Evelta Electronics Private Limited

Juinagar, Navi Mumbai, Maharashtra

PACKAGE CONTENT

1. OV5640 Camera Board (B) x1

Features

1. Pixels: 5 megapixel
2. Resolution: 2592x1944
3. Sensor: OV5640
   • 1.4um x 1.4um pixel with OmniBSI technology, high sensitivity, low crosstalk, low noise
   • Automatic image control functions: AEC, AWB, ABF, ABLC, etc.
   • Image quality controls: color saturation, hue, gamma, sharpness, lens correction, etc.
   • Supports image scaling, panning, windowing, etc.
4. Lens:
   • CCD size: 1/4inch
   • Aperture (F): 2.5
   • Focal Length: 2.0mm
   • Diagonal: 170 degree (fisheye)
5. Output Formats:
   • YUV(422/420)/YCbCr422
   • RGB565/555/444
   • CCIR656
   • RAW RGB
   • Compressed Data
6. Operating Voltage: 3.3V
7. Control Interface: SCCB (I2C compatible)
8. Data Interface: DVP 8-bit
9. Dimension: 35.70mm 23.90mm

ACS712 current sensor IC is an accurate, fully integrated effective Linear Current Sensor IC based on Hall Effect. The ACS712ELCTR-05B-TIC is SOIC8 packagedto give economical and precise solutions for AC or DC current sensing for max 5A current measurement, operating at 5V DC.

For measurement, the device can be plugged to measure both AC and DC voltage at its input and its output which is linear with respect to the measured input showing varied analog voltage as the output.ACS712-5A ensures the device safety standards by incorporating thick copper conductor on the input side for protection from the 3-5 times overcurrent conditions. The device has zero magnetic hysteresis and extremely stable offset voltage.

The ACS712ELCTR-05B-T IC is electrically isolated with no use of any costly isolation techniques making it best suited for the application in motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection.

Datasheet

The Allegro ACS759 is an optimized and accurate linear Hall sensor circuit based Current Sensor IC for AC/DC current sensing for max 50A current measurement, operating upto 3.6 V DC. With improved noise reduction by introducing proprietary amplifier and filter design providing economical and precise solutions for AC or DC current sensing applications. Small package size with easy mounting with through hole facility. The sensor is also integrated with shield preventing long time heavy currents capacitive coupling.

Datasheet

This is an AC current measuring sensor featuring CT technology, CT stands for current transformer, a transformer unit split in two half like a clamp for measuring alternating current source.

Non-invasive AC Current Sensor can measure a load up to 100 Amps AC source, simply clamp the current sensor on the live wire or neutral wire. The sensor measure the amount of current flowing through the wire. The output is a small AC signal which can be further use for energy meter application or for over-current protection of AC devices. To facilitate the application need the sensor has 3.5mm jack on the output side.

Popular application of Non-invasive current sensor are like safeworking on the high voltage electrical lines, protection of over current of the electrical device like AC motor, Air compressor.

This is an AC current measuring sensor featuring CT technology, CT stands for current transformer, a transformer unit split in two half like a clamp for measuring alternating current source.

Non-invasive AC Current Sensor can measure a load up to 10 Amps AC source, simply clamp the current sensor on the live wire or neutral wire. The sensor measure the amount of current flowing through the wire. The output is a small AC signal which can be further use for energy meter application or for over-current protection of AC devices. To facilitate the application need the sensor has 3.5mm jack on the output side.

Popular application of Non-invasive current sensor are like safe working on the high voltage electrical lines, protection of over current of the electrical device like AC motor, Air compressor.

This is a low cost, high sensitive carbon monoxide gas detector sensor. This sensor is best suitable for the detection of the CO gas in car, industry.

This is a low power consumption multi-layer metal oxide semiconductor type gas sensor. It is highly sensitive to carbon monoxide and high resistance to alcohol vapour. It is ideally used for smoke detection. A pulsed voltage is applied on one second voltage cycle to prevent the possible migration of the heater material in extreme environmental condition.

This is a low cost, quick response alcohol detector sensor. This sensor is best suitable for the detection of the alcohol detecting setup/alarm.

Hall Effect Sensor AH34 is a low noise linear analog output sensor device which opens wide scope of measurements related to displacement, angular position and current ratings. These sensors shows ratio metric property as the output voltage of the sensor is proportional to the applied magnetic field. The AH34 hall sensor is packaged in 3 pin ultra mini SIP, which confers to the industrial requirement for small size, high accuracy and extensive work capacity avoiding any type of mechanical stress. Each sensor has inbuilt BiCMOS monolithic circuit with temperature compensating circuitry and an amplifier for processing low signal and high gain.

The device can withstand extreme environment conditions with temperature ranging from -40oC to 150oC. The device is lead (Pb) free and best suited in application of automotive and industrial applications.

AM1001 isresistance type humidity sensors, analog voltage output sensor signal; withhigh accuracy, high reliability, consistency, easy to use, inexpensive, and is particularly suitable for quality, cost-demanding enterprise.

With additionallyelectronic read-out of tracking information for humidity sensor, the device is extremely small in size with digital footprint of 3 x 3 mm. SH21 integrates sensors, calibration memory and adequate area for footprint. SH21 is fully protected with anti-shock facility and prevention from the expose of volatile chemicals.

This small IC finds application on users customized development / special application board demand. Output of the sensor is calibrated and linearized in digital and I2C format.

Datasheet