Dhruvi Enterprise

Kandivali, Mumbai, Maharashtra

NOX RUST® VCI 105 S is a Volatile Corrosion Inhibitive Lubricating Oil for use in the preservation of ferrous metal parts in enclosed systems. NOX RUST® VCI 105 S combines the protective properties of a preservative oil with those of Volatile Corrosion Inhibitors.

Features:-

• Based on the proprietary Daubert VCI® Technology and extremely effective in enclosed areas such as fuel tanks.
• Provides excellent Vapour Phase Protection to applied system.
• Compatible with most petroleum fuels and lubricating oils.

Application Areas

• For closed systems such as fuel tanks, storage tanks, cylinders, transmissions, gear housings, clutch compartments, crankcases, hydraulic and cooling circulating systems. It is also used for fogging into shipping cases to protect unpainted auto and truck body sections during shipments.
• NOX RUST® VCI 105 S can be used to advantage for preservation of various farm, building equipment, buses, military & railway equipment

Method of Usage:-
Drive Clutch and Steering Clutch Assemblies Since drive clutch and steering clutch assemblies are subject to corrosion within their compartments during shipment and storage, this problem was overcome by fogging 3% of NOX RUST® VCI 105 S Oil into each chamber and plugging the orifice to retain vapour.

Hydraulic CylindersCorrosion of Hydraulic cylinders can cause leakage. Protection of cylinders and circulating systems is provided by adding 2% NOX RUST® VCI 105 S to the hydraulic test oil. After testing and additional 3% are added.

Diesel and Fuel Injection SystemsTo forestall rust which will foul a diesel injection system, the recommended rate for tanks in 1 or 2 cc per 1000 cc of void space.

Crankshaft CasesTo protect crankshaft, bearings, rocker arms and all surfaces normally lubricated by crankcase oil, 1% NOX RUST® VCI 105 S, by volume, is added to the crankcase oil.

Diesel or Gasoline EnginesTo protect upper cylinder walls and valves in diesel or gasoline engines, 3% of NOX RUST® VCI 105 S are introduced throughout the air filter and sucked into the cylinders by turning over the motor with ignition off.

TransmissionsFor transmissions, 2% NOX RUST® VCI 105 S is added to the lubricant.

CAUTIONNOX RUST® VCI 105 S Oil can be used full strength in systems with ferrous metals only. Where non-ferrous metals are present, NOX RUST® VCI 105 S Oil must be diluted to two percent or less, depending on the metals present.

NOX RUST 311 HM is a very efficient, low viscosity solvent based, rustpreventive oil for protection of both ferrous & non-ferrous metals (especially Aluminum & Zinc). NOX RUST 311 HM provides excellent protection from corrosion in areas of high temperatures and humidity.

Features:-

• NOX RUST 311 HM provides Multimetal protection.
• Does not affect rubber, plastic and painted surfaces.
• Provides thin non-tacky film that does not require removal in most cases.
• Provides high coverage resulting in greater economy.

Application Areas:-For high precision parts (both ferrous & non-ferrous) for domestic & export shipments. Idealfor complete assemblies machines & engines where there is existence of many materials, both metals and non-metals.

Refer to product Safety Data Sheet (SDS) for safety and environmental aspectsProduction of NOX-RUST 311 HM is certified according to the quality management system ISO 9001, the environmental management system ISO 14001 and occupational health and safety management system OHSAS 18001. Whilst the information and figures given here are typical of current manufacturing and conform to specification, variations may occur. No warranty expressed or implied is given concerning the accuracy of the information or the suitability of the products.

For excellent quality Tectyl  Rust Preventive ( Tectyl  506), you can contact us. We are an unsurpassed Supplier and Exporter of  Tectyl  Rust Preventive ( Tectyl  506). The  Tectyl  Rust Preventive ( Tectyl  506) offered is a solvent cutback, wax base, corrosion preventive compound.  Tectyl  Rust Preventive ( Tectyl  506) is excellent for long term protection of metallic surfaces against corrosion in either indoor or outdoor exposure and during domestic and international shipments. It cures to dry firm amber, waxy and translucent film.

Long Term Protection :  Tectyl  506 is formulated for easy application by spray, dip or brush.  Tectyl  506 provides outstanding external protection of machinery, machinery, machine rolls, machine tools, automotive parts, dies, tubing, and spare parts.  Tectyl  506 has a dielectric (insulating) strength of approximately 1000 volts per dry mil of film thickness and therefore protects electrical connections and helps prevent galvanic corrosion.

Surface Preparation : The maximum performance of  Tectyl  506 can only be achieved when the metal surfaces, to be protected, are clean and dry. Remove dirt, rust, scaling paint and other contaminants before applying 506.

Caution (Combustible) :  Tectyl  506 cures by solvent evaporation. Keep away from heat, sparks and open flames. Use with adequate ventilation. If applied to the interior of an enclosed vessel adequate ventilation is required for cure and to ensure against formation of an explosive atmosphere. For further information, consult Valvoline Cummins Ltd. Refer to Valvoline Cummins Ltd Material Safety Data Sheet for health and safety instructions.

Designed to protect parts in indoor and covered storage, our Tectyl  Rust Preventive ( Tectyl  502 C) has huge demand in the market. We are reliable Suppliers and Exporters of  Tectyl  Rust Preventive ( Tectyl  502 C). The  Tectyl  Rust Preventive ( Tectyl  502 C) offered is a solvent cutback, soft wax base, corrosion preventive compound. Our  Tectyl  Rust Preventive ( Tectyl  502 C) is approved under military Specification Mil-C-16173D, Grade 2.

Long Term Protection :  Tectyl  502C is suited for application by either spray, dip or brush. Tectyl  502C is designed for long-term indoor And limited outdoor protection of pipe, machinery, instruments, bearings and spare parts.  Tectyl  502C can be used as a preservative for lubrication and fuel systems of gasoline and diesel engines for storage or export. The dry film is transparent, soft and self-healing.

Surface Preparation : The maximum performance for  Tectyl  502C can only be achieved when the metal surfaces, to be protected, are clean and dry. However,   Tectyl  502C is effective on lightly rusted surfaces.

Caution : (Combustible) :  Tectyl  502C cures by solvent evaporation. Use with adequate ventilation. Adequate ventilation is required for cure and to ensure against formation of an explosive atmosphere. THE PARTIALLY CURED FILM SHOULD NOT BE EXPOSED TO IGNITION SOURCES SUCH AS FLARES, FLAMES, SPARKS, EXCESSIVE HEAT OR TORCHES.

Widely used for vehicle rust proofing and protection of machinery and parts in storage, our  Tectyl Rust Preventive ( Tectyl 506 EH) has quality certification. Our company is a nonpareil Supplier and Exporter of  Tectyl Rust Preventive ( Tectyl 506 EH). The  Tectyl Rust Preventive ( Tectyl 506 EH) offered is a solvent cutback, general purpose corrosion preventive compound. Customers can purchase the  Tectyl Rust Preventive ( Tectyl 506 EH) at industry leading rates.

Surface Preparation : The maximum performance of  Tectyl 506EH can only be achieved when the metal surfaces, to be protected, are clean, dry and free of rust, oil and mill scale. Korea Houghton Corp. recommends that the metal substrate temperature be 50-95°C (10-35°C) at the time of product application.

Application : Tectyl 506EH is formulated to be used as supplied. Ensure Uniform consistency prior to use. Continued stirring is generally not required. If the product thickens due to cold storage or loss of solvent during use, contact Korea Houghton Corp. DO NOT THIN  Tectyl 506EH. Incorrect thinning will affect film build, dry time and product performance. Korea Houghton Corp. recommends that the ambient and product temperature be 50-95°C (10-35°C) at time of application.  Tectyl 506EH can be spray or dip applied. DO NOT FREEZE  Tectyl 506EH.

Caution : Adequate ventilation is required for cure and to ensure against formation of a combustible liquid. THE PARTIALY CURED FILM SHOULD NOT BE EXPOSED TO IGNITION SOURCES SUCH AS FLARES, FLAMES, SPARKS, EXCESSIVE HEAT, OR TORCHES. For further information, consult VALVOLINE CUMMINS LIMITED.

Tectyl  Rust Preventive (Tectyl  846) is a solvent cutback, wax base, general purpose, and corrosion preventive compound. The company has cemented its presence among the prominent Suppliers and Exporters of Tectyl  Rust Preventive (Tectyl  846). Our Tectyl  Rust Preventive (Tectyl  846) is excellent for long term protection of metallic surfaces against corrosion in either indoor or outdoor exposure. It widely for the protection of machinery, machine rolls/tools, automatic parts, dies, tubing, and spare parts.

Surface Preparation : The maximum performance of Tectyl  846 can be achieved only when the metal surfaces to be protected are clean, dry and free of rust, oil and mill scale. Valvoline recommends that the metal substrate temperature be 10-35 °C at the time of product application.

Application : Tectyl  846 is formulated to be used as supplied. Ensure uniform consistency prior to use. Continued stirring is generally not required. If the product thickens due to cold storage or loss of solvent during use, contact Valvoline. DO NOT THIN Tectyl  846. Incorrect thinning will affect film build, dry time and product performance. Valvoline recommends that the ambient and product temperature be 10-35 °C at the time of product application. Tectyl  846 can be applied by airless spray or brush. Tectyl  846 can have a shelf life of 3 years minimum.

Caution : Adequate ventilation is required for cure and to ensure against formation of combustible liquid. THE PARTIALLY CURED FILM SHOULD NOT BE EXPOSED TO IGNITION SOURCES SUCH AS FLARES, FLAMES, SPARKS, EXCESSIVE HEAT OR TORCHES. Refer to Valvoline Material Safety Data Sheet for additional handling and first aid information.

Tectyl  Rust Preventive (Tectyl 511 M) is a solvent cutback, water displacing, and oil based corrosion preventive compound. The company shares glorious credentials with the leading Suppliers and Exporters of Tectyl  Rust Preventive (Tectyl  511 M. Our Tectyl  Rust Preventive (Tectyl  511 M) is designed to protect ferrous and non-ferrous industrial parts and transportation components during covered shipment and inside storage. It cures to a light amber colored, transparent oily film.

Surface Preparation : The maximum performance of Tectyl  511-M can be achieved only when the metal surfaces to be protected are clean, dry and free of rust, oil and mill scale. Valvoline recommends that the metal substrate temperature be 10-35 °C at the time of product application.

Application : Tectyl  511-M is formulated to be used as supplied. Ensure uniform consistency prior to use. Continued stirring is generally not required. If the product thickens due to cold storage or loss of solvent during use, contact Valvoline. DO NOT THIN Tectyl  511-M. Incorrect thinning will affect film build, dry time and product performance. Valvoline recommends that the ambient and product temperature be 10-35 °C at the time of product application. Tectyl  511-M can be applied by airless or air mixing spray or dipping.

Caution : Adequate ventilation is required for cure and to ensure against formation of combustible liquid. THE PARTIALLY CURED FILM SHOULD NOT BE EXPOSED TO IGNITION SOURCES SUCH AS FLARES, FLAMES, SPARKS, EXCESSIVE HEAT OR TORCHES. Refer to Valvoline Material Safety Data Sheet for additional handling and first aid information.