Divine International

Sadar Bazar, Delhi

Wavelength Range: 400 - 700 nm [8 Glass Filters]
Peak wavelengths: 400, 490, 520, 540, 590, 620, 650, 700 nm
Minimum Volume: 1.0 ml
Light Source: 6V, 10 W, Tungsten Filament lamp
Test Tubes: 10 mm (Inner)
Detector: Silicon Photodiode
Display: 2 digits seven segment display

This transparent polypropylene cap for Test Tubes Proves to be an excellent protection to the contents to the tubes. The grooves inside the cap tighten the fitting on the tube while the outer grooves would hold identification labels. The built in seal ring would set in the tube making the combination a leak proof one. Suitable for Test Tube 25mm

This is a fast release pipetting device for precise pipetting & zip-quick emptying. The Knurled thumbwheel can be rotated to draw up or dispense liquids while the releaser may be pushed in for zip-quick emptying. The moulded chuck has a silicon rubber collet inside to hold various pipettes of standard sizes. It resists acids & alkalies & can be easily disassembled for through cleaning.

Material: Acrylonitrile Butadiene Styrene
Available in following capacities:
2 ml, 10ml, 25ml

Most versatile for Biochemical Oxygen Demand determinations. Castor wheel mounted cabinet is double walled with inner chamber of aluminum or S.S. and outer wall of M.S. Sheet duly degreased and pre treated with primers for rust proofing duly painted with attractive stove enamel or powder coated . The gap between the outer and the inner wall is filled with special grade glass wool to prevent thermal losses. Triple walled back of unit is fitted with two air circulation fans for maintaining temperature uniformly throughout the chamber. Full view inner glass/perspex door permits inspection of specimens, without disturbing the chamber temperature. Lock and Key arrangement is provided in the double walled outer door. Unit is fitted with door operated illumination lamp inside the chamber. Refrigeration unit is consists of a sturdy compressor/cooling kit. The front panel is provided with separate indicator lamps for main, heating and incoming voltage. Supplied complete with 3 shelves, cord and plug to work on 220/230V A.C. supply. Temperature from 5 C to 60 C is controlled by SOLID STATE ELECTRONIC DIGITAL TEMPERATURE INDICATOR-CUM-CONTOLLER, with an accuracy of 0.5C. Available in following Inner Chamber sizes:
a) 455x610x410 mm (4.0 Cu.ft., 112 Ltrs)
b) 505x830x415 mm (6.1 Cu.ft., 171 Ltrs)
c) 570x875x550 mm (10 Cu.ft., 280 Ltrs)
d) 650x900x550 mm (12 Cu.ft., 336 Ltrs)

Display: Array of 10 LED`s in line
Sample Size: 1-50 mg of water
K.F. Dispensing Resolution: 0.05 ml
Indication: RUN ADD END Display in Auto Mode
Detection: Current Sensing by electronic control
K.F. Flow Highly sensitive sloenoid control volve for automatic control of K.F. Reagent.
Measuring Electrode: Dual Platinum Electrode.
Titration Cell: Air tight 200 m glass vessel
End Point Delay: 30 seconds
Buzzer: Yes
Timer: Adjustable Timer
Stirrer: Variable speed magnetic stirrer with On/Off control
Burette: Pressure filling auto zero burette with 0.05 ml resolution
Power: 230 VAC 10% 50 Hz AC
Provided with following accessories: Burette (Clear Glass) 10 ml, Reservoir Bottle 500 ml, Rubber Belllow for Pumping Air, Titration Cell 200 ml, Dual Platinum Electrode, Teflon Coated Magnetic Stirring Capsule, Nozzle, Moisture Trap with Rubber Tubing, Instruction Manual

These non-corrosive, moulded Retort Stands provide excellent replacement for the metal ones. Even the metallic rod has a polypropylene covering making it non-corrosive. The rod measuring 12.5mm x 750mm can be screwed into the heavy base giving way to a perfectly stable Retort Stand.
Material: Polystyrene / Polypropylene
Available in following sizes:
255x150mm-Side Hole
300x200mm-Centre Hole
300x200mm-Side Hole

These sets consist of moulded balls of different colours and sizes along with connecting lugs of different sizes. These sets are very helpful in modelling different organic & Inorganic compounds.

SENIOR SET: This set consists of 150 lugs & 370 balls of prescribed colours and sizes packed in a moulded box having separate space for every particular colour & size of ball.

JUNIOR SET: This set consists of 30 connecting lugs and 75 balls of different colours and sizes.

This autoclavable Stand is perhaps the most commonly used Test Tube Stand in various laboratories. For better visibility, this 6-place rack is end supported by 2 columns. The top plate has 2 holes for holding 25mm dia test tubes, four holes to hold 16mm dia tubes where as the base has corresponding hemispherical well. It also has six vertical pins fro drying tubes.

Another option available in this section is, a test tube stand in which all the holes in the top plates can hold 25mm dia tubes.

Available for following two sizes of tubes:
1) 16mm & 25mm Tubes
2) 25mm Tubes

Moulded in Polypropylene, this Staining Box helps in staining, fixing, de-staining and handling fragile electrophoresis gels and membranes. Box as well as cover will resist temperatures from -70 C to +70 C. The LDPE plug provides leak proof seal and allows easy liquid drainage. Size 125 x 125 x 50 mm

Magenta Box is very often used in tissue culture & agricultural research experiments. Main body of this box is made of tough & transparent Polycarbonate, which provides excellent view of the contents inside while the cover, is made of Polypropylene. This autoclavable box is square in shape giving itself a space saving feature.

These ELISA/ASSAY plates are made of optical clear, non-toxic Polystyrene. These plates with 96U Bottom or flat bottom wells bear alphanumeric index. Uniform placement of all the wells facilitate use of multi channel pipettes. These plates packed individually are available non-sterile as well as radiation sterilized.

These incubators are double walled units with outer chamber made of M.S. sheet duly enamel painted with inner chamber made up of anodized aluminum or S.S. sheet of SS-304 grade. The gap between inner and outer chamber is filled with high grade glass wool to avoid thermal losses. Beaded heating elements are placed in ribs, at bottom and sides. Inner chamber is provided with ribs for adjusting perforated shelves to convenient height. The door is fitted with glass viewing window to facilitate inspection of sample without disturbing the test temperature. Temperature is controlled by hydraulic type capillary thermostat from ambient to 70 C 0.5 C An L-shaped prismatic thermometer is fitted to unit for reading the chamber temperature. To work on 220/230 volts A.C.supply. Available in following Inner Chamber (W x D x H) sizes:
a) 300x300x300 mm (28 Ltrs.)
b) 355x355x355 mm (45 Ltrs.)
c) 455x455x455 mm (95 Ltrs.)
d) 455x455x605 mm (125 Ltrs.)
e) 605x605x605 mm (224 Ltrs.)
f) 605x455x910 mm (252 Ltrs.)
g) 605x605x910 mm (336 Ltrs.)

These Polypropylene Petri Dishes are clear, unbreakable & autoclavable.
Material: Polypropylene
Available in 50mm, 75mm, 100mm, 125mm, 150mm

This Coplin Jar made of Polypropylene can hold 10 slides of the size 1"x3" back-to-back. The interior of the Coplin Jar is grooved in a way to hold slides in erect position. Domed & shallow thread screw cap provides protection to the slides.

This bath is suitable to maintain constant desired temperature for heating flasks in Chemical Laboratories. Bath is double walled inside made of stainless steel & outer body made of mild steel sheet painted with attractive Epoxy coated. The gap between the walls is filled with glass wool to minimize the loss of temperature. The stainless steel nozzles are provided one for inlet and second for over flow of water. The top of the bath has concentric rings. Available in following sizes:
a) 325*250*100 mm (6 holes of 3" dia.)
b) 325*300*100 mm (9 holes of 3" dia.)
c) 425*325*100 mm (12 holes of 3" dia.)
Also available in single wall

These Beakers, moulded in Polypropylene, have excellent clarity and very good chemical resistance. These autoclavable Beakers have prominently raised graduations on the outer surface. Pouring a solution becomes very convenient because of its tapered spout.
Material: Polypropylene
Available in following capacities:
50 ml, 100ml, 250ml, 500ml, 1000ml, 2000ml

This Burette has a transparent acrylic body and a leak proof stopcock fitted with a self lubricating PTEE plug. Each Burette is individually calibrated to give maximum accuracy. Acrylic body is unaffected by dilute minerals acids & bases except Hydrofloric Acid & Ammonium Hydroxide. The pH range of 1-14 is deal and can be used up to 5% wt/wt of acids or 30% bases.
Material: Polymethyl Methacrylate/ TPX
Available in following capacities:
25ml, 50ml, 100ml

These Desiccators are made of Polypropylene and Polycarbonate. These autoclavable vacuum desiccators can hold vacuum up to 740mm of Hg for 24 hrs. without any greasing. The top dome, moulded in rigid and transparent Polycarbonate, gives a crystal clear view of the desiccant placed inside. The Knurled knob on the top provides easy handling of the dome. The lower part is made of Polypropylene. An internal groove is provided on the flange to hold a silicon rubber O-Ring. The Polypropylene stopcock is fitted with a self-lubricating PTEE plug. This plug works three way i.e. vacuum creation, shutting off & vacuum releasing.

Available in following sizes (Inner Dia):
150mm, 200mm, 250mm, 300mm

These unique boxes are moulded in Polypropylene and are therefore autoclavable. The Box itself is clear providing an excellent view of the tips inside while a table like structure is provided inside to hold the tips. The tip holding spaces are uniformly placed to facilitate the use of multi channel pipettes. The cover is joined to the base through ball catcher hinges and provides excellent protection to the tips.

Available in two types:
1) For 96 Micro-Tips of 2-200 l
2) For 100 Micro-Tips of 200-1000l

The Volumetric Flasks, blown in Polypropylene, are strong, unbreakable and have good contact clarity. These autoclavable flasks are provided with screw caps to prevent leakage.

Available in following capacities:

The Seperatory Funnel is made of Polypropylene, giving it excellent contact clarity and strength. This pear shaped, autoclavable-separating funnel has a leak proof threaded screw cap. The Polypropylene stopcock, fitted with a self-lubricating PTFE plug, is push fitted to the stem of the seperatory funnel.

Needless to say, this Laboratory Tray moulded in Polypropylene is a multipurpose tray that can be used for sterilizing, drying glassware, porcelain ware & other laboratory instruments. These steam autoclavable trays have tapered walls, which prove good for nesting.

Material: Polypropylene
Available in two sizes:
1) 450X350X75mm
2) 375x300x75mm

Capacity: 15 Samples
Sample cap.: 20 ml.
Temperature: Ambient to 400C, +/- 10,
Timer Range: 9.9 Hours. Auto shut off and Buzzer.
Display: LCD display in Temp. And Timer.
Method: As per APHA.
Power: 230 Volts, single phase A/c,
Glass ware: 15 No. Vessels and 15 No. Air condensers
ACCESSORIES
1. Stand for Vessel: 01.
2. Stand for Air Condenser: 01.
3. Cooling Tray: 01.

Adding to the already existing range of autoclavable laboratories trays, is the Utility Tray and as the name suggests this Polypropylene Tray can be utilized for purposes ranging from drying glassware to sterilizing and to store any laboratory apparatus. Size 375X350X130mm

These are sturdy double walled units with outer chamber made of M.S. sheet duly enamel painted with inner chamber made up of anodized aluminum or S.S. sheet of SS-304 grade. The gap between inner and outer chamber is filled with high grade glass wool to avoid thermal losses. Beaded heating elements are placed in ribs, at bottom and sides. Inner chamber is provided with ribs for adjusting perforated shelves to convenient height. Temperature is controlled by hydraulic type capillary thermostat from ambient to 250C 0.5 C An L-shaped prismatic thermometer is fitted to unit for reading the chamber temperature. To work on 220/230 volts A.C.supply. Available in following Inner Chamber sizes(W x D x H) :
a) 300x300x300 mm (28 Ltrs.)
b) 355x355x355 mm (45 Ltrs.)
c) 455x455x455 mm (95 Ltrs.)
d) 455x455x605 mm (125 Ltrs.)
e) 605x605x605 mm (224 Ltrs.)
f) 605x455x910 mm (252 Ltrs.)
g) 605x605x910 mm (336 Ltrs.)

This cell scraper, as the name suggests, provides an excellent option for cell scraping purposes in microbiology.

These measuring cylinders, moulded in Polypropylene, are single piece cylinders. These autoclavable cylinders have raised prominent graduations for easy reading and have excellent contact clarity. The broad base provides good stability.
Material: Polypropylene
Available in following sizes:
10 ml Least Count 0.2ml, 25ml Least Count 0.5ml,
50ml Least Count 1ml, 100ml Least Count 1ml,
250ml Least Count 2ml, 500ml Least Count 5ml,
1000ml Least Count 10ml, 2000ml Least Count 20ml
Material: TPX (Poly Methyl Pentene)
10 ml Least Count 0.2ml, 25ml Least Count 0.5ml,
50ml Least Count 1ml, 100ml Least Count 1ml,
250ml Least Count 2ml, 500ml Least Count 5ml,
1000ml Least Count 10ml