Ecosens Lighting Pvt. Ltd.

Rohini, Delhi

The LED lamp connected to the output of the IR Sensonr switch will trun ON when the hand pass over the IR switch within 10cm in distance, and will turn OFF when the hand pass over again. The sensor switch will turn ON or OFF with above repeatable steps Function: The LED lamp connected to the output of the IR Sensonr switch will trun ON when the hand pass over the IR switch within 10cm in distance, and will turn OFF when the hand pass over again. The sensor switch will turn ON or OFF with above repeatable steps.

New version 20LED smd outdoor motion sensor solar led outdoor wall light

Measured or otherwise detected, and the passage of heat energy into or out of the space is adjusted to achieve a desired average Temperature.

The product is a new saving-energy switch; it adopts good sensitivity detector, integrated circuit. It gathers automatism, convenience, safety, saving-energy and practicality functions. The wide detection field is consisting of detectors. It works by receiving human motion infrared rays. When one enters the detection field, it can start the load at once and identify automatically day and night; its installation is very convenient and its using is very wide. It has functions of power indication and the detection indication.

DayNight Sensor can automatically turn on or off lights at dusk and dawn. It is not only convenient but also practical; it can control the lighting loads by working only at night. Examples of use are street lights, office lights, warehouse and factory lights, garden lights, etc. Its also known as Photocell Sensor, Light Sensor, Dusk to dawn sensor, Street light sensor, Day night Sensor, LDR Sensor.

This product is a new type of energy-saving lighting switch, it adopts high sensitivity detector, integrate circuit and SMT; It gathers automatic, convenient, safe, energy-saving, practical functions; It has wide detection range made up of up and down, left and right service field; It utilizes human motion infrared rays as control signal sources, when one enters the detection field, it will start the controlled load at once; It can identify day and night automatically; It is easy to install and its usage is wide; It has the function of power indication and detection indication.

A float switch is a device used to detect the level of liquid within a tank. The switch may be used in a pump, an indicator, an alarm, or other devices.

A very common application is in sump pumps and condensate pumps where the switch detects the rising level of liquid in the sump or tank and energizes an electrical pump which then pumps liquid out until the level of the liquid has been substantially reduced, at which point the pump is switched off again. Float switches are often adjustable and can include substantial hysteresis. That is, the switch's "turn on" point may be much higher than the "shut off" point. This minimizes the on-off cycling of the associated pump.

float switches contain a two-stage switch. As liquid rises to the trigger point of the first stage, the associated pump is activated. If the liquid continues to rise (perhaps because the pump has failed or its discharge is blocked), the second stage will be triggered. This stage may switch off the source of the liquid being pumped, trigger an alarm, or both.

detects natural gas, lpg, and coal gas etc. Combustible gases.

specification

gas leak detector alarm

220v, 12v, 9v battery back up

low battery and fault warning

connect with solenoid valve

ce, en50194

features

1. ce, en50194 approved gas leak detector/alarm;
2. 5 years lifetime, high accurate hot wire type sensor.
3. detects natural gas, lpg, and coal gas etc. Combustible gases.
4. power supply : 90-240v ac+ 9v battery back up, automatic switch between ac & dc power.
5. three indicators (3 different led lights display): power (green), alarm( red) , fault (yellow).
6. 10% lel sensitivity.
7. simple installation, ceiling or wall mounted.
8. sound(85 decibel) and flash alarm.
9. test/reset button;
10. can be connected with auto shut off solenoid valve.

Photoelectric Smoke Detector EL-S01, Properly installed and maintained. Residential smoke alarms, are one of the best and least expensive ways to provide an early warning when a fire begins. Smoke alarms save lives, prevent injuries and minimize property damage by alerting resident early to a fire hazard.

Specification:

• 9V Battery Operated
• Photoelectric Sensor
• Display:Two-Tone LED light indicator
• Mini size
• Low battery warning

FeaturesCE, EN14604 certificate

Mini size smoke detector

Photoelectric Sensor

9V battery operated

Low battery warnning indicator

Two tone LED light display, Flash alarm indicator (red LED) , Power indicator (blue LED)

Auto Test button for easy recommended monthly testing

Ceiling or wall mounted

Suitable for any rooms

Loud 85dB alarm signal