Testing Equipment #358890

• rightness, & Opacity Tester (ISO) The instrument measures brightness, opacity and color by diffused reflectance according to relevant ISO standards. It gives an instantaneous digital readout, which shows the Brightness, Opacity, Rx, Ry, Rz and ERIC values of pulp, paper, paperboard, coating agents, filter , mineral and other similar materials. Made with imported opticals.

• Brightness, Opacity & Color Tester -ISO (Microprocessor based) The instrument measuring brightness, opacity and color by diffused reflectance according to relevant ISO standards. Gives out instantaneous digital read / printout, which compute worked out details such as CIE, Tri stimulus color, Rx, Ry, Rz, x, y, z, CIE Lab, Hunter Lab, ERIC values materials. It includes built-in/external Printer and different ranges of measurement routine. Made with imported Opticals.

ELECTRONIC MODELS :

• Electronic Tensile Tester (Vertical Model) with digital Display of Tensile strength & Stretch of paper, paperboard and similar materials. Complete with memory for retaining peak value, automatic or normal zero setting, overload and over travel protection facilities. With imported load cell & imported DC motor. Standard Model Range : 0-50 Kgf or 500 N & available in other load ranges 0-100 Kgf or 1000 N, 0-1000 Kgf or 10, 000 N.

• Electro-Mechanical - (Motorized Schopper Type) A reliable and cost effective model for providing the determination of tensile strength and elongation of paper, paperboard and other similar material. Pulling rate is regulated through DC variable speed drive during the test.Range 0-30 Kg. or 300 N.0-60 Kg. or 600 N.

• Electro-Hydraulic TypeGive the pulling clamp a uniform and vibration free movement regardless of the load. Hydraulic Oil pump specially designed, with a built-in variable constant speed has a silent running and a long service life with low maintenance cost.

For measuring the resistance against tearing of paper, board plastic films, foils and other similar materials. An initial cut is made in a set of test piece which are then torn through a given distance the work done in the test piece is measured as the loss in potential energy of a pendulum which is free to swing on it horizontal axis. A calibrated scale indicate the mean tearing force.

For determining the folding endurance of all kinds of paper, paperboard, foil & films with a standard folding speed per minute.

• Khler Molin Type with five figure digital impulse counter - Loading clamps of dead weight type, giving standard load of 800 gm, during test. With five figure impulse counter having hold and zero setting. For testing two strips at the same time, done in oscillating clamps, and the tension of the strips is effected by means of weights.

Option : Five digit counter based on microcontroller circuitry

• Schopper Type with five figure impulse counter - Motor driven, Self contained unit, suitable for paper & films upto 0.010" (0.25mm). Loading clamps of spring type giving standard load of 1000 gm during the test. With five figure digital impulse counter having hold and zero setting. Two horizontally opposed and movable clamping jaws, which holds specimen 100 mm (4") long under variable tension during the folding cycle.

• MIT Type A constant tension is applied to test specimen of width 15mm and the specimen is bent 135O each to the left and right. Tension is applied by means of spring. Rotation speed 175 cpm & 90 cpm.

Option for all models : Five digit counter based on microcontroller circuitry.

For evaluating stiffness and resillient qualities of paper, plastics, cardboard, light metallic sheets, foil and other flexible material having comparatively strong bending resistance. One end of the test piece is easily fastened into the clamp. The maximum force required to bend the test piece to a specified angle is presented on the graduated scale.

• Constant Speed Lab Crushing Tester - For determining the edgewise ring crush or flat crush resistance of corrugated board, paperboard, paper & plastics etc. Load range 0-50 Kg., 0-100 Kg.

• Electronic Lab Crush Tester - With digital readout : For accurate testing of paper, paperboard, solid fiberboard & corrugated board for RCT, ECT, CCT and FCT test and its components as well as performing compression test on all small packages. Accessories provided for RCT testing only, Load range : 0-50 and 0-500 Kg. (5000 N.)

Option for all models :

• Precision Test Strip Cutter Punch & Die Type - For preparation of test pieces towards use in Ring Crush Tests. Width 12.7 mm x 152 mm.
• Circular Cutter For Flat Crush Test - Cutting out circular sample of board and similar materials . One test specimen at a time for measurement of Flat Crush Test.
• Circular Neck Down Cutter - For preparation of test pieces for measurement of Edge Crush Test.
• Sample Cutter for Edge Crush Tester - Sample size width 25, 50 mm.
• Support block for Edge Crush Test
• Pin Adhesion Attachment - To measure glue strength

For evaluating stiffness and resillient qualities of paper, plastics, cardboard, light metallic sheets, foil and other flexible material having comparatively strong bending resistance. One end of the test piece is easily fastened into the clamp. The maximum force required to bend the test piece to a specified angle is presented on the graduated scale.

• Stiffness Tester (Taber Type) with triple shear cutter - Measuring range 0-10000 Stiffness Units of Taber.

• Electronic Stiffness Tester - Measuring range 0-5000 mN, accuracy of load cell within 2% of the true reading but not better than 1% of 5000 mN. With imported load cell.Option : Other measuring range 0-10000 mN.

• Resonant Stiffness Tester - is intended for determination of stiffness of newsprint and multilayer carton board performing non destructive test.Range : 1 - 10, 000 of Resonance stiffness

• Crease Stiffness Tester - (Pira type) Important in the folding of carton blanks during their erection & column.Range : 0-1000 gf.

APPLICABLE STANDARD: ISO 2493, 5629, TA

For determining the absorptive capacity of paper by measuring the amount of fluid (aquesous or non aquesous, fluids, oil varnishes) absorbed by the paper surface. Suited for evaluating the quality of printing paper with regard to blotting and set off of printing ink and two surface, as well as varnishing and impregrating suitability of paper, Reservoir capacity 250 cm3. Surface to be tested 100 cm2. The direct quadrant balance is provided to give the difference weight of untreated and treated sample.

• AIR FLOW TYPE (ROTAMETER):For determining smoothness and porosity of paper & paperboard, based on rotameter airflow principle. Provide with three imported variable area flow metes (Rotameter) and accessories. Measuring Range : 5-150ml/min, 50-500ml/min, 300-3000ml/min.

• ELECTRONIC SMOOTHNESS & POROSITY TESTER (BENDTSEN TYPE) For determining the smoothness and porosity of paper and board, based on mass flow meter principle. Provided with imported sensor and accessories Measuring Range: 0-300ml/min , 0-3000ml/min.
• DIGITAL BASED with Roughness and Porosity value on 4.5 Digit seven segment Display
• MICROCONTROLLER BASED system with parameter inputs and all output of Roughness, Porosity and Permeability on LCD display and inbuilt Printer.

This equipment measure the roughness / smoothness as per the condition in the printing press nip at the moment of printing, by clamping the sample between a precise measuring head and a specially backing assembly with variable clamping pressure. Ideally suitable for writing printing, coated paper and paperboard. The micrometer values measure directly on calibrated Variable Area flow Meters (Rotameters/digital Panel Meter)

• Rotameter Model : (Variable Area Flow Meter) Measuring Range : 0.9-6.0m(Micrometers)
• Digital Model (Microcontroller Based) Measuring Range 0.6-6.0 m (Micrometers)

• DENSOMETER (GURLEY TYPE) For measuring porosity, air permeability or air resistance of paper and paper products by determining the time necessary for a certain volume of air flow through the inserted sample, under a uniform pressure. Options : Digital self starting timer

• SMOOTHNESS, POROSITY & SOFTNESS TESTER (GURLEY TYPE) For testing the average smoothness, porosity and softness of paper and films by determining the time necessary for a certain volume of air to flow through the inserted sample, under a uniform pressure.

• HIGH PRESSURE POROSITY & SOFTNESS TESTER (GURLEY TYPE) For measuring the high pressure porosity & softness of paper and films by determining the time necessary for a certain volume of air through the inserted sample, under a uniform pressure.

Optional :

• ELECTRONIC SELF STARTING TIMER : As an optional accessory, for automatic measuring of either 25, 50, 100, 150, 200 or 300 cm3 air to pass through the test specimen. The timer starts automatically when the zero slit of the graduated ruler pass an optional read fork and stops automatically as soon as the predetermined volume of air has been passed through the sample.

Fibretec's permeability tester is accurate on a large range of permeabilities. It is widely used for testing paper, paper machine forming fabrics, press felts & dryer fabrics and filter papers. The accuracy of tester is based on the large flow of outlet area (10cm2) of the measuring head. The orifice disc with 6 different hole diameters gives a wide range of permeability from 150 - 16000 m3/hm2. The display of the input pressure and pressure difference is displayed on Digital Pressure Gauge with imported pressure transmitter. Variable fan speed adjustor.

To measure the Degree of curl when one side of the paper sample exposed to water. The maximum curvature is proportional to that produced when printing paper is in use. Moreover, by measuring the time required till curvature become maximum, a scale is obtained as curl size degree which enables to compare with the relative degree of sizing.

Water Drop Tester or Surface wettability Tester (STFI TYPE) for determining the contact angle of liquid drop of water, oil wetting agent & size for corrugated fiber board. Projection screen of matt glass 160x90 mm. magnification 25 x

For determining the oil absorption resistance of the surface of paper and paperboard. Using an average of 10 tests, the Surface Oil Absorption Time can be determined. The Surface Oil Absorption Time is the time taken for the 75% of the surface covered by oil to have absorbed the oil. The test is very sensitive to temperature. Inclined plane 500 x 100 mm with a 4.5 degree gradient. Inclined plane covered with rubber offset blanket. Brass Roller 2.1 Kg, 76 mm diameter and 55 mm. Oil burette delivers 0.02G oil droplet. Steel holder for oil burette. Electronic self starting timer as an optional accessory.

For determining the penetration time of oil and other liquids through paper and other similar materials. Provided with cooling system, Electronic PID control for constant temperature regulation and Electronic Self Starting Timer in built.

For determining the water absorbency of paper, paperboard and corrugated fiber board. Measures the increase of a sample, exposed to water for a given time. Test area 100 cm2. With couch roll of width 210mm, weight 10 kg.

• Automatic : Spring loaded sample clamping.
• Tilting Type : Lid clamped by way of spring loaded finger grip.

For measuring the degree of water absorption of paper & cloth by the principle of the capillary rise in millimeters by suspending a specimen in a vat filled with water. Eight pieces of specimens (15 mm wide) are clamped at the top, their lower end is exposed to water in the vessel at the bottom and the amount of water absorbed and risen in the specimens is read from the scale and time. Similarly absorption characteristics of liquids like ink, oil etc. can also be measured. Scale Range 0-200 mm.

• For determining the internal bond strength of paper, board and laminates. Dual capacity pendulum of 0-0.25 FT/LB and 0.1-0.5 FT/LB. Readings directly on calibrated scale.

• For determining the internal bond strength of paper, board and laminates. Reading consolidated into one scale upto 0.347 FT/LB. Reading directly on digital display panel.

For measuring the Canadian Freeness number which is a measure of the drainage capacity of different pulp types. It is a useful index of the amount of mechanical treatment given to the pulp with standard screen plate and Plexiglas measuring cylinder for CSF value

For measuring the drainage capacity of beaten pulp and checking the progress of beating process

• Model with provision of Mechanically Controlled valve lifting and Plexiglas measuring cylinder for Scnopper Riegler value with standard wire mesh as per SCAN
• Model with provision of Motorized Controlled valve up and down lifting with a single and plexiglas measuring cylinder for Schopper Riegler valve with standard wire mesh as per SCAN
• Model with provision of Pneumatically Controlled valve lifting and Plexiglas measuring cylinder for Schopper Riegler valve with standard wire mesh as per SCAN

For measuring the initial wet web strength and elongation of newsprint strip or pulp. Microcontroller based system with digital LCD display with automatic return rupture. Clamping length 50 & 100 mm, wire covered clamps for 20 mm wide strips, Max. stroke 30 mm. Deformation speed 1.5 0.1 mm/sec. Measuring range 0-19.999 N. With inbuilt/external printer for printouts of Initial Wet Web Tensile Strength, Stretch and Wet Web Tensile energy absorption. Print report consists of the average tests, Lot No., Serial No., Date, Time and GSM and other feeded parameter. Option : Graphic recorder.

For measuring the PIN HOLE resistance against air and moisture. The Particle Counting Chamber for use with the Gelbo Flex from non-woven materials in a 30 second time period of flexing. Using ISO 9073-10, FIBRETEC have designed the Gelbo Flex Tester with Particle Counter for measuring the linting of non-wovens in the dry state. This test can also be applied to other textile materials.

To check evaluate the interfacial adhesion properties of flexible packaging material peak values, automatic or normal zero setting, overload and over travel protection facility.
Load cell range : 0-5000 gm.

Designed to determine the wear and durability of paper and board, ceramics, plastic textile, rubber, flooring and painted lacquered and electroplated surface. Electrically driven with predetermined cycle counter. Option : With digital predetermined cycle counter. Standard Abrasion test wheels.

APPLICABLE STANDARD:

• DIGITAL MODEL : Heavy Duty tester to determine the compression strength of corrugated & non-corrugated boxes. The instrument provide the Digital Display of load and elongation. Complete with memory for retaining peak value., automatic or normal zero setting, AC/DC drive provide the variable compressive speed overload and over travel protection facility. Measuring range 1000 & 2000 Kg. Platen size 500mmx500mm, 1mtrx1mtr.

• Microcontroller Based System : Heavy duty tester to determine the compression strength of the corrugated box. Load range selected to completely collapsed as peak load or may be with pre-determined load for a given period to evaluate stacking load. Imported AC/DC drives provide the variable compressive speed. Measuring range 1000 Kg. or 2000 Kg. Platen size 500mmx500mm, 1mtrx1mtr.

• Computerized BOX COMPRESSION Tester - Monitoring is done through the FBI MONITOR SYSTEM which is a PC-based laboratory data acquisition system designed around the unique operating system such as WINDOWS 9X, ME & XP. The software makes automatic calculations through COMPUTER MICROPROCESSORS and presentation of measured strength values, arithmetic mean, peak value, selection and conversions of units of Kgf or K N. The graphical strength presentation of the test series Vs time is there. All of which ensure accurate and stable test weights. Measuring range 1000 Kg. or 2000 Kg. Platen size 500mmx500mm, 1mtr x 1mtr. Labview based computer software for visual display.

The ink rub tester is designed to determine the quality of adhesion and scuff resistance of ink to paper surfaces. Dry and wet rub can be performed on the ink rub tester. The method of the preparation is that a 2 lb or 4 lb weight with a clean white board is swept across the test piece for a set number of times, then closely examined. The rate of rubbing (no. of strokes) can be set by the pointer as desired. Abrasion speed approx. 43 cpm, arc motion approx.21/4 inch, counter 0 to 9999 cpm.

The falling dart impact tester covers your determination of the energy that causes Polyethylene film to fail under specified conditions, with the impact of the free falling dart. This energy is expressed in terms of weight of the dart falling from a specified height, which would result in 50% failure of specimen tested. The unit employs a dart, with a 38 mm diameter hemispherical head, dropped from a height of 660 mm. Option: Motorized lifting of package & solenoid operated release system. Heavy weight version upto 500 lbs capacity.

To determine the ability of package to with stand the rigors of handling by people and machinery in the distribution environment. Control and hoisting features facilities in all respects of operation : drop height setting and test reset. The equipment has steel base plate complies with industry standard. Adjustable maximum and minimum height for loading and dropping via chain hoist for positioning. Maximum drop height 2.5 mt and lifting capacity 150 Kg. Steel Base for test surface 1000x1500x25. Option: Motorized lifting of package & solenoid operated release system. Heavy weight version upto 500 lbs capacity.

For determining the puncture resistance of corrugated board by measuring the energy required to puncture it. Interchangeable weights supplied to cover four energy ranges i.e. 0-5, 0-10, 0-20 & 0-36 Newton Meter.

For determining the impact strength of the boxes/containers made from cardboard, plastics or wooden materials. Different models available in capacities ranging from 600-6000 pounds with necessary modification in respect of track length, dolly size etc. Ruggedly built design to withstand continuous usage. Has automatic release mechanism. Complete with traveling chain driving motor.