Ceramic fiber blankets are manufactured from high quality spun ceramic fibers, which are double needled so as to enhance the physical properties of the blanket, conferring good strength, handling ability, durability & resistance to delaminating. Also, these properties are retained at high temperatures without causing smokes or fumes.

Characteristics 

• Double needled blanket
• Low thermal conductivity
• Low weight compared to other refractory materials
• Low shrinkage
• High tensil strength
• Easy Installation

Applications 

• Lining for furnace, kiln & oven
• Expansion joint & seals for oven, furnace & kiln
• Back – up insulation
• Steam turbine & nuclear insulation
• Pipe insulation & Fire protection

Ceramic Fiber Modules are manufactured by our sedulous professionals, using high-grade material & advanced techniques, thus getting in-tune with the defined industry norms & guidelines. Clients can avail from us a broad assortment of ceramic fiber modules. In the layered construction ceramic fiber blanket and board, anchors lye out to hot face temperature. To overcome this limitation, module system finds application.

Characteristics –

• Resistant to thermal shock
• Flexible & easy to cut & install
• Low thermal conductivity
• High mechanical strength
• Resistant to gas flow erosion
• Asbestos free

Applications –

• Transfer ladle lids
• Petrochemicals (reformers, duct-work pyrolysis heaters)
• Ceramic (Kiln cars, shuttle kiln, tunnel kiln)
• Multi & single stack coil annealing furnace
• Iron & Steel reheating furnace

Availability

Folded Module

folded module is made from pre – compressed fiber blanket. The anchoring system of this module is different from other modules. The anchor hardware consists of an internal yoke in the center of the module & two support tubes. The internal anchor hardware is made of SS wires.

Available sizes – Grade (°C) -

• 1260°C
• 1425°C

Sizes for Folded Module (mm/Pc)

• 150x300x300
• 200x300x300
• 250x300x300
• 300x300x300

Fiber Veener Module

Fiber veener module is manufacturing Veener module as a fast solution of existing refractory & bricks lining to protect the heat loss without any removal of lining. It is a ceramic fiber block which can be place through veener mortar over the existing refractory & bricks lining. Veener module made from compressed multiple blanket strips which provides the advantage of an edge grain configuration.

Available sizes – Grade (°C) -

• 1260°C
• 1425°C

Sizes for Fiber Veener Module (mm/Pc)

• 25x300x300
• 50x300x300
• 75x300x300

Ceramic bulk fibers are made from high purity Alumina, Silica and Zircon. They are resistant to chemical attack and are long and flexible with high refractory properties. Bulk fibers can be needled to form a blanket, converted into ceramic fiber shapes, or blended into liquid binders for coatings and cements.

Characteristics –

• Excellent Thermal & Chemical Stability
• Excellent Thermal Shock resistant
• Resilient to high Tempreatures
• Light weight, low heat storage capacity
• Low thermal conductivity
• Excellent sound absorber
• Asbestos Free

Application –

• Raw Material of secondary ceramic fiber product e.g. blanket, board
• Expansion Joint Seal
• Loose insulating fill for complex spaces & areas where access is difficult

Ceramic Fiber Boards are manufactured from mixture of refractory fibers, special minerals & binders which have low organic & inorganic content. The mixture is vacuum processed into boards which imparts good mechanical strength even at high temperature.

Characteristics –

• Low Shrinkage value
• High Mechanical Strength
• Low thermal conductivity
• Resist to thermal shock
• Unaffected, even when directly in contact with the flow of AI & other non – ferrous metals.
• Short heating & cooling time
• Asbestos Free

Applicability –

• Hot face lining of kiln
• Back up insulation of bricks & cast able lining
• Back lining for ladle cover
• Furnace door insulation
• Damper Sheet

Ceramic fiber blankets are manufactured from high quality spun ceramic fibers, which are double needled so as to enhance the physical properties of the blanket, conferring good strength, handling ability, durability & resistance to delaminating. Also, these properties are retained at high temperatures without causing smokes or fumes.

Characteristics 

• Double needled blanket
• Low thermal conductivity
• Low weight compared to other refractory materials
• Low shrinkage
• High tensil strength
• Easy Installation

Applications 

• Lining for furnace, kiln & oven
• Expansion joint & seals for oven, furnace & kiln
• Back – up insulation
• Steam turbine & nuclear insulation
• Pipe insulation & Fire protection

Ceramic Fiber Modules are manufactured by our sedulous professionals, using high-grade material & advanced techniques, thus getting in-tune with the defined industry norms & guidelines. Clients can avail from us a broad assortment of ceramic fiber modules. In the layered construction ceramic fiber blanket and board, anchors lye out to hot face temperature. To overcome this limitation, module system finds application.

Characteristics –

• Resistant to thermal shock
• Flexible & easy to cut & install
• Low thermal conductivity
• High mechanical strength
• Resistant to gas flow erosion
• Asbestos free

Applications –

• Transfer ladle lids
• Petrochemicals (reformers, duct-work pyrolysis heaters)
• Ceramic (Kiln cars, shuttle kiln, tunnel kiln)
• Multi & single stack coil annealing furnace
• Iron & Steel reheating furnace

Availability

Folded Module

folded module is made from pre – compressed fiber blanket. The anchoring system of this module is different from other modules. The anchor hardware consists of an internal yoke in the center of the module & two support tubes. The internal anchor hardware is made of SS wires.

Available sizes – Grade (°C) -

• 1260°C
• 1425°C

Sizes for Folded Module (mm/Pc)

• 150x300x300
• 200x300x300
• 250x300x300
• 300x300x300

Fiber Veener Module

Fiber veener module is manufacturing Veener module as a fast solution of existing refractory & bricks lining to protect the heat loss without any removal of lining. It is a ceramic fiber block which can be place through veener mortar over the existing refractory & bricks lining. Veener module made from compressed multiple blanket strips which provides the advantage of an edge grain configuration.

Available sizes – Grade (°C) -

• 1260°C
• 1425°C

Sizes for Fiber Veener Module (mm/Pc)

• 25x300x300
• 50x300x300
• 75x300x300

Ceramic bulk fibers are made from high purity Alumina, Silica and Zircon. They are resistant to chemical attack and are long and flexible with high refractory properties. Bulk fibers can be needled to form a blanket, converted into ceramic fiber shapes, or blended into liquid binders for coatings and cements.

Characteristics –

• Excellent Thermal & Chemical Stability
• Excellent Thermal Shock resistant
• Resilient to high Tempreatures
• Light weight, low heat storage capacity
• Low thermal conductivity
• Excellent sound absorber
• Asbestos Free

Application –

• Raw Material of secondary ceramic fiber product e.g. blanket, board
• Expansion Joint Seal
• Loose insulating fill for complex spaces & areas where access is difficult

Ceramic Fiber Boards are manufactured from mixture of refractory fibers, special minerals & binders which have low organic & inorganic content. The mixture is vacuum processed into boards which imparts good mechanical strength even at high temperature.

Characteristics –

• Low Shrinkage value
• High Mechanical Strength
• Low thermal conductivity
• Resist to thermal shock
• Unaffected, even when directly in contact with the flow of AI & other non – ferrous metals.
• Short heating & cooling time
• Asbestos Free

Applicability –

• Hot face lining of kiln
• Back up insulation of bricks & cast able lining
• Back lining for ladle cover
• Furnace door insulation
• Damper Sheet