• Highly Efficient
• Corrosion resistant for high durability
• Provides uniform heat transfer over the entire surface
• Stainless steel top surface is good for specimen contrast
• Insulated top plate in order to avoid heat transfer to control panel
• Aesthetic outer appearance
• Compact and unique design
• Supplied with suitable cord wire and plug

• Body : Mild Steel material
• Paint : Powder coating
• Top Plate : S.S. 304/Aluminum Material
• Temp controller : Digital PID controller
• Temp range : Ambient + 5 C to 70 C
• Control Accuracy : 0.5 C
• Display : Digital LED display
• Heating elements : Sealed heating elements
• Heater capacity : 0.5 KW
• Insulation : Cera wool insulation
• Operates on : 230 Volts, 50 Hz, AC supply
• Working size : 30 x 20 x 15 cm (L x B x H)

The consistency and workability of concrete is a very important factor and is strictly connected to the water/cement ratio, to the effect of admixtures and finally to the strength and quality of concrete. Suitable for concrete mixes of high and very high workability. To perform this test, a sample is placed on a metal surface which is then raised and dropped through a known height.

General Description And Specification As per IS : 5512 for cement Mortar and Lime

The flow table consists of a brass table top 250 + 2.5mm dia mounted on a rigid stand. The table top is reinforced with equally disposed ribs and allowed to drop through 12mm by a ground and hardened cam, Complete with mould 100mm base dia, 70mm top dia and 50mm high. The cam shaft is rotated at the rate of 100 RPM by an electric motor. Suitable for operation on 230 Volts 50 cycles. Single Phase, A.C. Supply. Manually operated flow table also available.

As per Is : 199 for concrete

The Flow Table consists of a brass or Mild steel table top of 76.2 cms(30")dia, finely machine from a solid brass casting or Mild steel Plate. The stand is fabricated out of cast iron/mild steel and is of study construction. The ground and hardened steel cam is designed to drop the table by 12.5mm. Complete with flow mould with handles with one tamping rod 0-60 cms long X 16cm. electrically operated to raise and drop the table top. approx. 15 times in 15 seconds. Suitable for operation on 230 volts, 50 cycles, A.C. Supply. Manually operated flow table also available.

Optional Accessories

Concrete scoop

shaft is rotated at the rate of 100 RPM by an electric motor. Suitable for operation on 230 volts 50 cycles, single phase, AC Supply.

The flow table determining the flow of portland coment concrete. Consists of flow table a top 76.2 cms (30") dia, finely machined froma solid brass/gunmetal casting. The stand is fabricated out of cast iron/mild steel and is of study construction. The ground and hardened steel cam is designed to drop the table by 12.5 mm. complete with flow mould with handles with one tamping rod 0-60 cms long X 16 mm dia. Electrically operated to raise and drop the table top. Approx. 15 times in 15 seconds. Suitable for operation on 230 volts, 50 cycles, A.C. Supply.

• Highly Efficient
• Corrosion resistant for high durability
• Provides uniform heat transfer over the entire surface
• Stainless steel top surface is good for specimen contrast
• Insulated top plate in order to avoid heat transfer to control panel
• Aesthetic outer appearance
• Compact and unique design
• Supplied with suitable cord wire and plug

• Body : Mild Steel material
• Paint : Powder coating
• Top Plate : S.S. 304/Aluminum Material
• Temp controller : Digital PID controller
• Temp range : Ambient + 5 C to 70 C
• Control Accuracy : 0.5 C
• Display : Digital LED display
• Heating elements : Sealed heating elements
• Heater capacity : 0.5 KW
• Insulation : Cera wool insulation
• Operates on : 230 Volts, 50 Hz, AC supply
• Working size : 30 x 20 x 15 cm (L x B x H)

The consistency and workability of concrete is a very important factor and is strictly connected to the water/cement ratio, to the effect of admixtures and finally to the strength and quality of concrete. Suitable for concrete mixes of high and very high workability. To perform this test, a sample is placed on a metal surface which is then raised and dropped through a known height.

General Description And Specification As per IS : 5512 for cement Mortar and Lime

The flow table consists of a brass table top 250 + 2.5mm dia mounted on a rigid stand. The table top is reinforced with equally disposed ribs and allowed to drop through 12mm by a ground and hardened cam, Complete with mould 100mm base dia, 70mm top dia and 50mm high. The cam shaft is rotated at the rate of 100 RPM by an electric motor. Suitable for operation on 230 Volts 50 cycles. Single Phase, A.C. Supply. Manually operated flow table also available.

As per Is : 199 for concrete

The Flow Table consists of a brass or Mild steel table top of 76.2 cms(30")dia, finely machine from a solid brass casting or Mild steel Plate. The stand is fabricated out of cast iron/mild steel and is of study construction. The ground and hardened steel cam is designed to drop the table by 12.5mm. Complete with flow mould with handles with one tamping rod 0-60 cms long X 16cm. electrically operated to raise and drop the table top. approx. 15 times in 15 seconds. Suitable for operation on 230 volts, 50 cycles, A.C. Supply. Manually operated flow table also available.

Optional Accessories

Concrete scoop

shaft is rotated at the rate of 100 RPM by an electric motor. Suitable for operation on 230 volts 50 cycles, single phase, AC Supply.

The flow table determining the flow of portland coment concrete. Consists of flow table a top 76.2 cms (30") dia, finely machined froma solid brass/gunmetal casting. The stand is fabricated out of cast iron/mild steel and is of study construction. The ground and hardened steel cam is designed to drop the table by 12.5 mm. complete with flow mould with handles with one tamping rod 0-60 cms long X 16 mm dia. Electrically operated to raise and drop the table top. Approx. 15 times in 15 seconds. Suitable for operation on 230 volts, 50 cycles, A.C. Supply.