Drill Bitz India Pvt Ltd

Cv Raman Nagar, Bangalore, KA

R35 38 mm Radial Drill Machine with Fine Feed Specifications of Machine: Description R35Capacity Drilling In M.S. 38Drilling in C.I. 40Tapping in M.S. 20Drilling Head Spindle Hole Taper MT-4Spindle Travel 160Spindle Speed (RPM x Steps) 88-2600 x 8Diameter of RAM 78Auto feed Range ( mm/ rev) FINE FEEDWorking Range Max/Min Distance Spindle Nose to Base 914/200Max/Min Distance Spindle Center toColumn812/325Max. Drilling Radius 890Machine Measurement (L x B x H) 1300 x 762 x 1755Diameter Of Column 160Work Table 300 x 300 x 385Power Drill Head Motor 1.5 HP/1440 RPMElevating Motor 0.5 HP/1440 RPMHead Motor V-Belt B-46/B-47Lifting Motor V-Belt B-23/B-24

Specification of - P40AA and P40BA - Column Drill Machines:Description P40AA P40BACapacity Drilling In M.S. 40 40Drilling in C.I. 45 45Tapping in M.S. 25 25Rough Boring M.S. 75 65DrillingHeadDrive of the Spindle 9 Speed Oil BathGear Box4 Step Cone Pulleyand Back gear TypeSpindle Hole Taper MT-4 MT-4Spindle Travel 250 250Spindle Speed (RPM x Steps) 88-1404 x 9 80-2600 x 8Diameter of RAM 78 78Auto feed Range ( mm / rev) 2 / 0.05 & 0.09 2 / 0.05 & 0.09WorkingRangeMax. Distance Spindle Nose to Base 920 920Distance Spindle Nose to Table 530 530Distance Spindle Center to Column 345 345Table Size 450 x 455 450 x 455Machine Measurement (L x B x H) 880 x 675 x 1850 880 x 675 x 1850Diameter Of Column 130 130Power Motor 2 HP/ 3 HP 2 HPV-Belt B-33 x 2 B-79

Specification of Pillar Drill Machines:Description P38 P35 P25 P20Capacity Drilling In M.S. 38 35 25 20Drilling in C.I. 42 38 32 22Tapping in M.S. 20 20 15 20DrillingHeadSpindle Hole Taper MT-4 MT-3 MT-3 MT-2Spindle Travel 250 160 160 125Spindle Speed (RPM x Steps) 80-2600 x 8 80-2600 x 8 100-2650 x 8 50-3000 x 8Diameter of RAM 78 72 72 55Auto feed Range ( mm x rev) FINE FEED FINE FEED FINE FEED ----WorkingRangeMax. Distance Spindle Nose toBase920 1120 950 905Distance Spindle Nose to Table 610 670 560 605Distance Spindle Center toColumn321 260 206 206Table Size 425 X 425 355 x 355 330 X 330 260 x 260Machine Measurement (L x B xH)700 X 450 X1830690 x 470 x1778500 x 304 x1600480 x 330 x1300Diameter Of Column 110 180 90 75Power Motor 1.5 HP 1.5 HP 1 HP 0.5 HPV-Belt B-79 B-60 B-46 A-42

Specification of Pillar Drill Machines:Description P38 P35 P25 P20Capacity Drilling In M.S. 38 35 25 20Drilling in C.I. 42 38 32 22Tapping in M.S. 20 20 15 20DrillingHeadSpindle Hole Taper MT-4 MT-3 MT-3 MT-2Spindle Travel 250 160 160 125Spindle Speed (RPM x Steps) 80-2600 x 8 80-2600 x 8 100-2650 x 8 50-3000 x 8Diameter of RAM 78 72 72 55Auto feed Range ( mm x rev) FINE FEED FINE FEED FINE FEED ----WorkingRangeMax. Distance Spindle Nose toBase920 1120 950 905Distance Spindle Nose to Table 610 670 560 605Distance Spindle Center toColumn321 260 206 206Table Size 425 X 425 355 x 355 330 X 330 260 x 260Machine Measurement (L x B xH)700 X 450 X1830690 x 470 x1778500 x 304 x1600480 x 330 x1300Diameter Of Column 110 180 90 75Power Motor 1.5 HP 1.5 HP 1 HP 0.5 HPV-Belt B-79 B-60 B-46 A-42

Specification of Pillar Drill Machines:Description P38 P35 P25 P20Capacity Drilling In M.S. 38 35 25 20Drilling in C.I. 42 38 32 22Tapping in M.S. 20 20 15 20DrillingHeadSpindle Hole Taper MT-4 MT-3 MT-3 MT-2Spindle Travel 250 160 160 125Spindle Speed (RPM x Steps) 80-2600 x 8 80-2600 x 8 100-2650 x 8 50-3000 x 8Diameter of RAM 78 72 72 55Auto feed Range ( mm x rev) FINE FEED FINE FEED FINE FEED ----WorkingRangeMax. Distance Spindle Nose toBase920 1120 950 905Distance Spindle Nose to Table 610 670 560 605Distance Spindle Center toColumn321 260 206 206Table Size 425 X 425 355 x 355 330 X 330 260 x 260Machine Measurement (L x B xH)700 X 450 X1830690 x 470 x1778500 x 304 x1600480 x 330 x1300Diameter Of Column 110 180 90 75Power Motor 1.5 HP 1.5 HP 1 HP 0.5 HPV-Belt B-79 B-60 B-46 A-42

Dc-410 42 mm cap. Double column allgeared autofeed radial drill machine specification of machine:capacity drilling in mild steel 42 ( 1 5/8)drilling in cast iron 50rough boring in mild steel 60tapping in mild steel 25drilling head spindle taper mt-4 / mt-5spindle travel 225spindle speed (rpm x steps) 12 steps60, 90, 115, 165, 200, 290, 340, 480, 575, 825, 1005, 1510diameter of ram (quill) 78no. Of spindle auto feed ranges (mm/rev) 6 steps0.1, 0.15, 0.20, 0.27, 0.33, 0.52working range max / min distance spindle nose to base 1225 /450vertical travel of arm 775max / min distance spindle center tocolumn1025 / 275horizontal travel of arm 750max drilling radius 1137machine measurement (l x b x h ) 1600 x 850 x 2270diameter of column 225work table 500 x 450 x 400coolant tank 770 x 430 x 14550 literspower drill head motor 2 hp(1.5 kw) 960/1440 rpmelevating motor 0.75 hp(0.56 kw) 960 rpm left hand operation with ergonomic world class design. independent locking of drill head with arm, arm with sleeve and sleeve with column for easy setting. use of high grade - fine grain materials and precision manufacturing guarantee long life of machine. easily accessible front panel arrangement of electrical and mechanical controls. Base:more wider base for working area. coolant tank of 50 liters. rigid box type construction. more wider base for better work piece grip. Lifting nut:4 " long lifting screw nut made up of brass. Column assembly:double column type structure with dia 225 mm and inside ribs for more rigidity and smooth movement. Arm:no. Description dc 410capacity drilling in mild steel 42 ( 1 5/8)drilling in cast iron 50rough boring in mild steel 60tapping in mild steel 25drilling head spindle taper mt-4 / mt-5spindle travel 225spindle speed (rpm x steps) 12 steps60, 90, 115, 165, 200, 290, 340, 480, 575, 825, 1005, 1510diameter of ram (quill) 78no. Of spindle auto feed ranges (mm/rev) 6 steps0.1, 0.15, 0.20, 0.27, 0.33, 0.52working range max / min distance spindle nose to base 1225 /450vertical travel of arm 775max / min distance spindle center tocolumn1025 / 275horizontal travel of arm 750max drilling radius 1137machine measurement (l x b x h ) 1600 x 850 x 2270diameter of column 225work table 500 x 450 x 400coolant tank 770 x 430 x 14550 literspower drill head motor 2 hp(1.5 kw) 960/1440 rpmelevating motor 0.75 hp(0.56 kw) 960 rpmarm and column rigidly built with reinforcement ribs to reduce distortion, to give high capacity and lastingaccuracy. Gearbox:completely oil bath gear box with 12 spindle speed steps with near geometric progression for the optimumuse of machine. Gears:all gears gearbox are made up of nicr steel with hardness of50-55 hrc with thickness of 15 mm. Shafts of gears:all shafts made of nicr alloy steel with hardness 55 hrc. all four splines and six splines of shafts are ground onspilne grinding machine. Spindle:spildle & spindle ram(quill) are made up of nicr steelwith final hardness of 55 hrcspindle is fitted with precision angular contact bearings not the taper roller bearings. bearing sizes are internal ground. pinion supported through bearings. Ram liner bush:head stock is provided with high grade cast iron liner bush like in automobile engines for easysliding movement of ram and very long life. Also it ensures interchangeability when replacing after wearout. Auto feed system:6 auto feed near geometric progression for all processes to be done like drilling, reaming, boring, etc. overload safety clutch system for tool protection and machine protection. spindle auto-stop with travel adjustment. Spring:heavy duty helical spring has replaced old conventional type coil spring. This ensures far more life thanconventional springs. limit safety devices are used to assure security while arm up-down, arm lock, spindle depth adjustment

R40aa - 40 mm cap. All geared auto feed radial drill machine specification of machine: capacity drilling in m.s. 40drilling in c.i. 45tapping in m.s. 25rough boring m.s. 60drilling head spindle hole taper mt-4spindle travel 250spindle speed (rpm x steps) 58-936 x 9diameter of ram 78spindle auto feed range 0.05 & 0.09 mm/revworking range max / min distance spindle nose to base 950/250max / min distance spindle center tocolumn900/400max. Drilling radius 990machine measurement (l x b x h) 1200 x 780 x 2100diameter of column 180work table 300 x 300 x 385coolant tank 640 x 290 x 130power dill-head motor 1.5 hp/960 rpmelevating motor 1hp/1440 rpmlifting motor v-belt b-25/b-26 it is having gear box of 9 speeds with all 9 gears of nicr steel and hardened up to 55-60 hrcand tampered. oil bath gear box and hardened gears give very long life to the machine. auto feed gears are also hardened and tampered. all the gears in the machine are supported through good quality bearings and not thebushes. machine is supplied with complete electrical panel board and limit switch and 2. Nos. Isielectrical motors. rotation and easy sliding of gears in bearings give very high reliability. base plate is provided with in-built coolant tank. steel ram and pinion with 9 dp heavy duty teeth with 250 mm spindle travel enablesgreater loading capacity.

R40 - 40mm Cap Radial Drill Machine with Fine Feed Specifications of Machine Description R40Capacity Drilling In M.S. 40Drilling in C.I. 45Tapping in M.S. 25Drilling Head Spindle Hole Taper MT-4Spindle Travel 250Spindle Speed (RPM x Steps) 88-2600 x 8Diameter of RAM 78Spindle Auto feed Range Fine FeedWorking Range Max / Min Distance Spindle Nose to Base 850/250Max / Min Distance Spindle Center toColumn920/385Max. Drilling Radius 1005Machine Measurement (L x B x H) 1300 x 850 x 1825Diameter Of Column 170Work Table 300 x 300 x 385Power Dill-Head Motor 1.5 HP/1440 RPMElevating Motor 0.5HP/1440 RPMHead Motor V-Belt B-46/B-47Lifting Motor V-Belt B-23/B-24 Features :The all new 40 mm cap. Radial drill machine is having complete oil bath liftingassembly with the shaft supported at both ends by bearings and not the bushes.Also the heavy duty lifting screw (35mm) is supported through taper roller bearing.It is having wide support of column (170mm with extra rib), column bracket(440mm) and arm (305mm).Column is made of casting having long bottom for greater rigidity to reduce vibration.The base plate is heavily ribbed below for extra rigidity.Most important part spindle is internally and externally ground made of EN8 steel.Spindle quill is of 78 mm dia made of steel only not the casting.Pinion of EN8 steel and quill both are having 10 DP heavy teeth.Greater support through wider drilling head(250mm) and closed V-Guide ways onnewly designed channel type arm.

R40BA - 40 mm cap.Backgeared Auto feed Radial Drill MachineSpecifications of machine: Description R40BACapacity Drilling In M.S. 40Drilling in C.I. 45Tapping in M.S. 20Rough Boring M.S. 60Drilling Head Spindle Hole Taper MT-4Spindle Travel 250Spindle Speed (RPM x Steps) 88-2600 x 8Diameter of RAM 78Spindle Auto feed Range 0.05 & 0.09 MM/REVWorking Range Max / Min Distance Spindle Nose to Base 850/250Max / Min Distance Spindle Center toColumn920/385Max. Drilling Radius 1005Machine Measurement (L x B x H) 1350 x 850 x 1825Diameter Of Column 170Work Table 300 x 300 x 385Power Drill-Head Motor 1.5 HP/1440 RPMElevating Motor 1HP/1440 RPMHead Motor V-Belt B-47Lifting Motor V-Belt B-25/B-26 The All new model 40 mm Back geared Auto feed Radial Drill Machine is meant for heavygeneral purpose work.It is having heavy duty machine structure having 40 mm capacity in steel & 250 mm spindletravel.Dist. From spindle center to column is 900 mm.Column of 170mm dia is made of casting having long bottom for greater rigidity to reducevibration.The base plate is heavily ribbed below for extra rigidity.Most important part spindle is internally and externally ground made of EN8 steel.Spindle RAM is of 78 mm dia made of steel only not the casting with 250 mm spindle travel.Pinion of EN8 steel and quill both are having 9 DP heavy teeth.Auto feed gears are also hardened.All the gears in the machine are supported through good quality bearings and not thebushes.

R40g 40mm cap. Allgeared finefeed radial drill machine specification of machinedescription r40gcapacity drilling in m.s. 40drilling in c.i. 45tapping in m.s. 25drilling head spindle hole taper mt-4spindle travel 250spindle speed (rpm x steps) 58-936 x 9diameter of ram 78spindle auto feed range fine feedworking range max / min distance spindle nose to base 850/250max / min distance spindle center tocolumn920/385max. Drilling radius 1005machine measurement (l x b x h) 1350 x 850 x 1825diameter of column 170work table 300 x 300 x 385power drill-head motor 1.5 hp/960rpmelevating motor 0.5 hp/1440 rpmlifting motor v-belt b-25/b-26 gear box:gear box is having flange mounted motor to give the drive to the gearbox. Speeds are changedthrough gears only. gear box with 9 speed and all 9 gears of hardened nicr steel up to rc-50 to 60 is completely oilbath drive. Thus oil bath drive and hardened gears give very long life to the machine with no needfor lubrication. sliding of gears through bearings makes easy sliding. Also it has long life due to bearings. gears are internally splined and shafts are externally splined. This system totally eliminatesproblem of key wearage. two pairs of three gears each are made from one-piece as a cluster gear eliminating slippingproblem of press fitted gears. Spindle assembly:78 mm dia steel ram with 9 dp heavy teeth. pinion with 9 dp heavy teeth is supported through bearing. 250 mm spindle travellifting gear box:new oil bath lifting gear box is having its shaft supported through bearings not bushes and thescrew is supported through taper roller bearing. Thus bearings and oil bath gives smooth runningof worm-gear with extended life. Also the heavy duty screw of 35 mm dia and gunmetal nut isheaving 3 long guide. Structure:column bracket is having 440 mm (approx 17 ) long guide on heavy duty 170 mm column. Column is having through rib inside with long bottom for greater rigidity. base plate is heavily ribbed at the bottom side for making sturdy foundation. drill head is made 250 mm (10) wide to suit 225 mm long spindle travel for giving wide supporton arm and making best combination of length and width. better design of arm as complete rectangular cross section of (230mm x 140mm) (9 x 5 )works as highly rigid channel eliminating vibration easily. overall weight of the machine is approximately 950/- kg giving far most rigidity to the machine

R25 25 mm Cap. Radial Drill Machine with Fine FeedSpecification of Pillar Drill Machines: Description R25Capacity Drilling In M.S. 25Drilling in C.I. 32Tapping in M.S. 15Drilling Head Spindle Hole Taper MT-3Spindle Travel 175Spindle Speed (RPM x Steps) 105-2651 x 8Diameter of RAM 72Auto feed Range ( mm x rev) Fine FeedWorking Range Max/Min Distance Spindle Nose to Base 860/100Max/Min Distance Spindle Center toColumn640/330Max. Drilling Radius 705Machine Measurement (L x B x H) 930 x 580 x 1750Diameter Of Column 130Work Table 265 x 200 x 200Power Drill Head Motor 1 HP/1440 RPMElevating Motor 0.5 HP/1440 RPMHead Motor V-Belt B-40Lifting Motor V-Belt B-22/B-23

No Description DC - 410 Capacity Drilling In Mild Steel 42 ( 1 5/8") Drilling in Cast Iron 50 Rough Boring in Mild Steel 60 Tapping in Mild Steel 25 Drilling Head Spindle Taper MT-4 / MT-5 Spindle Travel 225 Spindle Speed (RPM x Steps) 12 steps60, 90, 115, 165, 200, 290, 340, 480, 575, 825, 1005, 1510 Diameter of RAM (Quill) 78 No. of Spindle Auto feed Ranges (MM/REV) 6 steps0.1, 0.15, 0.20, 0.27, 0.33, 0.52 Working Range Max / Min Distance Spindle Nose to Base 1225 /450 Vertical Travel of Arm 775 Max / Min Distance Spindle Center to Column 1025 / 275 Horizontal Travel of Arm 750 Max Drilling Radius 1137 Machine Measurement (LxBxH) 1600 x 850 x 2270 Diameter of Column 225 Work Table 500 x 450 x 400 Coolant Tank 770 x 430 x 14550 Liters Power Drill Head Motor 2 HP(1.5 KW) 960/1440 RPM Elevating Motor 0.75 HP(0.56 KW) 960 RPM

Specification of - P40AA and P40BA - Column Drill Machines:Description P40AA P40BACapacity Drilling In M.S. 40 40Drilling in C.I. 45 45Tapping in M.S. 25 25Rough Boring M.S. 75 65DrillingHeadDrive of the Spindle 9 Speed Oil BathGear Box4 Step Cone Pulleyand Back gear TypeSpindle Hole Taper MT-4 MT-4Spindle Travel 250 250Spindle Speed (RPM x Steps) 88-1404 x 9 80-2600 x 8Diameter of RAM 78 78Auto feed Range ( mm / rev) 2 / 0.05 & 0.09 2 / 0.05 & 0.09WorkingRangeMax. Distance Spindle Nose to Base 920 920Distance Spindle Nose to Table 530 530Distance Spindle Center to Column 345 345Table Size 450 x 455 450 x 455Machine Measurement (L x B x H) 880 x 675 x 1850 880 x 675 x 1850Diameter Of Column 130 130Power Motor 2 HP/ 3 HP 2 HPV-Belt B-33 x 2 B-79