Our Product / Services
Display Screen
2 Products availableLaboratory Apparatus
2 Products availableTesting Equipment
2 Products availableTables
1 Products availableGPS, Navigation & Tracking Devices
1 Products availableSoftware Development Service
1 Services availableLaptops, Computers & Mainframes
1 Products availableWire Making Machines
1 Products availablePallet Machines
1 Products availableElectrical & Electronic Testing Devices
1 Products availableOur product range contains a wide range of FPGA Mezzanine Card, compact pci, Industry Pack, VXI modules and BrahMos Missile Checkout Equipment
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
Signal Conditioner Card (SC)
Data Patterns utilize a custom form factor connector suitable for use as a plugin modules on carriers in cPCI, VME or VPX standards specially designed for slow speed precision signals.
Switched Mezzanine Card (XMC)
XMC switched Mezzanine Card form factor is used for providing cross-platform functional solutions usable on cPCI, VME and VPX systems, primarily focused on PCI Express based interface. The XMC is derived from the PMC form factor. A very broad range of I/O functionality is provided through XMC modules.
A list of products is given below.
DP-FMC-1002 | Dual Channel 12 BIT / 10 Bit 4 GSPS / 3 GSPS FMC ADC Module | |
DP-FMC-2009 | Dual Channel 14 BIT FMC DAC Module | |
DP-FMC-5001 | 400 MHz Dual Channel 14 BIT FMC ADC | |
DP-FMC-5004 | 125 MHz Quad Channel 16 BIT FMC ADC | |
DP-PMC-1104 | Quad Channel 105 MHz 16 BIT ADC PMC Module | |
DP-PMC-5346 | 2 Channel PCM Frame Sync & IRIG B Reader Module | |
DP-PMC-5535 | Intelligent 3 Node 1553B BC/RT/MT Module | |
DP-PMC-5679 | Rugged Advanced Graphics Engine | |
DP-PMC-5715 | ARINC 708 PMC Module | |
DP-PMC-5736 | PCI Extender Card | |
DP-PMC-5769 | Dual Output Graphics Card | |
DP-XMC-1104 | 2-Channel, 200/250 MHz 16 BIT ADC XMC Module | |
DP-XMC-5007 | Quad MIL-STD-1553B, Dual ARINC 429 and Quad UART Communication Module | |
DP-XMC-5010 | Quad Serial FPDP / Aurora XMC / PMC Module | |
DP-XMC-5775 | 39 Differential I/O or 78 TTL I/O XMC Module |
Modules in compact PCI from Data Patterns are available for Data Acquisition and Control, Simulation, Communication Automatic test equipment, Rugged systems, Fail-safe systems, Computer controlled logic controls, Plant automation and similar requirements. Other I/O functions available from our IP and Mezzanine Module families can be directly integrated into our cPCI systems.
Data Patterns has also pioneered cPCI derivatives such as 9U High Voltage systems, Multiple backplane support with Hot Standby Switchover capabilities. Continuous innovation enables MMI options such as CRT & LCD displays, Keyboards, Pointing devices, Finger print security devices and so on.
A list of products is given below.
DP-cPCI-1197 | 6 Channel Signal Conditioner & Data Acquisition Module For Full 14 Bridge Transducers | |
DP-cPCI-2502 | 16 Channel Isolated Analog Output Module | |
DP-cPCI-2505 | 32 Channel Analog Output Module | |
DP-cPCI-2601 | 6 Channel Function Generator / Flow Simulator | |
DP-cPCI-2709 | 4 Channel Precision Resistance Simulator Card | |
DP-cPCI-3015 | 128 Channel Digital I/O With 6 Channel Counter | |
DP-cPCI-3069 | 64 Channel Isolated Digital Input / Interrupt Output Module | |
DP-cPCI-3096 | 96 Channel Isolated Digital Input / Interrupt Output Module | |
DP-cPCI-3708 | 160 Channel Isolated Digital Output Module | |
DP-cPCI-3780 | 192 Channel Isolated Digital Input / Interrupt Module | |
DP-cPCI-3996 | 64 Channel Digital Pattern Generator And Recorder Module | |
DP-cPCI-4017 | 40 Channel Low Thermal Relay Multiplexer Module | |
DP-cPCI-4032 | 192 X 1 Or 96 X 2 cPCI Low Thermal Relay Scanner Module | |
DP-cPCI-4035 | 32 Form C High Power Relay Module | |
DP-cPCI-4113 | 2 Pole 12 X 4 Low Thermal Relay Matrix Module | |
DP-cPCI-4149 | 192 X 4 / Dual 96 X 4, cPCI High Density Matrix Module | |
DP-cPCI-4158 | 8 Channel 1GHz High Frequency for SBDT Relay Module | |
DP-cPCI-4296 | 3U cPCI 8 Channel ARINC 429 Module | |
DP-cPCI-4305 | 64 Channel Form A High Power Relay | |
DP-cPCI-4341 | Configurable Relay Matrix Module | |
DP-cPCI-4383 | 192 X 1 High Density Relay Multiplexer | |
DP-cPCI-4455 | 24 Channel, 1 Form C 5A Relay Switch | |
DP-cPCI-4509 | 32 Channel, 1 Form C 2A Relay Switch | |
DP-cPCI-4545 | 16 Channel, 1 Form A 15A Relay Switch | |
DP-cPCI-5004 | 24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator | |
DP-cPCI-5031 | Synchro To Digital & Digital To Synchro Converter | |
DP-cPCI-5112 | Quad M Module Carrier | |
DP-cPCI-5121 | Quad IP Carrier Module With Rear I/O | |
DP-cPCI-5202 | Quad IP Carrier Module With Front I/O | |
DP-cPCI-5211 | cPCI IP Carrier Module With Front And Rear I/O | |
DP-cPCI-5400 | 6U cPCI PMC carrier | |
DP-cPCI-5586 | High Voltage Insulation Tester Module | |
DP-cPCI-5664 | Dual Channel MIL-STD-1553 BC/RT/MT cPCI Intelligent Module | |
DP-cPCI-5667 | Audio Analyzer and Digital Audio Bus Module | |
DP-cPCI-5715 | cPCI Based PentiumM SBC | |
DP-cPCI-7497 | PCI Extender Card for cPCI Systems | |
DP-cPCI-7554 | Frequency Response Analyser | |
DP-cPCI-8001 | 9U cPCI Chassis | |
DP-cPCI-8010 | 10U cPCI Chassis | |
DP-cPCI-8100 | Portable cPCI Chassis With 15" LCD Display | |
DP-cPCI-8118 | 4U cPCI Chassis | |
DP-OBC-0453 | DP-OBC-0453 Rugged cPCI PowerPC Processor Module | |
DP-OBC-1011 | Rugged cPCI Communication Module | |
DP-OBC-1122 | Multifunctional I/O Module | |
DP-OBC-3003 | 64 Channel Digital Input and 4 Channel RS422 Module | |
DP-OBC-3006 | 64 Channel Digital Output and 4 Channel RS422 Module | |
Rear I/O | Rear I/O Transition Modules |
Industry Pack (IP) modules are international standards as per ANSI-VITA 4.
These are mezzanine modules of approximately the size of a business card (99mm x 45mm). Featuring a 16 or 32 bit wide I/O interface and 50 user defined I/O pins, these modules are ideal for providing the capability for high density I/O.
IP carriers provide multiple slots on a single carrier. This allows multiple IP modules to be provided on a single slot in a Compact PCI / VME / VXI / PCI card cage.
Industry Pack modules provide some unique advantages in system integration. These include:
A unique advantage of the IP concept is the ability to utilise IP modules in multiple hardware architectures. A typical high reliability project is implemented in Compact PCI or VME or VXI architectures. However, the project is likely to need hardware in advance to carry out simulation or software development and so on. In this case, The IP modules can be procured early, and utilised on low cost PC platforms. Subsequently, the projects can transfer the resources to the final platforms. Developed source code can be easily ported to the final environment.
The layout of the IP board enables mechanical ruggedisation to be easily achieved, enabling vibration and shock resistant applications to be met.
Data Patterns has implemented a range of functions on the IP form factor. These include communication modules, digital I/O modules, special functions such as pulse generation and sensing, resolver inputs and timing generation suited for the special signals found on ships. Some of these products are used in airborne as well as marine applications.
Further functions needed for applications can be developed by Data Patterns in very short time frames, where such a development is appropriate to project requirements.
The use of the IP modules, in conjunction with carriers in standard platforms such as Compact PCI, VXI, VME and PCI enables Data Patterns to implement projects flexibly and quickly.
A list of products is given below.
DP-IP-3039 | 48 Channel Digital I/O IP Module | |
DP-IP-3084 | 48 Channel TTL I/O IP Module | |
DP-IP-3113 | 16 Channel Differential Digital I/O Module | |
DP-IP-4221 | 8 Channel RS422/485 Serial Communication IP Module | |
DP-IP-4299 | 8 Channel ARINC 429 IP Module | |
DP-IP-5208 | 4 Channel Pulse Generator Output IP Module | |
DP-IP-5307 | 8 Channels of Relay Output & 3 Channels of Digital/Octo/Differential Input IP Module | |
DP-IP-5316 | 8 Channel AC/DC Sensing & Counter IP Module | |
DP-IP-5325 | 16 Channel Differential Output IP Module | |
DP-IP-5334 | 1 Channel DC Voltage Detection 1 Channel Syncro Detection 1 Channel Resolver Output IP Module | |
DP-IP-5433 | User Programmable 48 Channel TTL I/O IP Module | |
DP-IP-5532 | MIL-STD-1553 BC/RT/MT IP Module | |
DP-IP-5610 | Dual ARINC 561 Module | |
DP-MM-1105 | 16 Channel 100 KHz Isolated ADC Module | |
DP-MM-1123 | 3 Channel M-Module Strain Gauge Signal Conditioner with Excitation | |
DP-MM-2509 | DC Precision Source | |
DP-MM-2608 | AC Precision Source | |
DP-MM-4411 | Pulse Generator Module |
VXI stands for VME eXtensions for Instrumentation. It is an open standard first developed by five leading Test and Measurement companies in 1987 to standardise a backplane capable of developing open, interchangeable instrument modules that could be used to build Automatic Test Equipment (ATE).
Data Patterns designs and markets a wide range of VXI modules, some of which are listed below. Due to the use of the latest technologies, Data Patterns VXI modules offer the highest I/O density available in the industry today.
Further enhancements of functional capabilities are achieved by the use of VXI IP carriers and VXI M Module carriers. This extends standard functions available from Data Patterns in these mezzanine architectures to the VXI platform.
Data Patterns' VXI modules are utilized in high reliability applications such as Count Down Checkout System for the First and Second Launch Pads at Satish Dhawan Space Centre SHAR operated by Indian Space Research Organisation (ISRO).
A list of products is given below.
DP-VXI-1101 | 64 Channel 100 KHz 16 Bit ADC Module | |
DP-VXI-3099 | 256 Channel Digital Input / Interrupt Output Module | |
DP-VXI-3117 | 128 Channel Isolated Digital Input / Interrupt Module | |
DP-VXI-4017 | 80 Channel Relay Multiplexer | |
DP-VXI-4503 | 80 Channel Relay Switch | |
DP-VXI-5106 | 32 Channel Analog Comparator Module | |
DP-VXI-5124 | VXI IP Carrier Module |
Data Patterns has a strong RF and Microwave engineering capability, featuring a team of enthusiastic engineering talent, substantial investments in RF test and measuring instruments, and an attitude to utilise the latest technologies.
An in-house manufacturing capability and an insatiable demand for fulfilling requirements of Radar, Electronic Warfare and Communication domains, Data Patterns has developed a whole line of building blocks including TR Modules, Up and Down Converters, Power Amplifiers, Transmitters, Combiners and Dividers for specific requirements.
A list of products is given below.
DP-CRF-0500 | DDS Piggy Module, 250 to 660 MHz, BMA Female connector (Wideband, Custom) | |
DP-CRF-2303 | Local Oscillator 2 Module 1.44/1.56 GHz, BMA female Connector (L band, Local Oscillator) | |
DP-CRF-2501 | 5 kW High Power SPDT Switch | |
DP-CRF-2513 | 1 KW transmitter module | |
DP-CRF-4520 | 60 MHz OCXO Module, Custom | |
DP-CRF-4529 | 10 MHz, 10 ppb, 13 dBm OCXO Module | |
DP-CRF-5048 | 8 Way Power Combiner / Splitter Module for S Band | |
DP-CRF-5105 | LTCC Based X Band TR Module | |
DP-CRF-5111 | X Band 8W TR Module on Ceramic PCB Type 2 | |
DP-CRF-5117 | X Band 8W TR Module on Ceramic PCB Type 3 | |
DP-CRF-5120 | X band 300 Watt Transmitter Module (SSPA Based) | |
DP-CRF-5204 | IF1 Down Converter Module, 1620 MHz/1630 MHz, BMA Female Connector | |
DP-CRF-5207 | IF2 Down Converter Module, 180 MHz/70 MHz, BMA Female Connector | |
DP-CRF-5402 | Solid State Amplifier Module (X Band, Power Amplifier) | |
DP-CRF-5408 | 1:3 Power Divider module (BITE) | |
DP-CRF-5411 | Rugged Wide Band VHF/UHF RF Tuner (down converter) for WBSPU | |
DP-CRF-5414 | Single Channel Rugged HF Tuner (2 - 30 MHz) for WBSPU | |
DP-CRF-5420 | HF Tuner for Search Receiver | |
DP-CRF-5423 | Dual Quadrature Combiner Module 24 DP- | |
DP-CRF-5426 | Dual Quadrature Divider Module | |
DP-CRF-5429 | In Phase 4:1 Combiner Module | |
DP-CRF-5435 | 4 KW Power Amplifier Module | |
DP-CRF-5438 | 3.5 KW Power Amplifier Module | |
DP-CRF-5441 | 2.5 KW Power Amplifier Module | |
DP-CRF-5444 | 1.5 KW Power Amplifier Module | |
DP-CRF-5447 | 800W Power Amplifier Module, 1090MHz | |
DP-CRF-5450 | 4Way Hybrid Power Divider | |
DP-CRF-5453 | 8 Way Hybrid Power Divider | |
DP-CRF-5462 | DP-CRF-5462 1kW Power Amplifier Module | |
DP-CRF-5468 | High power Directional coupler - 9 GHz to 9.8 GHz - 300watts Peak & 60 watts Avg power | |
DP-CRF-5471 | U/VHF Wideband IF Filter Module | |
DP-CRF-5483 | 400MHz DDS synthesizer module | |
DP-CRF-5486 | L-Band 950-2050 MHz Transceiver Module | |
DP-CRF-5492 | X Band 100W Solid State Power Amplifier Module | |
DP-CRF-5510 | HF 2 to 30 MHz Signal Distribution Unit | |
DP-CRF-5519 | X Band Dual Quadrature power divider / combiner | |
DP-CRF-5522 | 2 KW Power Amplifier, 1030 MHz/ 1090 MHZ, Pin:44dBm | |
DP-CRF-5540 | 2.5kW SPDT Switch , 1030 MHz, IL:0.6dB(Max), Isolation: 25dB (Min) | |
DP-CRF-5546 | X Band 4 Way Quadrature Coupler Power Divider | |
DP-CRF-5549 | VHF/UHF Tranceiver module for CubeSat with Pc104 Interface | |
DP-CRF-5552 | S-Band Transmitter module for CubeSat with Pc104 Interface | |
DP-CRF-6002 | VHF Master Combiner Module | |
DP-CRF-6008 | Clock Synthesizer Module for Wind Profile Radar | |
DP-CRF-6014 | VHF Triple Channel, 20dB to 80dB Variable Gain Receiver Module for Wind Profile Radar | |
DP-CRF-6017 | 7 Way Power Combiner / Splitter Module VHF Band | |
DP-CRF-6020 | DP-CRF-6020 13-way Power combiner / splitter module for VHF band | |
DP-CRF-6023 | Microstrip based Hairpin type Band Pass Filter, 7.370GHz to 8.180GHz | |
DP-CRF-6026 | Microstrip patch array antenna for monopulse application, frequency 9.2GHz to 9.6GHz | |
DP-CRF-7004 | S-Band Dual Channel Analog Receiver | |
DP-CRF-7007 | LO and Dual Stage Up Converter Module | |
DP-CRF-7010 | RES and channel selector module | |
DP-CRF-7016 | Distributor Module | |
DP-CRF-7061 | Array Group Analog Receiver | |
DP-CRF-7073 | L-Band-TRM receiver | |
DP-CRF-7115 | VHF Receiver Module | |
DP-CRF-7118 | VHF 500 Watts Transmitter Module | |
DP-CRF-7127 | 20 MHz to 3000 MHz VHF/UHF Tuner | |
DP-CRF-7130 | C Band GaN Based 25Watts Quad Channel Transmitter | |
DP-CRF-7133 | C Band Quad Channel Receiver Board | |
DP-SSPA-5100 | X Band 100W Solid State Power Amplifier |
Based on order from the Navy, Data Patterns developed the complete Automated Test Equipment required for validating all the Line Replaceable Units (LRUs) utilized in the Seaking Helicopter. The upgrade was carried out at multiple Naval bases in India.
This engineering effort was fully validated and approved by the Quality Control Agencies for testing the flight critical LRUs and functioning of the LRUs on the aircraft.
Data Patterns is one of the few companies in the world who has carried out the implementation of a full aircraft LRU Test system.
Data Patterns designed and built the BrahMos Missile Checkout Equipment based on the requirements and support of DRDO and BrahMos. This unit validates the complete performance of the Missile through interfacing with it's umbilical and maintenance connections. The shelter mounted checkout equipment is utilized to test the articles on the field during it's life cycle, thus ensuring readiness for launch on demand. It comprises the power supplies, I/O interfaces, specific to type test equipment and VME based systems. This system has been designed for transportability and roadability as per the operational requirements.
The Digital Flight Control Computer is a Quadruple Redundant Flight Control Computer designed by DRDO and ADE and manufactured by Bharat Electronics Limited. Data Patterns has designed and manufactured the Automated Test Equipment required for the validation of this DFCC.
Segregated into an Analog Test System and Digital Test System, relevant boards can be plugged in on the front of the ATE and tested for full functional performance. Specialised adaptors enable probing of the backplane signals and also carry out measurements on the board by manual probing for debugging requirements.
The Power Module Checkout ATE is developed for testing DC-DC Power modules typically utilized in India's space program. The DC-DC converters are exhaustively tested for all design parameters including supply voltage range, line and load regulation, efficiency, ripple, noise, transient response and so on. Special power sources and loading mechanisms are deployed to enable testing of various types of power modules.
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20, 000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
The system features scalability from 128 lines to over 30000 lines portable large systems.
It is implemented using :
It is configured with :
It measures :
Satellite Sub systems tested are:
The Second Launch Pad Count Down system is implemented using VXI hardware designed by Data Patterns specific to the application requirements, featuring a redundant system handling upto 14000 I/O points.
The ATE monitors various aspects of the launch vehicle during this count down phase and assists in automating launch process. This product has been very reliable in operation since 2001. The ATE consists of precision analog input signal conditioners and digitizers and discrete as well as relay logic. One of the specialised modules used for fail/safe automation is an analog comparator which is programmable to carry out safety monitoring, independent of the software for fail/safe operation purposes. This world class system was implemented by Data Patterns against strong competition and proved it's reliability over many launches of the PSLV and GSLV from the Launch Pad.
Instrument Test Unit For Advanced Inertial Sensors (INTU) is used for testing and evaluation of Ring Laser Gyro (used in GSLV/PSLV launch vehicles), that detects the angular displacement during rotation. The INTU receives displacement signals from the sensor (RLG) to evaluate the sensor characteristics and also generates signals required towards initiating the action of the sensor.
This system contributes to the successful launch of many of India's rocket launch vehicles including the Polar and Geostationary Satellite Launches, the Chandrayan and the Mars Orbiter missions.
The INTU system consists of the following boards:
Redundant Strap down Inertial Navigation System (RESINS) checkout test station comprises of cPCI chassis with various functional I/O modules like ADC, DAC, DIO, VFC, Relay matrix, MIL 1553, GPIB, Serial communication interfaces and Custom Built System interface adaptor.
Software drivers for each functional block are developed in QNX, to perform functional checks of the integrated prime and redundant chains of the satellite launch vehicles Navigation system.
The following functional checks are performed for various On-board packages :
The custom built Signal Interface Adapter (SIA) is used to provide :
The Scan Mirror Test system is used for validating the linearity of the Scan Mirror Mechanism that is deployed on-board satellites. The system was a custom turnkey project in the electro optics domain.
Scan Mirror is swept linearly by a mechanical scanning gimbal and this allows the optical sensor to take large field exposures of the target using a single dimensional array sensor on-board the satellite. The linear mechanical movement is important for achieving an imaging linearity of the satellite, utilizing a complete non contact electro optic technique. The test system utilizes a thermovac compatible 22Mpixel camera and a pulsed laser source to monitor the movement of the scan mirror and thereby compute the movements linearity. Micro radiant level resolution is achieved through pixel level estimation algorithms.
The System is intended for acquisition of static strain data on large structures such as fuel tanks in launch vehicles and launch motor casings using a 24 bit Sigma Delta ADC and precision analog signals.
This product provides Micro strain level accuracy with extreme low drift and high temperature stability for a precision strain gauge measurement system engineered for large channel count applications.
Data Patterns has supplied thousands of strain gauge measurement channels for India's launch vehicle programs by using the cPCI architecture and providing compatibility with other data acquisition products.
This system can easily can accommodate displacement measurement transducers, temperature DAC and so on. Facilities for multi rack synchronization, time stamping, operation control, grapping and reporting tools simplify the operation of the system. A comprehensive built-in test enables validation of all wired sensors. This feature is very critical when large number of sensors are simultaneously being acquired.
Data Patterns has a strong RF and Microwave engineering capability, featuring a team of enthusiastic engineering talent, substantial investments in RF test and measuring instruments, and attitude to utilise the latest technologies.
An in-house manufacturing capability and an insatiable demand for fulfilling requirements of Radar, Electronic Warfare and Communication domains, Data Patterns has developed a whole line of building blocks including TR Modules, Up and Down Converters, Power Amplifiers, Transmitters, Combiners and Dividers for specific requirements. A list of products is given below.
DP-CRF-0500 | DDS Piggy Module, 250 to 660 MHz, BMA Female connector (Wideband, Custom) | |
DP-CRF-2303 | Local Oscillator 2 Module 1.44/1.56 GHz, BMA female Connector (L band, Local Oscillator) | |
DP-CRF-2309 | Local Oscillator 2 Module 1560MHz (L Band, Local OScillator) | |
DP-CRF-2312 | Local Oscillator 1 Module 7370 to 7970 MHz (C Band, Local Oscillator) | |
DP-CRF-2315 | Rugged, LO1 & LO2 Module for Primary surveillance Radar | |
DP-CRF-2501 | 5kW High Power SPDT Switch | |
DP-CRF-2504 | 4 KW Power Amplifier Front End Driver Module | |
DP-CRF-2507 | High power Microstrip Low pass Filter for 1KW Transponder Transmitter | |
DP-CRF-2510 | Front End Driver Board for Transponder Transmitter | |
DP-CRF-2513 | 1KW Transmitter with SPDT Switch for Transponder | |
DP-CRF-3407 | Monopulse Comparator - LLTR Ashwini Array - 3.1 to 3.5GHz | |
DP-CRF-3503 | Commercial, RF Adapter Module to test AGRU Tx Drive Distribution SRU | |
DP-CRF-3506 | Commercial, RF Adapter module to test DTRM Rx SRU | |
DP-CRF-4502 | OCXO Module 30MHz SMA Female connector | |
DP-CRF-4508 | C Band, X Band Micro Strip Filters | |
DP-CRF-4511 | C Band, X Band Micro strip Power divider and Coupler-50 Ohm | |
DP-CRF-4514 | 30Mhz to 500MHz Directional Coupler Forward power matching network module | |
DP-CRF-4517 | 30Mhz to 500MHz Directional Coupler Reverse power Matching network module | |
DP-CRF-4520 | 60MHz OCXO Module, Custom | |
DP-CRF-4523 | BITE Module, 9 GHz to 9.8 GHz | |
DP-CRF-4526 | Band Pass filter Test Board - 9 GHz to 9.8 GHz | |
DP-CRF-4529 | 10 MHz, 10 ppb, 13 dBm OCXO Module | |
DP-CRF-5000 | Calibration Power Divider 1:14, 3.1 to 3.5 GHz, QMA Female connector | |
DP-CRF-5003 | Transmit Divider 1:6, 3.1 to 3.5 GHz, QMA Female connector. | |
DP-CRF-5006 | Transmit Divider 1:4, 3.1 to 3.5 GHz, QMA Female connector. | |
DP-CRF-5009 | LO1 Divider 1:6, 2.5 to 2.9 GHz, QMA Female connector | |
DP-CRF-5012 | LO1 Divider 1:4, 2.5 to 2.9 GHz, QMA Female connector | |
DP-CRF-5015 | LO2 Divider 1:6, 540 Mhz, QMA Female connector | |
DP-CRF-5018 | LO2 Divider 1:4, 540 Mhz, QMA Female connector | |
DP-CRF-5021 | Master Clock Divider 1:6, 50 MHz, QMA Female connector | |
DP-CRF-5024 | Master Clock Divider 1:4, 50 MHz, QMA Female connector | |
DP-CRF-5027 | Calibration Switch - 1:2 - 3.1 to 3.5GHz - QMA Female connector | |
DP-CRF-5033 | Cascaded 6-17GHz Amplifier with 15GHz Low Pass Filter Integrated Module | |
DP-CRF-5036 | 6-26GHz Mixer with 6-17GHz LO Amplifier Integrated Module | |
DP-CRF-5039 | Radiating Segment - Antenna Panel (8x8) - 3.1 to 3.5GHz - BMA Female Connector | |
DP-CRF-5042 | Radiating Segment - Antenna Panel (6x8) - 3.1 to 3.5GHz - BMA Female Connector | |
DP-CRF-5048 | 8-Way Power Combiner - 3.1 to 3.5GHz - QMA Female connector | |
DP-CRF-5051 | 6-Way Power Combiner - 3.1 to 3.5GHz - QMA Female connector | |
DP-CRF-5054 | Radiating Segment - Antenna Panel (8x8) - 3.1 to 3.5GHz - BMA Female Connector along with QMA Termination for CAL LINES | |
DP-CRF-5057 | Radiating Segment - Antenna Panel (6x8) - 3.1 to 3.5GHz - BMA Female Connector along with QMA Termination for CAL LINES | |
DP-CRF-5060 | L-Band 70 MHZ to 950-1700MHz Up Conversion Module | |
DP-CRF-5063 | L-Band 950-1700MHz to 140 MHz Down Conversion Module | |
DP-CRF-5066 | L Band Clock Generation Up Down conversion Controller Module | |
DP-CRF-5102 | Transmitter Drive Module, 9GHz to 9.8GHz, BMA Female Connector | |
DP-CRF-5105 | LTCC Based X Band TR Module | |
DP-CRF-5108 | X Band TR Module Plank Controller Type 1 | |
DP-CRF-5111 | X Band 8W TR Module on Ceramic PCB Type 2 | |
DP-CRF-5114 | RF Test Board for X band TR Module | |
DP-CRF-5117 | X Band 8W TR Module on Ceramic PCB Type 3 | |
DP-CRF-5120 | X Band 100W Solid State Power Amplifier, Pin : 25 dBm | |
DP-CRF-5204 | IF1 Down Converter Module, 1620MHz/1630MHz, BMA Female Connector | |
DP-CRF-5207-600 | IF2 Down Converter Module, 180MHz/70MHz, BMA Female Connector | |
DP-CRF-5207-630 | Rugged, Single channel IF2 Down Converter Module, 70 MHz for Primary Surveillance Radar | |
DP-CRF-5210 | Radiating Element - 2x2 Antenna Panel | |
DP-CRF-5300-VER | Local Oscillator Module, 7.37 to 8.18 GHz BMA male connector (C Band, Local Oscillator) | |
DP-CRF-5303-VER | Calibration and Spurious/Image Frequency Rejection Module, 1620/1630MHz, BMA Male connector | |
DP-CRF-5306 | 1:3 LO1 Distribution Module 7.370GHz to 8.180GHz SMA Input and SMP output Connector | |
DP-CRF-5402 | Solid State Amplifier Module (X Band, Power Amplifier) | |
DP-CRF-5405 | Imaging and Monopulse Antenna Panel - 9 GHz to 9.8 GHz - 300W-SMA, TNC female connector | |
DP-CRF-5408 | 1:3 Power Divider Module - 9 GHz to 9.8 GHz - SMA female connector | |
DP-CRF-5411 | Rugged Wide Band VHF/UHF RF Tuner (down converter) for WBSPU | |
DP-CRF-5414 | Rugged three channel HF Tuner (2 -30MHz) | |
DP-CRF-5417 | S-Band 0.5W Amplifier Module | |
DP-CRF-5420 | Rugged HF RF Tuner (down converter) for Search Receiver | |
DP-CRF-5423 | Dual Quadrature Combiner Module for BPA | |
DP-CRF-5426 | Dual Quadrature Divider Module for BPA | |
DP-CRF-5429 | In Phase 4:1 Combiner Module for Power Amplifier | |
DP-CRF-5432 | In Phase 1:4 Divider Module for Power Amplifier | |
DP-CRF-5435 | 4 KW Power Amplifier Module | |
DP-CRF-5438 | 3.5 KW Power Amplifier Module | |
DP-CRF-5441 | 2.5 KW Power Amplifier Module | |
DP-CRF-5444 | 1.5 KW Power Amplifier Module | |
DP-CRF-5447 | 800W Power Amplifier Module, 1090MHz | |
DP-CRF-5450 | 4Way Hybrid Power Divider | |
DP-CRF-5453 | 8 Way Hybrid Power Divider | |
DP-CRF-5456 | 4Way Hybrid Power Combiner | |
DP-CRF-5462 | 1kW Power Amplifier Module | |
DP-CRF-5465 | 1:2 RF & IF Distribution Module with Status output for LLTR CU | |
DP-CRF-5468 | High power Directional coupler - 9 GHz to 9.8 GHz -300watts Peak & 60 watts Avg power | |
DP-CRF-5471 | U/VHF Wideband IF Filter Module | |
DP-CRF-5474 | Test board for 120W GaN Power Amplifier Module | |
DP-CRF-5483 | 400MHz DDS synthesizer module | |
DP-CRF-5486 | L-Band 950-2050 MHz Transceiver Module | |
DP-CRF-5489 | 18GHz Tuner Sub circuits | |
DP-CRF-5492 | X Band 100W Solid State Power Amplifier Module | |
DP-CRF-5495 | C Band & X Band Filters Test board | |
DP-CRF-5498 | X Band 4X100W Solid State Power Amplifier, Pin : 40dBm | |
DP-CRF-5501 | Receiver Front End Module, 9GHz to 9.8GHz, BMA Female Connector | |
DP-CRF-5504 | PLL Based HF to S Band Programmable Signal Source | |
DP-CRF-5507 | RF Front End For Down-Link Module (Mating connector option) | |
DP-CRF-5510 | HF 2 to 30MHz Signal Distribution Unit | |
DP-CRF-5513 | RF Front end module for UP-Link 1643.5 +/- 17Mhz, -106 dBm Rx Sensitivity, 73 dB Rx Gain, TNC connector | |
DP-CRF-5516 | Single channel X-band Receiver Front End Module, SMA Female connector | |
DP-CRF-5519 | X Band Dual Quadrature power divider / combiner | |
DP-CRF-5522 | 2kW Power Amplifier, 1030 MHz/ 1090 MHz, Pin:44dBm | |
DP-CRF-5525 | Driver Amplifier, 1030 MHz/ 1090 MHz, Pin:10 dBm, Pout:44dBm | |
DP-CRF-5528 | Pre Driver Amplifier, 1030 MHz/ 1090 MHz, Pin:10 dBm, Pout:27dBm | |
DP-CRF-5531 | 25W Power Amplifier, 1030 MHz/ 1090 MHz, Pin:23 dBm, Pout:44dBm | |
DP-CRF-5534 | 2 Way Hybrid Power Divider, 1030MHz/1090MHz, IL: 0.5dB (Max) | |
DP-CRF-5537 | 2 Way Hybrid Power Combiner, 1030MHz/1090MHz, IL: 0.6dB(Max) | |
DP-CRF-5540 | 2.5kW SPDT Switch , 1030MHz, IL:0.6dB(Max), Isolation: 25dB (Min) | |
DP-CRF-5543 | Dummy Transmission line Board for for 2kW IFF Power Amplifier | |
DP-CRF-5546 | X Band Quadrature Coupler Power Divider | |
DP-CRF-5549 | VHF/UHF Tranceiver module for CubeSat with PC104 Interface | |
DP-CRF-5552 | S-Band Transmitter module for CubeSat with PC104 Interface | |
DP-CRF-5558 | CIT Receiver Module | |
DP-CRF-5561 | 20-1000MHz VUHF Tuner - Down converter for Search Receiver, 76.8MHz IF, 40MHz BW | |
DP-CRF-5564 | 20 to 1000MHz VUHF Tuner - Synthesizer, Controller & BITE | |
DP-CRF-5567 | 1.5 to 30MHz HF Tuner | |
DP-CRF-5570 | 20 to 1000 MHz. Exciter- Synthesizer & Controller | |
DP-CRF-5573 | 20 to 3000MHz Exciter - Up Converter | |
DP-CRF-5576 | Antenna Switching Module for IFF Transponder , 1090MHz , Pin: 60dBm, IL:1.8dB(Max), Isolation:20dB (Min) | |
DP-CRF-5579 | Rugged, X Band (9.3-9.5 GHz) Digital Attenuator Module, SMA Female Connector for Primary Surveillance Radar | |
DP-CRF-5582 | 20 to 1000MHz VUHF Tuner - Front End | |
DP-CRF-5585 | 12.8GHz LO Generation & Controller Module for Ku Band Up Converter | |
DP-CRF-5615 | S-Band Transmitter | |
DP-CRF-6002 | VHF Master Combiner Module | |
DP-CRF-6005 | Digital calibration & IF2 Module of Imaging and Monopulse Radar | |
DP-CRF-6008 | Clock Synthesizer Module for Wind Profile Radar | |
DP-CRF-6011 | Single channel IF1 Down Converter Module, 1620/1630MHz, SMA Female connector | |
DP-CRF-6014 | VHF Triple Channel, 20dB to 80dB Variable Gain Receiver Module for Wind Profile Radar | |
DP-CRF-6017 | 7-way Power combiner / splitter module for VHF band | |
DP-CRF-6020 | 13-way Power combiner / splitter module for VHF band | |
DP-CRF-6026 | Microstrip patch array antenna for monopulse application, frequency 9.2GHz to 9.6GHz | |
DP-CRF-6029 | Down Converter Receiver Module | |
DP-CRF-6032 | VHF, 144 to 148MHz, Telemetry receiver module | |
DP-CRF-6035 | X4 Multiplier module (118.75-143.75 MHz to 475-575 MHz) | |
DP-CRF-6038 | X band 80W 4 Way Quadrature Coupler Power Divider and Combiner | |
DP-CRF-6041 | RF Filters LC BPF 26MHz 1dB BW 12MHz SMD | |
DP-CRF-6044 | RF Filters LC BPF 39MHz 1dB BW 18MHz SMD | |
DP-CRF-6047 | RF Filters LC BPF 59.5MHz 1dB BW 27MHz SMD | |
DP-CRF-6050 | RF Filters LC BPF 92MHz 1dB BW 42MHz SMD | |
DP-CRF-6053 | RF Filters LC BPF 144MHz 1dB BW 66MHz SMD | |
DP-CRF-6056 | RF Filters LC BPF 227.5MHz 1dB BW 105MHz SMD | |
DP-CRF-6059 | RF Filters LC BPF 358.5MHz 1dB BW 165MHz SMD | |
DP-CRF-6062 | RF Filters LC BPF 570.5MHz 1dB BW 263MHz SMD | |
DP-CRF-6065 | RF Filters LC BPF 850MHz 1dB BW 300MHz SMD | |
DP-CRF-7004 | S-Band Dual Channel Analog Receiver | |
DP-CRF-7007 | S Band Exciter Module for Ground based Applications | |
DP-CRF-7010 | RES and channel selector module | |
DP-CRF-7016 | Distributor Module | |
DP-CRF-7025 | Local oscillator module for 540MHz and 50MHz signal generation | |
DP-CRF-7034 | S-Band Up converter (2.7GHz-3.1GHz & 3.1GHz-3.5GHz) | |
DP-CRF-7043 | Radar Environmental Simulator | |
DP-CRF-7052 | Channel Selection Matrix Piggy Card | |
DP-CRF-7055 | RF distribution box | |
DP-CRF-7058 | Distribution Box | |
DP-CRF-7061 | Array Group Analog Receiver | |
DP-CRF-7061-630 | Eight channel Analog Receiver Module | |
DP-CRF-7064 | Tx Drive Distribution Network | |
DP-CRF-7067 | LO1 Distribution Network | |
DP-CRF-7070 | LO2 & Noise Distribution network | |
DP-CRF-7073 | L-Band-TRM receiver | |
DP-CRF-7076 | DRM - Receiver board | |
DP-CRF-7079 | GRF ATE | |
DP-CRF-7082-303 | 25W C band Quad Channel Transmitter | |
DP-CRF-7085 | C band 25W Transmitter Module | |
DP-CRF-7088 | C band Front End Receiver Module | |
DP-CRF-7091 | L Band 4 KW Transmitter Module | |
DP-CRF-7094 | L Band 2.5 KW Transmitter Module | |
DP-CRF-7097 | L Band 1.5 KW Transmitter Module | |
DP-CRF-7100 | 500W Transmitter Module with Diversity Switch, 1090MHz | |
DP-CRF-7103 | Frequency Synthesizer Module for Search Receiver | |
DP-CRF-7106 | 3.5KW Transmitter Module for CIT | |
DP-CRF-7109 | PLL Based LO2 Generation Module for Wide & Narrow Band RF Tuner | |
DP-CRF-7112 | 500 Watts VHF Transmitter Module | |
DP-CRF-7115 | VHF Receiver Module | |
DP-CRF-7118 | 500 Watts VHF Transmitter Module-205MHz CF 5MHz BW | |
DP-CRF-7121 | VHF Receiver and Power supply Module | |
DP-CRF-7124 | V/UHF synthesizer Module of Search Receiver | |
DP-CRF-7127 | 20 to 3000MHz V/UHF Tuner | |
DP-CRF-7130 | C Band GaN Based 25Watts Quad Channel Transmitter Board | |
DP-CRF-7133 | C Band Quad Channel Receiver Board | |
DP-CRF-7136 | S Band GaN Based 100Watts Dual Channel Transmitter Board | |
DP-CRF-7139 | S Band Dual Channel Receiver Board | |
DP-CRF-7142 | 2kW Transmitter Module, 1030 MHz/ 1090 MHz, Pin:10dBm | |
DP-CRF-8003 | 2KW IFF Pulsed Amplifier/Transmitter | |
DP-CRF-8006 | L-Band-TRM transmitter | |
DP-CRF-8009 | L-Band filter, 2W amplifier test board. | |
DP-CRF-8012 | Transmitter Module for Transponder | |
DP-CRF-8015 | L-Band IFF Receiver Module for TXP | |
DP-CRF-8018 | 4KW transistor module | |
DP-CRF-8021 | L-Band IFF Interrogator (Receiver Module) | |
DP-CRF-8024 | Power Combiner, 3.1 to 3.5Ghz, 4 : 1, BMA Female inputs connectors, QMA Female output connector | |
DP-CRF-8027 | 1KW L Band Transmitter Board for IFF using LDMOS Approach | |
DP-CRF-8030 | 1KW Transmitter Test board for LDMOS Approach | |
DP-CRF-8033 | 1 KW Power Amplifier Module | |
DP-CRF-8036 | 4 KW Power Amplifier Front End Module | |
DP-CRF-8039 | 4 KW Power Combiner Module | |
DP-CRF-8042 | 100Watts VHF Power Amplifier Module | |
DP-CRF-8045 | 300Watts VHF Power Amplifier Module Pallet | |
DP-CRF-8048 | VHF Power Amplifier Front End Controller Module | |
DP-CRF-8051 | 4W V/UHF Wideband Driver Amplifier Module for Power Amplifier | |
DP-CRF-8054 | Narrow Band VHF/UHF RF Tuner | |
DP-CRF-8057 | Narrow band VHF/UHF RF Tuner (down converter) with Single 10.7MHz IF output | |
DP-CRF-8060 | Front end module for U/VHF Narrow band tuner | |
DP-CRF-8063 | Synthesizer for Wide Band Tuner | |
DP-CRF-8066 | Synthesizer for Narrow Band Tuner | |
DP-ECM-0411 | Wide Band Dual Directional Coupler | |
DP-ECM-0600 | Wideband 1KW 45MHz Low pass filter Unit | |
DP-ECM-0603 | Wideband 1KW 67MHz Low pass filter Unit | |
DP-ECM-0606 | Wideband 1KW 103MHz Low pass filter Unit | |
DP-ECM-0609 | Wideband 1KW 165MHz Low pass filter Unit | |
DP-ECM-0612 | Wideband 1KW 285MHz Low pass filter Unit | |
DP-ECM-0615 | Wideband 1KW 512MHz Low pass filter Unit | |
DP-SSPA-5103-600 | 300W X Band Solid State Power Amplifier | |
DP-TRM-8006 | 500W VHF Transmitter/Receiver Module | |
DP-UDC-6701 | Airborne Ku Band Up Converter and L Band Down Converter |
Data Patterns has developed a line up of State of the Art Integrated solutions for spectrum monitoring, wideband searching, ECM & ESM, direction finding for Airborne and Ground Mobile Applications standard Products include VHF/UHF Search Receiver, HF Search Receiver, Monitoring Receiver & Jammers.
DP-ECM-0009-600 | Rugged HF Search Receiver (1.5 - 30 MHz) | |
DP-ECM-0003-600 | Rugged Wide Band Signal Processing Unit with HF Tuner (2 to 30MHz) | |
DP-ECM-0006-600 | Rugged Real Time Monitoring Receiver with HF Tuner (2 to 30MHz) | |
DP-ECM-0012-600 | Rugged 3 Channel HF Monitoring Receiver (1.5 - 30 MHz) | |
DP-ECM-0015-600 | Rugged HF Jammer Station (1.5 - 30 MHz) | |
DP-ECM-0405-600 | 30-500 MHz, 500W Filter Switching Unit For WIDEBAND POWER AMPLIFIER | |
DP-ECM-0408-600 | 30-500 MHz, 1000W WIDEBAND POWER AMPLIFIER | |
DP-ECM-0411-600 | Wide Band Dual Directional Coupler with 1KW Power | |
DP-ECM-0411-630 | Wide Band Dual Directional Coupler with 500W Power | |
DP-ECM-0600-600 | Wideband 1KW 45MHz Low pass filter Unit | |
DP-ECM-0603-600 | Wideband 1KW 67MHz Low pass filter Unit | |
DP-ECM-0606-600 | Wideband 1KW 103MHz Low pass filter Unit | |
DP-ECM-0609-600 | Wideband 1KW 165MHz Low pass filter Unit | |
DP-ECM-0612-600 | Wideband 1KW 285MHz Low pass filter Unit | |
DP-ECM-0615-600 | Wideband 1KW 512MHz Low pass filter Unit | |
DP-ECM-1005-600 | Rugged Wide Band Signal Processing Unit with V/UHF Tuner (30 to 3000MHz) | |
DP-ECM-1008-600 | Rugged Wide Band Signal Processing Unit with HVUHF Tuner (2 to 3000MHz) | |
DP-ECM-1011-600 | Rugged Real Time Monitoring Receiver with V/UHF Tuner (30 to 3000MHz) | |
DP-ECM-1014-600 | Rugged Real Time Monitoring Receiver- HVUHF (2 to 3000MHz) | |
DP-ECM-1017-660 | Advance Receiver Processing Unit -Conduction Cooled | |
DP-ECM-1029-600 | QDR LRU Chassis | |
DP-ECM-1032-600 | Rugged V/UHF Search Receiver (20 - 1000 Mhz) | |
DP-ECM-1035-600 | Rugged 3 Channel V/UHF Monitoring Receiver (20 - 1000 MHz) | |
DP-ECM-1038-600 | Rugged V/UHF Jammer Station (20 - 1000 MHz) |
Data Patterns offers a wide range of multi-function rugged LCD displays for rotary and fixed-wing aircraft. The current range extends from 3" to 20" units. All avionics displays offer leading edge functionality including on board smart processing and internal & external sensors support Video formats from RS170, Stanag 3350, PAL, VGA, DVI, ARINC 708, ARINC 818 standards are provided. The integration of the latest NVIS technologies and the optical stack-up allows for very high brightness, high contrast sunlight readable screens with minimized reflections, combined with low power consumption.
Display Technologies
NTSC/PAL RGBHV, DVI etc. to LCD compatible signals.
DP-DSP-8016 | 20" Marine Grade Display | |
DP-DSP-8022 | Smart Display Unit | |
DP-DSP-8040 | Foldable Display Unit | |
DP-DSP-8052 | 5 ATI Multifunction Display | |
DP-DSP-8061 | 6 x 8" Display System | |
DP-DSP-8070 | 4 ATI Multifunction Indicator | |
DP-DSP-8080 | 15" Cockpit Display | |
DP-DSP-8109 | 17" Inch Rugged Display System | |
DP-DSP-8115 | CDU for Signa 30 | |
DP-DSP-8121 | 3ATI Multifunction Indicator | |
DP-DSP-8130 | Advanced Display Unit | |
DP-DSP-8135 | Smart Standby Display Unit | |
DP-DSP-8142 | 6 x 4" Winch Operator Display |
data patterns has designed fire control systems for missiles and decoys for ground, air and naval applications.
.Data Patterns has designed prototyped, qualified and manufactured a wide variety of products intended for airborne applications in manned and unmanned aircraft. Ranging from smaller unmanned vehicles and missiles to manned fighter aircraft, Data Patterns has the largest number of qualified LRUs designed in India from a single source. Incorporating the latest techniques from thermal engineering and mechanical ruggedisation, Data Patterns' products are ideally designed for the application. A captive manufacturing facility enables production with reliability. At the same time, planning and preparing for obsolescence management and providing long term support for manufacturability is the key philosophy with respect to the avionic product lines.
DP-CIO-8143 | Communication and I/O Interface | |
DP-DMCS-8134 | Actuator Controller for UAV | |
DP-DSP-8040 | Foldable display | |
DP-DSP-8061 | 6 X 8" Display System | |
DP-DSP-8061 | 6 X 8" Display System | |
DP-DSP-8070 | 4 ATI Multifunction Indicator | |
DP-DSP-8135 | Smart Standby Display Unit | |
DP-IFF-8002 | IFF Transponder | |
DP-IFF-8005 | IFF Interrogator | |
DP-IFF-8008 | IFF Combined Interrogator Transponder | |
DP-MRET-8124 | Multi Redundant Embedded Timer | |
DP-OBC-0462 | Mission Computer Processor board | |
DP-OBC-1011 | OBC MK-IV | |
DP-OBC-8001 | Flight Control Computer for UAV | |
DP-OBC-8130 | OBC MK II | |
DP-OBC-8145 | Rustom Rugged Duplex Computer | |
DP-OBC-8151 | Airborne Protocol Converter | |
DP-PSU-6004 | ACU-IU | |
DP-PSU-7027 | PCD System (ACU & IU) | |
DP-RCU-8230 | Airborne Central Unit for Radar | |
DP-SIPU-8004 | Signal Processing IF Unit | |
DP-SPL-7435 | PCD-APSU | |
DP-SPL-8206 | Protocol Converter | |
DP-VPX-8144 | 3U VPX 5 Slot ATR Chassis |
Data Patterns has developed a High performance imaging and monopulse Radar for seeker applications. This is optimized for Land & Sea targets and has X-Band SAR (Synthetic Aperture Radar) based imaging capability. A range of Electro-Optical Seekers are under development.
A range of electro-optical products have been built for surveillance, imaging and testing requirements.
DP-ATE-8234 | IR Guided Missile Tester | |
DP-ATE-8237 | ||
DP-LOEP-8002 | Laser Receiver Unit | |
DP-SMTS-8002 | Scan Mirror Test System |
Small Satellites especially the Micro and Nano Satellite can significantly contribute towards the development of the country by accessing space at much lower cost and quick turnaround time.Data Patterns has designed and developed standard off-the-shelf products for Nano satellite bus suitable for Low Earth Orbit (LEO) satellite missions. These nano satellite platforms are ideal for scientic and educational payloads. The sub systems were designed in PC104 form factor and has standard interface for easy integration. Most of sub systems are proven in space, flown on NIUSAT, INS-1A, INS-1B & INS-1C satellites.
The Ground Station is a generalized open frame architecture designed by Data Patterns to support the space segment & relay mission data to the users.It has independent uplink and downlink communication channels for command and data functions. The generic design makes the control of parameters like frequency, modulation scheme, data rate and others simple. Common communication standards like HDLC, AX.25 and CCSDS are readily supported by the ground station system.The features and the flexibility of the design gives a complete and straight forward solution to communicate and control the satellites in orbit.
Ground Station System's |
Antennas VHF |
Power supplies of various ratings for Air, Naval ground based and space applications are developed. Products are implemented in VPX, VME, cPCI and custom form factor designs.
Most products qualified to requirements of MIL-STD-461C and MIL-STD-810D or the equivalent JSS 55555 are designed and manufactured. Airborne versions are designed to meet MIL-STD-704D. Specific design constraints are handled with respect to long time storage life and suitability for air cooled or conduction cooled applications. Designs suitable for high power supplies of various ratings for Air, Naval, Ground based and space applications are developed. Products are implemented in VPX, VME, cPCI and custom form factors designs.
DP-ATE-8033 | Shaker Table Power Supply | |
DP-ATE-8219 | ATS Power Module | |
DP-FCS-8110 | High Power PSU | |
DP-PSU- 7027 | PCD Power supply | |
DP-PSU-7006 | 5KW Power Supply | |
DP-PSU-7056 | Electrical Power System | |
DP-PSU-7086 | Adjustable Voltage Regulator Module | |
DP-PSU-8008 | Naval Power Supply System | |
DP-PSU-8056 | Display Power Supply | |
DP-PSU-8069 | DC-DC Converter | |
DP-PSU-8126 | 400W VME Power Supply | |
DP-PSU-8129 | 500W VPX Power Supply | |
DP-PSU-8132 | 200W_40VDC in_Pulsed Power Supply Module | |
DP-PSU-8138 | 1000W Power Supply | |
DP-PSU-8141 | 12V to 5V@15A & 3.3V@15A DC-DC Non Isolated Converter | |
DP-PSU-8144 | Airborne 3 phase 400Hz input Power supply | |
DP-SPL-6175 | Power Supply and Sequencer for X Band 100W SSPA | |
DP-SPL-6193 | Power Supply & Sequencer Module for X Band 300W SSPA Module | |
DP-SPL-PIA1001 | Naval 3 phase input Power Supply |
A number of Naval products have been designed, qualified and delivered to Naval Shipyards including Garden Reach Shipbuilders & Engineers Ltd (GRSE) and Mazagon Dock Limited (MDL)
Some systems have been supplied to M/s. Bharat Electronics Limited. Some Oceonographic systems have been supplied for scientific research purposes.
DP-BUOY-8003 | Data Buoy CPU | |
DP-DDU-8011 | Data Distribution Unit | |
DP-DLCP-8142 | Decoy Launch Control Panel | |
DP-DNIU-8000 | Data & Network Interface Unit | |
DP-NFCS-8153 | Operations Naval Console | |
DP-UWS-8001 | Autonomous Underwater Profiling Drifter |
Data Patterns has standard communication products for most military protocols such as MIL-STD-1553B, ARINC-429, ARINC-708, RS422. A spread spectrum modem is available for both terrestrial and satellite communication requirements.
These products are designed primarily for on-board interfaces in avionic systems and also for automatic test equipment requirements.
The Communication modem products are primarily employed in datalink applications
DP-CPCI-5499 | RF Modem | |
DP-COMM-8001 | DSSS Modem | |
DP-COMM-8005 | Radio Telemetry/Payload Receiver | |
DP-COMM-8008 | VHF Telecommand Transmitter | |
DP-PCI-7497 | PCI Express Fiber Optic Extender | |
DP-PMC-5778 | Dual Ethernet Adapter | |
DP-SPL-0163 | QPSK & BPSK Demodulator | |
DP-SPL-4222 | RS232 RS422 RS485 adapters | |
DP-XMC-5007 | MIL-STD-1553B and ARINC 429 | |
DP-XMC-5010 | Serial FPDP |
Data Patterns has developed the required expertise to design and maufacture BLDC Motor drivers used in close loop position control applications primarily for actuator control and Thrust vector nozzles and control surface (FINS) for missile and Torpedo applications. Multiaxis gimbals are developed for specific requirements.
These products are supported by test systems for electro Hydraulic and Electro mechanical actuator testing
DP-DMCS-8119 | Digital Electro Mechanical Actuator Controller | |
DP-DMCS-8125 | DSP based Electro Mechanical Actuator Controller | |
DP-DMCS-8128 | Torpedo Electro Mechanical Actuator Controller | |
DP-DMCS-8134 | Nirbhay UAV Actuator Controller | |
DP-DMCS-8137 | Torpedo 4 axis Actuator Controller | |
DP-DSC-8111 | 4 Channel Electro-Pneumatic Rear Servo Controller | |
DP-RDR-8032 | 2 Axis Platform Stabilised Seeker Gimbal |
Data Patterns utilizes Fibre Optic Communication for high speed data transfer requirements. Protocols such as Serial FPDP, Aurora, PCI Express, Gigabit Ethernet are implemented on Fibre Optic Medium.
Solutions using DWDM and EDFA components for high density fiber optic communications solutions are implemented
These products are implemented through modern high speed digitizers and digital to analog converters and are backed by FPGA based processing that implements baseband tuning and high speed I&Q vector generation algorithms. These find application in real-time signal processing, electronic waveform generation, digital tuners, and communication products.
DP-SPL-5653 | Waveform Generator card | |
DP-VME-5247 | VME64x Dual IF Signal Processor | |
DP-VME-5808 | IF Coded Waveform Generator Module | |
DP-VME-5826 | 6 Channel Digital Receiver Module | |
DP-VME-5838 | High Performance 335M, Six Channel Digital Receiver | |
DP-VME-5841 | VME based Quad Digital Controller Module | |
DP-VME-5844 | IF waveform generator module | |
DP-VPX-5843 | VPX based Octal Digital Receiver Board | |
DP-VPX-5846 | Dual Channel Narrow Band Digital Receiver with VPX Interface | |
DP-XMC-1101 | High speed digital pattern generator and data acquisition module | |
DP-XMC-1104 | 4-Channel, 200/250 MHz 16-bit ADC PMC / XMC Module |
Data Patterns has built system level consoles for number of programs.
Data Patterns undertakes design and manufacturing services for consoles as per system level requirements.
Data Patterns has designed and manufactured Fibre Optic Gyro based Inertial measurement units for under water applications with all algorithms including Kalmann filters and co-ordinate transformations implemented.
Data Patterns has standard software solutions for automation of test equipment application development (DP-CUTE) and for software development and debugging in multi processor environment (DP-CHRONO).
Specialized application software have been developed and implemented in mission critical aircraft displays, long endurance unattended data acquisition systems and various products for Radars, Electronic Warfare, Video Signal Processing and so on.
DP-FRA-805 | Portable Frequency Response Analyser | |
DP-IRG-5554 | GPS Time & Frequency Generator With Disciplined 15 Rubidium* Clock | |
DP-SYS-ATS | Actuator Test System | |
DP-SYS-DAQ | Data Acquisition System | |
DP-SYS-HIL | Hardware-In-loop Simulation System |