Esteem Power Equipments India Pvt. Ltd.

Senapati Bapat Road, Pune, Maharashtra

These are special type Heat Exchangers we have developed for Pharma and Process Industry applications. This comes in various types of MOC like Carbon Steel (CS), Stainless Steel (SS304, SS316) etc to suit the process. We have supplied such type of Heaters to M/S Alfa Laval, Abott Laboratories etc.

We design and manufacture Direct Fired Hot Air Generators on Gas or liquid fuel . HAGs are widely used for drying application of products like bulk drugs, chemicals, food & pharmaceutical grade, which requires very high process air temperature range between 250C to 650C. We design and manufacture Indirect Fired Hot Air Generators on liquid or solid fuels to avoid the product contamination with flue gases.HAGs are widely used for drying application of products like bulk drugs & chemicals, which requires moderate process air temperature range between 180C to 300C. We design and manufacture Coal Fired Hot Air Generator .This is a unique product developed to reduce the drying cost, as pulverized coal is used to generate the hot air for drying application of products like bulk drugs & chemicals which requires very high process air temperature range from 250C to 650C.

We design and manufacture silencer for 1. Superheated steam 2. Saturated steam 3. Start up and warm up vents 4. Blow down applications 5. For any other steam vents Our design of silencer is completely customized suitable for customers requirements and site conditions. For Silencer design we follow guidelines as per OSHA and basic silencer design is as per ASME sec VIII div. I. We have wide range of silencers from 0.5TPH to 100TPH steam flow and for pressure 2kg/cm2(g) to 150kg/cm2(g).

Oxygen in feed water is always harmful to boilers it corrodes metal parts.Deaerators are used to remove free Oxygen from boiler feed water performance of Deaerator is depend upon effective method of activity maximum water and steam surface contact with higher time of contact. Our design achieves these requirements very efficiently by planned spray pattern, highly effective scrubbing by multiple tray arrangement and mixing incoming steam with water. We can residual O2 level below 0.007 PPM after deaeration which satisfies requirement of modern high boilers.

The blow down water is discharged at high temperature and pressure. When such a liquid is discharged to atmospheric pressure, there is flashing due to sudden reduction in pressure. Therefore the blow tank is provided at the end of blow down line.

These are Shell and Tube Type of Heat Exchangers. LP and HP Heat Exchangers means Low Pressure and High Pressure Heat Exchangers respectively. We Design shell and Tube type Heat exchangers as per IBR or TEMA Standard.

Super heater super heats the saturated steam coming from Steam drum to reduce the moisture content of steam. The super heater tubes are supported by baffles plates. Super heater is equipped with nozzles for steam inlet outlet, HTF inlet outlet, drain, vent, pressure and level gauges, saddle, lifting hook arrangements etc.

We design and manufacture coil rapping mechanism for cleaning operation.Coil rapping mechanism is new development to remove soot from coil surface which is exposed to flue gases. This is a very new technique and no steam is required to blow soot like regular soot blowers.

We design and manufacture economizers based on the available flue gases and the temperature of flue gases. Waste heat recovered from flue gases used for different applications .We design three types of economizers 1) Plain tube 2) Finned tube 3) Gilled tube.

We design manufacture steam drum for boiler applications.The Steam drum is connected to the Evaporator through risers and down comers which generates the saturated steam which is separated in Steam Drum. The Steam Drum is consisting of Demister Pad to give the saturated dry steam, blow down distribution pipe, chemical dosing distribution pipe. The Drum is provided with the both side manhole and necessary nozzles connections.

Spin flash dryer is useful for drying the wet cake at moderate temperature of process air and specific particle size is not required,

Flash dryer is useful for drying the feed/wet cake at very high temperature of process air and specific particle size is not required, like

We design and manufacture an air preheater (APH) to heat air before another process (for example, combustion in a boiler) with the primary objective of increasing the thermal efficiency of the process.The purpose of the air preheater is to recover the heat from the flue gas which increases the thermal efficiency of the boiler by reducing the useful heat lost in the flue gas. These are having applications in pharma, chemical and food industries.

In this , the waste heat recoverd from flue gases is used for heating thermic fluids .Thermic fluid can be used as secondary medium which can transfer and exchange recovered waste heat for various applications like - water heating, steam generation, air heating, raw material pre heating etc.

We design and manufacture waste heat recovery unit to capture available waste heat for water heating.This hot water can be used for various purposes like-Boiler feed water, process water, to run absorption chillers etc.