Delhi, India
Our Products
Features
Range of Experiments
Description
A steel disc 150 mm diameter and 20 mm thick is mounted on a shaft running in conical bearings housed on a substantial wall bracket. A mark on the flywheel and a pointer on the bracket enable the revolutions to be counted and timed with the stop watch supplied. A cord, load hanger and set of weights are provided.
This equipment is part of a range designed to both demonstrate and experimentally confirm basic engineering principles. Great care has been given to each item so as to provide wide experimental scope without unduly complicating or compromising the design. Each piece of apparatus is self-contained and compact. Setting up time is minimal, and all measurements are made with the simplest possible instrumentation, so that the student involvement is purely with the engineering principles being taught. A complete instruction manual is provided describing the apparatus, its application, experimental procedure and typical test results.
Complete, Filter Flask with Socket and buchner funnel with Sintered Disc of Porosity G-1 or G-2 or G-3 or G-4, having cone. Note: Please mention Porosity of Sintered Disc, while placing order.
|
For determining Stripping Value of bitumenous mixes having aggregate size 1.0mm to 75 microns.Salient Features
This apparatus is meant for determination of softening point of Bituminious materials according . Softening point is that temprature at which the speciman under test becomes soft enough to allow a steel ball of specific dimension to fall a required distance under test condition . The apparatus consists of glass beaker, ring stand two steel balls with ring and ball guides & hand stirrer.
Optional Accessories:
This is used for determining drop point of greases . It is an indication of the critical temperature of the solid or semi solid to the liquid state. The apparatus consists of brass sleeve and case with metal cup and a glass boiling tube with cork fitted to a bath (Beaker) is provided . A stirrer is also provided in the bath.
Drop Point Apparatus hand operated stirrer
Drop Point Apparatus with FHP Motorised stirrer and electrical heater with energy regulater control IP-31.
Drop Point Apparatus Same as above electric heated by concealed Hot plate.
Drop Point Apparatus Same as above electric heated by concealed Hot Plate.
Optional Accessories:
Thermometer 40C Low range.
Thermometer 41C High Range.
Thermometer 62C Drop Point Special.
Universal Heater
Spare Concealed Hot Plate.
This Apparatus determines melting point of petroleum products. it is made according .IT consists a rectangular block of aluminiium with built in electric heating element. The temperature is controlled by energy regulater .An adjustable lens is provided for viewing exact melting point supplied with capillaries.
Melting point Apparatus with energy regulater control Thermometer 63C.
Made in accordance with specifications , determination of distillation characterstic of Petroleum Products. The instrument consists of metal shield fitted with asbestos board to support distillation flask with GEARED height adustable device. It has slide for vapour tube and linning having glass window for Clear view of inside objects. The condenser bath is provided with Mild Steel black painted stand (without glasswares)electrically operated on 220 volts AC mains.
Used for detecting the presence of corrosive sulphur in petroleum products.The apparatus consists of a bath either dual purpose (500C & 1000C) or a boiling bath (1000C only) without stainless steel copper strips of definite size 6 or 18 test tubes can be accomodate in each type of bath with different temperature regulation system to operate on 220 volts AC. mains.
Made of stainless steel bath big enough to accomodate 3 cups Redwood No.1 and 2 cups of Redwood No.II. Stirring is done by a FHP electric motor in the bath. It is supplied complete with 5 Oil cups fitted with Precision jets of Stainless Steel. Temprature is controlled by Energy Regulator
Optinal Accessories For Red Wood Viscometer No. I, II & Multiple Red Wood Viscometer :
Used to determine the vapour pressure of volatile non-viscous Petroleum products except liquified petroleum gases. The Vapour pressure is made up of brass heavily Chronium plated and consists of an air chamber and a gasoline chamber of definite dimensions and volume ratio. A pressure gauge of required range is fitted above the air chamber. The joints are made leak proof by neoprene washers. The water bath used is of such dimensions that the vapour pressure bombs may be immersed to at least 1 inch above the air chamber and maintained at a constant temparature range upto 1000C plus minus 20C.
This is made as a specified the pour point is the lowest tempertaure at which the oil will just fail to flow. The apparatus consists of a main cooling bath made of stainless steel sheet and stand unit with drain plug and cover with provision for fitting thermometer and a filling aperture for adding freezing mixture. A glass jar for containing oils, jacket, disc and gasket as specifed are also provided.
It is used to determine the amount of carbon deposit when an oil is evaporated under specified condition.The Carbon residue values or crude oil , residue etc. are useful in the manufacture of various lubricants. The Apparatus consists of Spun Sheet Iron Crucible 25cc capacity, sheet iron hood and sheet iron block on a stand with triangular wire bridge.
| Funicular Polygon and Forces Apparatus Low cost, effective teaching Self-contained, bench mounted Direct measurement of forces Adjustable lines of action of forces Practical verification of triangle of forces, polygon of forces and link polygon Demonstrates equilibrium of forces at a point, applied to various points round adisc or acting on a rectangular lamina Concurrent & Non-concurrent coplanar forces Three year warranty Range of Experiments
Description This apparatus is a more comprehensive and versatile version of the HFC2. A simple but elegant demonstration of the conditions of equilibrium for three or more coplanar forces acting either at a point, on a circular disc or on a rectangular shape. Up to five loads can be applied to the chosen shape by setting up pulleys at various angular positions. The lines of action of the forces are recorded by drawing along the weighted cords onto a piece of paper attached to the pulley table. A range of experiments is possible, investigating concurrent and non concurrent coplanar forces acting on simple shapes, comparing the experimental values with the relevant polygons of force. This equipment is part of a range designed to both demonstrate and experimentally confirm basic engineering principles. Great care has been given to each item so as to provide wide experimental scope without unduly complicating or compromising the design. Each piece of apparatus is self-contained and compact. Setting up time is minimal, and all measurements are made with the simplest possible instrumentation, so that the student involvement is purely with the engineering principles being taught. A complete instruction manual is provided describing the apparatus, its application, experimental procedure and typical test results. |
This apparatus is used for penetration test on a wide variety of materials such as grease, Petroleum, Bitumen, Tar, Wax, Polish, food stuff, Rubber asphalts and pharmaceuticals Creams.A given force is applied over a given of a millimeter and expressed as penetration. It consists of a head support mounted on a vertical rod which can be adjusted for height. A rack and pinion and pointer assembly provides fine adjustment of a needle tip to sample and incorporates a slipping clutch mechanism which make reading of Penetration and subsequent resetting of a sample and accurate operation. The dial is graduated from 0-400 in on tenth millimeter Sub Division. The instrument is supplied with two samples containers made of aluminium. The penetration is the distance in millimeter that a standard needle penetrates vertically into a sample of the material under fixed conditions of loading time and temperature. This instrument measures the reading on round dial fitted on a Aluminium Painted stand having adjustable penetration needle, holder sample container and transfer dish.
Features
Range of Experiments
Description
The displacement of an edge cam as it rotates through 360 is measured using a dial gauge. The angular position of the cam is shown on a graduated scale. A tangent cam with a 25mm diameter follower are supplied as standard, and other cams and followers are available as optional ancilliaries, as shown in the specifications.
A variety of set ups is provided by a knife edge or roller follower in combination with a tangent cam, a contant acceleration cam or a simple harmonic motion cam.
A set of optional extras htm88j provides a flat follower, lever and offset fittings and two more cams (one eccentrically pivoted and one for uniform motion).
This equipment is part of a range designed to both demonstrate and experimentally confirm basic engineering principles. Great care has been given to each item so as to provide wide experimental scope without unduly complicating or compromising the design. Each piece of apparatus is self-contained and compact. Setting up time is minimal, and all measurements are made with the simplest possible instrumentation, so that the student involvement is purely with the engineering principles being taught. A complete instruction manual is provided describing the apparatus, its application, experimental procedure and typical test results.
Features
Range of Experiments
Description
A steel disc 250 mm diameter and 30 mm thick is mounted on a shaft running in ball bearings housed on a substantial wall bracket. A mark on the flywheel and a pointer on the bracket enable the revolutions to be counted and timed with the stop watch supplied. A cord, load hanger and set of weights are provided.
This equipment is part of a range designed to both demonstrate and experimentally confirm basic engineering principles. Great care has been given to each item so as to provide wide experimental scope without unduly complicating or compromising the design. Each piece of apparatus is self-contained and compact. Setting up time is minimal, and all measurements are made with the simplest possible instrumentation, so that the student involvement is purely with the engineering principles being taught. A complete instruction manual is provided describing the apparatus, its application, experimental procedure and typical test results.
Features
Range of Experiments
Description
A steel disc 250 mm diameter and 30 mm thick is mounted on a shaft running in needle roller bearings housed on a substantial wall bracket. A mark on the flywheel and a pointer on the bracket enable the revolutions to be counted and timed with the stop watch supplied. A cord, load hanger and set of weights are provided.
The moment of inertia can be altered by the addition of a disc and a ring of similar masses. A vibrating arm provides an accurate means of measuring acceleration, drawing a simple harmonic curve at a frequency of 5Hz onto a strip of paper attached to the flywheel periphery. This is actuated automatically as the flywheel starts to rotate.
This equipment is part of a range designed to both demonstrate and experimentally confirm basic engineering principles. Great care has been given to each item so as to provide wide experimental scope without unduly complicating or compromising the design. Each piece of apparatus is self-contained and compact. Setting up time is minimal, and all measurements are made with the simplest possible instrumentation, so that the student involvement is purely with the engineering principles being taught. A complete instruction manual is provided describing the apparatus, its application, experimental procedure and typical test results.
This is widely used for determination of closed cup Flash Point of Fuel Oil, cut back asphalts, other viscous material and suspension of solids having a flash point about 490C(1200F).The apparatus serve the purpose according method B. The apparatus consists of Brass Test cup with handle removable cup cover with spring operated rotating shutter having piolet jet, stirrer with flexible shaft. The assembly rests in Air Bath which is covered with Dome shape metal top. The cup is fitted with insulated handle and locking arrangement near cup plange. The assembly rests on a round shaped heater with different temperature regulation system suitable for operation on 220 Volts AC mains.
Used for determining of the closed cup Flash point of Petroleum Products, their mixtures, others liquids & Paints having Flash Point below 700C. The apparatus consists of one brass cup and cover fitted with shutter mechanism test flame arrangement(Oil test jet or Gas test jet) and stirrer, placed on a water bath made of copper sheet double walled. The outer jecket of the water bath is fitted with a stand. For electrically heated apparatus, heater is fitted to the stand the heat of which may be controlled different temperature regulation system of operated on 220 Volts AC mains. For Gas heated model the drum is heated by a burner. (without burner).
The appartus is used for determination of Flash Point & Fire Point of Petrolrum products except fuel oil with open flash 800C specification. The apparatus consists of a cup heating plate to specific dimensions thermometer clip and test flame attachment with swivel joint for passing over liquid s Fire Point Appurface in the prescribed manner, heater is controlled by means of different types of regulators fitted to the apparatus suitable for operation on 220 Volts AC mains.
