out system disables the Motor & the Heaters when doors are opened in operational mode.
• Provided with heavy duty S.S. LM-304 ball cages for locking arrangement
• Provision for forced air circulation using motorized blower.
• Unit works on either 230 V AC, 50 Hz. 1 Phase Supply OR 440 V AC, 50 Hz. 3 Phase Supply.

• TEMPERATURE RANGE: Ambient + 5c to + 350c

• TEMPERATURE ACCURACY: 1 c

• TRIPLE walled in construction.
• The Inner Chamber is wound by a layer of thick Mineral wool. Gap between the walls filled with initial layer of Asbestos sheet and dense second layer of high insulation low thermal mass Glass wool.
• DIGITAL HIGH TEMPERATURE SAFETY CUT-OFFINCORPORATED WITHIN THE UNIT.
• ISI Marked Air Heating Elements are provided on the side walls of the chamber.
• Superior quality contactor for cutting / restoring power to the heaters are incorporated.
• Doors provided with safety cut-out system disables the Motor & the Heaters when doors are opened in operational mode.
• Provided with heavy duty S.S. LM-304 ball cages for locking arrangement
• Provision for forced air circulation using motorized blower.
• Unit works on either 230 V AC, 50 Hz. 1 Phase Supply OR 440 V AC, 50 Hz. 3 Phase Supply.

• Exterior made of Mild Steel [ 20 swg. ] constructed on thick iron angle framework.
• Pre-heating chamber & Outer chamber made ofMild Steel [ 20 swg.]duly powder coated and inner chamber made ofStainless Steel LM-304 grade [ 18 swg.].
• Microprocessor based AUTO TUNING PIDDigital Temperature Indicating Controllerwith built in Timer upto 999 hrs.to set the sterilization time cycle.
• DIGITAL High Temperature Safety cut off provided.
• Rod type Shelves provided are made ofStainless Steel

• TEMPERATURE RANGE: Ambient + 5c to + 350c

• TEMPERATURE ACCURACY: 1 c

• TEMPERATURE ACCURACY: 0.5 c

• Microprocessor based AUTO TUNING PIDDigital Temperature Indicating Controller for precise Temperature control with BUILTIN Digital Timer in lieu of standard Controller (FOR STANDARD MODELS ONLY)
• Microprocessor basedPROGRAMMABLE PIDController cum Indicator with Printer Interface to connect Dot Matrix Printer. Print interval programme can print Date, Time & Temperature with print interval settable between 1 to 99 minutes [ without Printer ]
• Same as above but with PC software & connectivity

• Triple walled in construction.
• Exterior made of Mild Steel [ 18 swg. ] constructed on thick iron angle framework. The entire outer body is duly painted by long lasting DUCO Paint.
• Pre-heating Chamber made of Mild Steel [ 20 swg. ] & Inner Chamber made of Stainless Steel [18 swg.]
• Gap between the walls filled with initial layer of Asbestos Sheets followed by a dense layer of high quality low thermal mass glass wool insulation.
• Provision for forced air circulation using motorized blower.
• Provided with control panel for monitoring temperature.
• Installed with a Microprocessor based PID Digital Temperature Indicating Controller with BUILTIN Timer
• DIGITAL HIGH TEMPERATURE SAFETY CUT-OFF INCORPORATED WITHIN THE UNIT.
• Superior quality contactor for cutting / restoring power to the heaters are incorporated.
• Doors provided with safety cut-out system disables the Motor & the Heaters when doors are opened in operational mode.
• Control panel with suitable neon lamps for indication of Mains On/Off. Heater On/Off etc.
• 24/48/ 96 & 192 TRAYS TRAY DRIER SUPPLIED WITH HEAVY DUTY (16 swg.) S.S. LM-304 PIPE TROLLEYs BUT WITHOUT TRAYS.
• Unit works on EITHER 230 V AC, 50 Hz. OR 440 V AC 3 Phase Supply.

• TEMPERATURE RANGE: + 2c to + 8c

• TEMPERATURE ACCURACY: 0.5c

• TEMPERATURE UNIFORMITY: 1 c

• sOuter chamber made ofMild Steel [ 20 swg.]duly powder coated and inner chamber made ofStainless Steel LM-304 grade [ 20 swg.]Mirror finish.
• sMicroprocessor basedAUTO-TUNING PIDDigital Temperature Indicating Controller, Resolution 0.1c with suitable sensor. In the event of power failure, Non-Volatile memory allows chamber to return to original set point when power is restored.
• sThermostatic High Temperature Safety cut off provided.
• sRod type Shelves provided are made ofStainless Steel

• Microprocessor based PROGRAMMABLE PID Controller cum Indicator with Printer Interface to connect Dot Matrix Printer. Print interval programme can print Date, Time & Temperature with print interval settable between 1 to 99 minutes[ without Printer ]
• Same as above but with PC software & connectivity