EIE Instruments Private Limited

Paldi, Ahmedabad, Gujarat

• To determine the resistance to abrasion on glazing tiles. The ability of glazed tiles to resist surface abrasion, encountered in everyday use, is determined by abrading the glazed surface either with a wet abrasive media or with a dry abrasive media.

• Steel balls of 1mm - 5mm diameter
• Aluminum oxide abrasive powder

• Porcelain cylinders
• Silicon carbide powder

• Distilled water

• Easy to use and with rugged construction
• Electronically controlled RPM Indications
• Mild steel structure body with powder coating paint
• Rotational speed defined and calibrated at 300 RPM
• Strictly abiding to listed international standards

• Used for determination of the modulus of rupture (MOR) of dried or fired refractory shapes of all types

3 KVR servo controlled stabilizer is recommended

• Standard PC Software to log and modify the series of results for future provisions
• Closed loop programmable servo mechanism with position feedback (encoder) system

• Electro-Mechanical Design
• Quite and vibration free operation
• Standard Digital Model with Load Cell and LCD Display
• Programmable rate of loading
• Auto stop and Auto reverse upon breaking of the sample
• Selectable test units KG / KN
• Special acrylic guard to protect the user against ceramic sprinkles
• Maximum load Capacity : 1000 kgf
• Least Count : 1.0 Kgf
• Fire brick size of : 230 mm length x 115 mm width x 76 mm thickness cane be tested
• Operation on : 230 Volts, 50 Hz, Single Phase, AC Supply

• Electro-Mechanical Design
• Quite and vibration free operation
• Standard Digital Model with Load Cell and LCD Display
• Programmable rate of loading
• Auto stop and Auto reverse upon breaking of the sample
• Selectable test units KG / KN
• Special acrylic guard to protect the user against ceramic sprinkles
• Maximum load Capacity : 1000 kgf
• Least Count : 1.0 Kgf
• Accuracy : 0.2% of Full Scale
• Can accommodate : Maximum upto 600 x 600 mm Tile size
• Operation on : 230 Volts, 50 Hz, Single Phase, AC Supply

EN 12390-4, ASTM C39, AASHTO T22, IS : 14858 (2000)

• Set test parameters - including load rate and Press the start button
• The machine automatically starts the rapid approach; switches to the test speed once the specimen comes into contact with the upper platen; automatically release the pressure upon specimen failure
• Save the test including data results and load-time graph (Optional)
• Dual stage pump assuring fast piston approach and precise test execution
• Test execution conforming to EN 12390-4, ASTM C39, AASHTO T22
• Controllable pace rate from 1 KN/Sec to 10 KN/Sec.
• Inbuilt graph in the touch screen display.
• Auto stop and auto release after completion of each test.
• Accuracy Class 1 (EN) and Class A (ASTM) starting from 10% of full scale.
• Soft platen-to-specimen contact and smooth load rate control from the very beginning of the ramp
• Allow remote verification of settings and performances.
• For easy debugging of unexpected malfunctions.
• Complete IP based controller.
• Working on 240V, 50-60Hz, single phase.

• Four column high stiffness welded frame tested for stability.
• Heavy duty spherical seat in lubricating oil bath, allowing initial free alignment at the initial contact with the specimen and automatic jamming up to the end of test.

• Series TM-042-AA fitted with 300 mm dia. platens which are suitable for testing cylinders up to dia. 150x300 mm and cubes up to 200 mm.
• Surface hardness of platen is 55 HRC, flatness tolerance 0.03 mm. Traceable certificate of surface hardness available on request.
• Attachment for Paver block testing is available at extra cost.

• Max. pressure valve to avoid machine overloading
• Piston travel limit switch (Extra cost)
• Emergency stop button

132, 000 points effective resolution, touch screen graphic display 240 x 128 pixel, sampling rate 50/sec, large storing capacity on USB pen drive test data downloadable to PC, Ethernet port, real time management software (optional).

• Dedicated Data manager PC software

• 1. Tensile Test
• 2. Peel, Adhesion & Bond Test
• 3. Compression Test
• 4. Stiffness Test
• 5. Flexural Bend Test

• 6. Shear Test
• 7. Torsion Test
• 8. Tear And Friction test
• 9. Fracture And Crack Growth test
• 10. Modulus of Elasticity test

• 1. Plastics (Pipes/Films/Laminations)
• 2. GEOSYNTHETIC / GEOTEXTILE Material
• 3. Textiles Material
• 4. Wood and Timber

• 5. Paper and Paper products
• 6. Elastomer and rubber
• 7. Metal

ASTM D638, ASTM D790, ASTM D3039, ASTM D882, ASTM D412, ASTM D429, ASTM D624, ASTM D76, ASTM E154, ASTM C836, ASTM D2240, ASTM D3039, ASTM D3786, ASTM D4533, ASTM D4595, ASTM D4632, ASTM D4833, ASTM D6241, EN 12311-1 /ISO R527, DIN 53504, EN 12310 Part 1:2000, EN ISO 12236, ISO 34, ISO 10319, ISO 527, ISO 178, ISO 2062, ISO 604, IS 13360, IS 3400, IS 15477

• High grade steel gives unmatched performance, accuracy and precision
• Rigid machine frame with high stiffness
• Equipped with multi-position limit detectors for best protection of operator, test sample and machine
• Column protection over total traverse stroke

Cross head driven by Backlash free ball screw assembly to provide high load capacity

Maximum travel from grip to grip is 800mm at extension least count of 0.01mm. Higher length is also available on demand (optional).

PLC (Programmable Logic Controller) and Smart Touch Screen HMI Display. Economy models comprises of Microprocessor based Digital controller in place of PLC & HMI.

RS-232/RS-485/Ethernet based PLC controller, Profile based software to start the test quicker, Menu driven software parameters, User-friendly and easy to understand, Can provide full control of all parameters, Full test analysis with statistical and graphical print-out, User can export the generated data in Excel, PDF, Word format.

Choose from a wide range of grips and fixtures for tension, compression, flexural, shear, peel, puncture and bond testing

Max Load, Max Elongation, Yield force, Yield Elongation, Break force, break elongation, GPD, etc test results and parameters can be observed on HMI Screen & In dedicated software.

Tensile as well as compression test facility available, mode selection via software. No need to change mode every times before starting the new test.

Over load protection, reverse direction load protection, Maximum elongation protection for load cell, Limit switches on either end etc.

For testing metals and other materials under tension, compression bending, transverse and shear loads. Hardness test on metals can also be conducted.

200 kn, 400 kn, 600 kn, 1000 kn

• Computerized Electronic Universal Testing Machine
• Microprocessor based control panel
• Auto ranging
• Digital display of Load and Elongation
• Dedicated PC Software
• Electronic Extensometer (At extra cost)
• Export worthy colour combinations,
• Special sheet jaws, Hard chrome plating, Hose pipes,
• Reputed make Induction/AC Servo motor

1) Tension test, 2) Compression test3) Transverse test

1) Shear test attachment for bolt2) Wire rope test attachment3) Rebend test attachment4) Rebend test mandrels

The aggregate impact value of coarse aggregate provides a relative measure of the resistance of an aggregate to sudden shock or impact. The oven dried and accurately weighed aggregates are subjected to a total of 15 blows of specified weight and fall and percentage of fines formed in terms of the total weight of the sample is expressed as the aggregate impact value.

Consists of base weighing between 20-30 kg with a lower surface of not less than 30cm and support columns to form a rigid frame work around the quick release trigger mechanism to ensure an effective free fall of the hammer during test. The free fall can be adjusted through 380 + 5.0mm. The hammer is provided with a locking arrangement. A metal tup (hammer) weighing 13.5 to 14.0 kg, the lower end of in cylinderical shape, 100mm in diameter and 5cm long with a 2mm chamfer at the lower edge and case hardened. Complete with a cylindrical cup, 102mm dia x 50mm depth, one measure 75mm dia x 50mm deep and a tamping rod of circular cross section 10mm in diameter and 230mm long, rounded at one end.

The following accessories are not part of the standard supply and are supplied at an extra cost.

• Test Sieve 10mm, 12.5mm and 2.36mm opening.
• Laboratory Oven.
• Automatic Blow Counter.
• Electronic Balance 500gm x 100 mg / Two Pan Balance.

For the determination of resistance of aggregate to wear by abrasion. Two hollow cylinders, closed at one end and provided with tightly fitting covers at the other end. The inside diameter of the cylinder 20 cms and 34 cms depth. The cylinders are mounted on a shaft at an angle of 30 with the axis of rotation. The shaft rotates at 30-33 rpm through a reduction gear, coupled to a motor. Suitable for operation on 440 volts, three phase, 50 cycles, AC supply. Supplied complete with a counter and push button starter. With 12 nos cast iron spheres or steel spheres (steel balls) hardened, approx. 48 mm in diameter, each weighing 380-445 gm.

The machine is used for testing crushed slag, crushed and uncrushed gravel for resistance to abrasion. The aim of the test is to find the percentage wear due to the relative rubbing action between the aggregates and steel balls as abrasive charge. The oven-dried arrangements are weighted and rotated along with abrasive charge in the machine for the 500 or 1000 revolutions and percentage of wear so found out its reported as Los angeles abrasion value.

Consists of a hollow steel cylinder, closed at both ends, having an inside diameter of 700mm and inside length of 500mm. The cylinder mounted on a sturdy frame on ball bearings. The opening is closed dust tight with a removable bolted cover in place. A detachable shelf which extends through the drum catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated at a speed of 30-33 RPM by an electric motor through a heavy duty reduction gear. Fitted with revolution counter and push button starter. Supplied complete with a tray for collection of the material. Abrasive charge consists of set of 12 Nos. cast iron spheres or steel spheres (hardened steel balls) approximately 48mm diameter each weigh between 390-445 gram. Complete as above.

The following accessories are not part of the standard supply and are supplied at an extra cost.

• Laboratory Oven.
• Test Sieve 1.7mm
• Electronic Balance of 15 kg x 1 gm
• Spare Abrasive charge

With refrigeration system and micro-processor based digital temperature controller

Ductility is defined as distance in cms to which a standard briquette of bitumen can be stretched before the thread breaks. The briquette is stretched at a rate of 50 mm/min. 2.5mm per minute at a temperature of 27C 0.5C

The Machine is having built in refrigeration system to work a below ambient temperature up to 10C in tropical conditions. The Machine will operate at 27C with control accuracy of 0.5C as per the requirement of IS.

The apparatus consists of water bath with a heater, and a circulating pump to maintain uiform water tempetature . one half of the briquette moulds is fixed in a fixed plate in the water bath, the other half of the briquette mould is fixed to a carrier which slides over a rotating threaded shaft with a clutch, The motor and gears to rotate the shaft are housed in a cabinet fixed above the other end of the bath. A pointer fixed to the carrier moves over. a scale graduated from 0-100 cm x 1mm fixed on the bath with "0" (Zero) of the scale towards the fixed plates side. The rotating shaft has 2 speeds of travel for the bracket, 5 cm/min.and 1cm/min. selected by a clutch. Water bath inside is of stainless steel with insulation and water drain cock . A heater with is fitted inside the water bath. The Temp. is controlled by dual display Microprocessor based Auto Tuning PID Digital Temp. indicator cum controller. Control switches for motor, stirrer, heater and indicator lamps are fixed at a convenient place on the water bath. Complete with three briqutte moulds and one base plate, All supply single phase. As per IS 1208.

The machine embodies an hydraulic system designed to meet the requirements of Indian standards Specification 516-1959 for compression tests on cement mortar cubes up to 7.06 cms.

The hydraulic jack of 500 KN capacity is fixed to the base. The upper platen has got a self aligning action and is attached to a screw which passes through the cross head plate, and can be raised or lowered for initial clearance adjustment. The lower platen rests on the jack ram and is positioned with the help of a centring pin. Loading is accomplished by upward movement of lower platen. A dust cover is provided on the jack to prevent any dust from going into the cylinder. A spacer with a centering locating pin is provided to test small specimens. The lower and upper platens of the machine are hardened ground and polished. Guidelines are marked on the lower platen to keep the specimen coaxial with the hydraulic jack.

The motorised pumping unit which is housed in an elegant console is of double plunger type and is driven by three phase 440 volts 50 cycles electric motor. The pumping unit is a seperate unit connected to the jack by means of a steel connecting tube. A junction box is suitably fixed to connect the motor to the mains through a push button starter. The pumping unit is fitted with a 20cm dia, dial hydraulic pressure gauge with 250 division i.e. 0-500 KN X 2 KN. A max red pointer is provided to facilitate taking readings after failure of the specimen. The pressure gauge is fixed at an Angle for easy readability. The machine is fitted with hand wheel control which enables the rate of application of load to varied.The machine is equipped with the facility of Hand Pumping in case of power failure.The electric pumping unit is fixed with a micro-switch to switch off the motor automatically as the load on the machine approaches the rated capacity. Relays are incorporated in the pumping unit so that in case of break down of power supply, the motor will stop and would not re start unless the starting switch is operated. Complete with our own calibration certificate for pressure gauge with National Traceability.

• The Machine can be supplied with NCCBM Calibration certificate at an extra cost.
• The Machine can also be supplied with 2 or 3 pressure Gauges of 100 KN, 250 KN and 500 KN for testing lower strength cubes or smaller size cubes.

Optionally, the machine can be supplied with digital load indicator and load cell in place of Pressure Gauge at an extra cost.
Price on request only.

• Manually Operated
• Motorized Unit

Manually operated :

0-500 Kg. Complete with one briquette mould and set of weights to weigh 50, 100, 150 and 200 kg. without lead shot.

Motorised Operated:

0-900 Kg. The instrument employs of friction free, accurate, double, lever system, the load being applied by means sliding weight on the top lever The capacity of the unit is 900 kgs. After fixing the briquette in the jaws, the machine is swithched on. The sliding weights slides over the calibrated lever thus applying tension to the specimen. A micron-Switch fitted instantly stops the machine on failure of the briquette and on failure the tensile load is accurately read to 0.5 Kg by means of a marker provided on the sliding weight. The machine can be made operationable for subsequent test only after bringing the sliding the weight to its zero position. Suitable for operation on 230 volts, 50 cycles, single phase, A.C. supply. Complete with one brass briquette mould and one base plate.

The digital compression testing machine has been designed to meet the need for a simple, economic and reliable means to test concrete for its compressive strength. The design expressive of simplicity, both of construction and operation, makes the machine easy to use and maintain. The unit is compact, making it useful for site and Laboratory applications. The digital machines are provided with a pace rate controller, to enable maintain a constant of loading.

• High stability four column load frame
• Each frame tested for stability and alignment to avoid tension failure during a test and to ensure centre loading
• Standard Platens for 3 X 6/ 4 X 8 and 6 X 12 cylinders included.
• A precise large diameter spherical upper platen for optimum results
• Variety of optional accessories for cubes, blocks, bricks and flexure test available
• Motorized hydraulic power pack or pumping unit with rapid approach and automatic overload protection
• Comes standard with safety Guards on all four sides.

The Complete unit comprises a Loading Unit which is of fully welded or two pillar model construction having a cross-head with a spherical seated platen. The lower platen is attached to the top of the piston. The Loading capacity is of 2000 KN, Cubes up to 200 mm & Cylinders up to 150 mm Dia X 300 mm Height can be tested using the appropriate spacers.

Pumping Unit with choice of compact power pack attached closely to the loading unit or separate hydraulic pumping unit, attached to the loading unit by high pressure hydraulic flexible hose pipe. The pump facilitates rapid approach of the platens for daylight closure and also provides comprehensive control over the application of load. A control valve provides fine control over the loading rate for accurate pacing.

Maximum load is held and retained for approx. 15 min, unless cancelled, using the panel mounted reset switch. Pace rate set for running the test can be maintained manually.

Model With digital Readout and pace rate Controller

• Digital Load indicator with RS 232 interface for connection to windows XP based computer system
• Digital Load indicator with printer interface
• Batteryback up for Digital Load indicator in case of power failure
• Additional Pressure Gauge as `stand by` load indicator for emergency use in case of power failure
• Spare Oil seal
• Flexural test attachment (to be ordered at the time of purchase of machine.) Can be accommodated later on, only if request received at the time of placement of order
• Brick test attachment
• Block testing attachment
• Spacers to accommodate small size cubes and cylinders
• Hydraulic Oil
• Ram extracting tool

This machine is quite useful on field Laboratories or mobile testing laboratories or Vans which frequently change site or location. It is particularly useful where constant and consistent Electric power is not available. The load is applied manually and observed on a Pressure gauge. The Pressure Gauge has maximum load indicator which stand still even after the specimen under test crushes and has to be set to zero manually.

• High Stability
• Self-aligning platen assembly.
• Gauges are calibrated in Kilo Newton against certified Proving Ring.
• Suitable for testing cubes of various sizes
• Using special platens, bricks also can be tested.
• Hard chrome plated piston with new type of long life oil seal.
• Four Pillar Model - superior in design, reliability and accuracy
• Practically no welded parts, all joints reinforced with heavy nut/bolt to withstand occasional over loading and to ensure center loading.
• Rounded Corners add to elegance and safeguard against injury
• Hardened and grinded platens with guide lines for placing sample for Testing

• Spare Oil Seal
• Brick Testing Attachment
• Hydraulic Oil (Tin of 5 Liters)

Although generally not such an important property of concrete than compressive strength, tensile strength values are often important to know when the concrete used free of reinforcement and may be subjected to some tensile force. The test method essentially involves applying a load at the centre of a beam of concrete supported at its ends. The load required to break the specimen is then recorded.

The machine consists of a motorized load frame. The lower platen has two rollers, the distance between which is adjustable. For 150 mm x 150 mm x 700 mm beam, the centre distance between the rollers is 600 mm, while it is 400 mm for beams of size 100 mm x 100 mm x 500 mm. The upper platen has also a pair of rollers whose distance adjustable. It is 200 mm centre to centre, for 150 mm x 150 mm x 700 mm size beam and 133 mm for 100 mm x 100 mm x 500 mm size beam. Total capacity of the machine is 100 KN. 150mm dia pressure gauge of 0-100 KN x 1 KN least count to indicate load is fixed on the load frame. A separate electrically cum hand operated pumping unit housed in a cabinet is supplied. On/Off switch and a slow/fast lever to control rate of loading are fitted on the front panel of the pumping unit. A facility for hand operation is provided. A micro switch and relay fitted inside the pressure gauge protect the unit from over loading.

Hand operated version consists of a load frame. A small hand pumping unit is attached to the load frame. Since this is a hand operated light weight machine. It is useful for field laboratory also.

• Spare Oil seal
• Hydraulic Oil ( tin of 5 ltrs)
• Beam Mould 10 X 10 X 50 cm
• Beam Mould 15 X 15 X 60 cm
• Beam Mould 15 X 15 X 70 cm
• Beam Mould 15 X 15 X 75 cm
• Trowel
• Concrete Scoop

Capacity 200 kg. for cement concrete flooring tiles. The specifications are similar to the above machine, but for the bearing rollers of 25 mm dia and spans of 150, 200 and 250 mm. The load is applied at the rate of 200 kg/min/meter. Without lead shots.

Pendulum impact tester serve for determining the impact strength of notched and unnotched metal bars of different sections and different lengths according to the charpy (Beam) method. The machine is meant for making charpy, Izod and tension impact tests. The Pendulum Impact Tester is designed conducting CHARPY IZOD and IMPACT TENSION Test. The test methods conform to IS : 1757-1973 and IS :1499-1077 and IS : 1598-1977. The impact energy absorbed by the specimen during rupture is measured as the difference between the height of drop before rupture and the height of rise after rupture of the test specimen and is read on the dial scale.

• 1. Tensile Test
• 2. Peel, Adhesion & Bond Test
• 3. Compression Test
• 4. Stiffness Test
• 5. Flexural Bend Test

• 6. Shear Test
• 7. Torsion Test
• 8. Tear And Friction test
• 9. Fracture And Crack Growth test
• 10. Modulus of Elasticity test

• 1. Plastics (Pipes/Films/Laminations)
• 2. Geo synthetics/Geo Textiles material
• 3. Textiles Material
• 4. Wood and Timber

• 5. Paper and Paper products
• 6. Elastomer and rubber
• 7. Metal

ASTM D638, ASTM D790, ASTM D3039, ASTM D882, ASTM D412, ASTM D429, ASTM D624, ASTM D76, ASTM E154, ASTM C836, ASTM D2240, ASTM D3039, ASTM D3786, ASTM D4533, ASTM D4595, ASTM D4632, ASTM D4833, ASTM D6241, EN 12311-1 /ISO R527, DIN 53504, EN 12310 Part 1:2000, EN ISO 12236, ISO 34, ISO 10319, ISO 527, ISO 178, ISO 2062, ISO 604, IS 13360, IS 3400, IS 15477

• High grade steel gives unmatched performance, accuracy and precision
• Rigid machine frame with high stiffness
• Equipped with multi-position limit detectors for best protection of operator, test sample and machine
• Column protection over total traverse stroke

Cross head driven by Backlash free ball screw assembly to provide high load capacity

Maximum travel from grip to grip is 800mm at extension least count of 0.01mm. Higher length is also available on demand (optional).

PLC (Programmable Logic Controller) and Smart Touch Screen HMI Display. Economy models comprises of Microprocessor based Digital controller in place of PLC & HMI.

RS-232/RS-485/Ethernet based PLC controller, Profile based software to start the test quicker, Menu driven software parameters, User-friendly and easy to understand, Can provide full control of all parameters, Full test analysis with statistical and graphical print-out, User can export the generated data in Excel, PDF, Word format.

Choose from a wide range of grips and fixtures for tension, compression, flexural, shear, peel, puncture and bond testing

Max Load, Max Elongation, Yield force, Yield Elongation, Break force, break elongation, GPD, etc test results and parameters can be observed on HMI Screen & In dedicated software.

Tensile as well as compression test facility available, mode selection via software. No need to change mode every times before starting the new test.

Over load protection, reverse direction load protection, Maximum elongation protection for load cell, Limit switches on either end etc.

A system of loading which causes section of a bar or shaft to rotate about its central longitudinal axis relatively to another such section and which thus produces twist or torsion in the bar, constitutes a torsional load. The load may be composed of forces acting in any direction but the twisting or torsional affect is provided by the couples formed by these forces in planes normal to the central axis. The torsional shearing stresses in circular cross section vary from zero at the axis of the section to a maximum value at the extreme fibres. If no bending is present pure shear exists. Torsion Testing machine Consists of two independent chucks. The twist is communicated through the test piece to the other jaw on which a weighted pendulum is attached. The resistance to deflection of pendulum causes a torque to be applied to the test piece and the angles of deflection of pendulum is the measure of torque. The machine is built for maximum twisting moment at about 50 kgm. It is equipped with jaws for accomo- dating test pieces of 10 mm, 15 mm and 20 mm size either square or circular with square shoulder.