Our Products
Screws
2 Products availablePiston And Crankshaft Assemblies
1 Products availableBearings And Bearing Components
1 Products availableClamps And Clamping Equipment
1 Products availableHydraulic Machines
1 Products availableHardware Fittings And Accessories
1 Products availableGearboxes
1 Products availableGearbox & Gear Parts
1 Products availableOur product range contains a wide range of NC Rotary Table, NC Tilting Rotary Table and Hydraulic Indexing Table
Pneumatic Clamping System | ||||||||||
|
Model (Unit:mm) |
TD-125(V) |
TD-170(V) |
TD-200(V) |
TD-255P(V) |
|
Use Method |
Horizontal & Vertical (V-Vertical) |
||||
Clamp Method |
Pneumatic 5kg/cm2 |
||||
Faceplate Dimension |
Ø125 |
Ø170 |
Ø200 |
Ø255 |
|
Spindle Through Hole Diameter |
Ø22 |
Ø45 |
Ø45 |
Ø80 |
|
Faceplate Center Hole Diameter |
Ø40H7 |
Ø50H7 |
Ø50H7 |
Ø80H7 |
|
Center High |
110 |
135 |
160 |
160 |
|
Faceplate T Solt Width |
12H7 |
||||
Position Key |
14h7 |
18h7 |
|||
Servo Motor |
FANUC |
a2i |
a4i |
a4i |
a8i |
MELDAS |
HA23/33 |
HA40/HC52 |
HA40/HC102 |
HA80/HC152(102) |
|
Total Speed Reduction Ratio |
1/90 |
1/180 |
|||
Min. Speed Reduction Ratio |
0.001° |
||||
Indexing Accuracy (Cumulative)(Arc. Sec.) |
45 |
30 |
30 |
15 |
|
Repeatability (Arc.Sec.) |
4 |
||||
Clamp Force (kgf/m) |
8 |
16 |
16 |
45 |
|
Max. Torque Capacity of Worm Gear (kfg/m) |
15 |
27 |
27 |
48 |
|
Max. Workpiece of |
Vertical |
50 |
75 |
75 |
100 |
Horizontal |
100 |
150 |
150 |
250 |
|
Net weight (without motor) (kg) |
31 |
40 |
60 |
120 |
Pneumatic Clamping system, with built-in patented disk-clamping design (Taiwan PAT.: 217736) to ensure cutting endurance. | |
The feature of wear resistant alloy Dual-Lead Worm Gear is high mechanical efficiency of power transmission, high indexing accuracy and easy adjusted on the backlash. | |
Able to be connected with CNC machine to perform synchronous 5th axis multi-angle machining. | |
Able to be connected with CNC machine to perform tilting angle machine (4+1 axis) through Single Axis Controller. | |
Minimum Indexing Degree: 0.001 | |
Tilting range: +/- 110 |
Model | TTD-125 | TTD-255H | |||||
Tilt range | +110°~ -110° | +110°~ -110° | |||||
Spindle outer dia. | Ø60 | - | |||||
Table dia. | - | Ø255 | |||||
Table height at 0X position | 233 | 334.5 | |||||
Center height at 90X position | 160 | 220 | |||||
Center bore | Nose dia. | Ø25 | Ø30 | ||||
Thru dia. | Ø22 | Ø30 | |||||
Table T-solt width* | - | 12H7 | |||||
Guide block width | 14H7 | 18H7 | |||||
Servo motor | Rotary | Tilting | Rotary | Tilting | |||
FANUC | a2i | a4i | a8i | a8i | |||
MELDAS | HA33 | HA40 | HA80 | HA80 | |||
Inertia converted into motor shaft |
X10-3kg.m2 [X10-3kgf.cm.sec2] |
0.31 (3.1) |
0.52 (5.3) |
||||
Speed reduction ratio | 1:90 | 1:90 | 1:120 | 1:180 | |||
Max. table rotation speed (3000 r.p.m.) |
33.3 | 33.3 | 25 | 16.7 | |||
Clamp system supplied pressure |
Pneumatic 0.6MPa 5kgf/cm2 |
Hydraulic3.5MPa 35kgf/cm2 |
|||||
Clamp torque |
N-m [kgf-m] |
78 ( 8) |
157 ( 16) |
588 ( 60) |
686 ( 70) |
||
Indexing accuracy (cumulative) | arc sec. | 45 | 60 | 15 | 45 | ||
Repeatability | arc sec. | 4 | 4 | 4 | 4 | ||
Net weight | kg | 95 | 330 | ||||
Allowable wheel torque (Rotary axis) |
N-m [kgf-m] | 120(12) | 490(50) | ||||
Allowable work weight | 0° tilt angle | kg | 35 | 120 | |||
0°~90° tilt angle | kg | 20 | 70 | ||||
Allowable work moment | WxL |
N-m [kgf-m] |
156(16) | 470(48) | |||
Allowable load when table clamped |
F |
N [kgf] |
343(35) | 1170(120) | |||
FxL |
N-m [kgf-m] |
78.4(8) | 470(48) | ||||
FxL |
N-m [kgf-m] |
156(16) | 470(48) | ||||
Allowable work inertia | J=WD2/8 |
kg-m2 [kg.cm.sec2] |
0.18(1.7) | 0.7(6.9) | |||
Dimension(download)- JIF File | TTD 125 | TTD 255H | |||||
Dimension(download)- PDF File | TTD 125 | TTD 255H |
Model (Unit:mm) | TDM-170 | ||
Clamp Method | Pneumatic 5kg/cm2 | ||
Faceplate Dimension | p170 | ||
Spindle Through Hole Diameter | p45 | ||
Faceplate Center Hole Diameter | p50H7 | ||
Center High | 170 | ||
Faceplate T Solt Width | 12H7 | ||
Position Key | 18h7 | ||
Servo Motor | Rotate Axis | Tilting Axis | |
FANUC | \3/\4i/\8i | Manual | |
MELDAS | HA40/HF053T | ||
Min. Speed Reduction Ratio | 0.001° | 5' | |
Total Speed Reduction Ratio | 1/90 | ||
Indexing Accuracy (Cumulative)(Arc. Sec.) | 30" | ||
Repeatability (Arc.Sec.) | 4" | ||
Clamp Force (kgf/m) | 16 | ||
Max. Torque Capacity of Worm Gear (kfg/m) | 27 | ||
Tilting Angle | 0°~90° | ||
Max. Workpiece of Capacity (kg) |
Vertical (with tailstock) |
75 (150) |
|
Horizontal | 150 | ||
Net Weight (without motor) (Kg) | 90 | ||
Dimension(download)- JIF File | TDM-170 | ||
Dimension(download)- PDF File | TDM-170 |
Horizontal | ||||||||||||||||
|
Model (Unit:mm) |
CH3-340 |
CH3-470 |
CH3-470S |
CH3-600 |
CH3-600S |
CH3-800 |
Clamp Method |
Hydraulic 35kg/cm2 |
|||||
Faceplate Diameter |
Ø340 |
Ø470 |
470 |
Ø600 |
600 |
800 |
Spindle Through Hole Diameter |
Ø30 |
Ø40 |
Ø50 |
Ø45 | ||
Faceplate Center Hole Diameter |
Ø65 |
Ø90 |
Ø110 |
Ø100 | ||
Faceplate T Solt Width |
None |
None |
18H7 |
None |
20H7 |
|
Division |
Standard division: Every model have 4,6,8,12,24 standard, you can option any one of it. |
|||||
Indexing Accuracy(Arc. Sec.) |
±5 |
|||||
Repeatability (Arc. Sec.) |
±1 |
|||||
Max. Workpiece of |
500 |
700 |
1250 |
|||
Net weight (kg) |
130 |
275 |
330 |
450 |
560 |
1000KGS |
Dimension(download)-JIF File |
CH3-340 |
CH3-470 |
CH3-470S |
CH3-600 |
CH3-600S |
CH3-800 |
Dimension(download)-PDF File | CH3-340 | CH3-470 | CH3-470S | CH3-600 | CH3-600S | CH3-800 |