Heat Treatment Sales & Services

Odhav, Ahmedabad, Gujarat

Principal :

Rockwell, Rockwell superficial & Rockwell cum Brinell tests consists of forcing an indentor (Diamond or Ball) into the surface of a test piece in two steps i.e. first with preliminary test force and thereafter with additional test force and then measuring depth of indentation after removal of additional test force (Remaining preliminary test force active) for measurement of hardness value.

RASNE series machines are suitable for Rockwell, Rockwell superficial & Rockwell cum Brinell tests. These are motorized digital Hardness testers having LCD display for easy hardness measurement. The results are displayed in 0.1 Rockwell unit for more accurate measurement.

Operation :

Various parameters of test can be set on front panel by operation of key board and observing LCD display Viz high/low limits, dwell time, auto/manual start, printer selection, scale selection etc. All set data can be verified edited by pressing SCL key one after another.

Machine operation is very simple. The normal mode is a bar followed by "SET" indication. Raise elevating screw slowly through bar indication till "SET" position which will show "PRESS START" indication. Now press "START" button. Loading/unloading cycle will be completed and hardness is shown on LCD display with High/Good/Low indication. Lower down elevating screw. Panel will show normal mode for next test. Also when required 'AUTO START' on front panel by operation of key board & observing LCD Display then raise elevating screw slowly through bar indication till "SET" position then it will starts loading/unloading cycle automatically & hardness is shown on LCD Display with High/Good/Low indication. 

FIE's new 'RASNE' series of Hardness Testing Machines come with much improved design & look with following major design changes.

• This is motorized machine having automatic loading/unloading cycle suitable for production testing.
• The machine body is having a taper front look and a large size read-out in the front. The machine is powder coated for better look. The paint shade do not fade and machine  looks like new over year.
• The elevating screw of machine is guided in a hardened and ground bush, not allowing movement of elevating screw more than 0.05 mm when raised to full height. The accessory is retained for years together due to hardened bush. 
• A hardened and ground stepped bush is fixed on top of main screw for location and rest surface. This guarantees no change in results due to rough handling of test table or test piece. It means a trouble free long life machine accuracy.
• An antifriction linear bearing with almost no clearance is provided for a perfect vertical movement of loading plunger with minimum friction. This enables testing of small dia. Pin or ball upto 3 mm dia.
• These models are provided with automatic working cycle and digital LCD display with 0.1 Rockwell resolution. This insures productivity with better accuracy.
• IS:1586:2000 for Rockwell and superficial test. IS:2281:2005 for Brinell Hardness Test. 

Note : For Brinell scale - manually select (187.5 or 250 kgf) with respected ball indentor. At that time take reference of set point only. Apply the load, then measure the impression dia by Brinell microscope only. (No Brinell scale display on screen).

Optional Accessories :

• Steel ball indentor 1/8", 1/4", 1/2".
• Testing Table 20mm dia.
• Testing Table 70mm dia. with 'V' groove for round jobs 10 to 80mm dia.
• Vari-rest to support add shaped jobs.
• Jominy test fixture for end quench test.
• Gooseneck Adoptor No.1.
• Special diamond indentor suitable for Gooseneck Adoptor No.1.
• Short nib diamond indentor suitable for Goodseneck Adoptor No.1.
• Gooseneck Adoptor No.2. 
• Special diamond indentor suitable for Goodseneck Adoptor No.2.
• Gooseneck Adoptor No.3.
• Raised center testing table 15mm dia.
• Diamond Spot Anvil.
• Cylindron anvil for testing big jobs above 20mm dia.
• Eyeball anvil with 25.4mm dia. or 38mm dia. ball.
• Gooseneck anvil for pipes 5 to 25mm ID with 5mm step inserts.
• Jack rest for long and heavy jobs. 

UCI hardness tester NOVOTEST T-U2 is designed for rapid non-destructive hardness testing of:

• Metals and alloys on standardized international scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV);
• Metals with distinctions in properties of steel (e.g., non-ferrous metals, alloys of iron and others.) and using five additional scales for calibration;
• using a scale of tensile strength (Rm) to determine the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale
• Ultrasonic hardness tester T-U2 implements the ultrasonic contact impedance method (UCI).

UCI method for the hardness testing

• The UCI hardness measuring method complies to ASTM A1038.
• The ultrasonic contact impedance (UCI) probe is purposed to be used for hardness measuring in the case of the testing area minimal thickness (from 1 mm), objects of complex surface shape, and for measuring surface hardened layers hardness.
• This method is very fast and easy: place the probe on the tested object surface, press the probe with the required effort to the surface and save the hardness value, shown on the display of the device. Small size diamond indenter allows measuring hardness value of all items, which are thicker than 1 mm. The UCI method of hardness testing is the least destructive because the hardness tester NOVOTEST T-UD2 with UCI probe leaves much smaller prints (imprints) than the majority of bench hardness tester would. That’s why a portable hardness tester with UCI probe is the best choice.
• The device has the main advantages of ultrasonic hardness tester and it is very usability and reliable.

Advantages

• Possibility of measuring the hardness value of products with any weights and thickness from 1 mm (small items, thin-walled structures, pipes, tanks, steel sheets, the products of complex shape, hardness control of metal coatings, etc.)
• Small mark on the surface of the tested product (user can test mirror surfaces, necks shafts, knives, gear teeth, etc.)
• Hardness testing the hardening layer of the surface
• Wide range of hardness measuring
• Usability of measuring
• Minimum number of controls
• Big graphic display with brightness backlighting
• Control the charge level of batteries
• Extended temperature range (frost protected, operating temperature up to -20^oC)
• Device has internal memory and allows user to connect with PC
• New, intuitive menu with tips on the buttons

Available Options

• Additional UCI probes. Also, after the purchase if will be needed, user can order the additional Leeb probe (D, DC, DL, C, D+15, E, G), with activation code and will get combined hardness tester with two probes (UCI+Leeb).
• Batteries
• Charger
• Hardness test blocks
• Portable grinding machine
• Case for hardness tester

Standard Package

• Electronic unit
• UCI probe (10N, 50N or 98N for choice)
• 2pcs batteries
• Charger
• Operating manual
• USB cable
• Case

Features :

• The independent research and development of lifting system and positioning system, ensured the accuracy and repeatedly of the testing process
• The optical system designed by senior optical engineer (who worked in the Shanghai Optics And Fine Mechanics Institute, Chinese Academy of Science) not only meet the definition of hardness testing requirements, but also can observe the micro structure of the material
• With Vickers hardness and Knoop hardness testing capabilities, and testing force can be extended to 2 KG
• Testing method, testing power and operation time can be displayed directly on the LCD screen
• The hardness value can be displayed directly by entering the indentation diagonal length and avoid the complication of the look-up table
• According to different visual habits of the operators, the strength of the light source can be adjusted. To avoid the visual fatigue for long time operation
• The testing data able to be printed directly by the built-in printer
• Reserved image channel can be connected with computer, used the image analysis software to analyzing the physical and chemical properties of the material

Standard Accessories : 1 piece: 10X micrometer eyepiece; 10X and 40X objective lens; Vickers indenter; X-Y Testing Table; Flat Fixture; Thin Fixture, Small Parts Fixture; Water level; Power cable; Dust cover; Instruction Book; Hardness Conversion Tables; Certificate of quality; Warranty Card; Accessory case; 2 pieces: Standard block of hardness; 4 pieces: horizontal adjusting screw

The Equotip Portable Hardness Tester is a versatile portable metal hardness tester offering extended capabilities and unmatched ease of operation. This Equotip Portable Hardness Tester has a large and clear display which is integrated in the robust ABS plastic housing together with the sealed membrane keypad. With variable background lightning, the LCD display of the Equotip Portable Hardness Tester offers a clear overview of the recorded metal hardness values even in dimly lit work areas. In particularly harsh working environments or for more comfortable handling the metal hardness tester Equotip Portable Hardness Tester can be stored in a protective bag. To date, Equotip Portable Hardness Tester is unmatched in its implementation of the portable metal hardness tester concept and has therefore become established as a globally recognized measuring technique. The Equotip Portable Hardness Tester meets the customers' needs for a non destructive metal hardness tester.

Features:

• Equotip Portable Hardness Tester is a hand-held metal hardness tester with a rugged shock-resistant housing and sealed membrane keypad.
• The metal hardness tester Equotip Portable Hardness Tester converts directly to all common hardness scales (HV, HB, HRC, HRB, HRA, HS, Rm); creates and uses another up to 20 customer-specific conversions for uncommon alloys Highly accurate ± 4 HL (0.5% at 800 HL) with automatic correction for impact direction.
• The Equotip Portable Hardness Tester metal hardness tester offers a wide measurement range Internal storage of 100’000 measured values in a flexible user-defined file/folder structure The metal hardness tester Equotip Portable Hardness Tester offers user profiles for a quick change of test setup (with password protection) Down-/upload data from/to PC via USB, Ethernet or RS-232 Proceq offers a unique variation of impact devices and support rings to serve most metal hardness test requirements. 

Applications :

Good for most metals Excellent for material selection, acceptance and production level testing The metal hardness tester Equotip Portable Hardness Tester is ideal for on-site testing of heavy and large components before and after installation Handy for difficult to access or confined metal hardness test locations The Equotip Portable Hardness Tester metal hardness tester is accurate also on curved test surfaces (R > 10 mm).

Standardization :

The following standards can be applied to the metal hardness tester Equotip Portable Hardness Tester: ASTM A956: DGZFP Guideline "Mobile Harteprufung" DIN 50156: VDI / VDE Guideline 2616 Paper 1.

Additional Information :

• Item Code - Equotip-3

The Cupping Testing Machine is a sheet & strip metal testing machine, for ferrous and non ferrous metals, with manual readout for Cupping, Deep Drawing & Deep Draw Bore Expanding Tests in accordance to corresponding national and international standards. The excellent functional layout of all the system functions makes the system user friendly. Operators without any previous knowledge and experience can be trained in few minutes for system operations.

Erichsen tester is designed to carry out Erichsen Cupping Test on metals. Quick clamping and manual operation facilitates faster and trouble free working of the machine.

Features :

• Fully Computerised (PC Based) Vickers Hardness Machine
• Direct and accurate measurement of Vickers Hardness number using "State of the Art" image processing technology
• Wide testing range: from soft metal up to hardest
• High accuracy and repeatability of measurement at all loads
• Faster measurement yielding to higher productivity
• Small size of indentation makes it a non destructive testing on finished components
• Motorised loading and unloading cycle
• Small loads allow testing of thin sheet metals
• Advanced Window XP based software
• User friendly software with Windows Features
• Online indentation setting and focusing on PC monitor
• Advance image processing: Algorithms implemented for precise calculation of hardness numbers with various options to cover all ranges of specimen
• Batch file Processing: Option for Data, storage and reports generation
• Statistical Evaluation: Software for calculating standard deviation, mean, medium, histogram
• Wide options in calibration mode
• Calibration / Verification on PC monitor makes easier to operate
• 'FIE' Computerised Hardness Tester is a simple and accurate means to produce automatically measure the diamond indentation to give Vickers hardness numbers
• These testers are suitable for measuring the hardness of precision metallic parts with wide testing range - from soft to hard and their accurate results are widely acclaimed. These testers strictly confirm to IS 1754 - 2002

 
Accessories :

• Standard Test Block
• Diamond Indentor
• Weights
• Flat Anvil
• Vee-type anvil ( Small & Big )
• Spanners
• Electric Cord & PC interface cord
• Video Capture
• Vickers software CD
• Instruction Manual

We offer Portable Surface Roughness Tester from Zeiss-TSK, packed with powerful functions for convenient operations.

All Functions for convenient Operations

• Complies with major International standards such as ISO, DIN, CNOMO, JIS, ASME.
• Data Memory/Battery Operation - Ten complete Data records can be stored.Rechargeable battery operation provides versatile usof the line independent of the line supply.
• Measuring in different positions - The small and light handysurf measures not only flat, horizontal, but also vertical and overhead surfaces.
• Direct data Transfer to the PC- The RS 232 serial interface is used to transfer measured data, parameters and profile curves directly to the PC.

Specifications

• Measuring Range - Z axis /- 160 um, X Axis 12.5 mm
• Resolution  - 0.01 um
• Standards - JIS 2001, JIS-1994, JIS 1982, ISO-1984, DIN-1990, ASME-1995, CNOMO
• Parameters - Pt, Ra, Rq, Rz, Rzmax, Rp, Rt, R3z, RSm, Pc, Rk, Rpk, Rvk, Mr1, Mr2, VO, K, Rmr, R, Rx, AR, W, Wx, AW, Wte
• Evaluation Curves - Section Profile Curve, Roughness Curve, ISO 13565

Additional Information:

• Item Code - Handysurf_E35

All Functions for convenient Operations :

• Complies with major International standards such as ISO, DIN, CNOMO, JIS, ASME
• Data Memory/Battery Operation: Ten complete Data records can be stored.Rechargeable battery operation provides versatile usof the line independent of the line supply.
• Measuring in different positions: The small and light handysurf measures not only flat, horizontal, but also vertical and overhead surfaces.
• Direct data Transfer to the PC- The RS 232 serial interface is used to transfer measured data, parameters and profile curves directly to the PC.

Features :

• Pocket size and economically price
• Large measuring range suitable for most materials
• Measures flat, outer cylinder and sloping surface
• Both Ra and Rz parameters in one instrument
• Features external calibration at keyboard
• Standard conform to ISO and DIN
• Rechargeable batteries, work while charging
• TR110 is equipped with Li-ion battery and backlight

Standard delivery :

• Main unit
• Protection cover for pickup
• Specimen Ra
• AC Charger
• TIME certificate
• Instruction manual
• Warranty card

The Ultrasonic Contact Impedance (UCI) probe is used for measuring the hardness value of small items, objects with a thin wall, complex form, and to measure the hardness of surface hardened layers.

Built-in camera allows user to take a picture of testing object and mark tested area with corresponding hardness value.

UCI Hardness Tester NOVOTEST T-U3 has the sealed housing with rubber protective strips, it is ideal for use in workshop and field conditions with high humidity, dust, etc. Hardness tester has frost-resistant display, which allows user to use the device at any season and in any climatic zone of the Earth.

The device has PC software with a comfortable and intuitive interface.

Advantage:

• Hardness measurement of any mass products with a thickness more than 1 mm
• Measuring the hardness of the surface hardened layer
• Small imprint after measuring (mirror surfaces of shafts necks, blades, gear teeth, etc.)
• Wide range of hardness testing
• Various measurement modes
• Calibration of any scale in any range
• Convenience and ease for measurement
• Optimized number of buttons
• Large full color graphic display with bright back-lighting
• Calibrations stored in memory of probe
• Extended temperature range (frost, down to – 40°C)
• Internal memory and communication with PC
• New, intuitive menu with tips on the buttons
• Optional wireless mini printer
• Water resistant case
• Has different operating modes:
• Graph – the mode of building of graph
• Histogram – the mode of building of histogram
• Statistics – the mode of statistic
• Smart – the mode of filtering of incorrect measurement

Additional Information:

• Item Code - T-U3
• Approx. Rs 1.30 Lakh / Piece(s)
• UCI Hardness Tester NOVOTEST T-U3

Principal :

Rockwell & Rockwell Superficial tests consists of forcing an indentor (Diamond or Ball) into the surface of a test piece in two steps i.e. first with preliminary test force and thereafter with additional test force and then measuring depth of indentation after removal of additional test force (Remaining preliminary test force active) for measurement of hardness value.Brinell test consists of forcing a hardened ball into surface of a test piece with a specified test-force and measuring the diameter of indentation for evaluation of Brinell hardness number.

Operation : For Rockwell & Rockwell Superficial Test

In case of 'RASN' series machines for Rockwell & Rockwell superficial tests a preliminary test force in first applied and then indicator is automatically set for zero. Quickly thereafter an additional test force is applied without removing the preliminary test force. When the penetration is stabilised, the additional test force is removed and the hardness number is shown directly on the indicator.

For Brinell Test : 

The operation is exactly same as above. However, the diameter of impression is measured outside of machine by Brinell microscope. Brinell hardness number is found out by referring corresponding hardness tables showing hardness number against dia. of indentation for specified ball diameter and test force.

Specification:

• Suitable for Rockwell Tests.
• Motorised for automatic Operation cycle i.e. load/dwell/unload.
• Preliminary Test Force - 98.07N (10kgf).
• Additional Test Force - 490.3, 882.6, 1373N, (50, 90, 140 kgf).
• Total Test Force - 588.4, 980.7, 1471N, (60, 100, 150 kgf).
• Test Force Selection by external dialing.
• Auto zero setting dial gauge.

'FIE' new 'RASN' series of Hardness Testing Machines come with much improved design and look with following major design changes.

• The machine body is having a taper front look and a big size dial gauge in the front. The machine is powder coated for far better look. The paint shade do not fade and machine looks like new over year.
• The elevating screw of machine is guided in a hardened and ground bush, not allowing movement of elevating screw more than 0.05 mm when raised to full height. The accessory is returned for years together due to hardened bush.
• A hardened and ground stepped bush is fixed on top of main screw for location and rest surface. This guarantees no change in results due to rough handling of test table or test piece. It means a trouble free long life machine accuracy.
• An antifriction linear bearing with almost no clearance is provided for a perfect vertical movement of loading plunger with minimum friction. This enable testing of small dia. pin or ball upto 3 mm dia.
• All machine models are provided with automatic zero setting dial gauge or digital readout. Hence zero setting at every test is avoided.
• Our Hardness Tester confirm to respective standard as under. IS : 2281, BS 10003-2 & ASTM E-10 for Brinell Test.

Additional Information:

• Item Code - RASN-M

Principal : Rockwell & Rockwell Superficial tests consists of forcing an indentor (Diamond or Ball) into the surface of a test piece in two steps i.e. first with preliminary test force and thereafter with additional test force and then measuring depth of indentation after removal of additional test force (Remaining preliminary test force active) for measurement of hardness value.Brinell test consists of forcing a hardened ball into surface of a test piece with a specified test-force and measuring the diameter of indentation for evaluation of Brinell hardness number.

Operation : For Rockwell & Rockwell Superficial Test In case of 'RASN' series machines for Rockwell & Rockwell superficial tests a preliminary test force in first applied and then indicator is automatically set for zero. Quickly thereafter an additional test force is applied without removing the preliminary test force. When the penetration is stabilised, the additional test force is removed and the hardness number is shown directly on the indicator.

For Brinell Test : The operation is exactly same as above. However, the diameter of impression is measured outside of machine by Brinell microscope. Brinell hardness number is found out by referring corresponding hardness tables showing hardness number against dia. of indentation for specified ball diameter and test force.

'FIE' new 'RASN' series of Hardness Testing Machines come with much improved design and look with following major design changes. :

• The machine body is having a taper front look and a big size dial gauge in the front. The machine is powder coated for far better look. The paint shade do not fade and machine looks like new over year.
• The elevating screw of machine is guided in a hardened and ground bush, not allowing movement of elevating screw more than 0.05 mm when raised to full height. The accessory is returned for years together due to hardened bush.
• A hardened and ground stepped bush is fixed on top of main screw for location and rest surface. This guarantees no change in results due to rough handling of test table or test piece. It means a trouble free long life machine accuracy.
• An antifriction linear bearing with almost no clearance is provided for a perfect vertical movement of loading plunger with minimum friction. This enable testing of small dia. pin or ball upto 3 mm dia.
• All machine models are provided with automatic zero setting dial gauge or digital readout. Hence zero setting at every test is avoided.
• Our Hardness Tester confirm to respective standard as under. IS : 2281, BS 10003-2 & ASTM E-10 for Brinell Test.

Model : RASN

• Suitable for Rockwell Tests.
• Manually Operated.
• Preliminary Test Force - 98.07 N (10kgf).
• Additional Test Force - 490.3, 882.6, 1373N (50.90, 140 kgf).
• Total Test Force - 588.4, 980.7, 1471N (60, 100, 150 kgf).
• Test Force Selection by external dialing.
• Auto zero setting dial gauge.

Rockwell cum Brinell Tester, Model RASN (B).

• Same as RASN above in additional
• Additional Test Force - 1471, 2354N (177.5, 240 kgf).
• Total Test Force - 1839, 2452N (187.5, 250 kgf).

'FIE' new 'RASN' series of Hardness Testing Machines come with much improved design and look with following major design changes.

• The machine body is having a taper front look and a big size dial gauge in the front. The machine is powder coated for far better look. The paint shade do not fade and machine looks like new over year.
• The elevating screw of machine is guided in a hardened and ground bush, not allowing movement of elevating screw more than 0.05 mm when raised to full height. The accessory is returned for years together due to hardened bush.
• A hardened and ground stepped bush is fixed on top of main screw for location and rest surface. This guarantees no change in results due to rough handling of test table or test piece. It means a trouble free long life machine accuracy.
• An antifriction linear bearing with almost no clearance is provided for a perfect vertical movement of loading plunger with minimum friction. This enable testing of small dia. pin or ball upto 3 mm dia.
• All machine models are provided with automatic zero setting dial gauge or digital readout. Hence zero setting at every test is avoided.
• Our Hardness Tester confirm to respective standard as under. IS : 3804, BS 10109-2 & ASTM E-18 for Rockwell Test.

Additional Information:

• Item Code - RAS-N

Rockwell System Hardness Tester :

• Model - RASN
• Suitable for Rockwell Tests.
• Manually Operated.
• Preliminary Test Force - 98.07 N (10kgf).
• Additional Test Force - 490.3, 882.6, 1373N (50.90, 140 kgf).
• Total Test Force - 588.4, 980.7, 1471N (60, 100, 150 kgf).
• Test Force Selection by external dialing.
• Auto zero setting dial gauge.

Rockwell cum Brinell Tester, Model RASN (B) :

• Same as RASN above in additional
• Additional Test Force - 1471, 2354N (177.5, 240 kgf)
• Total Test Force - 1839, 2452N (187.5, 250 kgf)

'FIE' new 'RASN' series of Hardness Testing Machines come with much improved design and look with following major design changes :

• The machine body is having a taper front look and a big size dial gauge in the front. The machine is powder coated for far better look. The paint shade do not fade and machine looks like new over year.
• The elevating screw of machine is guided in a hardened and ground bush, not allowing movement of elevating screw more than 0.05 mm when raised to full height. The accessory is returned for years together due to hardened bush.
• A hardened and ground stepped bush is fixed on top of main screw for location and rest surface. This guarantees no change in results due to rough handling of test table or test piece. It means a trouble free long life machine accuracy.
• An antifriction linear bearing with almost no clearance is provided for a perfect vertical movement of loading plunger with minimum friction. This enable testing of small dia. pin or ball upto 3 mm dia.
• All machine models are provided with automatic zero setting dial gauge or digital readout. Hence zero setting at every test is avoided.
• Our Hardness Tester confirm to respective standard as under. IS : 3804, BS 10109-2 & ASTM E-18 for Rockwell Test.

Model : RASN ( T )

• Suitable for Rockwell & Rockwell Superficial Tests.
• Manually Operated.
• Preliminary Test Force - 29.42, 98.07N (3, 10kgf).
• Additional Test Force - 177.7, 264.8, 411.9, 490.3, 882.6, 1373N (12, 27, 42, 50, 90 & 140 kgf).
• Total Test Force - 147.1, 294.2, 441.3, 588.4, 980.7, 1471N (15, 30, 45, 60, 100, 150 kgf).
• Test Force Selection by external dialing.
• Auto zero setting dial gauge.

'FIE' new 'RASN' series of Hardness Testing Machines come with much improved design and look with following major design changes.

• The machine body is having a taper front look and a big size dial gauge in the front. The machine is powder coated for far better look. The paint shade do not fade and machine looks like new over year.
• The elevating screw of machine is guided in a hardened and ground bush, not allowing movement of elevating screw more than 0.05 mm when raised to full height. The accessory is returned for years together due to hardened bush.
• A hardened and ground stepped bush is fixed on top of main screw for location and rest surface. This guarantees no change in results due to rough handling of test table or test piece. It means a trouble free long life machine accuracy.
• An antifriction linear bearing with almost no clearance is provided for a perfect vertical movement of loading plunger with minimum friction. This enable testing of small dia. pin or ball upto 3 mm dia.
• All machine models are provided with automatic zero setting dial gauge or digital readout. Hence zero setting at every test is avoided.
• Our Hardness Tester confirm to respective standard as under. IS : 5073, BS 10189-2 & ASTM E-18 for Rockwell Superficial Test.

Additional Information:

• Item Code - RASN-T

Rockwell Cum Rockwell Superficial Hardness Tester :

• Model - RASN ( T )
• Suitable for Rockwell & Rockwell Superficial Tests.
• Manually Operated.
• Preliminary Test Force - 29.42, 98.07N (3, 10kgf).
• Additional Test Force - 177.7, 264.8, 411.9, 490.3, 882.6, 1373N (12, 27, 42, 50, 90 & 140 kgf).
• Total Test Force - 147.1, 294.2, 441.3, 588.4, 980.7, 1471N (15, 30, 45, 60, 100, 150 kgf).
• Test Force Selection by external dialing.
• Auto zero setting dial gauge.

'FIE' new 'RASN' series of Hardness Testing Machines come with much improved design and look with following major design changes :

• The machine body is having a taper front look and a big size dial gauge in the front. The machine is powder coated for far better look. The paint shade do not fade and machine looks like new over year.
• The elevating screw of machine is guided in a hardened and ground bush, not allowing movement of elevating screw more than 0.05 mm when raised to full height. The accessory is returned for years together due to hardened bush.
• A hardened and ground stepped bush is fixed on top of main screw for location and rest surface. This guarantees no change in results due to rough handling of test table or test piece. It means a trouble free long life machine accuracy.
• An antifriction linear bearing with almost no clearance is provided for a perfect vertical movement of loading plunger with minimum friction. This enable testing of small dia. pin or ball upto 3 mm dia.
• All machine models are provided with automatic zero setting dial gauge or digital readout. Hence zero setting at every test is avoided.
• Our Hardness Tester confirm to respective standard as under. IS : 5073, BS 10189-2 & ASTM E-18 for Rockwell Superficial Test.

The device operates with both UCI (Ultrasonic Contact Impedance) and Leeb (dynamic) probes. User get the benefits of two methods of measurement – it is the maximum that can be obtained from portable hardness tester.

UCI method for the hardness testing: The ultrasonic contact impedance (UCI) probe is used for measuring the hardness of small items, objects with a thin wall, complex form, and to measure the hardness of surface hardened layers.

Leeb method for the hardness testing:

Leeb probe is used for measuring the hardness of non-ferrous metals, cast iron, coarse-grained materials, massive products etc.

Hardness tester allows user to measure the hardness at extremely low temperatures. The real tests has been carried out at a temperature of 25°C below zero. The device is operated very easy, the measurement accuracy did not exceed the value according to standards, keyboard and display of the device allowed user to operate confidently – the difference between the operating at the indoor temperature and operating at the extreme cold was not noticeable at all!

We have the CE certificate of conformity for Portable Combined Hardness Tester NOVOTEST T-UD3.

Advantages

• Small imprint after measuring (mirror surfaces of shafts necks, blades, gear teeth, etc.)
• Measuring the hardness of the surface hardened layer
• Wide range of hardness testing
• Various measurement modes
• 88 combinations of materials and hardness scales (calibrations)
• Calibration of any scale in any range
• Convenience and ease of measurement
• Optimized number of buttons
• Large full color graphic display with bright backlighting
• Photofixing of measuring samples
• Automatic recognition of probe
• Indication of the type of connected probe
• Calibrations stored in memory of UCI probe
• Extended temperature range (frost, down to – 40°C)
• Internal memory and communication with PC
• New intuitive menu with tips on the buttons
• Optional wireless mini printer
• Water resistant case
• Rubber bumper protected case
• Internal clock
• Measure hardness value of any mass products with a thickness more than 1 mm (small parts, thin-walled structures, pipes, tanks, steel sheets, articles of complex shape, hardness testing of metal coatings, etc.)

Specifications:

• UCI probe types - 1kgf (10N) 2.2 lbf, 5kgf (50N) 11lbf, 10kgf (98N) 22lbf
• Leeb probe types - D, DC, DL, C, D+15, E, G
• Measuring range - HV:230940; HRC:2070; HB:90650. Tensile strength, MPa 3701740
• Measuring accuracy - HV:±3%HV; HRC:±1.5%HRC; HB:±3%HB
• Indenter - Diamond indenter (UCI), Hardened ball (Leeb)
• Measuring direction Any direction 360°
• Data storage - Limited only by the memory card
• Hardness scale - RC, HB, HV, HRB, HS, HL, MPa
• Indication - Color LCD display (320×240)
• Operating environment Temperature:-20°C40°C; Humidity - 30%80%R.H.
• Power supply DC 4, 5V (3 pcs batteries AA)
• Instrument dimensions 160x75x30mm
• Battery life Approx. 10 hours

Additional Information:

• Item Code - T-UD3
• Approx. Rs 1.75 Lakh / Piece(s)
• Combined Hardness Tester NOVOTEST T-UD3

Rockwell and Digital Rockwell Hardness Tester consists of forcing an indentor (Diamond or Ball) into the surface of a test piece in two steps i.e. first with preliminary test force and thereafter with additional test force and then measuring depth of indentation after removal of additional test force (Remaining preliminary test force active) for measurement of hardness value. RASN-ET series machines are suitable for Rockwell and Rockwell superficial tests. These are motorized digital Hardness testers having LCD display for easy hardness measuring. The results are display in 0.1 Rockwell unit for more accurate measurement.

Operation:

• Various parameters of test can e set on front panel by operation of key board and observing LCD display Viz high / low limits, dwell time, auto / manual start, printer selection, scale selection etc. All set data can be verified / edited by pressing SCL key one after another
• Machine operation is very simple. The normal mode is a bar followed by "SET" indication. Raise elevating screw slowly through bar indicator till "SET" position which will show "PRESS START" indication. Now press "START" button. Loading / unloading cycle will be completed and hardness is shown on LCD display with High/ Good / Low indication. Lower down elevating screw. Panel will show normal mode for next test

Additional Information:

• Item Code - RASN-ET

Operation :

• Various parameters of test can e set on front panel by operation of key board and observing LCD display Viz high / low limits, dwell time, auto / manual start, printer selection, scale selection etc. All set data can be verified / edited by pressing SCL key one after another
• Machine operation is very simple. The normal mode is a bar followed by "SET" indication. Raise elevating screw slowly through bar indicator till "SET" position which will show "PRESS START" indication. Now press "START" button. Loading / unloading cycle will be completed and hardness is shown on LCD display with High/ Good / Low indication. Lower down elevating screw. Panel will show normal mode for next test

Model - TIME 5100 (TH 170) :

• The TIME 5100 (TH 170) is a portable hardness tester series which covers a wide range of testing. The TIME 5100 is for standard testing above 5mm, TIME 5102 (TH 172) for lighter or thinner material and the TIME 5104 (TH 174) for hard to reach locations. This range has been around the industry for 20 years and is a very reliable, quality build. It comes highly recommended.
• Tried and true, the TIME 5100 series is a portable hardness series of testers that are able to provide the results in applications where bench mount hardness testers can't be used. The TIME 5100 is powered by AA batteries, which is much more convenient than rechargeable battery units. TIME 5100 has onboard memory and the device has basic communication with your computer, using Windows HyperTerminal.
• The TIME 5100 series uses rebound technology and the result is measured in the LEEB Scale or HL. This is converted to the standard scales of Rockwell C, Rockwell B, Brinell, Vickers & MpA strength depending on the material and indenter used. The TIME 5100 provides accurate results and with the added versatility and portability.
• They have the ability to test on various Metals including Steel, Stainless steel, Aluminium, copper and other variations.

TIME 5100 (Standard) : The TIME 5100 (TH-170) has a D type impact device and is used for general purpose testing of samples greater than 5mm thickness. Using the LEEB rebound method the results can be displayed as Vickers, Brinell, Rockwell and Shore hardness values. These values can then be used for quality control and wear and tear analysis.

TIME 5102 (Thin material) : Should you need to test lighter or thinner samples then you may wish to consider the TIME 5102 (TH 172). The C-type impact device has a lighter impact force which allows if to test thinner samples and the result is measured in HLC rather than HLD. The TIME 5102 (TH-172) can test samples from 1mm provided they are coupled. If they are not coupled or stable and secure, the sample will retain energy or vibration from the impact of the indentor. This can result in a lower hardness reading. Please ensure that small or thin work pieces are coupled for an accurate result.

TIME 5104 (Needle Point for hard to reach Testing) :For hard to reach locations we recommend the TIME 5104 (TH-174). It comes with a needle point indenter so that is it perfect for deep crevices, and also for testing odd surfaces such as teeth on gears, o-ring grooves or any notched/stepped parts :

• Basic Kit Supply
• Portable Hardness tester
• Soft Carry Case
• Data Cable
• Software
• Cleaning Brush
• 2 x AA batteries
• Factory Calibration Certificate
• Complete Kit Supply
• All items in the Basic Kit
• Suitcase style aluminium hard shell, padded Carry Case
• Reference Test Block for self calibration of the Hardness Tester.

Please consider the importance of a Reference Test Block. During general testing, it is important to have a known reference value to compare against should you receive unexpected results.

Features :

• 2.4” color LCD display includes backlighting and over-size fonts
• Display direction can be changed to be read vertically or horizontally right and left-handed
• Color tolerance judgments, evaluation curves and all data can be displayed in one of 16 languages
• Self-timed measurement supported
• Security management supports password protected function locks
• A micro-SD card supports high-volume portable data storage - up to 10, 000 results can be stored
• Screen capture to memory card also supported
• Optional foot switch can be used for touch-free measurement
• Multiple output options include RS-232C and USB for maximum versatility Brochure.

Parameters : Rv, Rsk, Rku, Rc, RPc, RSm, Rmax, Rz1max, RzJIS, Rppi, RΔa, RΔq, Rlr, Rmr, Rδ, ς, HSC, Rpm, tp, Htp, Ra, Ry, Rz, Rq, S, Sm, Pc, R3z, mr, Rt, Rp, Rk, Rpk, Rvk, Mr1, Mr2, A1, A2, Vo ( customizable ) ( R, AR, Rx: M-type )

Features :

• Fully Computerised (PC Based) Vickers Hardness Machine.
• Direct and accurate measurement of Vickers Hardness number using "State of the Art" image processing technology.
• Wide testing range : from soft metal up to hardest.
• High accuracy and repeatability of measurement at all loads.
• Faster measurement yielding to higher productivity.
• Small size of indentation makes it a non destructive testing on finished components.
• Motorised loading and unloading cycle.
• Small loads allow testing of thin sheet metals.
• Advanced Window XP based software :

Latest GUI Features : 

• User friendly software with Windows Features.
• Online indentation setting and focusing on PC monitor.
• Advance image processing : Algorithms implemented for precise calculation of hardness numbers with various options to cover all ranges of specimen.

Batch file Processing : Option for Data, storage and reports generation.

Statistical Evaluation :

• Software forcalculating standard deviation, mean, medium, histogram etc. 
• Wide options in calibration mode.
• Calibration / Verification on PC monitor makes easier to operate. 

Specifications :

• 'FIE' Computerised Hardness Tester is a simple and accurate means to produce automatically measure the diamond indentation to give Vickers hardness numbers.
• These testers are suitable for measuring the hardness of precision metallic parts with wide testing range - from soft to hard and their accurate results are widely acclaimed. These testers strictly confirm to IS 1754 - 2002.

PC requirements :

• Intel Pentium IV 2.00 GHz or above processor is recommended.
• Microsoft Windows 98SE or above (Recommended XP)
• System Ram : 128 MB or above (Recommended 256 MB)
• One RS 232 (serial) port. (PC not included in standard scope of supply)

Construction :

• The robust machine frame is designed to accommodate the high precision loading.
• Specimen is placed on a testing table. The test cycle is fully automatic. The accurate load is applied on a diamond indentor by means of a lever and weights. After a specific lapse of a time the load is removed automatically. The image is digitized using a CCD camera fitted on the machine and is captured by PC. The diagonals of the indentation are automatically measured by PC to give the Vickers Hardness Number. 

Features :

• Fully Computerised (PC Based) Brinell Hardness Tester.
• Direct and accurate measurement of Brinell Hardness Number using "State of Art" image processing technology.
• 'Wide Testing Range' : from soft metal to medium hardness steels.
• High accuracy and repeatability of measurement at all loads.
• Faster measurement yielding to higher productivity.
• Hydraulic loading and unloading cycle.
• Advanced Window based software.

Latest GUI Features : 

User friendly software with all help file and Windows Features.

• Online indentation setting and focusing on PC monitor.
• Advance image processing : Algorithms implemented for precise calculation of hardness numbers with various options to cover all ranges of specimen.

Batch file Processing :

• Option for data/storage and reports generation.

Statistical Evaluation :

Software for calculating standard deviation, mode medium, histogram etc.

• Wide options in calibration mode.
• Extensibility for future advanced image processing analysis requirements.

'FIE' Computerised Brinell Hardness Tester, Model B 3000-PC is a simple and a accurate means to produce automatically measures the ball indentation to give Brinell hardness number.

These testers are suitable for measuring the hardness of metallic parts with wide leasting range - from soft to hard, and their accurate results are widely acclaimed.

These testers strictly confirm to IS:2281, BS:10003-2 and ASTM E-10.

Construction :

The robust machine frame is designed to accommodate the high precision loading system and an optical device with CCD camera. Specimen is placed on a testing table and brought in contact with clamping cone. Load/Unload/Read operations are done through a 3-position hand lever. The image is digitized using a CCD camera fitted on the optical device and is captured by the PC. The diameters of the indentation are directly measured by Pc to give the Brinell Hardness Number directly. 

Yamayo Bliss 'TH 170' is an advanced hardness tester distinguished by its high accuracy due to Lemo connectivity, wide measuring range and simplicity of operation. It is most suitable for testing of various kind of Metals.

Main Features

• Highly accurate (± 4HL @ 800 HL).
• Integrated display of results for all common hardness scales.
• Large, Clear & high contrast LCD for optimum viewing in all conditions.
• Easy calibration & Low Power consumption.
• Battery - 3 * 1.5v AAA no charging required
• Standardization - ASTM A956; DIN 50156.

Technical Specifications

• HL display range 170960 HLD
• Accuracy ± 4HLD
• Testing direction All direction
• Display 128X64 Dot matrix LCD display with back light
• Hardness scale HL, HRC, HRB, HV, HB, HS
• Std. Impact Device D, G, C, DC, E & DL
• Minimum job Weight 3.5 Kg.
• Min. job thickness 15mm (less then 5mm up to 3mm must be coupled)
• Dimensions 155mm x 68mm x 27mm
• Weight 220g (include impact device)

With Standard Accessories

• Main Display Unit TH – 170
• Impact Device ‘D’ (with Impact Body ‘D’ , Cable, Support Rings)
• Test block with HLD value
• Little Support Ring
• Charger
• Cleaning brush
• Calibration Certificate
• Instruction manual
• Carrying case

Optional Accessories

• Set of Support Rings (12 Pcs.)

Additional Information:

• Item Code - TH-170
• Minimum Order Quantity - 1 Set(s)
• Approx. Rs 33, 500 / Set(s)

YAMAYO BLISS 'TH 170' is an advanced hardness tester distinguished by its high accuracy due to Lemo connectivity, wide measuring range and simplicity of operation. It is most suitable for testing of various kind of Metals.

Main Features :

• Highly accurate (± 4HL @ 800 HL).
• Integrated display of results for all common hardness scales.
• Large, Clear & high contrast LCD for optimum viewing in all conditions.
• Easy calibration & Low Power consumption.
• Battery - 3 * 1.5v AAA no charging required
• Standardization - ASTM A956; DIN 50156.

With Standard Accessories :

• Main Display Unit TH – 170
• Impact Device ‘D’ (with Impact Body ‘D’ , Cable, Support Rings)
• Test block with HLD value
• Little Support Ring
• Charger
• Cleaning brush
• Calibration Certificate
• Instruction manual
• Carrying case

Optional Accessories : Set of Support Rings (12 Pcs.)

RAS :

We are among the top most Manufacturers and suppliers of Rockwell Hardness Tester. They provide the facility of Automatic load selection with automatic zero setting dial gauges. 

Technical Specifications :

• Loads 60, 100, 150 kgf
• Initial Load 10kgf
• Max. Test Height 230mm
• Depth of Throat 133mm
• Max. depth of
• elevating screw
• below base 240mm
• Size of base 170 x 430mm
• Machine Height 655mm
• Net Weight 65kg

Standard Accessories :

• Testing table 50mm dia 1 pc.
• Testing Table 38mm dia with 'V'
• groove for round jobs
• 6 to 45mm dia. 1 pc.
• Diamond Indenter 1 pc.
• Stell ball indenter 1/16" 1 pc.
• Test Block Rockwell 'C' 1 pc.
• Test Block Rockwell 'B' 1 pc.
• Test Block Rockwell Superficial 'N' NIL
• Allen Spanners 5 pcs
• Clamping Device 1 pc.
• Dash Pot Oil 1 Book
• Rubber bellow for elevating screw protection 1 pc.
• Instruction Manual 1 Book

Technical Specifications :

• Digital durometer for shore hardness testing pocket size
• Shore Hardness A
• DIN 53505, ASTM D2240, ISO 7619, JISK 7215
• Hardness Result, Average Value, Max. Value
• Hardness Range 0 - 100 HA
• Measurement Deviation < 1% H
• Resolution 0.1
• Auto switch off with RS232C interface
• Operating temperature 0 - 40°C
• Power supply 4 X 1.5V AAA (UM - 4) Battery
• Low Battery indicator
• Dimensions: 162 mm x 65 mm x 38 mm
• Weight 172 gm

Standard Delivery :

• Main Display unit
• Test Specimen
• Pocket case
• Certificate
• Instruction manual
• Carrying case

Basic machine design & operation similar to B-3000 (H). In addition ‘optical device’ with 14 x magnification provided in front to project dia of ball impression on glass screen with a micrometer measuring system with 0.01mm accuracy. The indentor swivels & projects dia of ball impression immediately after unloading operation which avoids additional time for measurement of ball impression

SAROJ Hardness Testers, Model B-3000 (H) & Model 3000 (O) are precision engineered confirming to IS : 22281 – 1968, BS : 240 and ASTM : E 10, however B-3000 (H) & B-3000 (O) are most suitable for production testing. These machines are designed to measure hardness of castings, forgings, other metals and alloys of all kinds, hard or soft, whether flat, round or irregular in shape. 

• Main Unit integrated withImpact DeviceDL
• Test block with HLD value
• Charger
• Cleaning brush
• Carrying suitcase
• Time certificate
• Instruction manual
• Warranty card
• Carrying case

Features :

• Testing range is very wide, from soft metal such as lead, upto the hardest, like hardeness steel.
• Same hardness number is obtained on the same specimen, regardless of the load applied.
• The indication is tiny and allows testing of a precision finished part.
• Loading and unloading cycle is motorised.
• Thin sheet metal is perfectly tested because the load applied is very small.
• Built-in projection screen to get accurate results.

Specifications :

• 'FIE' Vickers Hardness Tester is a simple and accurate means to produce and measure the diamond indentation.
• These testers are suitable for measuring the hardness of precision metallic parts with wide testing range from soft to hard and their accurate results are widely acclaimed. These testers strictly conform to IS : 1754 and ISO 6507-2.

Construction :

• The robust machine frame is designed to accommodate the high precision loading system and an optical projection screen.
• Specimen is placed on a testing table. The test cycle is fully automatic. The accurate load is applied on a diamond penetrator by means of a lever and weights. After a specific lapse of time, the load is removed automatically.
• The objective is indexed with the test piece and the diamond indentation is projected on the measuring screen.
• The diagonals of the indentation can be measured by means of the micrometer screw of the projection screen. 

 Machine designed with a hydraulic power pack and control circuit for effortless loading unloading operation. A dial gauge in front measure depth of ball penetration. This facilites production testing within tolerance limits by compression method.

SAROJ Hardness Testers, Model B-3000 (H) & Model 3000 (O) are precision engineered confirming to IS : 22281 – 1968, BS : 240 and ASTM : E 10, however B-3000 (H) & B-3000 (O) are most suitable for production testing. These machines are designed to measure hardness of castings, forgings, other metals and alloys of all kinds, hard or soft, whether flat, round or irregular in shape.