Elmes- India Impex LLP

Guindy, Chennai, Tamil Nadu

Elmes GSM alarm notification module is designed to operate with Elmes CB32 (firmware v.2.10 and up) wireless control panel., Can be used in any 90018001900 MHz cellular telephone network depending on applied SIM card. The module communicates, Sends SMS messages and CLIP calls to up to two predefined cell phones it notifies alarm system owner or monitoring station operator of occurred intruder alarms, system failures and system arming and disarming., The module uses embedded multi-band GSM network transceiver., Powered by 3, 7 volt lithium-ion or polymer type battery charged by Elmes CB32 control panel as backup power.

Umb100ht one channel keyfob transmitter

elmes key fob and hand held transmitters are compatible with wide range of elmes receivers.

• operating frequency band is 433, 92mhz.
• number of channels: 1
• 3-5mw transmits power.
• gp23a 12v battery.

technical specification

• dynamic code system keeloq of microchip corp. Usa
• average range: 100m in open field
• power supply: alkaline battery 12v, type gp23a
• operating temperature range from -20 to + 40c,
• external dimensions: (l/w/d) 46/34/14mm

UMB100H one channel with up to 100 meters operating range (433, 92 MHz)., It is widely used in alarm systems for remote starting of entry delay, system armingdisarming, access control and as personal panic button.Transmissions sent from the remotes are KEELOQ dynamic code encrypted allowing highest level of security., The receiver can operate with up to 12 remotes at a time (up to 112 on option) and provides one programmable and isolated from power supply NONC (NO-normally opened, NC-normally closed) relay output and one external beepersiren output S.

Wss outdoor siren and strobe

• elmes wss siren and strobe is alarm signaling device with loud siren and strobe light designed for outdoor installation in alarm and security systems.
• in addition to its alarming functions the siren features system arming and disarming confirmation sounds allowing home or property owner to external signaled arming and disarming of the system with the use of a key-fob remote control transmitter, just like remote setting on & off of a car alarm.
• microprocessors control of the wss siren along with two-way transceiver communication with elmes cb32 control panel enable remote selection of sirens functions using control panel keypad.
• though the siren is a fully supervised device dedicated to use with elmes cb32 panel, it may also be used in any alarm system, also hard-wired, when installed with optional "wired-to-wireless" interface module elmes wsm.
• commands and monitoring signals receipt are confirmed for security reasons. Other important features include anti-sabotage instant alarming and ac power supply failure notification.
• included with the siren 12v/1.2ah rechargeable battery is the master source of power supply to the siren and the strobe light both in normal operation and in case of ac power failure.
• the battery is charged by an external 230vac/12vdc-100ma power pack (included) plugged into 230vac mains outlet. The elmes wss siren & strobe may also be powered from wired alarm 13.8vdc power line or any external 13.8vdc battery backup power supply.

technical specification

• dynamic code system keeloq of microchip corp. Usa
• eu standards compliant 433, 92mhz transceiver
• 120db siren and strobe light with anti-sabotage protection
• microprocessor controlled ce433, 92mhz transceiver;
• average range: 200m in open field
• two way communication system
• mains power pack 16vdc/100ma and 12v/1.2ah battery included.
• compatible directly with cb32 v 2.10 or higher versions
• compatible with any wired alarm panel via wsm control module
• operating temperature range from -20 to + 40c,
• external dimensions: (l/w/d) 260/145/82mm.

ELMES key fob and Hand held transmitters are compatible with wide range of Elmes Receivers.Operating frequency band is 433, 92MHz, Number of channels: 1, 3-5mW transmits power., GP23A 12V battery.

Dynamic code system KEELOQ of Microchip Corp. USA, Operating frequency: 433, 92 MHz., Number of channels: 2., Approximate range in open field: 50m., Operating temperature range from 0 to + 40C.

UMB100H one channel with up to 100 meters operating range (433, 92 MHz), One relay output channel universal remote control, It is widely used in alarm systems for remote starting of entry delay, system armingdisarming, access control and as personal panic button, Transmissions sent from the remotes are KEELOQ dynamic code encrypted allowing highest level of security, The receiver can operate with up to 12 remotes at a time (up to 112 on option) and provides one programmable and isolated from power supply NONC (NO-normally opened, NC-normally closed) relay output and one external beepersiren output S.

GSM-1 Alarm Communicator

• Elmes GSM alarm notification module is designed to operate with Elmes CB32 (firmware v.2.10 and up) wireless control panel.
• Can be used in any 900/1800/1900 MHz cellular telephone network depending on applied SIM card. The module communicates
• Sends SMS messages and CLIP calls to up to two predefined cell phones it notifies alarm system owner or monitoring station operator of occurred intruder alarms, system failures and system arming and disarming.
• The module uses embedded multi-band GSM network transceiver.
• Powered by 3, 7 volt lithium-ion or polymer type battery charged by Elmes CB32 control panel as backup power.
• The battery secures module power supply backup in case of control panel mains supply failure.
• Simple installation procedures and practical notification features are advantages of the module for its application in alarm systems.

Technical Specification

• Full 900/1800/1900 Band Approved Embedded GSM Module SIM300C
• Communication with CB32 panel via AT commands (RS232 TTL 3, 3V) over cable interface,
• Internal cellular battery charged by CB32 panel (5VDC/300mA),
• Indoor operation with temperature range: 0 up to +40C,
• External dimensions: (L/W/D) 96/63/28mm, without antenna Mast.

UMB100HR Universal One Channel Receiver

• UMB100H one channel with up to 100 meters operating range (433, 92 MHz).
• One relay output channel universal remote control.
• It is widely used in alarm systems for remote starting of entry delay, system arming/disarming, access control and as personal panic button.
• Transmissions sent from the remotes are KEELOQ dynamic code encrypted allowing highest level of security.
• The receiver can operate with up to 12 remotes at a time (up to 112 on option) and provides one programmable and isolated from power supply NO/NC (NO-normally opened, NC-normally closed) relay output and one external beeper/siren output S.
• Receivers outputs are provided with terminals for easy wiring of external devices. The relay output action may be latched (on/off) or time-lapse mode operating depending on programming made by the user.
• The S output (open collector type) is for connecting external siren or beeper device and delivers two short pulses (two beeps) on relay set and one (one beep) on relay reset.
• The receiver features built in bi colour LED that is used for programming and signaling relay set (changes color). The set may be optionally ordered with super heterodyne receiver (UMB100Hhet) offering better operating range and greater rejection of interfering radio signals.

Technical Specification

• Receiver super regenerative (UMB100HR) or super heterodyne (UMB100HRhet)
• Power supply 12VDC 15%, current 20mA at standby or 20mA on relay set
• One relay output NO/NC handling 60VA (128VAC/1A)
• ON/OFF (bi stable output mode)
• Automatic OFF after programmed time (mono stable output mode timing: from 0, 25s up to 4 hrs)
• Anti-sabotage TAMPER switch with terminals
• Operating temperature range: 0 do +40C (-20 to +40C for AN200HRhet);
• External dimensions: (L/W/D) 96/63/28mm

• this remotely powered sounder features a piezo sounder and two bright leds for audible and visual indication. The sound output is selectable for either alternating or continuous tone. It is also protected against tampering by means of lid removal and removal from the mounting surface.

technical specification

• low profile design
• 115db sound output
• selectable alternating or continuous tone
• flashing alarm indication
• low current consumption
• tamper protected lid and mounting

Dynamic code system KEELOQ of Microchip Corp. USAOperating frequency: 433, 92 MHz, Periodic identification transmission, Average range: 100m in open field, Power supply: alkaline battery 9V, Operating temperature range 0 to + 40C, , External dimmensions: (LWD) 1043024mm

The device allows monitoring of events occurring in alarm and security systems as well as operation in remote control systems by means of SMS., Notifications and CLIP calls, in any mobile phone 90018001900 MHz GSM network. In remote control operation, devices can be directly connected to its relay outputs and controlled also by means of SMS & CLIP (Calling Line Identification Presentation - a supplementary GSM service used to show the number of a caller). Specified below are characteristic features of Elmes GSM2 module:

Dynamic code system KEELOQ of Microchip Corp. USA, Operating frequency: 433, 92 MHz, Average range: 100m in open field, Power supply: alkaline battery 12V, type GP23A, Average battery life time: 2 years, Operating temperature range 0 to + 40C, External dimensions: (LWD) 195832mm

The set is used in alarm systems for remote starting of entry delay, system armingdisarming and access control.Control signals from the remotes are KEELOQ dynamic code encrypted providing highest level of security.The receiver can operate with up to 12 remotes at a time (up to 112 on option) and provides two programmable and isolated NONC (NO-normally opened, NC-normally closed) relay outputs and external beeper control output S. Outputs are terminals equipped allowing easy connection of external devices.The output relay action may be latched (onoff) or time-lapse (pulse) mode depending on programming made by the user. The S output (open collector type) is for connecting external signaling device and delivers two short pulses (two beeps) on relay set and one (one beep) on relay reset.The receiver features bi colour LED used for programming indication and first channel relay set. Two other LED diodes indicate channel 1 & 2 outputs set on.

STM receiver is designed to control one roller 230VAC electric induction motor with limit switch., Very small size of the receiver enables its installation under a wall switch inside the junction box 60mm deep. , It may also be installed inside the housing of the roller., STM includes superheterodyne radio receiver, KEELOQ dynamic code encryption and is compatible with the following Elmes Electronic keyfobhand transmitters: DWB100T, DW200HT, CH4HT, CH4H200T, CH8HT, CH32HT.Note: It is not compatible with UMB100HT.

A full range of addressable heat & smoke detectors and manual pull stations for our fire alarm systems.