GARUD AUTOMATION Pune, Maharashtra

Bulk Material Handling Solutions at Low Costs Providing cutting edge solutions for bulk handling for all industries. If its achievable Garud Automation will find the solution best suited to your products or waste.

Over the years Garud Automation has design a variety of pallet handling conveyors for heavy duty  applications for more information on our pallet range please go to our dedicated page by clicking here

This is useful in heavy & light Industry. This is free tyoe conveyor to avide metal to metal contact.  Pu Roller Conveyor to use both side bearing for smooth working.  Width & sizes is depend on customer requirment.

We are instrumental in offering a comprehensive range of Degassing Units, which is a foundry treatment system, mainly used for the removal of hydrogen gas and non- metallic impurities from aluminum alloys. These units use inert gas that is delivered to the base of the melt via a uniquely designed spinning rotor. It is manufactured utilizing quality graphite and is designed to ensure maximum contact between metal and purge gas. The rotor of the unit produces a cloud of very small gas bubbles that effectively purge the melt, removing hydrogen and oxide inclusions as the gas rises to the surface. Moreover, the process is also designed to be non-turbulent so that the reintroduction of hydrogen and the regeneration of oxides are reduced to an absolute minimum. During the melting procedure, aluminum produces a lot of oxide and dross, when the mould is poured without removing the dross. The use of inert gas system in the complete process of degassing unit reduces the need for pollution control and gives improved working environment for the operators as well as eliminate toxic emissions & discharges to the surroundings.      Benefits   Environment friendly process due to use of inert gas systems Elimination of human error since process is automated Higher degassing efficiency (lower levels of gas in less treatment time) Consistently lower levels of gas content (reproducibility & repeatability of results) User friendly operations, easy replacements of graphite consumables Lowest gas levels attained Efficiency maintained through the life of the rotor Oxidation resistant, highest quality graphite to increase life Optimum bubble size and distribution Turbulence free Fast degassing    Precautions :   Power supply for DU should be 415V A.C. While replacing components the electrical supply should be disconnected fromthe 415 V supply outlet and the control panel MAIN switch should be in OFF position Metal should not be poured or drained out at any time unless water accumulation is removed The quality of inert gas used with the Degassing Units is the direct responsibility of the user All personnel in the vicinity of molten metal must wear proper face and eye protection, heat protection and body protection Accumulation of water anywhere near the vicinity of molten aluminum creates an explosion Use hand gloves for any activity near the hot degassing shaft & rotor to avoid severe burns

  Vacuum Pressure Test OR Aluminium Porosity Test ( Vacuum Testing Units ) In Quality management of Aluminium Alloy Casting, porosity is a major factor which is detrimental in terms of surface quality, corrosion resistance and mechanical properties. Hydrogen, which easily dissolves in molten aluminium which causes gas porosity. Vacuum Pressure Test is the most widely used technique in aluminum foundries. Vacuum pressure test is solidifying a sample of molten aluminium under reduced pressure (vacuum) up to 500mmHg. The reduced pressure enhances pore formation and pore expansion, giving out a visibly more porous sample than that solidified under atmospheric conditions. Porosity assessment is done in the following manner:     • Viewing the top of the sample. A puffed up surface indicates heavy gas content, where as a smooth & /    or a concave surface indicates mild or    acceptable gas content. • Cutting the sample & comparing the cut surface with a photographic standard.     Some of the features of our machine are:   Self sealing vacuum chamber. In-line suction filter for maintenance-free operation . Filter is designed for easy & fast cleaning. Vacuum display on the Vacuum pressure guage. Three phase unit with all protection. Has overload protection. Can be made mobile

We manufacture of different type of Hydraulic Press PLC Base & without PLC Base this is very simple & user friendly. As per coustamer requirment. Both hand safety push button are provided. This is useful for Bearing Pressing, Bush Pressing, Valve Seat & Valve Guide Pressing, Oil Seal Pressing, Cap Pressing, Shaft Pressing etc.