Our Products
Our Complete range of products are Kinematic Viscometer Bath, Storage Boxes, Conical Flask, Speciman Jar and Cement Sampler.
Outer casing is made of double walled Mild steel duly powder coated. The gap between to two walls is filled with ceramic blanket insulation to prevent heat loss. There is a grooved refractory chamber which has kanthal heating element fitted on three side to provide quick heating. Silicon rods are provided in case of high temperature (above 1350C). Temperature can be controlled using a pyrometer or using digital controls. Available in temperature of 1000C, 1200C and above. Inner chambers are of following sizes (in inches):1)4"x4"x9"2)5"x5"x10"3)6"x6"x12"4)8"x8"x12" |
Heavy gauge stainless steel tank sturdily fabricated and bright finished. Provides effective hydro-massage of arms, hips, legs, knees and feet. Mounted on heavy duty 10cm dia four ball bearing castors. Comes complete with removable inside aluminium Seat & Arm rest. Unit is fitted with a motorized turbine ejector and aerator on a spring loaded turbine elevator, digital thermometer, thermostate & immersion heater. Provided with drain pipe for emptying. Inside measurements of tank 90cm long x 50cm wide x 70cm deep. No plumbing required.
Full body `T` shape hydrotherapy tank for hydro-massage. The heavy gauge stainless steel tank, rests on 40cm (16") high tubular stand re-inforced with cross bars. Overall size of the tank is 190cm(75") x 185cm (73") x 93cm (37").Width of the narrow portion of the tank is 91cm (36") and depth inside the tank is 48cm (19"). Comes with Two motorized electric turbine ejectors & aerators with turbine carriages and elevators, Digital Thermometer, adjustable Head-Rest, Body Stretcher and Sitting seat fitted with nylon cloth. Tank is fitted with Two water inlets, One overflow and one Drain fittings. Tank is finished bright inside & painted outside. |
Outer body made of Mild steel duly painted / powder coated. Heavy duty cast iron top. Fitted with Energy Control. Available in round and rectangular top in the following sizes:1) Hot Plate (Round) Diameter 8" inch2) Hot Plate (Rectangular) 10"x12"3) Hot Plate (Rectangular) 10"x16"4) Hot Plate (Rectangular) 12"x18"5) Hot Plate (Rectangular) 18"x24" |
Particle size: Down 10 microns collected on filter paper Flow Rate: 1.0 to 1.5 meter cube/min. free flow Sampling Time Records: By- 24 Hrs Programmable Timer Record true time in Hrs. by Time Totalizer. Voltage Stabilizer: Auto shut off beyond (170270) Volts. Filter: GF/A. (8x10). For Common use. Power Need: 230 V. 50 Hz. 1 Phase A.C. Gaseous Sampling: Provisions for Gas Manifold and Rotameter to allow separate Setting by Pinch valve through Impingers. Rotameter: 0.3 to 3.00 LPM. 2% accuracy. Absorbers: 4 Nos Borosilicate Glass Impingers. ACCESSORIES1. Impinger: 04 Nos.
Particle size: Below 10 microns collected on filter paper and bigger than 10 Micron will be collected in a separate sampling lid, through Cyclone separator. Flow Rate: 0.9 to 1.4m3/min. Automatic Sampling: By- 24 Hrs Programmable Timer, Time Record Voltage Stabilizer: Auto shut off beyond (170270) Volts. Filter: GF/A. (20x25)cms. Whatman Brand. Power Need: 220 V. 50 Hz. 1 Phase A.C. Gaseous Sampling: 0.3 to 3 LPM , Manifold, 4 Impingers with Ice Box. ACCESSORIES1. Impinger: 01 No.2. Filter paper 3. Dust Collector Bottles
Sampling Rate 0.5-1.0 LPM. Diaphragm pump, Flow Adjustment, for needle valve. Operating time 08 hours after charging. NI- Cad. Rechargeable Battery. Charger us in built. Timer. Filter holder in Two size i.e. 25mm and 47 mm Dia. Power required 230 V, 50 Hz. Single phase A/c. Dimensions: (230 X 125 X 215) mm. Sampling Devices: Charcoal Tubes for volatile samples. Impingers Cap. 35 ml. For Gaseous and Filter Holder for SPM.ACCESSORIES Impinger: 04 Nos. Acrylic Holder: 01 No. Filter paper Pkt. Of 100 Sheets |
3.1/2 Digit LCD Display (8mm) Portable, Flash High Accurate Readability Measurement Range: 0.4-30.0 m/s, -108 Km/h, 80-59 10 f/min, 0.8-58.3 Knots with Data hold function.
These are double walled cylindrical units with outer made of M.S. sheet duly enamel painted and Inner made up of heavy gauge S.S. Sheet. Gap between the two walls is duly filled with high grade glass wool to avoid thermal loss. Temperature range from 50 C to 150 C is Controlled by heavy duty thermostat with an accuracy of 1 C. It is capable of withstanding a high vacuum. Provided with vacuum gauge, see through transparent window of toughened glass and one shelf. To work on 220/230 volts A.C. supply. But without Vacuum pump. Available in following sizes:a) 200 x 200 mm b) 250 x 250 mmc) 250 x 300 mm d) 300 x 300 mm e) 300 x 500 mm
With Microprocessor based programmer- 12 x 250 ml. Other sizes also available.
With Plastic Bucket. Available in following capacity:5 Ltr., 7.5 Ltr., and 12 Ltr.
Driven by Diesel or Petrol / Kerosene Engine, Diamond wheel of 300mm dia., suitable for a cut of depth unto 110 mm is supplied with standard outfit. The trolley on which the engine is fitted also has a water rank which supplies a stream of water to keep the cutting blade cool during the operation. Adjustment to control depth of cut is also provided. A safety Guard is provided over the diamond wheel. Diamond wheels up to 600 mm dia., can be supplied at extra cost.
Micro ammeters, milliammeters, and ammeters available in three sizes: 72x72mm, 96x96mm, and 144x144mm. Current range available from 50A to 1000A
This viscometer bath is used to maintain the correct constant temperature for estimating kinematic viscosity of oils and petroleum products. The tank is made out of high grade SS. This tank is fitted with toughned Glasses in the front & rear sides to give a clear view of specimens kept inside. Temperature is controlled by precision contact thermometer or Digital electronic temperature controller from 5C above room temp. up to 99C with an accuracy of 0.1C. All controls are provided on front side panel for easy operation. A FHP motor driven stirrer provided for circulation of water in the bath. Suitable to operate on 220 V A, 50 Hz mains. Available in following two chamber sizes:1) 12"x9"x12" (can accomodate 4 viscometers)2) 12"x12"x12"(can accomodate 6 viscometers) |
These Draining Racks provide an excellent option for post wash draining of tubes & bottles in the laboratory. The back plate has 20 holes into which pegs are tightened with the help of screw nuts. Bottom of the rack is provided with a tray which collects all the waste water drained down which can further be collected in a container via drain tube. This rack does not rot, stain or rust. Material : Acrylonitrile Butadiene Styrene / Polycarbonate
SS body, wall type or table type. Fitted with heavy duty elements. Available in various capacities from 2 Ltr/hour to 20 Ltr/hour |
For visual colour evaluation under different Light Sources namely D-65, D-75 TL-83, TL-84, CWL, UL-30, Illuminant A, Filament Light & U.V Available in electrical and Electronic model.
These Storage Boxes, made of Polypropylene, prove to be an excellent option for storage of different powdered reagents & other material in the laboratory. Square shape of these boxes help in saving shelf space. Available in two different sizes, these boxes have polypropylene caps, are autoclavable, provide good chemical resistance & heavy duty service.Material: PolypropyleneAvailable in 250ml, 500ml, and 1000ml
Also called Mould Vibrator Or Mortar Cube Vibrator.Concrete moulds are easily cast by using a tamping bar or a vibrating table. However air tapped in cement mortar paste can not be thus removed while casting cement mortar moulds. Easy method is to impart greater vibration of lesser amplitude to the mould while casting. This is achieved in a vibrating machine. Vibration machine is used for the preperation of mortar cubes for the determination of compression strength of ordinary and rapid hardening Portland cement, low heat portland cement, portland bleast furnace cement and high alumina cements.The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an intergral bottom part of the frame. The centre of gravity of the assembly is brought to the centre of the eccentric shaft or within a distance of 25mm mould. The frequency of vibration is 12000 400 vibration per minute. Supplied complete with on 7.06cm cube mould with loose base plate, a time switch 0-5mins x 1min and certificate of vibration from a standard laboratory.Spares : Set of Springs, Belt and Belt guard.
Made of Polypropylene, these cone-shaped flasks are rigid, translucent & autoclavable. The screw cap keeps the contents of the flask contamination free and makes the flask leak proof. Threads should be disengaged before autoclaving. Available in 100ml, 250ml, 500mlMaterial: Polypropylene
Magenta Box is very often used in tissue culture & agricultural research experiments. Main body of this box is made of tough & transparent Polycarbonate, which provides excellent view of the contents inside while the cover, is made of Polypropylene. This autoclavable box is square in shape giving itself a space saving feature.Material: Polycarbonate / Polypropylene
These transparent Specimen Jars, used for preserving different specimens in the lab are provided with a cap that fits in tight. These jars provided excellent protection to the species preserved in it. Size 50 mm x h 200 mm
These Clamps are moulded in Polypropylene making it completely corrosion-proof. The spring-loaded jack in the middle provides a vice like grip to the Burette and prevents it from slipping. Two tapered wedges are provided to ensure firm grip on rods having dia 1/2" or 3/8". Available Single and Double type. Material: Polypropylene |
Made from polypropylene, these disposable containers are used for collecting samples of sputum or urine etc. Graduated on the outer surface, these containers have cap that works in a press & fit manner & make these containers leak proof. These disposable containers are E.T.O. sterilized.Material: PolypropyleneAvailable in 25ml and 50ml
To give accurate cut area of 1/100 of a square meter. Supplied with rubber pad and blades
These Carboys, made of polypropylene, are much lighter than glass. These autoclavable, dependable & durable Carboys are provided with wide handles making it convenient while carrying or pouring purposes. Available in 10Ltrs & 20Ltrs.Material: Polypropylene
This is a brass tube approximately 53cm long and 2.8cm I.D. with a wooden handle. Total length approximately 73cm. The tube has the sharp angular edge, which conveniently pierces cement bags. An air hole of approximately 3mm dia is drilled on the near handle. Total sample collected at one time is 300cm approximately.
Thermoplastic and Elastromeric insulation & sheath exposed to heat are subjected to many types of physical and chemical changes. The severity of exposures, both in temp & time, determines the extend & type of change that takes place. This test makes an assessment of change in tensile strength and elongation of materials on subjecting them to accelerated ageing in air.Oven designed to provide 8-20 changes of air per hour, at controlled temperature and extended duration up to 72 hours or longer. Hydraulic thermostat for an accuracy better than 2C.Conforms to IS:10810 (Pt-II), IS:5831Facility for fixing hour meter.Also available four chamber model with individual rotatometer, digital/PID controller & hour meter for bulk testing.
These Water distillers produce highly treated and disinfected water for laboratory usage. The distillation process removes minerals and microbiological contaminants and can reduce levels of chemical contaminants. A water distiller works by boiling water into water vapour, condensing it and then returning it to its liquid state. It is collected in a storage container. Made of heavy gauge stainless sheet inside and outside, with immersion type heaters. The still provides continuous supply of pyroxene free distilled water and is equipped with brackets for wall mounting plug and cord and connector. Available in following capacities:1) 2 Ltr/hour (wattage 2KW)2) 4 Ltr/hour (wattage 4KW)3) 6 Ltr/hour (wattage 4.5KW)4) 8 Ltr/hour (wattage 6KW)
High Voltage Test Sets are specially designed for testing cables, control panels, electrical installations, underground cables etc. as per IS specifications. These high voltage test sets are manufactured by a team of Electrical Engineers. During manufacturing, each unit is tested at various stages, thus maintaining strict quality control.Instruments are air cooled, oil cooled as well as air and coil cooled combined. Generally for wire and cable industry as per IS:694, AC high voltage test set having capacity 5/10 KV, 10 KVA As per IS:694 and 1554 AC High Voltage Test set capacity having 22 KVA. |
Used with Whirlpool Baths for Lower Leg & Foot hydro Massage. Broad based tubular steel frame chair is fitted with foam padded, revolving, Seat and Back for height adjustment. Height is adjustable from 80cm to 100cm. Comes with rubber treaded foot step. Fitted with four wheels of 5cm dia. Finished oven baked.
Used with Whirlpool Baths for arm and hand hydro massage. Revolving Seat is adjustable in height from 40cm to 55cm. Painted tubular steel construction, fitted with upholsteres seat and back. |
This instrument is used for determination and checking of bitumen percentage in bituminous mix, the mix is added with a solvent and dissolved bitumen is removed by centrifugal action. Consists of a removable aluminum rotor bowl, capacity 1500 gms. This shaft and thus the bowl is rotated fast manually by enclosed gears in the cast body and handle. Solvent is introduced during the test through the holes in the cap of the housing. A drain is provided to collect dissolved bitumen coming out of the rotating bowl and getting collected in the housing.
Available in following sizes:20 X 40 cm26 X 47 cm31 X 57 cm
Suitable to Cut / Drill cores of Concrete, Rocks, Stones, Tiles or the similar material. The machine is suitable for care samples of size upto 150mm diameter with the help of thin walled Diamond Bits which are at extra cost. The machine has sturdy base with pillar support in which rack & pinion is provided for adjustment in height and penetration assembly. The leveling screws are at the base. For gripping the damply in positions suitable grips are provided. A suitable electric motor, standard make is fitted in the machine with cooling arrangement with water. The base frame is also fitted with wheels for ease of transportation.Dimension approx. are as under :Height : 1300mmBase : 600 x 1200mmHead travel on rack : 350mmDrill Speeds : 900 RPM for soft samples and 350RPM for hard samples.Water Swivel : Built in the machines.Suitable for 230 volts AC, single phaseAccessories : 1. Thin wall diamond bits 2. Core Barrel.
Available in 1 Ltr., 1.5 Ltr., and 2 Ltr. capacity
Available in following sizes (in inches):6" x 4", 6" x 6", 8" x 5", 8" x 8", 9" x 5", 9" x 9", 11" x 5", 11" x 9", 12" x 9", 12" x 10", 12" x 12", 14" x 5", 14" x 9", 14" x 10", 14" x 12", 15" x 9", 15" x 10", and 15" x 12" |
Available in following sizes (LxW) Inches:8"x 3" and 16"x4"
Available in following sizes (Dia):23 cm, 26 cm, 28 cm, 30 cm, 32 cm, 35 cm, 40 cm |
Available in following sizes (L inches):6", 8", 10", 12" |
Proving rings are used for load measurements and are used in outfits of a number of Soil / Cement & Bitumen Testing Equipments like Direct Share Test Apparatus, Triaxil Share Test Apparatus, CBR Test, Unicontained Test, Marshall Test etc. They are made out of special steel carefully forged to give maximum strength and machined to give highest sensitivity combined with stability to ensure long life and accuracy. When Compressive or tensile load is applied within the elastic range, the proving rings get temporarily deformed. This deformation is measured by a sensitive dial gauge fixed co-axially at the center of proving ring. The dial gauge readings thus obtained versus load applied enable the operator to find out unknown load, just by noting the dial gauge reading for unknown load. The proving rings have high elasticity and on removing load they regain their original shape provided they are loaded in their elastic limits.A Dial gauge and plunger anvil are mounted on brackets clamped to the ring body. The dial gauge is held perfectly rigid without the remote chance of shifting due to inadvertent shocks or pressures exerted on it. The dial gauge plunger rests on an adjustable anvil. Proving Rings , from 50 kg to 1, 00, 000kg capacity provided with 1/2 inch B.S.F female threads. Loading bosses and a loading ball nipple and steel ball are supplied with each rings. Rings of capacity over 25000kg (or 25 Tonnes) are not thus threaded. Each ring is individually calibrated and supplied with works calibration chart and a carrying case.
This is used as timesaver device to measure deflections of flexible pavements. The light weight instrument is supplied in two parts for assembling on site with easy hand tools. In use one end of the beam rests at a point under investigation while the beam is pivoted at the centre. The free end carries a dial gauge to record the deflections. The other end is kept on a stable platform. The beam ratio is 2:1 which magnifies even small deflections. Supplied with a dial gauge 0.01 x 25mm. This is a light weight dismount liable instrument and easy to carry.
This is used for determination of in situ dry density of natural or compacted fine-grained soil, free from aggregates. A cylindrical cutter is used to extract a sample of the soil with the help of a dolly and rammer. From the weight, density and the moisture, and dry density of the soil is readily calculated.It consists one each of : Cylindrical core cutter made of steel, 127.3 mm long and 100mm internal diameter. Steel Dolly, 25 mm high with a lip to enable it to be located on top of the core cutter. Rammer with detachable steel rod.Spare, Optional Extra and Accessories: 1) Cylindrical core cutter 100 mm I.D. x 175 mm long.2) Cylindrical core cutter 100 mm I.D. x 175 mm long.3) Cylindrical core cutter 100 mm I.D. x 175 mm long.4) Dolly.5) Test form pad of 50.
This intelligent automatic capsule filler is applied in medical industry for the filling of hard capsule medicine. It can be used to fill machine made hard capsules ranging from No. 00 to No 4. The filling materials include powder, granule and tiny pellet medicine.Out Put Capsule / Minute:Up to 40, 000 per/hour For Powder Filling.Up to 32, 000 per/hour For pellet Filling.Capsule Size: 00-0-1-2-3-4 Power Supply: 415 V, 3 Phase, 50 Hz A.C.
Available in following sizes (LxW) Inches:8" x 6" 9" x 6" 10" x 8" 11" x 7" 11" x 9" 12" x 8" 12" x 9" 12" x 10" 14" x 10" 15" x 12" 18" x 12"
Available in following sizes (dia):7.5 cm, 10 cm, 12 cm, 15 cm, 18 cm, and 20 cm
Available in various models with choice of single loader / double loader / digital panel / PLC system / automatic or manual capsule closing system
Used for sampling aggregates, ores, refractory materials, pigments, powdered coal, soap, cement, etc. It consists of a sheet metal box mounted on legs and fitted with a series of chutes of equal width which discharge the material alternatively in opposite directions into separate pans. The chutes of the riffle are steep enough to allow rapid flowing of the material. It has 14 chutes of 13mm width and is complete with receivers.Also available with 16 chutes of 25mm width, complete with two receivers.
Available in 1 Ltr., 1.5 Ltr., and 2 Ltr. capacity