Bus duct is used for the effective and efficient supply of electricity in mostly industrial locations.Copper or aluminumis used for the conductor of bus duct that be insulated and enclosed completely for protection against mechanical damage and dust accumulation. A bus duct system is an effective method of distributing power to your switchgear and various loads. However, bus duct problems can lead to catastrophic damage and extensive downtime.

There are basically three general categories of bus duct (all-metal enclosed). The nonsegregated phase bus implies a duct where allphase conductorsare in a common metal enclosure without barriers between phases. This definition applies to rigid and flexible conductors such as the bar or cable duct.

Segregated phase bus is a duct where phase conductors are in a common metal enclosure but are segregated by ground metal barriers between each phase conductor. Isolated phase duct is when each phase conductor is enclosed in its own metal housing and adjacent conductor housings are separated by an air space. This duct usually has higher amp ratings than other types. The housing and conductors are tubular in shape and are welded at site together. This duct is force-air cooled above a 25000A continuous rating.

Modular construction with either top or bottom cable entry. Single or double front. Up to 6000Amp.with Aluminum or Copper bus. Design compactable for 35KA/50KA & 65KA as per the requirement. Extensible at both ends. PLC interlocking for complicated schemes with double bus system.

We manufacture and export a qualitative range of thyristorised APFC panels, which are manufactured using best quality material. These panels are high speed power factor correcting system used for P.F. correction of loads with in short time. Easy to install, our range is available in both manual as well automatic functions. Further, we make sure that these are in strict adherence with set international standards.

We offer thyristorised APFC panels, which are designed using cutting edge technology. Our range is known for power quality improvement, safe usage and less maintenance cost. Quality tested on various measures, our panels are standard compliant and available at highly competitive prices.

Following are the prominent characteristics of thethyristor PFC modulesoffered by us:

• Suitable for real time power factor correction.
• Reaction time 5 mili seconds.
• Easy installation like contactor.
• Manual operation possible.
• Automatic Switch-off in case of over current & over temperature.

We manufacture and export Thyristorised APFC Panels for power factor correction and power filtration. The transmission effect created by electro-mechanical switched system is avoided by smooth connection and dis-connection of capacitors to and fro the network. The switches are resistant to wear and tear during the continuous process and thus capacitors remain safe. By taking into consideration advanced closed loop and measuring unit, the power factor is controlled very precisely. Reduction of over current protects the capacitors from exploding and thus resulting in longer life.

Our range of Power cum Motor Control Centre (PMCC) Panel is used to distribute the power through the panels. It is then distributed to the different motor loads located at various parts of the factory system. Further, it is transferred from one place through the motor starter fitted in the panel of required rating with full protection. Moreover, the motors can be started form remote positions as well. We also manufacture the Numerical / Electromechanical relay base MCC Panel.

We specialize in providing Programmable Logic Controller (PLC) Panels that are available in various specifications. It holds the capability to withstand extreme weather conditions and well known for its precise dimensions & efficient performance. Our range of Programmable Logic Controller (PLC) Panels is widely used for automation of electromechanical processes, which includes control of machinery on factory assembly lines, amusement rides and lighting fixtures.

Depend on the Client requirement; we suggest the Quality brands from the globe.

Also we provide an efficient after sales support through the strong network of engineers all over India and abroad also.

We also manufacture Soft Starter panels for various soft starters such as Siemens, ABB, L&T. We proudly present ourselves as one of the leading offerer of Soft Starter Panels. These Soft Starter Panels are made from excellent quality raw materials and these are widely appreciated by our customers for its quality. Our products can be customized as per customer's specifications. These Soft Starter Panels can be availed at most competitive price.

What is power Factor?

Power Factor (PF) is the ratio of Power Utilized (KW) and Power Drawn (KVA).

Generally, when the applied to the electrical motors, the entire power is not converted as useful Work Done (KW). Depending on inductance of the motor a reactive power (KVAR) is generated which results in drawing of excess KVA.

PF = KWH / KVAH

To reduce the KVA drawn, the inductive KVAR is to be nullified by introducing an equal and opposite Capacitive KVAR according to the load pattern, thus OPTIMUM PF is maintained.

Why Power Factor must be maintained?

By maintaining an optimum PF the Power drawn (KVA) can be reduced, thus reducing the current passing through the electrical circuits to the maximum extent possible (event up to 50%) thereby reducing the machine down time. reduction in heat losses in turn increases the life of the electrical circuits.

The State Electricity Boards (SEBs) has installed Digital Electronic Energy (Tri-Vector) Meters for consumers, which has the provision of showing the PF and insisting to maintain the average Power Factor above a Specified limit (0.85 0.90 PF)Otherwise, for every reduction of 0.01 from the specified PF, PENALTY is levied on the Energy Consumption Charges (KWh) on the Electricity Bill. SEBs are also offering PF incentives if the PF is maintained above the specified PF.

In few states, where the metering unit is KVAh and if the PF is maintained at its optimum of 0.99, the electricity bill amount itself is reduced considerably.

The optimum Power Factor can be maintained by installing Galaxy Electro Techs AUTOMATIC POWER FACTOR CONTROL PANEL

Salient Features of Galaxy Electro Techs APFC Panel:

• Adjustment to any step of capacitor value
• Micro controller based technology. Digital computation of various parameters
• Continuous monitoring of parameters like Line Voltage, Current, Active, reactive and Apparent Powers and energies
• Scrolling Display on a Dot Matrix LCD
• Protection of Capacitors against damage due to High Voltage, Low Voltage
• Tends to maintain 0.99 lag
• Plug-in terminal connection
• No-Volt release features to disconnect all capacitors in the event of power failure
• Dynamic control of Reactive Power and Power Factor
• RS 232 / RS 485 Standard output port (optional)
• Fine & Coarse correction Controller

Benefits of Galaxy Electro Techs APFC Panel:

• Power Factor penalty is avoided
• Avail incentives by maintaining optimum Power Factor
• Optimize the capacity by reducing the maximum demand KVA
• Avoids excess demand charges
• Improvement in line voltage
• Reduced line current losses and cable overheat
• Enhanced life of electrical circuits
• Avail Depreciation
• Reduced consumption (KWH) charges
• Avoids overloading of Distribution Transformers
• Additional Service connections in existing generation of power by reducing Energy Losses
• Reduced line losses Benefits SEBs and Nation
• Galaxy Electro Techs APFC Panels are available from 25KVAR 2500KVAR Model onwards

We offers PC & Aux. Control desk that are used to control various motors/gadgets on/off, remotely settled in any comfortable place and for monitoring. Panel is located inside the area and multi-core cable is used to interlink panel & desk. We also offer this panel for use of Rice meal or flour meal etc.

Bus duct is used for the effective and efficient supply of electricity in mostly industrial locations.Copper or aluminumis used for the conductor of bus duct that be insulated and enclosed completely for protection against mechanical damage and dust accumulation. A bus duct system is an effective method of distributing power to your switchgear and various loads. However, bus duct problems can lead to catastrophic damage and extensive downtime.

There are basically three general categories of bus duct (all-metal enclosed). The nonsegregated phase bus implies a duct where allphase conductorsare in a common metal enclosure without barriers between phases. This definition applies to rigid and flexible conductors such as the bar or cable duct.

Segregated phase bus is a duct where phase conductors are in a common metal enclosure but are segregated by ground metal barriers between each phase conductor. Isolated phase duct is when each phase conductor is enclosed in its own metal housing and adjacent conductor housings are separated by an air space. This duct usually has higher amp ratings than other types. The housing and conductors are tubular in shape and are welded at site together. This duct is force-air cooled above a 25000A continuous rating.

Modular construction with either top or bottom cable entry. Single or double front. Up to 6000Amp.with Aluminum or Copper bus. Design compactable for 35KA/50KA & 65KA as per the requirement. Extensible at both ends. PLC interlocking for complicated schemes with double bus system.

We manufacture and export a qualitative range of thyristorised APFC panels, which are manufactured using best quality material. These panels are high speed power factor correcting system used for P.F. correction of loads with in short time. Easy to install, our range is available in both manual as well automatic functions. Further, we make sure that these are in strict adherence with set international standards.

We offer thyristorised APFC panels, which are designed using cutting edge technology. Our range is known for power quality improvement, safe usage and less maintenance cost. Quality tested on various measures, our panels are standard compliant and available at highly competitive prices.

Following are the prominent characteristics of thethyristor PFC modulesoffered by us:

• Suitable for real time power factor correction.
• Reaction time 5 mili seconds.
• Easy installation like contactor.
• Manual operation possible.
• Automatic Switch-off in case of over current & over temperature.

We manufacture and export Thyristorised APFC Panels for power factor correction and power filtration. The transmission effect created by electro-mechanical switched system is avoided by smooth connection and dis-connection of capacitors to and fro the network. The switches are resistant to wear and tear during the continuous process and thus capacitors remain safe. By taking into consideration advanced closed loop and measuring unit, the power factor is controlled very precisely. Reduction of over current protects the capacitors from exploding and thus resulting in longer life.

Our range of Power cum Motor Control Centre (PMCC) Panel is used to distribute the power through the panels. It is then distributed to the different motor loads located at various parts of the factory system. Further, it is transferred from one place through the motor starter fitted in the panel of required rating with full protection. Moreover, the motors can be started form remote positions as well. We also manufacture the Numerical / Electromechanical relay base MCC Panel.

We specialize in providing Programmable Logic Controller (PLC) Panels that are available in various specifications. It holds the capability to withstand extreme weather conditions and well known for its precise dimensions & efficient performance. Our range of Programmable Logic Controller (PLC) Panels is widely used for automation of electromechanical processes, which includes control of machinery on factory assembly lines, amusement rides and lighting fixtures.

Depend on the Client requirement; we suggest the Quality brands from the globe.

Also we provide an efficient after sales support through the strong network of engineers all over India and abroad also.

We also manufacture Soft Starter panels for various soft starters such as Siemens, ABB, L&T. We proudly present ourselves as one of the leading offerer of Soft Starter Panels. These Soft Starter Panels are made from excellent quality raw materials and these are widely appreciated by our customers for its quality. Our products can be customized as per customer's specifications. These Soft Starter Panels can be availed at most competitive price.

What is power Factor?

Power Factor (PF) is the ratio of Power Utilized (KW) and Power Drawn (KVA).

Generally, when the applied to the electrical motors, the entire power is not converted as useful Work Done (KW). Depending on inductance of the motor a reactive power (KVAR) is generated which results in drawing of excess KVA.

PF = KWH / KVAH

To reduce the KVA drawn, the inductive KVAR is to be nullified by introducing an equal and opposite Capacitive KVAR according to the load pattern, thus OPTIMUM PF is maintained.

Why Power Factor must be maintained?

By maintaining an optimum PF the Power drawn (KVA) can be reduced, thus reducing the current passing through the electrical circuits to the maximum extent possible (event up to 50%) thereby reducing the machine down time. reduction in heat losses in turn increases the life of the electrical circuits.

The State Electricity Boards (SEBs) has installed Digital Electronic Energy (Tri-Vector) Meters for consumers, which has the provision of showing the PF and insisting to maintain the average Power Factor above a Specified limit (0.85 0.90 PF)Otherwise, for every reduction of 0.01 from the specified PF, PENALTY is levied on the Energy Consumption Charges (KWh) on the Electricity Bill. SEBs are also offering PF incentives if the PF is maintained above the specified PF.

In few states, where the metering unit is KVAh and if the PF is maintained at its optimum of 0.99, the electricity bill amount itself is reduced considerably.

The optimum Power Factor can be maintained by installing Galaxy Electro Techs AUTOMATIC POWER FACTOR CONTROL PANEL

Salient Features of Galaxy Electro Techs APFC Panel:

• Adjustment to any step of capacitor value
• Micro controller based technology. Digital computation of various parameters
• Continuous monitoring of parameters like Line Voltage, Current, Active, reactive and Apparent Powers and energies
• Scrolling Display on a Dot Matrix LCD
• Protection of Capacitors against damage due to High Voltage, Low Voltage
• Tends to maintain 0.99 lag
• Plug-in terminal connection
• No-Volt release features to disconnect all capacitors in the event of power failure
• Dynamic control of Reactive Power and Power Factor
• RS 232 / RS 485 Standard output port (optional)
• Fine & Coarse correction Controller

Benefits of Galaxy Electro Techs APFC Panel:

• Power Factor penalty is avoided
• Avail incentives by maintaining optimum Power Factor
• Optimize the capacity by reducing the maximum demand KVA
• Avoids excess demand charges
• Improvement in line voltage
• Reduced line current losses and cable overheat
• Enhanced life of electrical circuits
• Avail Depreciation
• Reduced consumption (KWH) charges
• Avoids overloading of Distribution Transformers
• Additional Service connections in existing generation of power by reducing Energy Losses
• Reduced line losses Benefits SEBs and Nation
• Galaxy Electro Techs APFC Panels are available from 25KVAR 2500KVAR Model onwards

We offers PC & Aux. Control desk that are used to control various motors/gadgets on/off, remotely settled in any comfortable place and for monitoring. Panel is located inside the area and multi-core cable is used to interlink panel & desk. We also offer this panel for use of Rice meal or flour meal etc.