D K Corporation

MG Road, Indore, Madhya Pradesh

We are offering aqua plus emulsifier. diko - aqua plus" (for water addition up to 30% to enamel and primer) to reduce production cost of primers & enamel, water is incorporated to the system. It is not difficult to corporate water to the system, but, it is quiet difficult to maintain properties of your finished product like viscosity, gloss, drying time, stability of enamel .with the use of emulsifiers, water is incorporated to the finished product i.e. Enamel or primers but it has following adverse effects : increase in viscosity, increase in drying time, loss of gloss. aqua plus provides accurate solution to these problems. features : aqua plus is a blend of additives containing polar and non-polar functional groups. In addition to emulsifier and alcohol it also has protective colloids. apart from reducing the surface tension these colloids encompass the dispersed phase thus preventing coalescence and aggregation due to repulsive forces, this imparts stability to the system. aqua plus is compatible with larger spectrum of alkyds. Water-alkyds bond formed is strong enough to last long. recommended dosage:- for 100 kg batch of enamel or primer(finished / final product): 1. 100 gm. Aqua plus is required for 10 ltr. Water addition. 2. 200 gm. Aqua plus is required for 20 ltr. Water addition. 3. 300 gm. aqua plus is required for 30 ltr. Water addition. direction for use : first complete all the addition of your batch. Addition of aqua plus and water is recommended on finished and final batch. add 100 gm. Of 'aqua plus' to 100 kg. Final/finished batch of primer/enamel under high-speed stirrer, stir for 10-15 minute. Add 10 kg water slowly at rate of 1.5 to 2 liter/min. run the stirrer at least for half an hour after completion of water addition. quantity of aqua plus may be balanced or addition of water may be increased, after conducting trial at laboratory batches. do not add pigment, solvent, resin or drier, once water addition is completed. precaution :- if your resin has higher acid value, balance ph of finished product by using mild alkali with water and avoid use of extenders having calcium contents. If necessary to use inert extenders/minerals having calcium contents reacts with acid and carbon dioxide gas is formed and some time tin container breaks due to gas pressure. For higher addition of water %, selection of alkyd resin is important factor.

We are main supplier of this product.

We are offering defoamer, antifoaming agent. anti foaming agent- defoaming agent. we bring forth the anti foaming agent under the brand name dikoaf-01. The antifoam agent is manufactured using the latest technology applying the advanced formula so as to ensure high level of performance. The manufacturing process is carried out under the strict monitoring of our quality control team. It is easily soluble in hard water and hence can restrict the foam formation in all condition. We are counted on top among the prominent industrial antifoaming agents suppliers based in india. defoamer -defoamer for paints, paper , textile industries, sugar industries, effluent treatment plant. a defoamer or an anti-foaming agent is a chemical additive that reduces and restrict foam formation in industrial process liquids. The terms anti-foam agent and defoamer are often mixed up since these are often the same products. It depends on where it is in used. a defoamer is normally used to enhance process speed and reduce other problems raised due to foam formation. It addresses both problems with surface foam and entrained/entrapped air. properties generally a defoamer is insoluble in the working system and has surface active properties. It has affinity to the air-liquid surface where it destabilizes the foam structure. This is causing rupture of the air bubbles and break down of surface foam. featuresdiko-foamfin is good antifoaming (restrict formation of foam) &- defoaming agent (destroy foam formed). antifoaming and defoaming properties depends on foam density, type of foam and size of foam. tips for better results for any defoamer used-diko-foamfin works on "dispersion basis" hence for better result use in diluted form at the grinding stage and part at the finishing stage. prepare 30% diluted solution of diko-foamfin in cold water / hot water with use of stirrer. use as antifoamer: add diluted diko-foamfin solution at grinding stage before addition of extender where foams are likely to be formed. use as defoamer: spray the diluted solution of diko-foamfin whenever foam is noticed. appearance - milky white, viscous paste ph - 6.0 to 7.0 ionic nature - non-ionic chemical nature - dispersed activated diametyl siloxane solubility in hard water - good.

We are offering universal stainer media. "diko - unistain" - universal stainer media(multifunctional pigment dispersing media)while dispersing dry pigment, we expect full value from expensive organic and inorganic pigment and optimum output from the equipments. it acts as a grinding vehicle for highly concentrated dispersions, it wets and deflocculates pigments without causing much foaming which adversely affects the film properties. physical properties:- appearance - yellow / light yellow oily liquid. ph - 6.0 to 7.0 & nonionic in nature. chemical nature - it is blend of proven emulsifiers surfactants and stabilizersstability in hard water & lime - good compatibility - in alkaline & acidic medium we can formulate grinding media or universal stainer media as per your requirement. diko - unistain provides: excellent leveling & dispersing propertiesrapid wetting of pigments and better flow of pigment loading. full chroma & max. Tinting strength development.viscosity stability and avoids setting of pigment. excellent result as "universal / lime stainer media". compatibility with broad range of coatings. act as emulsifier in emulsion paints. it is single pack unique low foaming product. Hence possibly, no need to add meg/deg/peg/t.r.o. testing method:-same as lvidsp it proves that our products eliminates floating of pigment with better dispersing effect. It reduces grinding time & improves flow properties. It is ideal with latter dispersion e.g. Pigment like pthalocynine blue in combination with lemon chrome (bus green shade). guideline formulation: % by wt pigment - 40 lvdisp - 4unistain media - 5thickener (bento clay or any suitable agent) - 0.5defoamer (30% solu. In water)- 1.5 blancfixe (precipitated barium sulphate)-4water & extendersif necessary note:- if you are manufacturing universal stainer from pigment paste take unistain media, defoamer, pigment paste, lvdisp (not necessary) & extender in high speed stirrer and stir it. And finally clean stirrer with unistain media.

We are offering "diko - lvdisp" - levelling cum dispersing agentunique product working as a wetting agent, emulsifier, dispersing agent and levelling agent (a combo of 4 in 1). for oil base paint enamel & water base emulsion (distemper). For printing inks manufacturesmultifunctional pigment dispersing media. for pigment paste manufacturer. While dispersing dry pigment, we expect full value from expensive organic and inorganic pigment and optimum outputfrom the equipments. It acts as a grinding vehicle for highly concentrated dispersions, it wets and deflocculates pigments without causing muchfoaming which adversely affecting the film properties. definition of dispersing agent :-a surface active agent added to the suspending medium to promote uniform & maximum separation of extremely fine solid particles often of colloidal size, application include wet grinding of pigments. Properties :-appearance : light yellow/ brownish oily liquidph : 6.0 to 7.0 & nonionic in naturechemical nature : it is blend of proven emulsifiers surfactants , polyacrylates and stabilizers . Hlb value : 13.87stable in hard water & lime . Compatibility in alkaline & acidic medium. Diko - lvdisp provides: excellent leveling & dispersing properties. rapid wetting of pigments and better flow of pigment loading. full chroma & maximum tinting strength developments. viscosity stability and avoids setting of pigment. excellent result as "universal / lime stainer media". compatibility with broad range of coatings. act as emulsifier in emulsion paints. testing method:-take 100 ml water into 250 ml. Beaker. add small quantity of pigment (alpha blue / green), pigments floats on water surface even after stirring & water doesn't get colored. now add 2 - 3 drops of the products slowly from side edge of beaker, do not stir. please observe breaking of pigment into micro particle without stirring & water gets colour of that pigment. it is called chemical breaking of pigment. It proves that our products eliminates floating of pigment with better dispersing effect. It reduce grinding time & improve flow properties. It is ideal with later dispersion e.g. Pigment like pthalocynine blue in combination with lemon chrome (bus green shade). Recommended dosage: for water base emulsion:- add 0.3 to 0.5 % lvdisp (of total batch) at grinding stage and before addition of pigment. for oil base enamel-: add 0.5 to 0.7 % lvdisp (of total batch) at grinding stage and before addition of pigment. For universal stainer media-: add 4 to 5% at grinding stage along with universal stainer media.