Geometric Steels Rollforming Pvt Ltd

Undri, Pune, Maharashtra

please check more details on websitehttps://www.metalslouver.com/

Double skin metal roof is a high-performance roofing system comprising of 2 metal roof sheets aligning parallel, One on top and the other at the bottom. The metal can be Steel, Aluminum, Colour Coated Galvnise, Galvalume, Colour Coated Galvalume.
The two metal sheets are fixed together with a Z Spacers creating a gap in the roof space for installation of insulation and barrier material, normally 48 density rock wool insulation is used in between two metal sheets its also called as sandwich panel. Double skin insulation is ideal solution to improve the indoor temperature, reducing exterior noise and fire protection of the entire system.
It has found its application largely in the power sector, auditorium, theaters, multiplexes and industrial and RCC Buildings. It is used both in roofing and wall Cladding.

Ladder Cable Tray

Single skin metal roof uses only 1 metal roof sheet and is designed to provide an economical solution, normally used in applications where performance demands are moderate. Insulation for single skin metal roof is installed below the metal roof sheet held by aluminum foil and steel wire mesh rolled over purlins. Geometric steels provide assembled under deck thermal insulation metal roofing sheets called Metahybrid

Rooflab Infra Pvt. Ltd. Are specialized in converting old RCC buildings that can be renovated using colour-coated profile sheets. As a result, it gets a good aesthetic look, and no periodic maintenance like painting, removing the algae formation, and deterioration of the building.

The Sag Rod is completely different from the Turnbuckle Rod or Clevis Rod. It usually requires Pass through of the members it supports like C or Z Purlins in 12mm to 16mm diameters Sag Rods as Lateral Supports for Girts and Purlins. Zsections Are commonly used as girts and purlins. In many Installations, sag rods are used to provide Alignment for these members for the attachment Of the steel panels and to reduce their tendency to Bend laterally and twist.

This pass through allows take-up to be achieved with standard nuts and washers. There is no need for left hand thread on either end. This Custom Component creates a sag rod between two girts. It also cuts holes in the two girts. There are two options to control the sizes of the nuts and washers. The first option sizes the nut and washer profiles based on the diameter of the rod diameter.

industrial louvers serve a critical need to allow air flow through openings in buildings while rejecting unwanted elements such as water and airborne debris. while the concept is simple, selecting the right product for the application is important to meeting performance needs louvers can also contribute to the aesthetic appeal of buildings by creating sight-proof screens to increase privacy, hide equipment or enclose parking facilities, selecting the right product for the application is important to meeting performance needs. regardless of the application, we geometric steel are happy to help create a design that will meet your specific needs. geometric steels louvers are made using alzn alloy steel sheet, colour coated alzn steel sheet and colour coated galvanized steel sheet. available in various colours to give aesthetic look to the building.

L Purlin

C Purlins are available in different sizes and material strength (Eg, 240 Mpa and 350 Mpa) to match the design computations of your building.

Purlins are perpendicular structural support member in slope of roof and cladding placed on principle rafter. These roof purlins are extensively used in large sized infrastructure project, factory, God owns.

C purlins are made from GI / CR / HR / GP / Quality Steel and is roll formed to required length with factory made punching to your specifications and requirement.

Geometric Steels manufactures a complete range of structural C and Z purlins and girts for industrial buildings, garages, warehouses, and PEB in pan anywhere strong, reliable steel framing is required. Manufactured from quality galvanized steel, this is a fully integrated system that allows for flexible design options. Supplied plain or punched, galvanized purlins, and manufactured from high-tensile steel for increased strength, reduced weight, and a long serviceable life.

Gutter system is one of the most crucial part of industrial roofing. If not done correctly in the first go. It will be a permanent headache for maintenance. Geometric Steels provides a variety of gutter systems as per requirement. We are the only company that can provide 5-meter length single length, length gutter of 0.50 mm to 3.00 mm thickness is this feature reduces 50% of laps and thus reduce the chances of leakage.

Geometric Steels manufactures a complete range of structural C and Z purlins and girts for industrial buildings, garages, warehouses, and PEB in pan anywhere strong, reliable steel framing is required. Manufactured from quality galvanized steel, this is a fully integrated system that allows for flexible design options. Supplied plain or punched, galvanized purlins, and manufactured from high-tensile steel for increased strength, reduced weight, and a long serviceable life.

METAhybrid Thermal Insulated metal roofing sheets consist of three kinds of different materials to give the product their own features and combined to make a new generation of heat insulation profile sheets

• A

  Top surface layer: Is profile metal sheet which provide strength and durability of steel, available in PPGI/GL/PPGL/AL in profile of 1135mm actual width and 1060mm cover width.

• B

  Intermediate Layer: Its special insulation material as per application in thickness of 6mm, 12mm, 19mm and 24 mm insulation.

• C

  Bottom lying layer: Its Aluminium foil Radiant Barriers

Gutter system is one of the most crucial part of Industrial Roofing. If not done correctly in the first go. It will be a permanent headache for maintenance. Rooflab Infra provides a variety of Gutter system as per requirement. Rooflab Infra is only company that can provide 5-meter single length, gutter in flexible material and design from point 0.50 mm to 3.00 mm thickness this feature reduce 50% of laps and thus reduce chances of leakage.