Culture Instruments India LLP

Dabaspet, Bangalore, Karnataka

Application

The CI Bomb Calorimeter can be used to measure the heat generated from several applications. The calorific value of the following groups of materials can be measured :- Building Materials, Coal, Coke, Fuels (gasoline, kerosene, diesel and gas (turbine fuels), Hydrocarbon fuel, Food supplements, Crops, Waste and refuse combustible materials, etc., USAGE UP TO 40000 CALORIFIC VALUES.

Compliance : ASTM D240; D 4809; D5865; D1989; E711; ISO 1928; DIN 51900; BS 1016 ; IS 1350-2

Models

• 11007-00 BASIC - MICROPROCESSOR BASED WITH TEMP. LOGGING
• 11007-01 AUTOMATIC WITH SERIAL / PRINTER INTERFACE
• 11007-02 FULLY AUTOMATIC WITH TOUCH SCREEN, PC AND BALANCE INTERFACE

Bomb Calorimeter With Microprocessor Based Digital Thermometer- Cum - Firing Unit With Memorising Of Temperature ReadingAs per IP-12. For determining calorific values of liquid & solids. Supplied with one Stainless Steel Bomb, Crucible, Jacket calorimeter vessel, Motorised Stirrer, Pressure gauge with pipe fittings, Nichrome wire & other standard accessories.

Features

• 0.01 c resolution bright led display
• 10 readings memorising capability
• Fully integrated unit with stirrer, nichrome check, and firing.
• Can also be used to determine sulphur by bomb method.
• Displays both ambient and process temperature.
• Logging time interval can be set as per user requirements.
• Operation on 230v single phase, 50hz.

''TIC'' Gyratory type sieve shaker is driven by 1/2 HP Crompton Motor through a reduction gear. Suitable to carry 8'' dia upto 7 sieves.When clamped the sieve table inclines from the verical axis and the direction of the inclination changes progressively in the clock wise direction. The shaker also gives an up and down ward movement at a frequency of approx 270rpmIt has study cast iron body, The whole mechanism run in a closed greese filled cabin. Complete with adapter for 20Cm dia Sieves, 0-30/0-15 Minutes timer .But without sieves.Operation on 230V, 50Hz, Single phase AC Mains, with Crompton/Godrej Motor

Bridgeman Furnace is a Vertical Tripple Zone furnace, with 99% pure alumina tube. With 80-85mm ID tube and total length 700mm. Outer made of CR sheet Powder, coated. Temperature max. upto 1200C. Other Sizes as per requirement. SPECIFICATION: * Dual Heating Zone of 250mm each * Cold zone in center of 50mm. * 99% pure Alumina tube of 80-85dia ID x 700mm length. * Vertical Furnace, with both sides open. * Ceramic end caps to close the tube ends as and when required* Max. Working temp. 11500C * Temperature sensors of 'S' Type thermocouples. * Outer body made of CR sheet Powder coated * Heating by Silicone Carbide heaters of suitable capacity. with all necessary clamps and fittings. * The Vertical movement of the sample is driven by a High precision motor with fine screw rod train. * The movement will be vibration free across the entire operating range * The speed can be varied from 0.1mm/min. to 10mm/min. and stroke length from 1mm to full length. * Seperate control unit with 2 independant multi-step profile temperature controllers. * Movement control by an independent controller with continuos display of speed, stroke, run time and remaining time. * Provision to integrate the entire operation through a PC (Optional) * Operation on 440V, 3 Phase, 50Hz.only SAFETY FEATURES * It has safety features like:Home and end sensors for movement. * VAF meter to monitor voltage, current and frequency for heater life monitoring. * Automatic Heater cutoff on sensor failure * 1 Phase preventor. * Hot or cold run option.

A highly versatile instrument for 3rd party test labs, and R & D centres as it saves you precious lab space, maintenance, personal training, calibration costs and most of all automatic compliance to various national and international test standards and possibility to carry out special testings as per customer requirements.APPLICATIONS Automatic Film ApplicatorDrying Time RecorderCross Hatch TesterPencil Hardness TesterOver head heating system (Optional)Hotplate type heating system (Optional)Scratch Hardness Tester (Optional)Mar Tester (Optional)Linear Abrasion Tester (Optional)Wet Scrub Tester 2 Channel (Optional)Horizontal Tensile Tester (Optional) Horizontal Fatigue Tester (Optional)

Water bath incubator shaker: digital, stainless steel inner chamber. temperature range: above ambient 5ºc to 80ºc.  resolution: 0.1ºc.accuracy better than ±0.5ºc. digital  proportional control indication on 3 ½ digit led panel.operation on 230v ac mains.

The CI Acid Digestion Vessel (Bomb) helps in preparing analytical samples for analysis by combining various chemicals. Inner Made of Teflon and outer made of Stainless steel with Brass plated lid. APPLICATIONS It is used in various industries like pharma, Pollution control boards, testing Labs, Research institutes, Universities. etc. for digestion of Organic or Inorganic samples. * Accelerated Digestion, as compared to open system at atmospheric pressure. * Dissolves samples without losing original trace elements * No unwanted Contaminations. * Inner made of high density Teflon. * Permits the use of strong acids, which will attack most other conventional containers. MODELS AD23 AD50 AD100 AD150 AD200 SIZE 23ml 50ml 100ml 150ml 200mlSAMPLE VOLUME15ml 30ml 60ml 100ml 150mlMAXIMUM TEMP. 200C

MODEL : EMSS-200DRY sieving : StandardMode of operation : Continuous and intermittentSieve Capacity : Upto 8 full size sieves of 50mm height (Total load with sieves 6 kgs)Timer : Programmable from 1 min to 99min SAILENT FEATURES Complete stainless steel bodyideal for particle size analysis and separationtri-directional shifting motionintermittent and continuous shifting motion with 15 programmable levels of amplitudevery low noise operationprogrammable shake time from 1min to 99mincapacity upto 8 sieves of 200mm dia x 50mm heightUSB interfacesuitable for dry and wet sieving

Our Ovens have been designed for high performance drying, thermal process with fresh air supply, short process application, heat-up time and with precise heat control. Compliance as per ASTM , ISO, ISSTANDARD FEATURES Chamber Design : Double / Triple Walled Inner Chamber : Made of thick Gauge, Stainless Steel 304. Finish : Matt finish. Outer Body : CR/Mildsteel sheet. Powder coated finish or S.S. Matt finish Controller : Microprocessor based Digital PID controller with both process and set value display. Sensor Type : RTD sensor. Trays : Adjustable Rod mesh or Perforated Trays. Air Circulation : Conventional Air flow by dynamically balanced SS blower with Heavy, continuous Duty TEFC motor. Insulation : Low K factor Thick Ceramic Wool/Glass wool Insulation Heaters : Special SS air heaters. Gasket : Silicone Gasket. Temp. Range : 50C to 200C : 50C to 250C : 50C to 300C : 50C to 400C Resolution : 0.1 / 1C Accuracy : 1C @ 100C Operation : 230V 50Hz, single phase. MODELS : A) Economy B) Standard C) Laminar (ISO oven) D) Geared E) Industrial F) Thin Film Oven OPTIONAL ACCESSORIES & FEATURES : 1) Toughned Glass ViewWindow 2) Digital Timer 3) High Set point cutoff 4) Door to blower & heater Interlock 5) Temperature logger with pc interface 6) Profiling control 7) Cooling Coil 8) Air Curtain (For Industrial Ovens) 9) Spare Trays (Rod mesh/Perforated) 10) Variable Air Flow Rate 11) Touch screen PLC based control with inbuilt data and event logging for totally integrated test process 12)Motorised Turn table for sample rotation (RPM & Load capacity as per requirement) 13)Door Locking Arrangement 14) Castors for easy movement 15) 110V single phase/440V Three phase

CI vacuum oven microprocessor based digital control of temp. cylinderical model

 

Chamber made of double walled, inner chamber of ss 304 grade, and outer of mild steel, finished elegantly powder coated. insulationbetween inner and outer chamber is filled with high gradeglasswool with a gap of 75mm thickness. band type air heatersare made of high grade kanthal wire of suitable wattage, wounded on the chamber.

 

Silicon rubber gaskets with effective door locking system for sealing to hold vacuum. the door has viewing toughened glass window with leak proof sealing. full size control panel is on top.

 

Consisting of microprocessor temp. controller with set and ‘process’ value display on panel. dial type vacuum gauge, inlet/outlet regulator, max. vacuum 670 mm of hg.

 

Supplied with 2 nos.s.s. perforated trays, but without vacuum pump.

Special features

• In-built high-set cutoff (optional)
• Saves upto 30% electricity
• Temperature gradiance throughout  the inner chamber is within 5oc
• Auto cutoff of blower and heater on door opening

 

Some standard sizes

Inner chamber size w x d x h

• 2’ x 2 x 2’
• 2’ x 2’ x 3’
• 3’ x 3’ x 3’
• 4’ x 3’ x 3’
• 4’ x 4’ x 4’
• 5’ x 4’ x 4’

Other custom built sizes on request.

Application

Useful as a preliminary screening test for solid substances. In view of the complex nature of the ignition and combustion of solids, the self-ignition temperature determined according to this test method should be used for comparison purposes only.

 

Compliance :

• European Commission Directive 92/69/EEC, method A16:
• NF T 20-036 (September 85). Chemical products for industrial use. Determination of the relative temperature of the spontaneous flamability of solids

APPLICATIONUsed to determine whether a powder or dust will explode when exposed to an ignition source when in the form of a dust cloud. It is a preliminary test, to be followed with more intensive testing. The system is Automatic in nature with automatic dispersion of sample and initiation of spark and display of st-0, st-1 or st-2STANDARDACCESSORIES/PARTS 25014-00 1.2Litre Glass Test Vessel 01 No. 25014-01 Safety Enclosure 01 No. 25014-02 Top Lid assembly with flap and sensor 01 Set. 25014-03 Sparking Power Supply 01 No. 25014-04 Sparking Electrodes 02 No. 25014-05 Electrode connecting leads 02 No. 25014-06 Electrode Holder 02 No. 25014-07 Electrode Holder O 04 No. 25014-08 Air release system with atomiser and sample holder 01 Set OPTIONAL ACCESSORIES/SPARES 25014-09 Glowing coil 02 No. 25014-10 Glowing coil holder 01 No. 25014-11 Glowing coil Power Supply 01 No 25014-12 Spare flap 01 No. 25014-13 Spare position sensor 01 No. 25014-14 Spare Pressure sensor 01 No. 25014-15 Spare Solonoid Valve 01 No. 12010-00 Vacuum Oven 01 No. 09127- Test sieve 01 No. Digital Moisture Balance 01 No.PRE-INSTALLATION ON-SITE REQUISITES A Fume Hood with regulated air draft Power : 15A, 3 pin power supply Clean dry and regulated air supply Min. 8 Bar.

STANDARDS CONFIRMED TO: IS: 1060 P-3, ISO535, DIN53132 TAPPIT441, En20535, BS EN 20535 PAPTAC, F.2 TECHNICALSPECIFICATIONS: Specimen Size: 100mm Dia. X 75mm Cylinder Size : 100mm dia. Roller Weight : 10 Kgs. Roller Size : 100mm dia. X 200mm CI Cobb Tester is a sturdy and precise instrument with non-corrosive all aluminium powder coated body. The instrument is provided with a marker to indicate the exact level of water required, also ensuring uniformity of water level over the samples. A gasketed clamping arrangement for the sample on the underside of the cylinder. Tilting provision has been provided for easy draining of water after test, the cylinder 0 gets locked on turning by180 and the knob can be used as a handle. Also Available is a semi-automatic version with programmable timer and automatic tilting mechanism. A motorised roller arrangement can also be provided as an optional accessory. OPERATION: Loosen the bottom bolt according to the PLY/GSM of the board. Place the board between the bottom plate and the cup, tighten the screw so that there is no leakage. Fill the water up to the groove For 1 Min. (or refer standards you follow). Loosen the plate and remove the board carefully, place it on a flat surface. using the roller press the board and then weigh. Note down the weight of the board before and after the procedure. STANDARD ACCESSORIES A. SAMPLE CUTTING TEMPLATEB. 10Kg. ROLLER WEIGHT OPTIONAL ACCESSORIES: A. DIGITAL BALANCE B. SPARE BLOTTING PAPERC. SAMPLE CUTTERD. TIMER WITH BUZZER