Resins #4819912

Unisect 11LV is a water white transparent polyurethane resin specifically created for use in the production of labels, and badges.

The resin system, when fully cured, exhibits excellent colour stability and mar resistance and adhesion to all the types of substrates normally used in the production of badges and labels.

RESIN SPECIFICATION:

Part A :

• Colour Water : White
• Specific Gravity at 250C : 1.04 ± 0.01
• Viscosity at 250C : 350 ± 30 mPa.s

Part B :

• Colour :  Water White
• Specific Gravity at 250C : 1.08 ± 0.01
• Viscosity at 250C : 200 ± 25 mPa.s
• NCO Value :  23.0 ± 0.2 %

Typical Cured Elastometer Properties

• Colour : Water White
• Specific Gravity at 250C : 1.09 ± 0.02
• Mix Ratio By Volume :  1:1 Part A : Part B
• Shore 0D Hardness :  50 ± 5
• Tensile Strength :  14.8 MPa
• Elongation at Break : 195 %
• Geltime 100 gm Mass at 250C : 10-12 mins
• UV Stability – QUV : No yellowing after 4000 hrs

QUV Weatherometer Test - 8 hrs UV exposure at 600C using lamps with peakemission at 340 nm. followed by 4hrs at 500C and 95% humidity in a continuous cycle.

All of the above tests were carried out on specimens cured at 250C for 7 days.

Although the elastomer is not fully cured for 7 days in practice the material can behandled without damage after 12-24 hours at 250oC.

 
PACKAGING: Unisect 11LV resin system is available in 25 litre and 200 litre drums and in 50 ml cartridges

RESIN STORAGE AND HANDLING:

• The resin system should be stored under clean dry conditions and out of direct sunlight at a temperature between 150C and 250C. At low temperatures the Part B of Unisect 11LV resin system may crystallise and should this happen customers are advised to contact Unisect Resources Ltd for advice.
• All skin and eye contact with Unisect 11LV resin system should be avoided and the resin system should be used in an area where adequate ventilation is provided and where there is no possible contact with foodstuffs.
• Before using Unisect 11LV resin system users should familiarise themselves with the Health and Safety Data Sheet for the product.
• To the best of Unisect Resources Ltd’s knowledge the information given in this Data Sheet is correct. However since use of the product is beyond the control of Unisect Resources Ltd users must determine for themselves the suitability of the product for their use and no responsibility is or will be accepted for problems or damage arising from the resin’s use. No guarantee is given or implied except other than the quality of the resin nor is freedom from patent restrictions to be inferred from these data

Unisect 1160 is a water white transparent polyurethane resin specifically created for use in the production of labels, and badges.

The resin system, when fully cured, exhibits excellent colour stability and mar resistance and adhesion to all the types of substrates normally used in the production of badges and labels.

RESIN SPECIFICATION:

Part A :

• Colour - Water White
• Specific Gravity at 250C - 1.04 ± 0.01
• Viscosity at 250C - 200 ± 20 mPa.s

Part B :

• Colour :  Water White
• Specific Gravity at 250C : 1.08 ± 0.01
• Viscosity at 250C :  200 ± 20 mPa.s
• NCO Value :  23.0 ± 0.2 %

Typical Cured Elastometer Properties

• Colour - Water White
• Specific Gravity at 250C - 1.06 ± 0.02
• Mix Ratio By Volume -  1:1 Part A : Part B
• Shore 0D Hardness -  90 ± 5
• Tensile Strength -  9.7 MPa
• Elongation at Break - 25 %
• Geltime 100 gm Mass at 250C - 10-12 mins
• UV Stability – QUV -  No yellowing after 4000 hrs

QUV Weatherometer Test - 8 hrs UV exposure at 600C using lamps with peakemission at 340 nm. followed by 4hrs at 500C and 95% humidity in a continuous cycle.

All of the above tests were carried out on specimens cured at 250C for 7 days.

Although the elastomer is not fully cured for 7 days in practice the material can behandled without damage after 12-24 hours at 250oC.

PACKAGING: Unisect 11LV resin system is available in 5 litre, 25 litre and 200 litre drums and in 50 ml cartridges

RESIN STORAGE AND HANDLING:

• The resin system should be stored under clean dry conditions and out of direct sunlight at a temperature between 150C and 250C. At low temperatures the Part B of Unisect 1160 resin system may crystallise and should this happen customers are advised to contact Unisect Resources Ltd for advice.

• All skin and eye contact with Unisect 1160 resin system should be avoided and the resin system should be used in an area where adequate ventilation is provided and where there is no possible contact with foodstuffs.
• Before using Unisect 1160 resin system users should familiarise themselves with the Health and Safety Data Sheet for the product.
• To the best of Unisect Resources Ltd’s knowledge the information given in this Data Sheet is correct. However since use of the product is beyond the control of Unisect Resources Ltd users must determine for themselves the suitability of the product for their use and no responsibility is or will be accepted for problems or damage arising from the resin’s use. No guarantee is given or implied except other than the quality of the resin nor is freedom from patent restrictions to be inferred from these data

With the assistance of our reliable transportation facilities, we have become capable of delivering the orders on time. We have hired only professional packaging personnel who have experience and expertise in this domain. They make use of the finest quality packing material to ensure zero damage during transit. Hydrocarbon Resin , Petcol 120 is a low molecular weight, pale yellow thermoplastic resin, produced from petroleum-derived monomers.

We promise to deliver the orders within the postulated time frame as we are backed by excellent logistics facility. We are supported by a well-structured warehouse that assists us wholly in keeping the lot safe and meeting urgent requirements at a time. Also, we keep it updated on regular basis.

Unisect 2120 is a water white transparent polyurethane resin specifically created for usein the production of labels, and badges.

The resin system, when fully cured, exhibits excellent colour stability and mar resistanceand adhesion to all the types of substrates normally used in the production of badgesand labels.

RESIN SPECIFICATION:

Part A :

• Colour - Water White
• Specific Gravity at 250C - 1.04 ± 0.02
• Viscosity at 250C - 140 ± 15 mPa.s

Part B :

• Colour Water - White
• Specific Gravity at 250C - 1.08 ± 0.02
• Viscosity at 250C - 200 ± 20 mPa.s
• NCO Value - 30.0 ± 0.2 %

Typical Cured Elastometer Properties

• Colour : Water White
• Specific Gravity at 250C : 1.06 ± 0.01
• Mix Ratio By Volume : 2:1 Part A : Part B
• Shore 0D Hardness  : 33 ± 3
• Tensile Strength : 5.5 MPa
• Elongation at Break : 130 %
• Geltime 100 gm Mass at 250C : 12-15 mins
• UV Stability – QUV** No yellowing after 4000 hrs

QUV Weatherometer Test - 8 hrs UV exposure at 600C using lamps with peak emission at 340 nm. followed by 4hrs at 500C and 95% humidity in a continuous cycle.

All of the above tests were carried out on specimens cured at 250C for 7 days.

Although the elastomer is not fully cured for 7 days in practice the material can behandled without damage after 12-24 hours at 250oC.

 
PACKAGING: Unisect 11LV resin system is available in 5 litre, 25 litre and 200 litre drums and in 50 ml cartridges

RESIN STORAGE AND HANDLING:

• The resin system should be stored under clean dry conditions and out of direct sunlight at a temperature between 150C and 250C. At low temperatures the Part B of Unisect 2120 resin system may crystallise and should this happen customers are advised to contact Unisect Resources Ltd for advice.

• All skin and eye contact with Unisect 2120 resin system should be avoided and the resin system should be used in an area where adequate ventilation is provided and where there is no possible contact with foodstuffs.
• Before using Unisect 2120 resin system users should familiarise themselves with the Health and Safety Data Sheet for the product.
• To the best of Unisect Resources Ltd’s knowledge the information given in this Data Sheet is correct. However since use of the product is beyond the control of Unisect Resources Ltd users must determine for themselves the suitability of the product for their use and no responsibility is or will be accepted for problems or damage arising from the resin’s use. No guarantee is given or implied except other than the quality of the resin nor is freedom from patent restrictions to be inferred from these data