Enviro Tech Industrial Products

Gandhi Nagar, Delhi

PM-1 Digital Pen Meter

Model PM-1 Digital Pen Meter

Measures DC/AC Voltage, Resistance, Continuity, Diode, Frequency

Our compact, low cost Model PM-1 Digital Pen Meter is ideal for general electrical testing and troubleshooting. A few applications include HVAC, automotive, electrical/power, and environmental monitoring uses. This meter measures DC and AC voltage to 600 V and resistance to 40 M Ohms. In addition to volts and ohms, the digital pen meter includes continuity, diode, and frequency tests to 10 kHz. This meter features data hold, REL (relative value), and auto range buttons. The 4 digit LCD displays value, mode, and low battery indication. The Model PM-1 is furnished with red and black test leads, batteries and carrying case with belt clip.

ModelDescription

• PM-1Digital Pen Meter

Specifications

• Over Voltage Category:CAT IV 600 V.
• AC Voltage:1 mV to 600 V (1.0% + 3 dgt).
• DC Voltage:0.1 mV to 600 V (0.8% + 2 dgt).
• Resistance:0.1 to 40M (1.0% + 3 dgt).
• Continuity:Audible buzzer.
• Diode Test:1.5 VDC.
• Frequency:0.001 Hz to 10 KHz (0.8%+2 dgt).
• Display:4000 counts plus decimal point.
• Power Requirements:(2) AA alkaline batteries, included, user replaceable.
• Weight:5.3 oz (150 g).

PM-2 Phase Rotation Digital Pen Meter

Model PM-2 Digital Pen Meter with Phase Rotation

Measures DC/AC Voltage, Resistance, Continuity,

Frequency and Phase Rotation

Our compact, low cost Model PM-2 Digital Pen Meter is ideal for general electrical testing and troubleshooting. A few applications include HVAC, automotive, electrical/power, and environmental monitoring uses. This meter measures DC and AC voltage to 600 V and resistance to 1499 Ohms. In addition to volts and ohms, this meter includes continuity, diode, and frequency tests to 69.9 Hz. Along with the mentioned functions, the PM-2 has the ability to perform a phase test from 100 to 600 V. This meter features data hold, display (to show voltage and frequency during AC tests), and clear screen buttons. The 4 digit LCD features value, mode, and low battery indication. The Model PM-2 is furnished with red and black test leads, batteries and carrying case with belt clip.

ModelDescription

• PM-2Digital Pen Meter with Phase Rotation

Specifications

• Over Voltage Category:CAT IV 600 V.
• AC Voltage:1.5 V to 600 V (1.5% rdg + 5 dgt).
• DC Voltage:1.5 V to 600 V (0.8% rdg + 1 dgt).
• Resistance:1 to 1499 (1.0%+5 dgt).
• Continuity:Audible buzzer.
• Phase Test:100 to 600 V.
• Frequency:0.1 Hz to 69.9 Hz (1.0% + 2 dgt).
• Display:6000 counts plus decimal point.
• Power Requirements:(2) AA alkaline batteries, included, user replaceable.
• Weight:5.3 oz (150 g).

Portable Ultrasonic Flowmeter Kit

Series PUB Portable Ultrasonic Flowmeter Kit

Portable and Non-Invasive

The Series PUB & PUF Portable Ultrasonic Flowmeter Kits utilize the transit-time difference for measuring flow rates in pipes non-invasively. They are compact and lightweight instruments incorporating the latest electronics and signal processing technologies, realizing high performance and easy operation. These devices are perfect for on-the-go flow monitoring, capable of 20 hours continuous operation with built-in, rechargeable battery. The PUB comes with a rugged carrying case with molded foam inserts while the PUF boasts an IP67 rated case to hold and protect all equipment conveniently. Their screens offer easy to read text with convenient backlight for visual comfort. The efficient layout of the function keys adds to these units easy to use programming. These series offer analog as well as a pulsed outputs.

PRINCIPLES OF OPERATION

Two sensors are placed on the exterior of the pipe, and each transmits an ultrasonic pulse through the pipe and fluid to the other. The velocity of the liquid flowing through the pipes causes the pulse to accelerate or decelerate. The difference in the transit times of the two pulses is used to calculate the flow rate. The use of transit time allows the flowmeter to be unaffected by pressure or temperature changes.

Specifications

• Service:Homogeneous liquids that do not contain air bubbles capable of ultrasonic wave propagation.
• Inputs:Lemo connector cable from sensors.
• Range:0.33 to 65.62 ft/s (0.1 to 20 m/s).
• Display:240 x 64 pixel graphic display, high contrast black on white with backlight; Languages: English, French, German, Swedish, Italian, Spanish, Portuguese, Russian, Norwegian, and Dutch; 5.2" W x 1.5" H.
• Accuracy:0.5 to 2% of flow reading for flow rate > 0.66 ft/s (0.2 m/s) and pipe ID > 2.95" (75 mm); 3% of flow reading for flow rate > 0.66 ft/s (0.2 m/s) and pipe ID in range 0.512 to 2.95" (13 to 75 mm); 6% of flow reading for flow rate < 0.66 ft/s (0.2 m/s).
• Power Requirements:9 to 24 VDC, (1) 5-Cell NiMH battery, internal, factory replaceable (continuous operation time: 20 hours with back-light and output off) (recharging time: 6.5 hours, power adapter used).
• Power Consumption:10.5 W.
• Power Adapter:110/240 VAC adapter. UK, US, European adapters included.
• Temperature Limits:-4 to 275F (-20 to 135C).
• Outputs:Analog: 1 opto-isolated output: 4 to 20 mA, 0 to 16 mA or 0 to 20 mA (selectable); Error current: 0 to 26 mA (selectable); Load resistance: 620 max;
• Pulse: 1 opto-isolated MOSFET relay, 150 mA max, 500 pps max, 200 Hz max.
• Enclosure Rating:Converter: IP54; Transducers: IP51.
• Materials:Flame retardant injection molded ABS plastic.
• Repeatability:0.5 % of measured value or 0.066 ft/s (0.02 m/s).
• Electrical Connections:Multi-pin Lemo plugs.
• Turbidity:< 3% by volume of particulate content.
• Permissible Air Content:< 3% by volume.
• Response Time:< 500 ms.
• Weight:Unit without accessories: 2.3 lb (1.06 kg); Unit with accessories in carrying case: 13.23 lb (6.0 kg).
• Agency Approvals:CE.
• ADDITIONAL SPECIFICATIONS
• Applicable Pipe Material:Carbon steel, SS, copper, UPVC/PVDF, concrete, galvanized steel, mild steel, glass, brass.Applicable Pipe Lining:Rubber, glass, concrete, epoxy, steel, other*.
• Pipe Wall Thickness:0.04 to 3" (1 to 75 mm).
• Pipe Lining Thickness:< 1" (< 25 mm).
• *Selectable option for special material with known propagation rate of the lining material.

Model 641B Air Velocity Transmitter

Dirty Air Flow Applications

A Low-Cost, Direct Reading Instrument Used for Both Air Velocity & Static Pressure TestsThe Model 641B Air Velocity Transmitter uses a heated mass flow sensor suitable for dirty air flow applications. It has user-selectable ranges from 250 FPM (1.25 MPS) to 2000 FPM (10 MPS).

Product Applications

• Exhaust stack flow monitoring
• Air control in drying processes
• HVAC air velocity measurements
• Fan supply and exhaust tracking
• Clean room ventilation monitoring

ModelDescription

• 641B-4Air velocity transmitter.
• 641B-4-LEDAir velocity transmitter with LED display.

Specifications

• Service:Air and compatible, non-combustible gases.
• Accuracy:5% FS process gas: 32 to 122F (0 to 50C); 6% FS process gas: -40 to 32F & 122 to 212F (-40 to 0C & 50 to 100C).
• Response Time:Flow: 1.5 s to 95% of final value (output filter set to min).
• Temperature Limits:Process: -40 to 176F (-40 to 80C). Ambient: 32 to 140F (0 to 60C).
• Humidity Limit:Non-condensing.
• Power Requirements:12 to 35 VDC, 10 to 16 VAC. 1.5 A rating required on supply due to initial power surge drawn by transmitter.
• Output Signal:4 to 20 mA, isolated 24 V source, 3 or 4-wire connection.
• Output Filter:Selectable 0.5-15 s.
• Loop Resistance:600 max.
• Current Consumption:300 mA max*.
• Electrical Connections:Screw terminal.
• Enclosure Rating:Designed to meet NEMA 4X (IP66) for non-LED models only.
• Mounting Orientation:Unit not position sensitive.
• Weight:12.6 oz (357.2 g).
• *A brief current transient exceeding 300 mA may be seen on startup.

Features

• SS sensor suitable for dirty air flow measurement
• Ranges from 250 FPM (1.25 MPS) to 2000 FPM (10 MPS)
• 4 to 20 mA output
• Digital filter for signal damping

Accessories

Model NumberDescription

• A-155Cable gland with 1/2" male NPT fitting.
• A-156Flange mounting plate with 1/2" female NPT.

Related Products

• Series 641RM Air Velocity Transmitter with Remote Probe
• Series 641RM Air Velocity Transmitter with Remote Probe
• Model VT120 Integral Vane Thermo-Anemometer
• Model VT120 Integral Vane Thermo-Anemometer
• Series AVU Air Velocity Transmitter
• Series AVU Air Velocity Transmitter
• Model VT-200 Vane Thermo-Anemometer
• Model VT-200 Vane Thermo-Anemometer
• Series 641 Air Velocity Transmitter
• Series 641 Air Velocity Transmitter
• Technical Reference Books
• Technical Reference Books

Ellipsoidal Tip Pitot Tube

Series 160E Ellipsoidal Tip Pitot Tube

Designed to Meet ISO Standard 3966

The Series 160E Ellipsoidal Tip Pitot Tube uses a precision crafted tip configuration, which allows air to pass smoothly with minimum turbulence for consistent, reliable readings. Sliding depth indicators grip firmly to ensure uniform insertion when measuring traverses across ducts. Total and static pressure taps are 1/4" (6 mm) and are permanently silver soldered to the connection block, making them leak-proof and durable.

Product Applications

• Monitor or control air velocity or air flow when combined with differential pressure gage, switch, or transmitter

ModelDescription

• 160E-00Ellipsoidal tip Pitot tube, 0.2 meter insertion length.
• 160E-01Ellipsoidal tip Pitot tube, 0.3 meter insertion length.
• 160E-02Ellipsoidal tip Pitot tube, 0.48 meter insertion length.
• 160E-03Ellipsoidal tip Pitot tube, 0.8 meter insertion length.
• 160E-04Ellipsoidal tip Pitot tube, 1.0 meter insertion length.
• 160E-05Ellipsoidal tip Pitot tube, 1.22 meter insertion length.
• 160E-06Ellipsoidal tip Pitot tube, 1.52 meter insertion length.
• 160E-UEllipsoidal tip Universal Pitot tube, attaches to any length of 3/4" sch. 40 pipe.

Features

• Designed to meet ISO standard 3966 commonly required in UK and Europe
• Ellipsoidal tip design for improved accuracy
• 304SS construction adds strength, resists corrosion
• Adjustable depth indicators for fast, consistent traverses
• Alignment indicator helps keep tip parallel to flow

Accessories

Model NumberDescription

• A-160-CASEPitot tube carrying case.
• A-532Air velocity calculator slide chart.

Related Products

• Series MS Magnesense Differential Pressure Transmitter
• Series MS Magnesense Differential Pressure Transmitter
• Series FLST Duct Mounted Airflow Measurement Station
• Series FLST Duct Mounted Airflow Measurement Station
• Series ADPS/EDPS Differential Pressure Switch
• Series ADPS/EDPS Differential Pressure Switch
• Series STRA Duct Mounted Airflow Measurement Station
• Series STRA Duct Mounted Airflow Measurement Station

wmt2 multi jet water meter

series wmt2 multi-jet water meter with pulsed output

economical, brass body, dry dial, pulsed output

the series wmt2 multi-jet water meter is a series of mechanical, water totalizing meters that display the total water usage in gallons or m3 and provide a reed switch output proportional to flow rate. They are available in a range of body sizes and include npt or bspt couplings.

not for potable water use, brass contains lead in excess of low lead limits.

product applications

• water monitoring
• irrigation
• cooling systems
• filtration systems

modeldescription

• wmt2-a-c-015/8" x 1/2" brass multi-jet water meter (gpm), with pulse output, 0.1 gal/pulse.
• wmt2-a-c-01-15/8" x 1/2" brass multi-jet water meter (gpm), with pulse output, 1 gal/pulse.
• wmt2-a-c-025/8" x 3/4" brass multi-jet water meter (gpm), with pulse output, 0.1 gal/pulse.
• wmt2-a-c-02-15/8" x 3/4" brass multi-jet water meter (gpm), with pulse output, 1 gal/pulse.
• wmt2-a-c-033/4" brass multi-jet water meter (gpm), with pulse output, 0.1 gal/pulse.
• wmt2-a-c-03-13/4" brass multi-jet water meter (gpm), with pulse output, 1 gal/pulse.
• wmt2-a-c-041" brass multi-jet water meter (gpm), with pulse output, 0.1 gal/pulse.
• wmt2-a-c-04-11" brass multi-jet water meter (gpm), with pulse output, 1 gal/pulse.
• wmt2-a-c-04-1001" brass multi-jet water meter (gpm), with pulse output, 100 gal/pulse.
• wmt2-a-c-06-101-1/2" brass multi-jet water meter (gpm), with pulse output, 10 gal/pulse.
• wmt2-a-c-07-102" brass multi-jet water meter (gpm), with pulse output, 10 gal/pulse.
• wmt2-a-c-07-1002" brass multi-jet water meter (gpm), with pulse output, 100 gal/pulse.
• wmt2-b-c-08-11/2" bspt (15mm) brass multi-jet water meter (m3/h), with pulse output, 1 l/pulse.
• wmt2-b-c-08-101/2" bspt (15mm) brass multi-jet water meter (m3/h), with pulse output, 10 l/pulse.
• wmt2-b-c-10-13/4" bspt (20mm)brass multi-jet water meter (m3/h), with pulse output, 1 l/pulse.
• wmt2-b-c-11-11" bspt (25mm) brass multi-jet water meter (m3/h), with pulse output, 1 l/pulse.
• wmt2-b-c-12-11-1/4" bspt (32mm) brass multi-jet water meter (m3/h), with pulse output, 1 l/pulse.
• wmt2-b-c-12-101-1/4" bspt (32mm) brass multi-jet water meter (m3/h), with pulse output, 10 l/pulse.
• wmt2-b-c-12-1001-1/4" bspt (32mm) brass multi-jet water meter (m3/h), with pulse output, 100 l/pulse.
• wmt2-b-c-14-102" bspt (50mm) brass multi-jet water meter (m3/h), with pulse output, 10 l/pulse.
• wmt2-b-c-14-1002" bspt (50mm) brass multi-jet water meter (m3/h), with pulse output, 100 l/pulse.

specifications

• service:water.
• wetted materials:body: brass, polyethylene;
• couplings: brass;
• measuring chamber: polyethylene, abs plastic, ferrite, acetal.
• flow range:see model chart on catalog page.
• accuracy:transitional flow: 5%; nominal flow: 2%.
• temperature limit:104f (40c).
• pressure limit:232 psi (16 bar).
• totalizing display maximum:see model chart on catalog page.
• output signal:pulse output with frequency proportional to flow rate.
• pulse options:0.1 gal, 1 gal, 10 gal, 100 gal per pulse (1 l, 10 l, 100 l per pulse).
• electrical rating:0.01 a @ 24 vac/dc.
• electrical connections:color-coded lead wires, 4.5' (1.5 m) long.
• mounting orientation:horizontal.
• weight:see dimension chart on catalog page.

battery powered temperature indicator

series bpi battery powered temperature indicator

rtd or t/c input, 4-digit display, selectable f or c

the series bpi battery powered indicator accepts rtd or thermocouple input and provides local or remote display of temperature measurements. Quickly navigate the menu system to customize for each application. Three push buttons allow the user to select input type, engineering units (f or c), offset temperature, decimal point position, and password protection. The indicator is housed in a polycarbonate nema 4x (ip66) enclosure for additional protection from the environment.

product applications

provides local temperature indication in areas without power availability

modeldescription

• bpi-101 battery powered temperature indicator, 3-wire pt100 or ni120 input.

specifications

• inputs:thermocouple or rtd depending on model.
• accuracy:thermocouple input: 0.1% of fs, 0.5c (plus sensor); rtd: 0.2c 0.1% of reading (plus sensor error).
• power requirements:3.6 v aa lithium metal battery, included, user replaceable.
• battery life:>2 years.
• display:0.3" (7.6 mm) 4-digit lcd.
• resolution:0.1c.
• ambient operating temperature:14 to 158f (-10 to 70c).
• storage temperature:-4 to 185f (-20 to 85c).
• weight:6.0 oz (170 g).
• front panel protection:nema 4x (ip66).
• agency approvals:ce.

features

• programmable input type, engineering units (f/c), offset temperature, decimal point position, and password protection
• four-digit segmented display

bar graph meter

series bgm bar graph meter

clear relative position and high resolution in one

the series bgm digital bar graph meter is extremely durable and can replace a wide range of analog meters. The 4-digit display will significantly reduce the potential for human error in reading by eliminating errors commonly produced by the viewing angle when reading analog meters. This series has a key pad that allows for easy access of features without complex menu structures. With the combined ability to create a wide range of custom faceplate and the optional nema 4x bezel, the series bgm can be used in a variety of applications. The led bar graph adds a visual indicator of the measured value so that it can be visually analyzed, preventing accidents or system failures from happening.

product applications

• visual location and indication of flow, level or air velocity

specifications

• inputs:0 to 10 vdc or 4 to 20 ma.
• accuracy:0.05% fs.
• power requirements:120 vac 50/60 hz, 5 to 12 vdc, or 10 to 30 vdc model dependent.
• power consumption::120 vac: 2.4 w @ 20 ma max; 5 to 12 vdc: 1.2 w @ 100 ma max; 10 to 30 vdc: 1.5 w @ 50 ma max.
• display:led display: 4 red colored digits, 0.3" height; led graph: 31 element bar, 0.2" w x 3.1" l (5.08 mm w x 78.74 mm l).
• decimal point:3 positions, user selectable.
• temperature limits::operating: -13 to 176f (-25 to 80c); storage: -67 to 176f (-55 to 80c).
• enclosure rating:nema 1 or nema 4x, model dependent ip65 front.
• electrical connections:removable screw terminal blocks.
• outputs:2 spst relay outputs (optional).
• switch rating:1 a @ 200 v.
• enclosure material:bezel: black epoxy enameled steel; window: acrylic; case and mounting bracket: 304 ss.
• time delay:0.5 s.
• weight:40 oz (1.13 kg).

features

• bar graph visual indicator
• high resolution for better precision
• many configurable options to design a meter for any need

temperature and process indicator

series tid temperature/process indicator

low cost, 3-digit display, 1% accuracy

the series tid displays temperature or a process value measured by a ptc or ntc thermistor or a 4 to 20 ma transmitter.

product applications

• panel process indicationrefrigerators, walk in coolers

modeldescription

• tid-1110temperature/process indicator, f, ptc thermistor input, 110 vac.
• tid-1120temperature/process indicator, c, ptc thermistor input, 110 vac.
• tid-1210temperature/process indicator, f, ptc thermistor input, 230 vac.
• tid-1220temperature/process indicator, c, ptc thermistor input, 230 vac.
• tid-1410temperature/process indicator, f, ptc thermistor input, 24 vac/dc.
• tid-1420temperature/process indicator, c, ptc thermistor input, 24 vac/dc.
• tid-3100temperature/process indicator, 4-20 ma input, 110 vac.
• tid-3200temperature/process indicator, 4-20 ma input, 230 vac.
• tid-3400temperature/process indicator, 4-20 ma input, 24 vac/dc.

specifications

• range:-58 to 302f (thermistor); -999 to 999 counts (4 to 20 ma).
• input:ptc/ntc thermistor or 4 to 20 ma.
• power requirements:115 vac, 230 vac, 24 vac/dc.
• accuracy:> 1%.
• display:3-digits, red, green or blue display.
• resolution:1 or 0.1 count.
• front panel rating:ip64. (nema 3r).
• weight:2.3 oz (65 g).
• agency approvals:ce, curus.

features

• thermistor or transmitter input models available
• 3 digit bright led

accessories

model numberdescription

• ts-51ptc sensor, pvc sheath, pvc cable, 10 ft (3 m) cable.
• ts-61ptc sensor, polyamide resin coated brass sheath, pvc cable, 10 ft (3 m) cable.

related products

• series ts-probes digital temperature switch probe

Thermo Hygrometer

Model 485B Thermo-Hygrometer

Measures % RH, Temperature, Dew Point and Wet Bulb

The Model 485B Thermo-Hygrometer is a versatile, compact, handheld instrument for measuring percentage of relative humidity and temperature in F or C. Dew point and wet bulb temperatures are derived from the relative humidity and temperature measurements and are displayed on the LCD.

For Fast and Accurate Calibration Services, CLICK HERE!

Product Applications

• Building commissioningPulp & paper

Models & Ordering

ModelDescription

• 485B-1Digital thermo-hygrometer includes 9V battery, sensing probe, wrist strap, soft carrying case and instructions

Specifications

• Service:Humidity, temperature, wet bulb and dew point temperature detection in clean air.
• Temperature Limits:Process: -40 to 176F (-40 to 80C); Ambient: 5 to 125F (-15 to 51C).
• Range Relative Humidity:0 to 100% (non-condensing).
• Accuracy Relative Humidity:2% FS over 10 to 90% @ 77F (25C).
• Range Temperature:-20 to 140F (-28 to 60C).
• Accuracy Temperature:0.54F @ 72F (0.3C @ 25C).
• Display:4.5 digit LCD.
• Resolution:0.1%, 0.1 F/C.
• Probe Length:8" (203 mm) insertion.
• Power Requirements:9 V alkaline battery, included, user replaceable.
• Weight:16 oz (454 g).
• Agency Approvals:CE.

Features

• Compatible with Dwyer AP1 thermo-anemometer and VP1 100 mm vane thermoanemometer probes (sold separately)
• Hold feature to freeze current readings on the display
• Stores up to 99 readings for future evaluation

Accessories

Model NumberDescription

• RP1Thermo hygrometer humidity & temperature probe with coiled cable.
• A-47X-BOOTRubber boot for manometers (manometer not included).

Related Products

• Model UHH-BTG Wireless Mobile Gateway
• Model UHH-BTG Wireless Mobile Gateway
• Mobile Meter Software Test Instrument App
• Mobile Meter Software Test Instrument App

Flex Tube U Tube Manometer

Series 1221/1222/1223 Flex-Tube U-Tube Manometer

Suitable for Pressures up to 100 psi, Better Precision

These inexpensive manometers measure positive, negative and differential pressures. Dwyer Flex-Tube U-Tube Manometers combine the inherent accuracy of the simple "U" Tube with the durability of tough, long-lasting plastic construction. Columns are of .375" O.D. flexible and shatter proof clear butyrate tubing. They are easily accessible for cleaning. Indicating tube is backed by white scale channel to provide maximum color contrast. Scales are extruded high impact polystyrene plastic, formed to hold columns in perfect alignment. Stark white scales have graduations and numbers silkscreen-printed in black for maximum legibility.

You can choose from numerous models and features including over-pressure safety traps, in full scale ranges from 8" to 36" of water or mercury. All are suitable for total pressures to 100 psi - for determining velocity and static pressures, leakage, fan and blower efficiency, filter resistance, and gas pressures. Ideal wherever a portable, direct reading manometer is needed. Standard ranges and markings as shown, or special ranges, colors, logos and brand names for OEM quantity orders are available.

Product Applications

• Duct static pressure
• Calibration labs
• Filter monitorin

ModelDescription

• 1221-12-W/MU-tube manometer, range 6-0-6" w.c., 7.9 oz (225.5 g) mercury required to fill.
• 1221-16-W/MU-tube manometer, range 8-0-8" w.c., 9.5 oz (269 g) mercury required to fill.
• 1221-20-W/MU-tube manometer, range 10-0-10" w.c., 11.1 oz (314.5 g) mercury required to fill.
• 1221-24-W/MU-tube manometer, range 12-0-12" w.c., 13.4 oz (379.7 g) mercury required to fill.
• 1221-36-W/MU-tube manometer, range 18-0-18" w.c., 17.3 oz (491.1 g) mercury required to fill.
• 1221-8-W/MU-tube manometer, range 4-0-4" w.c., 6.3 oz (178.5 g) mercury required to fill.

Features

• Minor Divisions of 1/10" water column (or 2mm water column on metric units) are silkscreened in jet black on stark white scale for positive definition. Easy to read, even at a distance, they are acrylic coated for permanence. All models are furnished with one 3/4 ounce bottle of fluorescein green color concentrate with special wetting agent for W/M models, or 3/4 ounce bottle of red gage fluid for "D" units.
• Series 1221 Manometer - Our simplest, lowest cost basic U-gage. A dependable U-tube manometer that withstands hard use and provides accurate, high visibility readings. For use with water, mercury or red gage fluid. For mercury filled manometers, a scale clamp bar, Dwyer Part No. A-363 (available as an extra for Series 1221 - and standard on Series 1222) is recommended. One pair of carrying plugs and a pair of non-kink vinyl tube connectors are included with each manometer.
• Series 1222 Manometer - All the features of the 1221 plus magnetic clips for mounting to any vertical steel surface, and clamp bar to insure against U-tube slipping. (Especially recommended for manometers used with mercury.) Both magnets are easily removed and replaced at the user's convenience.
• Series 1223 Manometer - Our finest U-gage - for either portable or stationary use. Safety traps prevent loss of indicating fluid in case of accidental over-pressure. Tubing is permanently bonded to a molded, high impact acrylic plastic top that contains safety traps. Large magnetic clips and clamp bar are provided. Standard type "a" connections include two rapid shut-off type molded nylon tubing connections, two 3' lengths of flexible Tygon plastic tubing, and two 1/8" pipe thread to tube adapters.

Gas Turbine Flow Meter

Series TFP-GV Gas Turbine Flow Meter

PPS Body, 0 to 5 VDC Output

The SERIES TFP-GV Gas Flowmeters utilize a turbine wheel and electro-optical detection to convert flow rates into a linear 0 to 5 VDC output signal for recording and data logging. A power adapter or mating cable assembly is required for operation.

Product Applications

• Industrial flow monitoring
• Commercial systems
• Laboratory equipment

ModelDescription

• TFP-GV03Gas turbine flow meter, range .042 to .21 SCFH (0.02 to 0.1 LPM), 1/8" OD connection.
• TFP-GV04Gas turbine flow meter, range .085 to .42 SCFH (0.04 to 0.2 LPM), 1/8" OD connection.
• TFP-GV05Gas turbine flow meter, range .21 to 1.1 SCFH (0.1 to 0.5 LPM), 1/8" OD connection.
• TFP-GV06Gas turbine flow meter, range .42 to 2.1 SCFH (0.2 to 1 LPM), 1/8" OD connection.
• TFP-GV07Gas turbine flow meter, range .85 to 4.2 SCFH (0.4 to 2 LPM), 1/4" OD connection.
• TFP-GV08Gas turbine flow meter, range 2.1 to 11 SCFH (1 to 5 LPM), 1/4" OD connection.
• TFP-GV09Gas turbine flow meter, range 4.2 to 21 SCFH (2 to 10 LPM), 1/4" OD connection.
• TFP-GV10Gas turbine flow meter, range 8.5 to 42 SCFH (4 to 20 LPM), 3/8" OD connection.
• TFP-GV11Gas turbine flow meter, range 21 to 110 SCFH (10 to 50 LPM), 3/8" OD connection.
• TFP-GV12Gas turbine flow meter, range 42 to 210 SCFH (20 to 100 LPM), 1/2" OD connection.
• TFP-GV13Gas turbine flow meter, range 85 to 420 SCFH (40 to 200 LPM), 1/2" OD connection.

Specifications

• Service:Clean dry gases compatible with wetted materials.
• Wetted Materials:PPS, acetal, sapphire, glass, epoxy, and fluoroelastomer.
• Accuracy:3% of FS.
• Linearity:3% of FS.
• Repeatability:0.5% of FS.
• Temperature Limits:41 to 131F (5 to 55C); Storage: 32 to 158F (0 to 70C); Sensitivity: 0.2% of FS per C.
• Pressure Limits:40 psig (2.8 bar).
• Process Connection:Compression fitting, see model table on Catalog page.
• Power Requirements:11.5 to 15 VDC.
• Power Consumption:35 mA @ 12 VDC.
• Output Signal:0 to 5 VDC; minimum 2.5 k load.
• Electrical Connections:Four-pin power and signal connector. A power adapter or mating cable required for operation. See accessories table.
• Enclosure Rating:IP10 (NEMA 1).
• Weight:0.16 lb (75 g).
• Agency Approvals:CE.

Features

• Corrosion resistant PPS body
• High repeatability with patented microturbine design
• Design accurately measures flow rates with no zero drift and no required maintenance

Accessories

Model NumberDescription

• A-454115 VAC power adapter and signal cable.
• A-455230 VAC power adapter and signal cable.
• A-45636" mating cable with spliced leads.

Dwyer Air Velocity Transmitter

Series 641RM Air Velocity Transmitter with Remote Probe

For Remotely Mounting Electronic Enclosure

The SERIES 641RM features the same highly accurate heated mass flow sensor as the Series 641, with a remote probe construction. The units 6 cable which connects the sensing probe with the electronic enclosure allows the enclosure to be mounted where it can be more easily accessed.

Product Applications

• Exhaust stack flow monitoring
• Air control in drying processes
• HVAC air velocity measurements
• Fan supply and exhaust tracking
• Clean room ventilation monitoring

ModelDescription

• 641RM-12Air velocity transmitter, without LED display.
• 641RM-12-LEDAir velocity transmitter, with LED display.

Dwyer Air Velocity Transmitter

Series 641RM Air Velocity Transmitter with Remote Probe

For Remotely Mounting Electronic Enclosure

The SERIES 641RM features the same highly accurate heated mass flow sensor as the Series 641, with a remote probe construction. The units 6 cable which connects the sensing probe with the electronic enclosure allows the enclosure to be mounted where it can be more easily accessed.

Product Applications

Exhaust stack flow monitoring

Air control in drying processes

HVAC air velocity measurements

Fan supply and exhaust tracking

Clean room ventilation monitoring

ModelDescription

641RM-12Air velocity transmitter, without LED display.

641RM-12-LEDAir velocity transmitter, with LED display.

Specifications

• Service:Clean air and compatible, non-combustible gases.
• Accuracy:3% FS Process gas: 32 to 122F (0 to 50C); 4% FS Process gas: -40 to 32F & 122 to 212F (-40 to 0C & 50 to 100C).
• Response Time:Flow: 1.5 s to 95% of final value (output filter set to min.).
• Temperature Limits:Process: -40 to 212F (-40 to 100C). Ambient: 32 to 140F (0 to 60C).
• Pressure Limit:100 psi (6.89 bar) maximum.
• Humidity Limit:Non-Condensing.
• Power Requirements:12 to 35 VDC, 10 to 16 VAC. 1.5 A rating required on supply due to initial power surge drawn by transmitter.
• Output Signal:4 to 20 mA, isolated 24 V source, 3 or 4-wire connection.
• Output Filter:Selectable 0.5-15 s.
• Loop Resistance:600 max.
• Current Consumption:300 mA max.
• Electrical Connections:Screw terminal.
• Mounting Orientation:Unit not position sensitive. Probe must be aligned with airflow.
• Weight:13.2 oz (374.26 g).
• Cable Length:6' (1.82 m).
• Probe Length:12" (30.48 cm) standard.
• Probe Diameter:5/16" (0.79 cm).
• OPTIONAL DISPLAY VERSION:
• Display:4-1/2 digit 1/2" red LED.
• Resolution:1 FPM, 0.01 MPS (10 FPM @ 10, 000 and 15, 000 FPM ranges).
• Weight:13.9 oz (394.16 g).

ultrasonic energy meter

series tuf ultrasonic energy meter

energy monitoring capability, no moving parts, compact and light weight

the series tuf ultrasonic energy meter is a highly accurate and stable energy meter that utilizes ultrasonic technology to measure heating and cooling energy consumption. The series tuf is a compact meter with a flowmeter and energy calculator in one, making it great for installation on chillers and boilers.

instructions for ordering

• choose 1 ultrasonic energy meter model (includes 2 bspp pipe fittings, 2 tightening nuts, 2 o-rings, and 1 thermowell with welding collar)
• choose 1 pipe fitting model given the appropriate fitting size if npt or bspt connections are required (for dn15 to dn40 only)*
• example: tuf-150-md, fitting size: a, select pipe fitting model wm-acc-c01 or wm-acc-c11.

product applications

• heat metering
• utilities billing
• tenant billing
• monitoring of water heating or cooling: radiators, fan coils

modeldescription

• tuf-1000-bntenant ultrasonic btu flowmeter, dn100 pipe size and 60 m3/h permanent flow rate with bacnet communication.
• tuf-1250-bntenant ultrasonic btu flowmeter, dn125 pipe size and 100 m3/h permanent flow rate with bacnet communication.
• tuf-1500-bntenant ultrasonic btu flowmeter, dn150 pipe size and 150 m3/h permanent flow rate with bacnet communication.
• tuf-150-bntenant ultrasonic btu flowmeter, dn15 pipe size and 1.5 m3/h permanent flow rate with bacnet communication.
• tuf-2000-bntenant ultrasonic btu flowmeter, dn200 pipe size and 200 m3/h permanent flow rate with bacnet communication.
• tuf-200-bntenant ultrasonic btu flowmeter, dn20 pipe size and 2.5 m3/h permanent flow rate with bacnet communication.
• tuf-250-bntenant ultrasonic btu flowmeter, dn25 pipe size and 3.5 m3/h permanent flow rate with bacnet communication.
• tuf-250-mdtenant ultrasonic btu flowmeter, dn25 pipe size and 3.5 m3/h permanent flow rate with modbus communication.
• tuf-320-bntenant ultrasonic btu flowmeter, dn32 pipe size and 6.0 m3/h permanent flow rate with bacnet communication.
• tuf-400-bntenant ultrasonic btu flowmeter, dn40 pipe size and 10 m3/h permanent flow rate with bacnet communication.
• tuf-400-mdtenant ultrasonic btu flowmeter, dn40 pipe size and 10 m3/h permanent flow rate with modbus communication.
• tuf-500-bntenant ultrasonic btu flowmeter, dn50 pipe size and 15 m3/h permanent flow rate with bacnet communication.
• tuf-650-bntenant ultrasonic btu flowmeter, dn65 pipe size and 25 m3/h permanent flow rate with bacnet communication.
• tuf-800-bntenant ultrasonic btu flowmeter, dn80 pipe size and 40 m3/h permanent flow rate with bacnet communication.

features

• lower maintenance costs with local parameter display and no moving parts
• serial communication output allows for easy transfer of data
• flow and temperature monitor in one unit eliminates the need for multiple units

metal electronic totalizing meter

the series ttms 316 ss electronic totalizing meters offer batch and cumulative flow totals in a stainless steel construction for 1/2" to 2" pipe sizes with iso, npt, or sanitary fitting connections.

features:

• compact modular design ideal for easy portability
• easily alternate display from flow rate, batch or cumulative totals in one low cost un
• easy to read lcd display provides instantaneous local indicatio
• included batteries featuring a 5 year life span with no added cos
• immediate push button, field calibration eliminates downtim

specification:

• service : compatible fluids.
• flow range : 1/2": 1 to 10 gpm (3.8 to 37.9 lpm); 3/4": 2 to 20 gpm (7.6 to 75.7 lpm); 1": 5 to 50 gpm (18.9 to 190 lpm); 1-1/2": 10 to 100 gpm (38 to 380 lpm); 2": 20 to 200 gpm (76 to 760 lpm).
• wetted materials : bearings: ceramic; shaft: tungsten carbide; rotor: pvdf; rings: 316 ss; body: ss.
• connections: iso, npt or sanitary fitting options : iso, npt or sanitary fitting options.
• power requirements : (2) 3v lithium, installed functional, user replaceable.
• weight : 1/2": 2.36 lb (1.07 kg); 3/4": 2.74 lb (1.24 kg); 1": 4.00 lb (1.81 kg); 1-1/2": 4.76 lb (2.16 kg); 2": 6.52 lb (2.96 kg).

applications:

• chemical batching
• petrochemical
• food & beverage liquid flow monitoring
• municipal water monitoring

other details:

modeldimension in mm

• aa1bcd
• ttms-1rx-x4-5/32 [105.66]5 [127.00]1-31/64 [37.59]3-7/16 [87.38]2-11/64 [55.12]
• ttms-2rx-x4-1/4 [107.95]5 [127.00]1-19/32 [40.39]3-7/16 [87.38]2-11/64 [55.12]
• ttms-3rx-x4-1/2 [114.30]5-1/2 [139.70]1-51/64 [45.72]3-7/16 [87.38]2-11/64 [55.12]
• ttms-4rx-x5-1/4 [133.35]6-1/2 [165.10]2 [50.80]3-7/16 [87.38]2-11/64 [55.12]
• ttms-5rx-x6-1/4 [158.75]7 [177.80]2-7/32 [56.39]3-7/16 [87.38]2-11/64 [55.12

.

gas mass flow meter

series gfm2 gas mass flow meter

1% fs, programmable relays

the series gfm2 gas mass flow meter is an ideal choice for the measurement of flow rates of a wide variety of gases. Unit can be calibrated for a variety of gases with user selectable 0 to 5 vdc or 4 to 20 ma and two relay outputs and programmable totalizer that indicates total gas quantity.

product applications

• gas flow measurement
• gas glow control
• operating pumps and valves
• process equipment
• vacuum processes
• glass and metal coating
• film deposition

specifications

• service:clean gases compatible with wetted parts.
• wetted materials:>gfm2-x-x-a: anodized aluminum, brass, 316 ss fluoroelastomer o-rings;
• gfm2-x-x-s: 316 ss, and fluoroelastomer o-rings; buna-n, epr and ptfe o-rings optional.
• accuracy:1% fs.
• repeatability:0.25% fs.
• response time:2 seconds to within 2% of actual flow.
• output signal:linear 0 to 5 vdc (3000 min. Load impedance) and 4 to 20 ma (500 max. Loop resistance).
• relay rating:1 a @ 24 vdc.
• max. Particulate size:5 microns.
• temperature limits:32 to 122f (0 to 50c).
• power supply:11 to 26 vdc.
• process connections:1/8" compression fitting for flow rates 10 l/min; 1/4" for 50 l/min; 3/8" for 100 l/min.
• display:2 x 16 character lcd (optional).
• pressure limits:500 psig (34.5 bar).
• leak integrity:1 x 10-9 sml/sec of helium.
• weight:1.05 lb (0.48 kg).

features

• utilizes a straight tube sensor with a restrictor flow element to provide a high 1% fs accuracy and 0.25% fs repeatability
• gas flow can be displayed in 23 different engineering units on an optional 2x16 character lcd display with internal conversion factors for up to 32 gases
• digital rs-232 or rs-485 interfaces allow for easy communication and for multi-drop capability of up to 256 units (rs-485 only)
• user-friendly interface allows for the programming of high and low gas flow alarms, along with two user-programmable electromechanical spdt relays with latch options
• stores calibration information for up to 10 different gases, internal or user-specific k-factors
• automatic sensor zero offset adjustment (via digital interface or local push button)
• nist traceable certificate included
• self-diagnostic tests

accessories

model numberdescription

• a-110na12110 vac power supply, 12 vdc with communication interface branch

related products

• series gfm gas mass flow meter
• series gfm gas mass flow meter
• series gfm3 gas mass flow meter
• series gfm3 gas mass flow meter
• series gfm4 gas mass flow meter
• series gfm4 gas mass flow meter

WM2 Multi Jet Water Meter

Series WM2 Multi-Jet Water Meter

Economical, Brass Body, Dry Dial

The Series WM2 Multi-Jet Water Meters is a series of mechanical, water totalizing meters that display the total water usage in gallons or m3. They are available in a range of body sizes and include NPT or BSPT couplings.

Not for potable water use, brass contains lead in excess of low lead limits.

Product Applications

• Irrigation
• Cooling systems
• Filtration systems
• Water monitoring

ModelDescription

• WM2-A-C-015/8" x 1/2" brass multi-jet water meter (GPM).
• WM2-A-C-025/8" x 3/4" brass multi-jet water meter (GPM).
• WM2-A-C-033/4" brass multi-jet water meter (GPM).
• WM2-A-C-041" brass multi-jet water meter (GPM).
• WM2-A-C-061-1/2" brass multi-jet water meter (GPM).
• WM2-A-C-072" brass multi-jet water meter (GPM).
• WM2-B-C-0815mm brass multi-jet water meter (m3/h).
• WM2-B-C-1020mm brass multi-jet water meter (m3/h).
• WM2-B-C-1125mm brass multi-jet water meter (m3/h).
• WM2-B-C-1232mm brass multi-jet water meter (m3/h).
• WM2-B-C-1340mm brass multi-jet water meter (m3/h).
• WM2-B-C-1450mm brass multi-jet water meter (m3/h).

Specifications

• Service:Water.
• Wetted Materials:Body: Brass, polyethylene;
• Couplings: Brass;
• Measuring Chamber: Polyethylene, ABS plastic, ferrite, acetal.
• Flow Range:See model chart on catalog page.
• Accuracy:Transitional Flow: 5%; Nominal Flow: 2%.
• Temperature Limit:104F (40C).
• Pressure Limit:232 psi (16 bar).
• Totalizing Display Maximum:See model chart on catalog page.
• Mounting Orientation:Horizontal with the register face pointing up.
• Weight:See catalog page.

Features

• Multi-jet design allows for simplicity and accuracy with wide flow ranges, even in low flow applications
• Magnetically driven, hermetically sealed register does not leak or fog and is completely separated from the water
• Designed for long service life and maintenance-free operation, even under harsh conditions
• Integral strainer that protects meter from particulate damage
• Easy installation with included coupling adapters

Related Products

• Series WM Multi-Jet Water Meter
• Series WM Multi-Jet Water Meter
• Series WM2 Multi-Jet Water Meter
• Series WM2 Multi-Jet Water Meter
• Series WMT2 Multi-Jet Water Meter with Pulsed Output
• Series WMT2 Multi-Jet Water Meter with Pulsed Output
• Series WMH Multi-Jet Hot Water Meter
• Series WMH Multi-Jet Hot Water Meter
• Series WPT Multi-Jet Plastic Water Meter
• Series WPT Multi-Jet Plastic Water Meter
• Series WRBT Multi-Jet Water Meter with Removable Bottom
• Series WRBT Multi-Jet Water Meter with Removable Bottom

Liquid Turbine Flow Meter

Series TFM-LP Liquid Turbine Flow Meter

316SS Body, 0 to 5 VDC and Pulse Outputs

The SERIES TFM-LP Liquid Flowmeters utilize a turbine wheel and electro-optical detection to convert flow rates into a linear 0 to 5 VDC and pulsed output signal for recording and data logging. A power adapter or mating cable assembly is required for operation

Product Applications

• Industrial flow monitoring
• Commercial systems
• Laboratory equipment

ModelDescription

• TFM-LP03Liquid turbine flow meter, range .21 to 1.6 GPH (.013 to 0.1 LPM), 1/8" OD connection.
• TFM-LP04Liquid turbine flow meter, range .32 to 3.2 GPH (0.02 to 0.2 LPM), 1/4" OD connection.
• TFM-LP05Liquid turbine flow meter, range .79 to 7.9 GPH (0.05 to 0.5 LPM), 1/4" OD connection.
• TFM-LP06Liquid turbine flow meter, range 1.6 to 16 GPH (0.1 to 1 LPM), 1/4" OD connection.
• TFM-LP07Liquid turbine flow meter, range 3.2 to 32 GPH (0.2 to 2 LPM), 1/4" OD connection.
• TFM-LP08Liquid turbine flow meter, range 7.9 to 79 GPH (0.5 to 5 LPM), 3/8" OD connection.
• TFM-LP09Liquid turbine flow meter, range 16 to 160 GPH (1 to 10 LPM), 3/8" OD connection.

Specifications

• Service:Clean liquids compatible with wetted materials.
• Wetted Materials:316 SS, acetal, sapphire, glass, epoxy, and fluoroelastomer.
• Accuracy:1% of FS.
• Linearity:1% of FS.
• Repeatability:0.2% of FS.
• Temperature Limits:41 to 131F (5 to 55C); Storage: 32 to 158F (0 to 70C); Sensitivity: 0.2% of FS per C.
• Pressure Limits:500 psig (34.5 bar).
• Process Connection:Compression fitting, see model table on Catalog page.
• Power Requirements:11.5 to 15 VDC.
• Power Consumption:35 mA @ 12 VDC.
• Output Signal:0 to 5 VDC: Minimum 2.5 k load; Pulse: 7.5 VDC peak buffered square wave.
• Electrical Connections:Four-pin power and signal connector. A power adapter or mating cable required for operation. See accessories table.
• Enclosure Rating:IP10 (NEMA 1).
• Weight:0.86 lb (390 g).
• Agency Approvals:CE.

Features

• Rugged 316 SS body
• High repeatability with patented microturbine design
• Design accurately measures flow rates with no zero drift and no required maintenance

Accessories

Model NumberDescription

• A-454115 VAC power adapter and signal cable.
• A-455230 VAC power adapter and signal cable.
• A-45636" mating cable with spliced leads.

Orifice Plate Flowmeter

Series OP Orifice Plate Flowmeter

The Series OP Orifice Plate Flowmeter is a complete orifice plate flow metering package. It incorporates a stainless steel orifice plate with a unique holder or carrier ring containing metering taps and integral gaskets. It was designed for use wherever there is an application for a conventional flow orifice plate. It can also be used in place of other primary differential producers for efficiency and cost effectiveness. Installation is accomplished simply by slipping the unit between standard flanges (orifice flanges are not required). The Series OP is available in line sizes from 1/2" to 24" and can be used with compatible liquids and gases.

Features:

• Mounted with standard flanges
• Standard "corner tap" configuration
• Corrosion free material
• Simplified installation
• Built in metering taps (1/4" female NPT STD)
• Proven through a wide range of applications for accuracy and energy efficiency
• Assures long term reliability and accuracy
• Service : Compatible liquids and gases.
• Installation : Standard flange 125/150 rating.
• Pipe Requirements : General requirements 10 diameter upstream and 5 diameter downstream.

Applications:

• Fluid flow rates in building water lines
• Boiler feedwater
• Cooling water
• Combustion or compressed air
• Steam flow

Accuracy:

The Series OP utilizes the corner tap proportions as defined in ISO 5167. While this code may not be referred to as International Standard until accepted by the ISO Council, the ASME Fluid Meters Research Committee has suggested that the dimensionless coefficient equation developed by the International Standards Organization (ISO) and presented in ISO 5167 is significantly better for the broad spectrum of flow measurement applications throughout process industries.

The coefficient values used in the Series OP bore calculations represent the same confidence level assigned to the flange and radius taps widely accepted in fluid flow measurement.

The accuracy assigned to the coefficient values is 0.6% full scale flow for d/D (Beta) values 0.2 to 0.6 and 0.7% for Beta values 0.7 to 0.75 (i.e. of 0.7 would have an uncertainty value of 0.7% full scale flow).

Accuracy of the differential signal produced by the Series OP equals or exceeds that of a properly manufactured and installed flange or radius tap orifice meter.

Mounting:

The orifice metering primary shall be suitable for installation between standard ANSI 125/150# flanges (any material) mounted on standard pipe (any material). The unit shall be "self centering" within the bolt circle of the flanges. No alignment of the orifice shall be necessary unless used with 300# or non-standard flange ratings. Drilling and or tapping of the main or flanges will not be allowed or required. The overall laying length shall be 1.25 ?? including pre-attached ring type 1/8 ?? thick Buna "N" Gaskets.

Pipe Requirements:

Upstream and downstream pipe requirements are contingent upon two factors: (a) Beta Ratio-ratio of the orifice bore to the pipe I.D. (d/D); (b) The type of fitting or disturbance upstream of the Series OP. For most applications, 10 pipe dia. upstream & 5 dia. downstream are sufficient. (5 pipe dia. up and 2 dia. down are acceptable for non-critical application.)

compact ultrasonic flowmeter

model ufm compact ultrasonic flowmeter

cost effective, compact & adjustable design, non-invasive

model ufm compact ultrasonic flowmeter is a low cost clamp-on, ultrasonic flowmeter.the model ufm implements the transit-time difference to measure flow rates in pipes non-invasively. It is a compact and lightweight design, featuring an easily installed, all in one clamp-on unit. This unit can measure velocity and flow in pipes with outside diameters ranging from 0.98 to 4.62" (24.89 to 117.35 mm). The screen offers easy to read text with a convenient backlight for visual comfort.this model comes with a volume pulse and 4 to 20 ma flow rate output.

principles of operation

two sensors located in the guiderail are placed on the exterior of the pipe, and each transmits an ultrasonic pulse through the pipe and fluid to the other. The velocity of the liquid flowing through the pipes causes the pulse to accelerate or decelerate. The difference in the transit times of the two pulses is used to calculate the flow rate. The use of transit time allows the flowmeter to be unaffected by pressure or temperature changes.

product applications

• flow measurement for heat metering
• chilled water metering and monitoring
• potable water metering and monitoring
• process water metering and monitoring

modeldescription

• ufm-1compact ultrasonic flowmeter.

specifications

• service:clean water with 0.98 ft/s (> 0.3 m/s).
• power requirements:12 to 24 vdc or vac.
• power consumption:7 w max.
• temperature limits:process: 32 to 185f (0 to 85c);
• ambient: 32 to 122f (0 to 50c).
• outputs:analog: 1 opto-isolated: 4 to 20 ma; error current: 3.5 ma;
• load resistance: 620 o max;
• pulse: 1 opto-isolated mosfet relay, 500 ma max, 166 pps max, 200 hz max.
• enclosure rating:ip54.
• enclosure material:plastic polycarbonate.
• repeatability:0.5% of measured value.
• electrical connections:16.4' (5 m) cable.
• response time:< 1 s.
• weight:2.9 lb (1.315 kg).
• agency approvals:ce.
• additional specifications
• applicable pipe material:steel, copper, or plastic.
• pipe outside diameter:0.98 to 4.62" (24.89 to 117.35 mm).
• applicable pipe lining:none.
• pipe wall thickness:0.02 to 0.39" (0.5 to 10 mm).

features

• non-invasive pipe measurement
• simple installation with all necessary components included such as converter, sensor, cables and mounting accessories
• compact and lightweight design, featuring an easily installed, all in one clamp-on unit intended for homogeneous liquids that contain no air
• screen offers easy to read text displaying both flow rate and total with a convenient backlight for visual comfort
• kit includes:
• converter w/ adjustable guiderail
• set of 1.81 to 2.75" (46 to 70 mm)clamps
• set of 2 to 5" (51 to 127 mm) clamps
• set of small pipe adaptor circle clamps
• set of small pipe adaptor v clamps
• ultrasonic coupling grease

Venturi Flowmeter with Magnehelic Gage

Series VFLO Venturi Flowmeter with Magnehelic Gage

2.5% Accuracy, Dual Scale in SCFM & in w.c.

The Series VFLO Venturi Flowmeter with Magnehelic Gage is fabricated from aluminum and has a gradual Venturi profile to reduce pressure losses through the meter. Flowmeter can be used in a vertical or horizontal position just by rotating the Magnehelic gage. The Magnehelic gage provides a large, clear and accurate display of your differential pressure reading. Each meter is calibrated at standard atmospheric conditions. The dual scale reads in SCFM and in w.c. The meter is supplied with easy to read reference charts for various flow conditions. It is available in line sizes from 1" to 4" and can handle vacuum and pressure applications.

To place an order for the Venturi Flowmeter with Magnehelic Gage, see the Magnehelic Configurator.

Product Applications

• Filter monitoring
• Air velocity with Dwyer pitot tube
• Blower vacuum monitoringFan pressure indication
• Duct, room or building pressures
• Clean room positive pressure indication

ModelDescription

• Series VFLOTo place an order for the Venturi Flowmeter with Magnehelic Gage, see the Magnehelic Configurator

Specifications

• Service:Air and non-combustible, compatible gases.
• Wetted Materials:Aluminum, silicone, acrylic, polycarbonate, high carbon steel, low carbon steel, brass, paper, acrylic paint, enamel paint, alkyd coating, nickel plate, zinc plate, helsel FC, 300 series stainless steel, PTFE, Loctite AV sealant, commercial black rubber, neoprene, samarium cobalt, nickel alloy steel cover, beryllium copper.
• Housing:Die cast aluminum case and bezel, with acrylic cover. Exterior finish is coated gray to withstand 168 hour salt spray corrosion test.
• Accuracy:2.5% FS.
• Pressure Limits:-20" Hg to 15 psig (-0.677 bar to 1.034 bar); MP option: 35 psig (2.41 bar). For applications with high cycle rate within gage total pressure rating, next higher rating is recommended.
• Overpressure:Relief plug opens at approximately 25 psig (1.72 kPa).
• Temperature Limits:20 to 140F (-6.67 to 60C).
• Size:4" (101.6 mm) diameter dial face.
• Mounting Orientation:Diaphragm in vertical position. Consult factory for other position orientations.
• Process Connection:Female NPT of nominal line size. See Model Chart page.
• Weight:Gage only: 1 lb 2 oz (510 g), MP & HP 2 lb 2 oz (963 g); Venturi: see Model Chart page.

Features

• Gradual Venturi profile reduces pressure losses through meter helping to insure a more accurate measurement to meet measurement specifications
• Easy to read gage through undistorted plastic face permits viewing from far away
• Patented design provides quick response to pressure changes means no delay in assessing critical situations
• Durable and rugged housing and high-quality components combined provides longservice life and minimized down-time

Accessories

Model NumberDescription

• MVB-LM1Mini Brass Ball Valve, lever handle, 450 psi, 1/8"
• MVB-WM1Mini Brass Ball Valve, wedge handle, 450 psi, 1/8"
• MVB-TM1Mini Brass Ball Valve, tee handle, 450 psi, 1/8"

Series VTT Hot-Wire Air Velocity Transmitter

Series VTT Hot-Wire Air Velocity/Temperature Transmitter

Configurable Air Velocity Ranges, Available with 5 Digit Display

The Series VTT Hot-Wire Air Velocity and Temperature Transmitter provides a versatile unit for air velocity and temperature needs. The VTT offers five field-selectable ranges as well as operating in metric (ms, C) or English (fpm, F) units. The VTT can measure up to 30 ms (6000 fpm) and 50C (122F). The units are available with or without an LCD display which alternates between velocity and temperature. Series VTT can be ordered in duct mount or remote mount configurations with 4-20 mA or 0-10 V outputs. The VTT is a useful transmitter for many common HVAC applications.

Specifications

• Service:Clean air and compatible, non-combustible gases.
• Accuracy:Air Velocity: 3% of reading 60 fpm (0.3 m/s);
• Temperature: 0.5% of reading 0.6F (0.4C).Temperature Limits:Ambient and Process: 32 to 122F (0 to 50C) [see chart on Catalog page for temperature effects on range]; Storage: 14 to 158F (-10 to 70C).
• Power Supply:24 VAC/VDC (10%) 3-4 wires.
• Current Consumption:4-20 mA Output: 80 mA maximum; 0-10 V Output: 40 mA.
• Response Time:Air Velocity: 2 seconds to 1/e (63%) of final value; Temperature: 5 seconds to 1/e (63%) of final value.
• Maximum Loop Resistance:4-20 mA Output: 500 ; 0-10 V Output: 1 k.
• Display:5 digit; Resolution 1 fpm (0.1 m/s) 1.0F (0.1C). Alternates between velocity and temperature.
• Electrical Connection:Screw terminal block.
• Cable Length (Remote Probe):6.56 ft (2 m).
• Enclosure Rating:ABS rated NEMA 4X (IP65).
• Mounting:Can be mounted in any orientation. Probe must be aligned with airflow. Mounting accessory included.
• Weight:With Display: 0.32 lb (145 g); Without Display: 0.24 lb (110 g).
• Agency Approvals:CE.

Series 641 Air Velocity Transmitter

High Accuracy, Field Selectable Ranges

The SERIES 641 Air Velocity Transmitter is the ideal instrument for monitoring air flow. This transmitter uses a heated mass flow sensor which allows for precise velocity measurements at various flow rates and temperatures. The 641s 16 field selectable ranges provides it the versatility to be selected for several air flow applications. The optional LED produces a complete, low-cost solution for local indication of air flow.

Product Applications

• Exhaust stack flow monitoring
• Air control in drying processes
• HVAC air velocity measurementsFan supply and exhaust tracking
• Clean room fresh air supply
• Ensure proper lab hood exhaust flow rate

ModelDescription

• 641-12Air velocity transmitter, 12" (304.8 mm) probe length.
• 641-12-LEDAir velocity transmitter, 12" (304.8 mm) probe length, with LED display.
• 641-18Air velocity transmitter, 18" (457.2 mm) probe length.
• 641-18-LEDAir velocity transmitter, 18" (457.2 mm) probe length, with LED display.
• 641-24Air velocity transmitter, 24" (609.6 mm) probe length.
• 641-24-LEDAir velocity transmitter, 24" (609.6 mm) probe length, with LED display.
• 641-30Air velocity transmitter, 30" (762 mm) probe length.
• 641-30-LEDAir velocity transmitter, 30" (762 mm) probe length, with LED display.
• 641-36Air velocity transmitter, 36" (914 mm) probe length.
• 641-36-LEDAir velocity transmitter, 36" (914 mm) probe length, with LED display.
• 641-6Air velocity transmitter, 6" (152.4 mm) probe length.
• 641-6-LEDAir velocity transmitter, 6" (152.4 mm) probe length, with LED display.

Specifications

• Service:Clean air and compatible, non-combustible gases.
• Accuracy:3% FS Process gas: 32 to 122F (0 to 50C); 4% FS Process gas: -40 to 32F & 122 to 212F (-40 to 0C & 50 to 100C).
• Response Time:Flow: 1.5 s to 95% of final value (output filter set to min.).
• Temperature Limits:Process: -40 to 212F (-40 to 100C). Ambient: 32 to 140F (0 to 60C).
• Pressure Limit:100 psi (6.89 bar) maximum.
• Humidity Limit:Non-condensing.
• Power Requirements:12 to 35 VDC, 10 to 16 VAC. 1.5 A rating required on supply due to initial power surge drawn by transmitter.
• Output Signal:4 to 20 mA, isolated 24 V source, 3 or 4-wire connection.
• Output Filter:Selectable 0.5-15 s.
• Loop Resistance:600 max.
• Current Consumption:300 mA max.
• Electrical Connections:Screw terminal.
• Process Connections:1/2" male NPT.
• Enclosure Rating:Designed to meet NEMA 4X (IP66) for non LED models only.
• Mounting Orientation:Unit not position sensitive. Probe must be aligned with airflow.
• Weight:12.6 oz (357.2 g).
• Agency Approvals:CE.

Features

• Ranges from 250 FPM (1.25 MPS) to 15, 000 FPM (75 MPS)
• Optional bright LED display
• Easy push button set-up

series 160e ellipsoidal tip pitot tube

designed to meet iso standard 3966

the series 160e ellipsoidal tip pitot tube uses a precision crafted tip configuration, which allows air to pass smoothly with minimum turbulence for consistent, reliable readings. sliding depth indicators grip firmly to ensure uniform insertion when measuring traverses across ducts. total and static pressure taps are 1/4" (6 mm) and are permanently silver soldered to the connection block, making them leak-proof and durable.

product applications

• monitor or control air velocity or air flow when combined with differential pressure gage, switch, or transmitter

models & ordering

sort by

modeldescription

• 160e-00ellipsoidal tip pitot tube, 0.2 meter insertion length.
• 160e-01ellipsoidal tip pitot tube, 0.3 meter insertion length.
• 160e-02ellipsoidal tip pitot tube, 0.48 meter insertion length.
• 160e-03ellipsoidal tip pitot tube, 0.8 meter insertion length.
• 160e-04ellipsoidal tip pitot tube, 1.0 meter insertion length.
• 160e-05ellipsoidal tip pitot tube, 1.22 meter insertion length.
• 160e-06ellipsoidal tip pitot tube, 1.52 meter insertion length.
• 160e-uellipsoidal tip universal pitot tube, attaches to any length of 3/4" sch. 40 pipe.

features

• designed to meet iso standard 3966 commonly required in uk and europe
• ellipsoidal tip design for improved accuracy
• 304ss construction adds strength, resists corrosion
• adjustable depth indicators for fast, consistent traverses
• alignment indicator helps keep tip parallel to flow

model numberdescription

• a-160-casepitot tube carrying case.
• a-532air velocity calculator slide chart.

related products

• series ms magnesense differential pressure transmitter
• series ms magnesense differential pressure transmitter
• series flst duct mounted airflow measurement station
• series flst duct mounted airflow measurement station
• series adps/edps differential pressure switch
• series adps/edps differential pressure switch
• series stra duct mounted airflow measurement station
• series stra duct mounted airflow measurement station

digital process meter

series dpma lcd digital process meter

1/8 din, loop powered, large 3-1/2 digit display

the series dpma adjustable lcd digital panel meter offers a 3-1/2 digit, high contrast display for easy viewing in a standard 1/8 din package. This series can accept 4 to 20 ma, 0 to 5 vdc, or 0 to 10 vdc inputs with a wide bipolar span and zero adjustment. A 24 vdc power supply is required to illuminate the colored segments.

product applications

• display process values from pressure, humidity, temperature, voltage, current, watt, or power factor transmitters.

modeldescription

• dpma-401 lcd digital panel meter, loop powered 4 to 20 ma, amber segments.
• dpma-401plcd digital panel meter with power engineering units, loop powered 4 to 20 ma, amber segments.
• dpma-402lcd digital panel meter, loop powered 4 to 20 ma, red segments.
• dpma-402plcd digital panel meter with power engineering units, loop powered 4 to 20 ma, red segments.
• dpma-404 lcd digital panel meter, loop powered 4 to 20 ma, green segments.
• dpma-404plcd digital panel meter with power engineering units, loop powered 4 to 20 ma, green segments.
• dpma-501 lcd digital panel meter, voltage powered 12 vdc/24 vdc, amber segments.
• dpma-501plcd digital panel meter with power engineering units, voltage powered 12 vdc/24 vdc, amber segments.
• dpma-502 lcd digital panel meter, voltage powered 12 vdc/24 vdc, red segments.
• dpma-502plcd digital panel meter with power engineering units, voltage powered 12 vdc/24 vdc, red segments.
• dpma-504 lcd digital panel meter, voltage powered 12 vdc/24 vdc, green segments.
• dpma-504plcd digital panel meter with power engineering units, voltage powered 12 vdc/24 vdc, green segments.

specifications

• input:dpma-4xx(p): 4 to 20 ma; dpma-5xx(p): 0 to 200 mvdc, 0 to 5 vdc or 0 to 10 vdc.
• input impedance:dpma-4xx(p): 300 nominal; dpma-5xx(p):390k nominal.
• accuracy:(0.05% fs + 1 count).
• power supply:dpma-4xx(p): powered by control loop; dpma- 5xx(p): 12 vdc or 24 vdc.
• backlight power supply:24 vdc @ 35 ma typical.
• span and zero:adjustable. (1999 counts).
• display:3-1/2 digits, 7 segments, 1" (25.4 mm) h.
• decimal points:3-position, user selectable.
• engineering units:dpma-xxx: f, c, %, psi; dpma-xxxp:v, a, kw, pf.
• polarity:automatic, "-" displayed.
• operating temperature:32 to 122f (0 to 50c).
• storage temperature:-4 to 158f (-20 to 70c).
• mounting:snap-in panel mount or clamp (gasket included).
• connection:screw terminals.
• conversion rate:3 per second.
• warm-up:10 minutes typical.
• weight:4 oz (113.4 g).
• agency approvals:rohs.

features

• 1/8 din panel size
• 3-1/2 digit display with 1" (25 mm) segments
• colored segments available in black, red, amber, green, or blue
• jumper selectable engineering units and decimal point positions

model mst2-01 digital moisture meter

measures moisture, temperature and relative humidity

the model mst2-01 digital moisture meter is a high-accuracy instrument used for determining the moisture content in wood, bamboo, and other various materials. This unit also has the ability to measure ambient temperature and relative humidity. The large digital lcd makes measurements easy to read, while the hold function makes them easy to record. The mst2-01 includes a protective cap, two replacement pins, and one battery.

modeldescription

• mst2-01digital moisture meter.

specifications

• range:moisture: 2 to 70%; temperature: 14 to 122f (-10 to 50c); relative humidity: 10 to 90% rh.
• accuracy:moisture: 1%; temperature: 2f (1c); relative humidity: 5% rh.
• resolution:moisture: 0.5%;
• temperature: 0.1f/c; relative humidity: 0.1% rh.temperature limits:32 to 104f (0 to 40c).
• humidity limits:0 to 70% rh.
• size:5.75" x 1.5" x 0.75" (147 mm x 36 mm x 18 mm).
• display:3-digit lcd.
• power requirements:3 v cr2032 lithium metal battery, installed functional, user replaceable.
• weight:2.4 oz (68 g).

features

• measures ambient temperature and relative humidity.

accessories

model numberdescription

• mst2-rpreplacement pins, set of 2.

Series 641RM Air Velocity Transmitter with Cable

Series 641RM Air Velocity Transmitter with Remote Probe

For Remotely Mounting Electronic Enclosure

The SERIES 641RM features the same highly accurate heated mass flow sensor as the Series 641, with a remote probe construction. The units 6 cable which connects the sensing probe with the electronic enclosure allows the enclosure to be mounted where it can be more easily accessed.

Product Applications

• Exhaust stack flow monitoring
• Air control in drying processes
• HVAC air velocity measurements
• Fan supply and exhaust tracking
• Clean room ventilation monitoring

ModelDescription

• 641RM-12Air velocity transmitter, without LED display.
• 641RM-12-LEDAir velocity transmitter, with LED display.

Specifications

• Service:Clean air and compatible, non-combustible gases.
• Accuracy:3% FS Process gas: 32 to 122F (0 to 50C); 4% FS Process gas: -40 to 32F & 122 to 212F (-40 to 0C & 50 to 100C).
• Response Time:Flow: 1.5 s to 95% of final value (output filter set to min.).
• Temperature Limits:Process: -40 to 212F (-40 to 100C). Ambient: 32 to 140F (0 to 60C).
• Pressure Limit:100 psi (6.89 bar) maximum.
• Humidity Limit:Non-Condensing.
• Power Requirements:12 to 35 VDC, 10 to 16 VAC. 1.5 A rating required on supply due to initial power surge drawn by transmitter.
• Output Signal:4 to 20 mA, isolated 24 V source, 3 or 4-wire connection.
• Output Filter:Selectable 0.5-15 s.
• Loop Resistance:600 max.
• Current Consumption:300 mA max.
• Electrical Connections:Screw terminal.
• Mounting Orientation:Unit not position sensitive. Probe must be aligned with airflow.
• Weight:13.2 oz (374.26 g).
• Cable Length:6' (1.82 m).
• Probe Length:12" (30.48 cm) standard.
• Probe Diameter:5/16" (0.79 cm).
• OPTIONAL DISPLAY VERSION:
• Display:4-1/2 digit 1/2" red LED.
• Resolution:1 FPM, 0.01 MPS (10 FPM @ 10, 000 and 15, 000 FPM ranges).
• Weight:13.9 oz (394.16 g).

Features

• Ranges from 250 FPM (1.25 MPS) to 15, 000 FPM (75 MPS)
• Optional bright LED display
• Easy push button set-up
• Compact housing
• 4 to 20 mA output
• Digital filter for signal damping

Accessories

Model NumberDescription

• A-156Flange mounting plate with 1/2" female NPT.
• A-158Split flange.
• A-159Mounting gland with 1/2" male NPT.
• 641-LEDField-upgradeable LED.

Related Products

• Model VT120 Integral Vane Thermo-Anemometer
• Series AVU Air Velocity Transmitter
• Model VT-200 Vane Thermo-Anemometer
• Series 641 Air Velocity Transmitter
• Technical Reference Books
• Model 8904 Integral Vane Thermo-Anemometer
• Model 471B Thermo-Anemometer Test Instrument

PVC Electronic Totalizing Meter

Series TTMP PVC Electronic Totalizing Meter

THE SERIES TTMP PVC ELECTRONIC TOTALIZING METERS offer batch and cumulative flow totals in a PVC construction for 1/2" to 4" pipe sizes with spigot, NPT or flange connections.

Features:

• Compact modular design ideal for easy portability
• Easily alternate display from flow rate, batch or cumulative totals in one low cost unit
• Easy to read LCD display provides instantaneous local indication
• Included batteries featuring a 5 year life span with no added costs
• Immediate push button, field calibration eliminates downtime

Specification:

• Service : Compatible fluids.
• Flow Range : See flow chart on catalog page.
• Wetted Materials : 1/2 to 2": PVC housing, ceramic bearings, tungsten carbide shaft, PVDF rotor, 316 stainless steel rings; 3 to 4": PVC housing, PEEK bearings, 316 stainless steel shaft & thrust washers, Acetal rotor & nose cone, ferrite signal generator.
• Pressure Limits : 1/2" to 2": 225 psig (15 bar) @ 73F; 3" and 4": 135 psig (9.3 bar) @ 73F.
• Power Requirements : TTMP-XX1: (2) 3V primary lithium metal batteries, installed functional, user replaceable; TTMP-XX3 to TTMP-XX6: (1) 9V primary lithium metal battery, installed functional, user replaceable or 7V to 30V external power.
• Battery Life : TTMP-XX1: Approximately 5 years; TTMP-XX3 to TTMP-XX6: Approximately 4 years.

Applications:

• Irrigation
• Municipal water monitoring

Specifications

• Service:Compatible fluids.
• Flow Range:See flow chart on catalog page.
• Wetted Materials:1/2 to 2": PVC housing, ceramic bearings, tungsten carbide shaft, PVDF rotor, 316 stainless steel rings; 3 to 4": PVC housing, PEEK bearings, 316 stainless steel shaft & thrust washers, Acetal rotor & nose cone, ferrite signal generator.
• Accuracy:1/2" to 2": 3% of reading; 3" and 4": 2% of reading.
• Batch Total Maximum:999, 999.
• Cumulative Total Maximum:99, 999, 900.
• Temperature Limits:Process: 32 to 140F (0 to 60C); Storage: -40 to 158F (0 to 70C).
• Pressure Limits:1/2" to 2": 225 psig (15 bar) @ 73F; 3" and 4": 135 psig (9.3 bar) @ 73F.
• Display:6-digit LCD, 3/4" H.
• Process Connections:See model chart on catalog page.
• Power Requirements:TTMP-XX1: (2) 3V primary lithium metal batteries, installed functional, user replaceable; TTMP-XX3 to TTMP-XX6: (1) 9V primary lithium metal battery, installed functional, user replaceable or 7V to 30V external power.
• Battery Life:TTMP-XX1: Approximately 5 years; TTMP-XX3 to TTMP-XX6: Approximately 4 years.
• Weight:See weight chart on catalog page.
• Agency Approvals:CE.

Model 475-1-FM-AV Air Velocity Kit

Model 475-1-FM-AV Air Velocity Kit

Includes Digital Manometer, Pitot Tube, Accessories

Convenient all-in-one kit is small, light and easy to use. No set-up or leveling needed. Digital manometer reads from 0-20.00" w.c. with 0.5% F.S. accuracy and minor divisions to 0.01. Large 1/2" LCD readout is easy to see in poorly lighted areas and has "low battery" warning. Included is a 6" stainless steel Pitot tube with integral compression fitting to hold it securely when taking readings. Also, two static pressure tips with magnetic mounting measure pressure drop across filters, condenser coils, etc. Kit comes complete with rubber tubing, 9V battery, step drill, AV calculator slide rule, and custom fitted carrying case. An indispensable test kit for the plant engineer, industrial hygienist and HVAC technician.

Complete Kit Includes:

• Series 475 Handheld Digital Manometer (0.5% FS accuracy and minor divisions to 0.01, large 1/2" LCD readout is easy to see in poorly lighted areas and has low battery warning)
• Model 166-6-CF, 6" SS pitot tube with integral compression fitting to hold it securely when taking readings
• Two No. A-303 Static Pressure Tips with Magnetic Mounting
• Two 4-1/2 Ft. Lengths 3/16" I.D. Rubber Tubing
• No. A-397 Step Drill for 3/16" - 1/2" Holes in 1/16" Increments
• No. A-532 AV Slide Chart
• 9 V Alkaline Battery
• Fitted Polyethylene Case

Click HERE to order the 475-1-FM-AV-NIST with a NIST calibration certificate through our Product Configurator.

ModelDescription

• 475-1-FM-AVAir velocity kit, range 0-20.00" w.c. (4.982 kPa), max. pressure 10 psig, kit includes static pressure tips, rubber tubing, Pitot tube, step drill, air velocity slide chart and carrying case.

Model NumberDescription

• A-303Portable static pressure tip, for 3/16" ID rubber or plastic tubing with 4" insertion.
• A-532Air velocity calculator slide chart.
• A-375Compression fitting connections, 1/8" tube to 1/8" NPT male.
• A-201Rubber latex tubing has less tendency to kink in storage and occupies less space, thus is best for portable work. 3/16" ID, 9' length.
• 166-6-CFPocket size Pitot tube, 1/8" dia., 6" insertion length, 3" tip, with 1/8" male NPT compression fitting.
• A-397Rugged step drill, quickly provides true round holes in thin materials, no center punch needed to start, automatically de-burrs drilled hole, high speed steel, drills 3/16" through 1/2" holes in 1/16" increments.
• A-463Plastic carrying case with foam liner for 475-1-AV air velocity kit - 13-1/2" x 10" x 2-3/8".
• A-402ACarrying case for most manometers; tough, gray nylon pouch, double zippered with belt loop
• A-47X-BOOTRubber boot for manometers (manometer not included).
• A-472AV Kit, less manometer

Related Products

• Series 641RM Air Velocity Transmitter with Remote Probe
• Model VT120 Integral Vane Thermo-Anemometer
• Series AVU Air Velocity Transmitter
• Model VT-200 Vane Thermo-Anemometer
• Series 641 Air Velocity Transmitter

model 485b thermo-hygrometer

measures % rh, temperature, dew point and wet bulb

the model 485b thermo-hygrometer is a versatile, compact, handheld instrument for measuring percentage of relative humidity and temperature in f or c. Dew point and wet bulb temperatures are derived from the relative humidity and temperature measurements and are displayed on the lcd.

for fast and accurate calibration services, click here!

product applications

• building commissioning
• pulp & paper

modeldescription

• 485b-1digital thermo-hygrometer includes 9v battery, sensing probe, wrist strap, soft carrying case and instructions

specifications

• service:humidity, temperature, wet bulb and dew point temperature detection in clean air.
• temperature limits:process: -40 to 176f (-40 to 80c); ambient: 5 to 125f (-15 to 51c).
• range relative humidity:0 to 100% (non-condensing).
• accuracy relative humidity:2% fs over 10 to 90% @ 77f (25c).
• range temperature:-20 to 140f (-28 to 60c).
• accuracy temperature:0.54f @ 72f (0.3c @ 25c).
• display:4.5 digit lcd.
• resolution:0.1%, 0.1 f/c.
• probe length:8" (203 mm) insertion.
• power requirements:9 v alkaline battery, included, user replaceable.
• weight:16 oz (454 g).
• agency approvals:ce.

features

• compatible with dwyer ap1 thermo-anemometer and vp1 100 mm vane thermoanemometer probes (sold separately)
• hold feature to freeze current readings on the display
• stores up to 99 readings for future evaluation

accessories

model numberdescription

• thermo hygrometer humidity & temperature probe with coiled cable.rp1thermo hygrometer humidity & temperature probe with coiled cable.
• rubber boot for manometers (manometer not included).a-47x-bootrubber boot for manometers (manometer not included).

related products

• model uhh-btg wireless mobile gateway
• model uhh-btg wireless mobile gateway
• mobile meter software test instrument app
• mobile meter software test instrument app

WRBT Multi Jet Water Meter

Series WRBT Multi-Jet Water Meter with Removable Bottom

Easy Clean Access, Lead Free

The Series WRBT Removable Bottom Multi-Jet Water Meters are a series of mechanical, water totalizing meters that display the total water usage in gallons with m3 options. They are available in a range of body sizes and include NPT or BSPT optional couplings. The ECO BRASS body incorporates a removable section that easily disassembles for easy cleaning of any collected debris that may collect in the system while maintaining its performance.

California Residents: Click Here for Proposition 65 WARNING.

Product Applications

• Agriculture
• Irrigation
• HVAC applications
• Measuring total condenser water flow in residential, commercial and industrial applications

ModelDescription

• WRBT-A-C-01-10Multi-jet water meter with removable bottom, 5/8" x 1/2" pipe size, 10 gal output.
• WRBT-A-C-02-10Multi-jet water meter with removable bottom, 5/8" x 3/4" pipe size, 10 gal output.
• WRBT-A-C-03-10Multi-jet water meter with removable bottom, 3/4" short length pipe size, 10 gal output.
• WRBT-A-C-04-10Multi-jet water meter with removable bottom, 3/4" pipe size, 10 gal output.
• WRBT-A-C-05-10Multi-jet water meter with removable bottom, 3/4" x 1" pipe size, 10 gal output.
• WRBT-A-C-06-10Multi-jet water meter with removable bottom, 1" long pipe size, 10 gal output.

Specifications

• Service:Water.
• Wetted Materials:Body: ECO BRASS; Couplings: ECO BRASS; Measuring Chamber: ABS Plastic.
• Flow Range:See model chart on catalog page.
• Accuracy:Transitional Flow: 3%; Nominal Flow: 1.5%.
• Temperature Limit:122F (50C).
• Pressure Limit:150 psi (10 bar).
• Totalizing Display Maximum:See model chart on catalog page.
• Output Signal:Pulse output with frequency proportional to flow rate.
• Pulse Options:10 gal or 100 gal per pulse. See model chart*.
• Electrical Rating:0.01 A @ 24 VAC/DC.
• Electrical Connections:Color-coded lead wires, 4.5' (1.5 m) long.
• Mounting Orientation:Horizontal with register facing up.
• Weight:See dimension chart.

Features

• Removable bottom allows for easy entry for cleaning
• Multi-jet design allows for simplicity and accuracy with wide flow ranges, even in low flow applications
• Magnetically driven, hermetically sealed register does not leak or fog and is completely separated from the water
• Designed for long service life and maintenance-free operation
• Integral strainer that protects meter from particulate damage
• Easy installation with included coupling adapters
• Pulsed output proportional to flow allows for remote flow totalization

Related Products

• Series WM2 Multi-Jet Water Meter
• Series WM2 Multi-Jet Water Meter
• Series WMT2 Multi-Jet Water Meter with Pulsed Output
• Series WMT2 Multi-Jet Water Meter with Pulsed Output
• Series WMH Multi-Jet Hot Water Meter
• Series WMH Multi-Jet Hot Water Meter
• Series WPT Multi-Jet Plastic Water Meter
• Series WPT Multi-Jet Plastic Water Meter

400 Air Velocity Meter

Displays Velocity and Air Pressure

The Series 400 Air Velocity Meter offers the convenience of a dual purpose instrument with high accuracy and easy-to-read scales. It can be used to balance air conditioning systems, measure pressure drop across filters, and test fan and blower discharge and inlet pressures. Series 400 kits include a manometer, Pitot tube, necessary tubing and connectors, red gage fluid, and carrying case.

Kit includes No. 400 Air Meter and all accessories:

Combination Inclined/Vertical Manometer. Dwyer Durablock precision machined solid acrylic plastic construction is virtually indestructible. Has both inclined section for high accuracy and vertical section for extended range. Pressure marked in black, Velocity in red figures. Easy to read - no reference tables needed. Has screw leveling adjustment and ground glass bubble level.

Click here, if you require a Safety Data Sheet for the Blue Gage Fluid or the Red Gage Fluid.

Product Applications

• Air balancing
• Building commissioning

ModelDescription

• 400-10-GAGEAir velocity meter, 0-10" w.c., 400-12600 FPM velocity, no Pitot tube.
• 400-10-KITAir velocity meter, 0-10" w.c., 400-12600 FPM velocity, 18" Pitot tube, metal carrying case.
• 400-23-GAGEAir velocity meter, 0-23" w.c., 400-19200 FPM velocity, no Pitot tube.
• 400-23-KITAir velocity meter, 0-23" w.c., 400-19200 FPM velocity, 18" Pitot tube, metal carrying case.
• 400-5-GAGEAir velocity meter, 0-5" w.c., 400-9000 FPM velocity, no Pitot tube.
• 400-5-L-KITAir velocity meter, 0-5" w.c., 400-9000 FPM velocity, 18" Pitot tube, metal carrying case.
• 400-5-S-KITAir velocity meter, 0-5" w.c., 400-9000 FPM velocity, 8" Pitot tube, metal carrying case.

Features

• Red figures display velocity in FPM and black figures display air pressure in inch w.c.
• No conversion tables needed for air at standard conditions
• Available with Pitot tubes and carrying case

Options

• Contact factory for extra long steel cases for use with longer Pitot tubes.

Accessories

Model NumberDescription

• A-1011 oz dispenser bottle of red gage fluid, .826 sp. gr.
• A-1024 oz bottle of red gage fluid, .826 sp. gr.
• A-1031 pt bottle of red gage fluid, .826 sp. gr.
• A-1041 qt bottle of red gage fluid, .826 sp. gr.
• A-1101 oz dispenser bottle of blue gage fluid, 1.910 sp. gr.
• A-1111 pt bottle of blue gage fluid, 1.910 sp. gr.
• A-431Steel carrying case for air velocity meter, No. 400-5.
• A-433Steel carrying case for air velocity meter, No. 400-10.
• A-536Metric air velocity calculator slide chart.
• A-532Air velocity calculator slide chart.

series mst-01 digital moisture meter

measures moisture from 2 to 70% with high accuracy (1.5%)

specifications

• range:2 to 70% moisture content.
• accuracy:1.5% moisture content.
• temperature limits:32 to 104f (0 to 40c).
• humidity limits:0 to 70%.
• display:3-digit lcd.
• resolution:0.5%.
• power requirements:9 v alkaline battery, included, user replaceable.
• weight:4.1 oz (116 g).

model mw-1 pocket wind meter

measures wind speed and temperature, wide range

the model mw-1 pocket wind meter measures wind speed and temperature via the integral vane and thermo-anemometer sensor. Users can view readings on the four digit lcd with wind speed bar graph and select units for air velocity and temperature. The mw-1 also features automatic shut-off, detailed instruction manual, and protective plastic water resistant housing that floats.

product applications

• balancing applications
• energy audits
• hvac inspection

modeldescription

• mw-1hand-held, mini-vane thermo-anemometer.

specifications

• air velocity range:0 to 30 m/s, 0 to 5860 ft/min, 0 to 90 km/h, 0 to 65 mph, 0 to 55 knots.
• temperature/wind-chill ranges:14 to 113f (-10 to 45c).
• temperature resolution:0.36f (0.2c).
• accuracy:wind speed: 5% of reading. Temperature: 3.6f (2c).
• resolution:0.1 m/s, 19 ft/min, 0.3 km/h, 0.2 mph, 0.2 knots.
• sample time:1 reading per s.
• water-resistant:up to 3' (1 m).
• power requirements:(3) cr2032 or br1225 lithium metal battery, installed functional, user replaceable.
• auto-off:14 m. After last key is pressed.
• impeller:plastic, repl.
• case:plastic.
• display:2.32 x 2" (59 x 51 mm).
• weight:1.84 oz (52.1 g).
• agency approvals:ce.

features

• user selectable units to fit any requirement
• auto shut-off to conserve battery life
• water resistant plastic housing floats

accessories

model number description

• a-166replacement vane for mw-1.

related products

• model vt120 integral vane thermo-anemometer
• model vt120 integral vane thermo-anemometer
• model vt-200 vane thermo-anemometer
• model vt-200 vane thermo-anemometer
• model 8904 integral vane thermo-anemometer

series avu air velocity transmitter

ideal for building automation systems, 5% or 8% full scale accuracy

the seris avu air velocity transmitter is ideal for a wide range of hvac measurement and control applications, particularly in complete building control and energy management systems. The series avu transmitter operates by measuring the heat loss from one of the two sensing elements in the air stream, then calculating the air velocity. Units are virtually immune to drift due to the design of the sensing element, which makes the transmitter accurate over the whole air velocity range.

calibration option available under accessories.

product applications

• supply and exhaust fan tracking, clean room systems, air pollution studies and manufacturing, zone control in hvac systems

modeldescription

• avu-1-a-air velocity transmitter, range 0-785 fpm (0-4 m/s), 4-20 ma output.
• avu-1-v-air velocity transmitter, range 0-785 fpm (0-4 m/s), 0-10 vdc output.
• avu-2-a-air velocity transmitter, range 0-1575 fpm (0-8 m/s), 4-20 ma output.
• avu-2-v-air velocity transmitter, range 0-1575 fpm (0-8 m/s), 0-10 vdc output.
• avu-3-a-air velocity transmitter, range 0-3150 fpm (0-16 m/s), 4-20 ma output.
• avu-3-v-air velocity transmitter, range 0-3150 fpm (0-16 m/s), 0-10 vdc output.
• avub-1-v-air velocity transmitter, 0-785 fpm (0-4 m/s) with 0-10 vdc output.
• avub-2-v-air velocity transmitter, 0-1575 fpm (0-8 m/s) with 0-10 vdc output.
• avub-3-v-air velocity transmitter, 0-3150 fpm (0-16 m/s) with 0-10 vdc output.

specifications

• service:clean air and compatible, non-combustible gases.
• accuracy:avu: 5% of fs; avub: 8% of fs.
• response time (90%):5 sec (typical).
• temperature limits:32 to 122f (0 to 50c).
• humidity limit:0-90% rh, non-condensing.
• power requirements:-a models 24 vdc +10%-15%;-v models 24 vdc or 24 vac +10% - 15%.
• output signal:-a models 4 to 20 ma current loop;-v models 0 to 10 vdc.
• loop resistance:(-a models ) 700 .
• current consumption:60 ma + output current
• maximum start up current:85 ma; 10 v
• output current limit:(-v models) >10 ma
• electrical connections:screw terminal. Cable gland for 4-8 mm wire (16 gage wire)
• enclosure rating:nema 6 (ip67) except sensing point.
• probe dimensions:9.45 x .75" (240 x 19 mm)
• mounting orientation:unit not position sensitive. Probe must be aligned with airflow
• weight:8.8 oz (250 g).
• agency approvals:ce

features

• 4 to 20 ma or 0 to 10 v output versions, nema 6 (ip67) enclosure rating, ac or dc powered (loop version dc only), 5% or 8% accuracy

model numberdescription

• nistcal-av1nist traceable calibration certificate for air velocity thermal anemometer meters. note: equal certs will be charged per units purchased.

related products

series 641rm air velocity transmitter with remote probe, model vt120 integral vane thermo-anemometer, model vt-200 vane thermo-anemometer, technical reference books, model 8904 integral vane thermo-anemometer, model 471b thermo-anemometer test instrument

CM-2 Digital Clamp Meter

Model CM-2 Digital Clamp Meter with True RMS

Measures DC/AC Voltage, DC/AC Current, Resistance

Our compact, low cost Model CM-2 Digital Clamp Meter with True RMS is ideal for general electrical testing and troubleshooting. A few applications include HVAC, automotive, electricalpower, and environmental monitoring uses. The Model CM-2 measures DC and AC voltage to 600 V, DC and AC current to 400 A, and resistance to 40 M ohms. The digital clamp meter features datarange hold and auto range buttons to prevent the screen from updating when gathering values, as well as a zero function. The 3-34 digit LCD features automatic polarity, overload and low battery indication. The Model CM-2 is furnished with red and black test leads, batteries and a carrying case with belt loop

Specifications

• Over Voltage Category:CAT III 600 V.
• AC Voltage:0.1 mV to 600 V (1.0% + 3 dgt).
• DC Voltage:0.1 mV to 600 V (0.8% + 2 dgt).
• AC Current:10 mA to 400 A (2.0% + 10 dgt).
• DC Current:10 mA to 400 A (2.0% + 10 dgt).
• Resistance:0.1 to 40 M (1.0% + 3 digit).
• Continuity Test:Audible buzzer.
• Max Conductor Size:1.18" diameter (30 mm).
• Display:4000 counts plus decimal point.
• Sampling Rate:2 times per second.
• Power Requirements:(2) AAA alkaline batteries, included, user replaceable.
• Weight:8.64 oz (245 g).

Related Products

• Model CM-1 Digital Clamp Meter

model cm-1 digital clamp meter

model cm-1 digital clamp meter

measures dc/ac voltage, ac current, resistance, frequency

the compact, low cost model cm-1 digital clamp meter is ideal for general electrical testing and troubleshooting. A few applications include hvac, automotive, electrical/power, and environmental monitoring uses. The digital clamp meter measures dc and ac voltage to 600 v, ac current to 400 a, and resistance to 400 ohms. In addition to volts, amps and ohms, this meter includes a frequency test to 400 hz. The cm-1 also features data/range hold and auto range buttons to keep the screen from updating when gathering values. The 3-3/4 digit lcd features automatic polarity, overload and low battery indication. The model cm-1 is furnished with red and black test leads, batteries and carrying case with belt loop.

modeldescription

• cm-1digital clamp meter

specifications

• over voltage category:cat iii 600 v.
• ac voltage:0.1 v to 600 v (1.5% + 5 dgt).
• dc voltage:0.1 v to 600 v (1.0% + 3 dgt).
• ac current:0.1 a to 400 a (2.0% + 10 dgt).
• resistance:0.1 to 400 (1.0% + 5 dgt).
• continuity test:audible buzzer.
• max conductor size:1.18" diameter (30 mm).
• frequency:1 hz to 400 hz (0.8% + 3).
• display:4000 counts plus decimal point.
• sampling rate:2 times per second.
• power requirements:(2) aaa alkaline batteries, included, user replaceable.
• weight:9.88 oz (280 g).

cm-3 digital clamp meter

model cm-3 digital clamp meter with true rms, peak hold and min/max

measures dc/ac voltage, dc/ac current, energy, resistance

our compact, low cost model cm-3 digital clamp meter is ideal for general electrical testing and troubleshooting. A few applications include hvac, automotive, electricalpower, and environmental monitoring uses. The cm-3 measures dc and ac voltage to 600 v, ac current to 400 a, and resistance to 2000 ohms. The digital clamp meter features datarange hold and auto range buttons to prevent the screen from updating when gathering values, as well as a zero function. Additional features include single and three phase energy measurement, minmax and average. The 3-34 digit backlit lcd features automatic polarity, overload, low battery indication and a bar graph. The model cm-3 is furnished with red and black test leads, batteries and a carrying case with belt loop.

specifications

• over voltage category:cat iii 600 v.
• ac voltage:0.1 v to 600 v (1.0% + 3 digit).
• dc voltage:0.1 v to 600 v (1.0% + 3 digit).
• ac current:0.1 a to 400 a (1.0% + 3 digit).
• resistance:0.1 to 2000 (1.0% + 5 digit).
• continuity test:audible buzzer.
• max conductor size:1.18" diameter (30 mm).
• frequency:40 hz to 400 hz (0.5%+1).
• active power range:0 to 1000 kw (3.5% + 3).
• display:backlit with bar graph. 10, 000 counts plus decimal point.
• power requirements:(2) aaa alkaline batteries, included, user replaceable.
• weight:9.88 oz (280 g).

related products

• model cm-1 digital clamp meter

Model 89088 Pocket Wind Meter

Measures Wind Speed, Wind Chill and Temperature

The Model 89088 measures wind speed, temperature and wind chill accurately with its rotating vane and thermo-anemometer sensor. The body and rotating vane are constructed of light weight, sturdy ABS plastic. The ABS impeller spins on a high precision jewel bearing allowing for maximum performance. Wind speed, maximum wind speed, temperature and wind chill can quickly be viewed on the LCD display in user selectable measuring units of degrees F or C, m/s, ft/min, Knots, MPH, K/hr and Beauforts. The 89088 also features a data hold button and a 5 minute automatic shut-off to conserve battery life. Accessories include a supplied battery and a cloth carrying pouch.

Model Description

• 89088Handheld miniature vane thermo-anemometer.

Specifications

• Air Velocity Range:1.1-20.0 m/s, 60-3937 ft/min, 0.4-38.8 knots, 0.8-72.0 k/hr, 0.5-44.7 mph, 1-8 beaufort.
• Wind Speed Limits:0.5-44.7 mph (60-3937) ft/min.
• Temperature/Wind Chill Limits:0 to 50C (32 to 122F).
• Accuracy:Velocity: 5% or last significant digit (whichever is greater); Temperature: 1C ( 2F).
• Resolution:Temperature: 0.1; Air Velocity: see Catalog page.
• Power Requirements:3 V CR2032 lithium metal battery, included, user replaceable.
• Battery Life:48 hour life under continuous usage. Auto-off: After 5 minutes.
• Materials:Impeller: ABS. Case: ABS.
• Display:28 (L) x 16 (W) mm.
• Weight:1.76 oz (50 g).
• Agency Approvals:CE.

Related Products

• Model VT120 Integral Vane Thermo-Anemometer
• Model VT120 Integral Vane Thermo-Anemometer
• Model VT-200 Vane Thermo-Anemometer
• Model VT-200 Vane Thermo-Anemometer
• Model MW-1 Pocket Wind Meter
• Model MW-1 Pocket Wind Meter

model emma digital multifunction environmental meter

monitor humidity, temperature, air velocity, sound and light

monitoring the environmental conditions is more convenient with the model emma multifunction meter. humidity, temperature, air velocity, air flow, sound and light measurements are combined in one easy to use instrument. the large, dual-line 4-digit lcd display shows both the current and average reading. for reading measurements in dimly lit areas, the display has a built-in back light. besides measuring the current and average reading, the model emma allows the user to read the minimum, maximum and differential measurement for each of the parameters. included with the meter is the carrying case, rubber boot, battery and tri-pod.

modeldescription

• emmamultifunction environmental meter.

specifications

• range:temperature: 14 to 140f (-10 to 60c); relative humidity: 0 to 100% rh; sound level: 30 to 130 db(a), 35 to 130 db(c); illumination: 0 to 50, 000 lux; wind speed: 96 to 5913 fpm; air flow: 0 to 999, 900 cfm (0.5 30 30 m/s).
• accuracy:temperature: 2.7f (1.5c); relative humidity: 3% rh (20 to 80% @ 25c); sound level: 1.5 db; illumination: 5% of reading + 10; wind speed: 3% of reading + 10; air flow: 3% of reading + 10.
• display:dual line, 4-1/2 digit lcd display.
• temperature limits:14 to 140f (-10 to 60c).
• resolution:temperature: 0.1f/c; relative humidity: 0.1%; sound level: 0.1 db; illumination: 1 up to 2, 000 lux; 10 up to 20, 000 lux; 100 up to 50, 000 lux.
• power requirement:9 v alkaline battery, included, user replaceable.
• response time:500 msec.
• weight:15.5 oz (430 g).
• agency approvals:ce.

model aqh-20 handheld indoor air quality meter

measures co2, temperature and humidity

the model aqh-20 indoor air quality meter reduces the number of instruments a contractor has to carry by measuring the carbon dioxide concentration, air temperature, and humidity percentage in one device. A large backlit lcd display shows all three parameters simultaneously. The model aqh-20 can display dew point or wet bulb temperatures in place of the ambient temperature. Minimum, maximum, and average readings are easily accessible through the function buttons. By pressing the hold key, the current values are held so that they can be recorded. An audible alarm warns the user that the current ambient conditions are becoming hazardous. The model aqh-20 includes a hard carrying case and batteries.

product applications

• building commissioning
• green house monitoring

modeldescription

• aqh-20handheld indoor air quality meter.

specifications

• ranges:co2: 0 to 2000; temperature: 14 to 140f (-10 to 60c); relative humidity: 0.0 to 99.9% rh.
• accuracy:co2: 30 ppm 5% of reading; temperature: 0.9f (0.6c); humidity: 3% rh (10 to 90%), 5% (0.0 to 9.9% or 90 to 99.9%).
• resolution:co2: 1 ppm; temperature: 0.1f (0.1c); humidity: 0.1% rh.
• response time:co2: < 30 s.; temperature: < 2 m.; humidity: < 10 m.
• display:4 digits for temperature/co2 and 3 digits for humidity.
• co2 sensor:non-dispersive infrared.
• temperature limits:32 to 122f (0 to 50c).
• humidity limits (non-condensing):0 to 95% rh.
• power requirements:(4) 1.5 v aa alkaline batteries, included, user replaceable.
• warm up time:30 s.
• weight:6.76 oz (200 g).
• agency approvals:ce.

features

• all-in-one unit for carbon dioxide, temperature, and humidity
• large backlit lcd for visibility in dark areas
• user configurable alarms for audible indication of hazardous conditions

accessories

model numberdescription

• th-cal33% and 75% salt bath calibration standards.

1227 dual range flex-tube u-inclined manometer

series 1227 dual range flex-tube u-inclined manometer

0.2" minor scale divisions, accuracy +/- 0.1" w.c.

use series 1227 as a regular u-tube manometer to read high-range pressure on the right leg, or as an inclined manometer to read low-range pressure on the bottom leg. Simply incline manometer until fluid levels read zero. No spirit level required. Magnetic clips hold the gage in position on a steel duct surface.

most versatile and useful low cost manometer we know of. Designed for installation and servicemen. A sturdy, clear plastic manometer, it offers single, direct readings in two ranges: as a u-tube, it reads from 0 to 16" of water; as an inclined gage, it reads from -.20 to 0 to 2.6" of water. Model 1227m (metric) is 0 to 400 mm water column as a u-tube and -5 to 0 to 70 mm water column as an inclined gage. "how-to-use" instructions are printed directly on the scale.

click here, if you require a safety data sheet for the red gage fluid.

california residents: click here for proposition 65 warning.

product applications

• fan status

• filter monitoring

modeldescription

• 1227dual range u-inclined manometer, 0-16" w.c. Vertical, .20-0-2.6" inclined. (english units)
• 1227mdual range u-inclined manometer, 0-400 mm vertical, -5-0-70 mm inclined. (metric units)

features

• reads 0 to 16 in w.c. As a u-tube and -0.20 to 0 to 2.6 in w.c. As an inclined gage
• clear, shatterproof indicating tube provides overpressure protection
• black markings on a stark white scale for positive definition

model numberdescription

• a-1011 oz dispenser bottle of red gage fluid, .826 sp. Gr.
• a-1024 oz bottle of red gage fluid, .826 sp. Gr.
• a-1031 pt bottle of red gage fluid, .826 sp. Gr.
• a-1041 qt bottle of red gage fluid, .826 sp. Gr.
• 1227-ccvinyl carrying case for the 1227 manometer.
• a-356gage plug with retainer loop, polyethylene plastic, for 1/4" id tubing, slip loop over tubing od and insert plug for seal.
• a-319flexible red pvc connector, 3/16" id rubber tubing to 1/4" id plastic tube for 1221, 1222 and 1227 manometers.
• a-344terminal tube, brass, 1/4" diameter tube, 8" length.
• a-339adapter, brass, 1/8" npt to 3/16" rubber and 1/8" id plastic tubing.
• a-220clear flexible vinyl tubing is easily inspected, and is therefore best for test applications where a possibility of fluid entering the tubing exists. 3/16" id x 5/16" od, lengths to 500'; 45 psi maximum pressure @ 73f.
• a-357thermometer and terminal tube holder, stainless steel wire.
• a-364magnet assembly for 1222 manometers, 2 required (3 required for 1222-36 and m-1000).

related products

• series 2000 magnehelic differential pressure gages
• series 2000 magnehelic differential pressure gages
• series 2-5000 minihelic ii differential pressure gage
• series 2-5000 minihelic ii differential pressure gage
• series 475 intrinsically safe handheld digital manometer
• series 475 intrinsically safe handheld digital manometer
• series 476a single pressure & series 478a digital manometer
• series 476a single pressure & series 478a digital manometer

Model 450A-1 Digital Pocket Size Carbon Monoxide Meter

Measures Up To 999 ppm, Audible Alarm

TheModel 450A-1 Digital Pocket Size Carbon Monoxide Metermeasures the ambient concentration of carbon monoxide (CO) in the environment and displays the measurement on the two line digital LCD screen. Besides the measurement, the maximum recorded CO value since the last reset is shown. An audible carbon monoxide alarm gives warning of CO levels above 25 ppm. For viewing in poorly lit environments, the built-in backlight brightens the display. Model 450A includes soft carrying case with belt loop, wrist strap, and batteries.

ModelDescription

• 450A-1Digital pocket size carbon monoxide meter.

Specifications

• Range:0 to 999 ppm.
• Accuracy (at 20 5C, 50 20% RH):20% @ 0 to 100 ppm; 15% @ 100 to 500 ppm.
• Resolution:1 ppm.
• Display:Dual digital LCD display.
• Response Time:Less than 60 seconds.
• Sensor:Electrochemical carbon monoxide sensor.
• Temperature Limits:-10 to 60C (14 to 140F).
• Humidity Limits (Non-Condensing):5 to 99% RH.
• Power Requirements:(3) 1.5 V AAA alkaline batteries, included, user replaceable.
• Battery Life:250 hours with backlight off; 35 hours with backlight on.
• Weight:4.23 oz (120 g).
• Alarms:Audible, preset at 25 ppm.
• Agency Approval:CE.

1223 flex-tube u-tube manometer

series 1221/1222/1223 flex-tube u-tube manometer

suitable for pressures up to 100 psi, better precision

these inexpensive manometers measure positive, negative and differential pressures. Dwyer flex-tube u-tube manometers combine the inherent accuracy of the simple "u" tube with the durability of tough, long-lasting plastic construction. Columns are of .375" o.d. Flexible and shatter proof clear butyrate tubing. They are easily accessible for cleaning. Indicating tube is backed by white scale channel to provide maximum color contrast. Scales are extruded high impact polystyrene plastic, formed to hold columns in perfect alignment. Stark white scales have graduations and numbers silkscreen-printed in black for maximum legibility.

you can choose from numerous models and features including over-pressure safety traps, in full scale ranges from 8" to 36" of water or mercury. All are suitable for total pressures to 100 psi - for determining velocity and static pressures, leakage, fan and blower efficiency, filter resistance, and gas pressures. Ideal wherever a portable, direct reading manometer is needed. Standard ranges and markings as shown, or special ranges, colors, logos and brand names for oem quantity orders are available.

click here, if you require a material safety data sheet for the fluorescein green concentrate or the red gage fluid.

product applications

duct static pressure, calibration labs, filter monitoring

features

• minor divisions of 1/10" water column (or 2mm water column on metric units) are silkscreened in jet black on stark white scale for positive definition. Easy to read, even at a distance, they are acrylic coated for permanence. All models are furnished with one 3/4 ounce bottle of fluorescein green color concentrate with special wetting agent for w/m models, or 3/4 ounce bottle of red gage fluid for "d" units.
• series 1221 manometer - our simplest, lowest cost basic u-gage. A dependable u-tube manometer that withstands hard use and provides accurate, high visibility readings. For use with water, mercury or red gage fluid. For mercury filled manometers, a scale clamp bar, dwyer part no. A-363 (available as an extra for series 1221 - and standard on series 1222) is recommended. One pair of carrying plugs and a pair of non-kink vinyl tube connectors are included with each manometer.
• series 1222 manometer - all the features of the 1221 plus magnetic clips for mounting to any vertical steel surface, and clamp bar to insure against u-tube slipping. (especially recommended for manometers used with mercury.) both magnets are easily removed and replaced at the user's convenience.
• series 1223 manometer - our finest u-gage - for either portable or stationary use. Safety traps prevent loss of indicating fluid in case of accidental over-pressure. Tubing is permanently bonded to a molded, high impact acrylic plastic top that contains safety traps. Large magnetic clips and clamp bar are provided. Standard type "a" connections include two rapid shut-off type molded nylon tubing connections, two 3' lengths of flexible tygon plastic tubing, and two 1/8" pipe thread to tube adapters.

460 Air Meter

Model 460 Air Meter/Draft Gage

A Low-Cost, Direct Reading Instrument Used for Both Air Velocity & Static Pressure Tests

Simple and quick, the 460 Air Meter is popular for servicing air conditioning, heating and ventilating equipment. Direct reading velocity and static pressure scales both low and high ranges show supply and return grille velocities, furnace draft, pressure drop across filters, etc. The 460 gives consistent, accurate results with no tedious calibration. Rugged plastic for rough daily use. Dual velocity ranges read 260-1200 and 1000-4000 FPM; pressure ranges from .005-.09 and .05 -1.0 in w.c.

Product Applications

Measuring grille velocities, furnace draft, and pressure drop across filters

ModelDescription

• 460Air meter, range .005-1.0" w.c. and 260-4000 FPM, with probes and carrying case.
• M460Air meter, range .02-2.5 CM water, 1-20 M/sec, with probes and carrying case.

Features

• High and low range velocity in one unit
• Simple and quick operation with highly accurate results
• Compact housing for easy portability

Model NumberDescription

• A-378Tube of 3 replacement floats for No. 460.
• A-379Supply grille probe for No. 460.
• A-380Return grille probe for No. 460.
• A-381Cleaning kit, including anti-static chemically treated pipe stem cleaner and nylon high range orifice cleaner for No. 460.
• A-532Air velocity calculator slide chart.
• A-201Rubber latex tubing has less tendency to kink in storage and occupies less space, thus is best for portable work. 3/16" ID, 9' length.
• 420534-00Bottom float support plug.
• 410027-00Carrying case only for Model 460 Air Meter.
• 420387-00Probe extension.

Model SM-100 Digital Sound Meter

Measures Noise Levels from 30 to 130 dB

Model SM-100 Digital Sound Meter is ideal for measuring noise levels from 30 to 130 dB with accuracy of 1.5 dB. Model SM-100 has a frequency of 31.5 Hz to 8 kHz, three different dB ranges, and a 1/2" condenser microphone. The SM-100 has two frequency weightings: the "A" weighting ranges from 30 to 130 dB, while the "C" weighting ranges from 35 to 130 dB. The four digit LCD backlit display has the ability to update in 0.5 seconds when the unit is set to fast response. Model SM-100 features data hold, ability to record maximum/minimum, auto ranging, auto power-off, and a dynamic range of 50 dB. The compact size of the SM-100 makes it very easy to operate and store. Each unit includes battery, carrying case, black foam cover to protect the sensor, and instruction manual. The SM-100 is ideal for technicians measuring and recording sound levels in zones or rooms of buildings, musical halls, theaters and near equipment or machinery on the plant floor.

ModelDescription

• SM-100Handheld digital sound meter.

Specifications

• Dynamic Range:50 dB.
• Measuring Level Range:A weighting: 30 to 130 dB; C weighting: 35 to 130 dB.
• Accuracy:1.5 dB (at 94 dB @ 1 kHz).
• Frequency Range:31.5 Hz to 8 kHz.
• Temperature Limits:Operating: 41 to 104F (5 to 40C); Storage: 14 to 140F (-10 to 60C).
• Humidity Limits:Operating: Below 80% RH; Storage: Below 70% RH.
• Elevation Limit:Maximum 6562 ft (2000 m) above sea level.
• Display:4 digit LCD with 0.5 second update when set to fast response.
• Resolution:0.1 dB.
• Power Requirement:9 V alkaline battery, included, user replaceable.
• Battery Life:50 hours with alkaline battery (approx).
• Weight:6 oz (170 g).
• Agency Approval:CE.