Garg Lab Solutions

Goregaon, Mumbai, Maharashtra

We are offering Process DescriptionHCL absorption columns are used for absorption of Hydrochloric gas, which statutorily are not permitted to vent into the atmosphere, and to produce the HCI acid. The column is constructed with a series of packed sections, a gas introduction point below that, a condenser on the top, and a cooler at the bottom. Make water is sprayed from the top and acid is collected from the bottom. HCL absorption columns are available in 80DN to 300DN diameter (for the gas rate 10 Kgshr to 300 Kgs hr approx).

We are offering The Falling Film Absorbers are typical Heat Exchangers with weir tube arrangement at the top - which is always vertically mounted. In Falling Film Absorbers gas to beabsorbed enters atthe top of FFA and flows co currently with absorbent liquid coming from storage tank by pump.Heat of solution released as a result of the absorption process is removed by the cooling water flowing in the shell - side of the falling film unit. Thus noxious gas absorption is effected at lower temperatures enablinga higher absorption rate than adiabatic absorption towers. The absorbed gas leaves at the bottom of FFA at a very low temperature for storage and disposal.The un - absorbed gas and any inert gases also leave via vent at the bottom of FFA and enter the venturi scrubber or bottom of tail gas tower scrubber as is shown in the figure. Falling film absorbers can be used for absorption of gases like HCl Cl2 So2 NOX HBr where higher efficiencies of absorption are required.

we are reckoned as reputed manufacturer, exporeter and supplier of bromine recovery plant in mumbai, maharashtra. our plant is known for its high effeciency and excellent performance. our recovery plant is manufactured using premium grade glass that ensures the best quality. the recovery plant is available with varied technical specifications to meet the varied requirements of buyers. our plant is corrosion and abrassion resistant. features : bromine recovery plant are available in 1 tpd / 2 tpd / 3 tpd etc. capacities. brief about product : bromine are being a highly reactive material, finds wide applications in many chemical industries like : organic intermediates, dyestuffs, agrochemicals, fire retardents etc.

Our organization is avidly engaged in supplying an exclusive range of Adiabatic Type HCL Gas Absorber at reasonable prices. Working in close coordination with the genuine logisticians, we dispatch the products in the dedicated time.

Process Description :

• HCL absorption columns are used for absorption of Hydrochloric gas, which statutorily are not permitted to vent into the atmosphere, and to produce the HCI acid.
• The column is constructed with a series of packed sections, a gas introduction point below that, a condenser on the top, and a cooler at the bottom. Make water is sprayed from the top and acid is collected from the bottom.
• HCL absorption columns are available in 80DN to 300DN diameter (for the gas rate 10 Kgshr to 300 Kgs hr approx).

The unit has been designed to suit the customers requirement of

combination of versatile reaction / distillation or combination for pilot plant

work.

This has a flexibility of working at atmospheric pressure as well as under

vacuum.

Typical unit has a reaction vessel fitted in a metal heating/cooling bath

having facility for heating and cooling bath by means of heating/cooling

Fluids as a media.

The Standard system is equipped with stirrer heaving mechanical seal, a

packed column on the side neck of the vessel, reflux divider, coil type

condenser and or receiver system having a product, cooler, vent, drain and

vacuum valves, Option of speed variation by machanical variator or

electronic variator can be provided.

Receiver system is equipped with product cooler. Vent / vaccum valve and

drain valve.

The above unit are available in 10 Ltr., 20 Ltr., 50Ltr., 100 Ltr., 200 Ltr. & 300Ltr

capacity with spherical reactor.

This Unit is Used for Carrying Out Reactions Under Stirred Condition and with Provision for Simple Reflux Distillation. the Reaction Vessel is Mounted in a Heating Bath and Fitted with Addition Vessel, Motor-driven Stirrer and Provision for Condensation with Refluxing. the Product is Sub-cooled and Collected in a Receiver. the Units are Available in Vessel Sizes of 20, 50, 100 & 200l and is Suitable for Operation Under Atmospheric Pressure and Full Vaccum.

Buyers are free to place orders and can expect timely deliveries of the same. As, our organizations is a suppliers of Fractional Distillation Unit on GLR; purchasers can place wholesale orders for it, and get them at the lowest prices.

A famed name, the company is entrusted with a task of making available high quality lot ofFractional Distillation Unit On Assemblyly. Our organization has worked diligently to create a well-organized supply network. Thus, patrons can order the goods in wholesale and expect timely arrival of consignments.

 

Technical Information :

• Lower than any other industrial glass
• Manufactured using the Borosilicate Glass 3.3
• Abbreviation for the coefficient of linear expansion - (3.3 ± 0.1) x 10-6 K-1
• Maximum working pressure for a given operating temperature is greater
• Since this glass expands less, the tensile stresses in the glass wall during heating are less High ability to thermal shock
• Special property of Borosilicate Glass 3.3, complemented by the use of other highly corrosion resistant materials such as PTFE and ceramics
• Sizes Available - DN25 to DN450 mm
• Raw Material Used - Borosilicate glass

Special Features :

• Excellent corrosion resistance to very large number of chemicals, unmatched by other material
• Smooth pore free surface
• Clear visibility

We are dedicatedly engaged in manufacturing, exporting, and supplying the premium quality Fractional Distillation Unit. In this assembly, the reboiler Fractional Distillation Unit comprises of a vessel that is placed on heating bath. The vapors can be refluxed whenever required. The Fractional Distillation Unit, we offer, is collected in the bottom that can be drained off through a drain valve. Technical Information :

• Lower than any other industrial glass
• Manufactured using the Borosilicate Glass 3.3
• Abbreviation for the coefficient of linear expansion: (3.3 0.1) x 10-6 K-1
• Maximum working pressure for a given operating temperature is greater
• Since this glass expands less, the tensile stresses in the glass wall during heating are less High ability to thermal shock
• Special property of Borosilicate Glass 3.3, complemented by the use of other highly corrosion resistant materials such as PTFE and ceramics
• Sizes Available : DN25 to DN450 mm Raw Material Used : Borosilicate glass Special Features :
  • Excellent corrosion resistance to very large number of chemicals, unmatched by other material
  • Smooth pore free surface
  • Clear visibility