Hebei Zengshan Intelligent Science and Technology Co.,Ltd

Diglipur, Andaman, Andaman & Nicobar Islands

Our factory(Hebei Zengshan Intelligent Science and Technology Co., Ltd) has improved and developed on the basis of the original cone paper tube machine. Now we have developed a new double-head cone paper tube machine. This machine draws on foreign advanced technologies such as Germany and South Korea, and uses high-quality accessories such as Japan NSK bearing, Taiwan Delta PLC, Taiwan Delta servo motor, Taiwan Adak cylinder, Delixi electric appliance, Taiwan deceleration motor, etc. It has realized the production of high-quality cone paper tubes by using new technologies and new processes of mechatronics. The total power of the whole machine is 45KW, the operating power is 23KW, the whole machine is 14m long, 7m wide and 3.6m high. 110 conical paper tubes can be produced per minute. According to the calculation of the conventional 5 57' paper tube, the original required paper width (640 mm 2) is 1280 mm, and the current paper width is 1170mm, which saves 110mm of paper and greatly reduces the cost of paper tube.

ZSZ-2018 automatic cone tube production line

Product introduction

This machine need no manual operation form raw paper to paper tube product.The whole production process is controlled by PLC programming, mian engine transmission uses can timing mechanism.All bearings of the machine adopt Japanese NSK bearings.Each position takes double speed variable frequency control technology.Also the none mechanical abrasion photoelectric control, approaching control and pneumatic delay control, which realize the mechanical and electrical integration.Suitable for the production of conical tube with various specification.

Process

Pollinginternal and external printingedge grindingcuttingReelingDryingFinishingcutting V-shaped openingopening processing pressinggrindinggallingfinishing

fully automatic conical paper tube reeling machine

This machine is suitable for conical tubes of various specification.After hanging the paper roll, internal and external printing, edge grinding, cutting.reeling.head cutting, the semi-finished paper tube will be sent to the dryer.It takes double speed variable frequency control technology.The reeling speed will be adjusted automatically .The whole process is eased by connecting with the dryer.

Product paramenters

Varieties of bobbin :For conical tube with various taper and calibre

Speed:50-60pcs/min

Power:13.27KW

Size:6080mm*2240mm*1500mm

product introduction

this mac hine uses chain-type circulationdrying.aftersetting up the temperature, the heat can be controlled, maintained and adjusted freely, feetured low consumptionand highoutcome.papertube can be feed and collected automatically afterconnecting with other equipment.

product parameters

varieties of bobbin:for conical tubes with various taper and calibre

seed:25-60pcs/min

power:10.1-24.5kw

size:5620mmx1700mmx3800mm

.

this machine is designed to turn the semi-finished product into conical paper tube adter vcutting, grinding, pressing, reversing and galling.

the speed can be adjusted freely with over-load protector and automatic stopping equipment when the improper operation happens to guarantee the safety and stability and lower the waste rate.the after finishing machine can also be used individually.

product parameters

varieties of bobbin:for conical tubes with various taper

air pressure:0.3-0.4mpa

speed:35-50pcs/min

operator:1

size:2600*1600*1580

.

ZSZ-2018 automatic conical paper tube after finishing machine

This machine is designed to turn the semi-finished product into conical paper tube after V cutting, grinding, pressing, reversing and galling.

The speed can be abjusted freely with cverload protector and automatic stopping equipment when the improper operation happens to guarantee the safety and stability and lower the waste rate. The after finishing machine can also be used individually.

Product parameters

Varieties of bobbin:For conical tubes with various taper

Air perssure:0.3-0.4mpa

Speed:35-50pcs/min

Operator:1

Size:2600*1600*1580

the automatic control temperature zsz-2018 of drying oven adopts the drying cycle circuit. once the temperature is determined, it can be adjusted freely, with low consumption and high performance. the paper cartridge can be a power supply and automatically assembled to connect to another device.main options:speed: 48 / minefficiency: 10.1-24.5kwexternal dimension: 5620mm-1700mm * 3800mm

Productintroduction

QGJ-98automatic precise cutter:QGJ-98automatic precise cutters function is to cut thesemi-finished product into the required length ofchemical fibre tube and air spinningtube.Themac hinehas pneumatic control which makes it easy toadjust.Suitablefor various specification of air-spinning tubeand short tube.

CQD-2000 Automatic head and corner cutting flocking machine

CQZ-2000 is a multi-function, automatic machine.Main funictions include :reversing, cutting edge, V-opening cut, flocking, colouring and drying.Also can do auto feeding, auto flock collecting, featured low dust pollution, low labour and high effciency.One of the most advanced flocking machine so far.

ZSZ-2018 automatic conical paper tube production line need no manual operation from raw paper to paper tube product. The whole production process is controlled by PLC programming, main engine transmission uses cam timing mechanism. All bearings of the machine adopt Japanese NSK bearings. Each position takes double speed variable frequency control technology. Also the none mechanical abrasion photoelectric control, approaching control and pneumatic delay control, which realize the mechanical and electrical integration. Suitable for the production of conical tube with various specification.


Process:
Rolling---internal and external printing---edge grinding---cutting---Reeling---Drying---Finishing---cutting V-shaped opening---opening processing---pressing---grinding---galling---finishing

Main Parameter:Power:49.2KWSpeed:48pcs/minSize:14000mm*6000mm*3800mmOperator:1

JXA-25A Cutter

JXA-25A is the professional cutter for manufacturing conical tubes.Fully-steel structure, mechanical power transmission brings high pressure.The maximnm load is 100 pieces.The machine has wide adjustable range, easy operation for clutch, will be safe and reliable.