Our Product / Services
Hydraulic Pumps
2 Products availableHand Pumps
2 Products availableFuel Injection Parts
1 Products availableLeading Manufacturer, Supplier & Retailer of STAINLESS STEEL CENTRIFUGAL PUMP CFS SERIES, high pressure plunger pump, rotary lobe pumps, Vertical Axial Flow Pump and MMP CENTRIFUGAL PUMPS.
we supply a wide array of dairy and pharmaceutical pumps, which are made from high quality rolled stainless steel. Our range of dairy and pharmaceutical pumps feature unique designs, trouble free safe and smooth operation. We also customize these pumps as per the specific requirements of clients.
milk, cream, butter milk condensed milk
fruit 3uice, beer, wine, sugar syrup
vitamin solutions, sugar & confectionery.
r 0 water, dm water, pure water. Water for injection (wfi)
vegetable oil, mineral oil, lub oil etc.
pharmaceutical formulations, syrup etc.
alkaline solution / alcoholic drinks.
acids, fine chemicals
bottling plants, soft drinks & distillery
food processing / liquid food stuffs
colour dyes and pigments / paints
descaling applications, paper & cement industries
water treatment plants
as all pumps are made from rolled stainless steel, mechanical properties are far superior then cast material.
pore free, non-pitting and non-adhering smoother surface, so less friction losses, and less service corrosion.
super finish surface also ensure no ingress or emission of germs or impurities during pumping or idling which is basic requirement of sterile hygienic application.
designed for cip (clean in place) or manual cleaning
pumps are highly energy efficient and requires less npsh to function without cavitations
pump can handle liquids having viscosities up to 1500 centipoises
the pumps can work under a vacuum of 720 mm of hg, suitable for vacuum evaporators.
the best elastomers are used in the pumps to provide optimum resistance for high temperatures and chemicals.
pumps are available with open/semi open impellers.
minimum working / rotating parts
safe and quite operation levels.
gentle product handling with lower maintenance and down line cost.
dynamically combinations of seal faces as per customers requirement (single seal / double seal, seal external cooling)
suitable for standard motor or flange type or foot cum flange type motor or engine.
monobloc or bare pumps or with trolley.
also with flame proof motors .
various types of connection like triclove joints sms, flanges or threaded nipple/coupling.
pumps with adjustable legs, available on request.
superior quality
value for money
trouble free performance
product customization
rapid delivery of both custom & standard pumps
higher efficiency
innovative design
responsibility of product/performance / service
casing :- aisi 316 / 316l / 304l / 304
impeller :- aisi 316 / 316l / 304l / 304
wear plate :- aisi 316 / 316l / 304l / 304
shaft :- aisi 316 / 316l / 304l / 304
seal :- tc/tc , sic/sic , ss/carbon or even seal in special application
motor cover :- ss-304 / s 202
gasket :- viton / nitrile / silicon / ptfe
detergent, soaps, paste & shampoo
textile sizing, dyeing & finishing systems
natural cellulose fiber / synthetic fiber system
hot & cold water pumping.
Malhar High-Pressure (simplex / duplex / triplex / sixplex ) plunger pump is a positive displacement pump. Which can able to deliver high flow stream at high pressure with high efficiency and These pumps are also know as hydro test pump, pressure test pump, hydrostatic test pump.
Air port & Ship Yards.
Railway Workshop & Cleaning Yards. State Transport & Workshop.
Industrial & Agriculture Purpose.
Auto Two & Four Wheel Workshop for washing /cleaning application.
RO water and sea water high pressure application.
Pumps are meant for high Mechanical Effiency means less energy Consumption, Lower Cost Smaller Motors, Lower Drive Costs. Easy-clean pump head which is ideal for in place cleaning, or can be rapidly stripped for manual cleaning, without disconnecting the pipe work. Positive, Uninterrupted Displacement by specially designed rotors creates a steady, gentle pumping action which does not shear, agitate or aerate the product. Pumping chambers without pockets or crevices to harbor bacteria or contaminants. No Contact between moving parts and no internal bearings in pump head. Solid stainless steel, ASI 316 quality, pumps head, rotors and shafts. Food quality rubber covered and plastic rotors are also available. Robust, Cast Iron gear case enclosing oil Lubricated rolling bearings are precision timing gears. Generous distance separating the pump head from the gear case. End Connection Port Flanged Threaded Customized.
three- or four-vane axial flow propeller is hydraulically balanced via pressure equalizing balance holes and a top propeller hub wear ring to reduced axial down thrust.
outer flanged columns are bolted together with through bolts for ease in assembly. Alignment is maintained via centering fits on all parts
flared suction bell provides a smooth waterway entrance to the impeller and has integral splitters to reduce inlet swirl and entrance losses
stator case with integral diffuser vanes may be either a single-piece casting or a fabrication.
discharge elbow may be located above or below ground and at any outlet orientation.
seal chamber accepts packing or mechanical seal to suit service requirements.
flows to 181700 m3/h (800 000 gpm)
heads to 11 m (35 ft)
speeds to 1770 rpm
sizes 200 mm (8 in) to 3.1 m (123 in)
settings to 8 m (25 ft)
the vaf is a vertical high efficiency, axial flow impeller pump together. We have a complete range of this type of pumps which are suited for applications that require large quantities of flow with low head.
multi-stage vertical centrifugal pump, diffuser type bowl.
axial flow impeller, high efficiency.
can handle solids up to 14 diameter (365 mm).
counter clockwise rotation viewed from shaft coupling.
api 610 latest edition construction available (vs3 type on special request only)
above or below base discharge.
discharge elbows designed to reduce friction losses, diffusers designed to minimize turbulence and increase efficiency.
product, oil or fresh water lubrication.
rotor pull-out design available.
bowls: cast iron with bronze impeller.
column: carbon steel with aisi-1045 shaft.
discharge head: fabricated steel.
basket type strainer.
extended suction bell (umbrella) to minimize vortices.
flood control,
water treatment,
shipping,
ground water development and irrigation,
cooling water (power),
dewatering and water supply (mining),
agriculture
mining,
water resources,
power generation,
general industries
Can withstand wide voltage fluctuation from 300-440 volts. Suction lift up to 7.5 meters. Top flat efficiency curve : minimum variation in efficiency in entire operating rangeEfficiency at par with internationally available pumps higher up to 10 points than minimum required by Indian standards specification Models are with IP 44 protection. Models with IP 55 protection are also available on requestClass of insulation B ( F Class for 9.3 kw and 11.0 Kw ratings). Designed to prevent overloading and motor burning Dynamically balanced rotating parts ensure minimum vibrations Replaceable wearing parts and hence longer life Designed for automatic air release during primingContinuous rated motor Inside and outside of pump covered by anticorrosive paint.
Irrigation.Industries for clear water handlingWater supply for domestic use in apartments, Buildings and hotels.MMP Series Three Phase Pumps : Single stage, High speed horizontal, Centrifugal , Monobloc with volute type delivery casing
Impeller : Cast iron Delivery casing : Cast iron Motor body : Cast iron Shaft : EN -8 Shaft Sleeve : SS-410
Head : Up to 90 meters Capacity : 19.0-2.0 liters per second Power rating : Up to 30 hp
Impeller : Bronze / Stainless Steel Shaft : Stainless steel Shaft Sleeve : Chrome Steel
Approximate performance of MMP Series, 2 pole, Monobloc pumps, rated voltage, 50 Hz , Three phase A.C. power supply
PUMP MODEL | POWER RATING | PIPE SIZE ( mm ) | TOTAL HEAD IN METER | |||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
6 | 8 | 10 | 12 | 14 | 16 | 18 | 20 | 22 | 24 | 26 | 28 | 30 | 32 | 34 | 36 | |||||
KW | HP | SUC | DEL. | CAPACITY IN LITERES PER SECOND | ||||||||||||||||
MMP-0515 | 0.37 | 0.5 | 25 | 25 | 2.0 | 1.9 | 1.8 | 1.0 | 0.2 | |||||||||||
MMP-130 | 0.75 | 1.0 | 25 | 25 | 2.7 | 2.3 | 2.1 | 1.8 | 1.3 | 0.9 | 0.7 | 0.4 | 0.0 | |||||||
MMP-115 | 0.75 | 1.0 | 40 | 40 | 5.4 | 4.7 | 3.8 | 1.7 | 1.5 | |||||||||||
MMP-224 | 1.5 | 2.0 | 50 | 50 | 5.8 | 5.3 | 5.0 | 4.7 | 3.5 | 3.0 | 2.5 | 2.0 | 1.2 | |||||||
MMP-325 | 2.2 | 3.0 | 65 | 50 | 9.2 | 8.8 | 8.4 | 7.9 | 7.4 | 7.0 | 6.4 | 5.8 | 4.9 | |||||||
MMP-335 | 2.2 | 3.0 | 50 | 40 | 5.0 | 4.9 | 4.8 | 4.7 | 4.6 | 4.4 | 4.2 | 4.0 | 3.8 | 3.6 | 3.2 | 2.7 | 2.0 | |||
MMP-515 | 3.7 | 5.0 | 100 | 100 | 32.8 | 31 | 28.0 | 24.2 | 19.0 | 12.8 | ||||||||||
MMP-520 | 3.7 | 5.0 | 80 | 80 | 23.5 | 22.8 | 21.9 | 20.8 | 19.4 | 17.7 | 15.9 | 13.9 | 10.8 | |||||||
MMP-527 | 3.7 | 5.0 | 80 | 65 | 14.2 | 13.4 | 12.6 | 11.6 | 10.3 | 8.7 | 5.8 | |||||||||
MMP-538 | 3.7 | 5.0 | 65 | 50 | 8.5 | 8.4 | 8.3 | 8.1 | 7.8 | 7.6 | 7.1 | 6.5 | 5.8 | |||||||
MMP-822 | 5.5 | 7.5 | 100 | 100 | 27.1 | 25.5 | 23.9 | 22.0 | 20.0 | 17.5 | 14.2 | |||||||||
MMP-830 | 5.5 | 7.5 | 80 | 65 | 19.0 | 18.2 | 17.3 | 16.4 | 15.4 | 14.2 | 13.0 | 11.1 | ||||||||
MMP-837 | 5.5 | 7.5 | 65 | 65 | 12.6 | 12.4 | 12.1 | 11.8 | 11.3 | 10.0 | 9.2 | |||||||||
MMP-1030 | 7.5 | 10.0 | 100 | 100 | 31.9 | 30.7 | 29.4 | 28 | 26.5 | 25 | 23.3 | 21.2 | 17.5 | |||||||
MMP-1331 | 9.3 | 12.5 | 100 | 100 | 33.3 | 32 | 30 | 28.5 | 26 | 23.3 | 19.5 | 13 | ||||||||
MMP-1537 | 11 | 15.0 | 100 | 100 | 36.7 | 35.8 | 34.1 | 33.3 | 32 | 30 | 27.6 | 25 | 20 | 17.5 | ||||||
PUMP MODEL | POWER RATING | PIPE SIZE ( mm ) | TOTAL HEAD IN METER | |||||||||||||||||
28 | 32 | 36 | 40 | 44 | 48 | 52 | 55 | 60 | 64 | 68 | 72 | 76 | 80 | 90 | 94 | |||||
KW | HP | SUC. | DEL | CAPACITY IN LITERES PER SECOND | ||||||||||||||||
MMP-550 | 3.7 | 5.0 | 50 | 40 | 4.1 | 3.9 | 3.7 | 2.7 | 2.0 | |||||||||||
MMP-852 | 5.5 | 7.5 | 65 | 50 | 8.6 | 8.1 | 7.5 | 6.8 | 5.9 | 4.5 | 3.5 | |||||||||
MMP-1040 | 7.5 | 10.0 | 80 | 65 | 17.8 | 15.9 | 13.3 | 9.5 | 18 M HEAD AT 20 LPS | |||||||||||
MMP-1065 | 7.5 | 10.0 | 65 | 50 | 7.5 | 7.1 | 6.8 | 6.4 | 6.0 | 5.3 | 4.3 | 3.0 | ||||||||
MMP-1348 | 9.3 | 12.5 | 80 | 65 | 17.9 | 17.0 | 16.0 | 14.8 | 11.6 | 20 M HEAD AT 19 LPS | ||||||||||
MMP-1372 | 9.3 | 12.5 | 65 | 50 | 8.0 | 7.9 | 7.8 | 7.6 | 7.2 | 6.2 | 5.6 | 3.0 | ||||||||
MMP-1555 | 11.0 | 15.0 | 80 | 65 | 19.2 | 18.3 | 17.3 | 15.8 | 14.6 | 11.0 | 9.7 | |||||||||
MMP-1575 | 11.0 | 15.0 | 65 | 50 | 8.3 | 8.0 | 7.8 | 7.4 | 7.0 | 6.5 | 5.8 | 4.5 |
manual hydro test pumps are portable type and can be easily handled by one man. The pump unit mounted on fabricated m.s. Pail, which stores liquid for testing, as well as provide self base for testing. In this type of separate foundation is not required. Manual hydro test pumps are available with ci ms gm ss body, ms fabricated pail having water filling capacity 9 , 12 or 22 liters , ss piston , ci ms handle ss check valve, brass pressure release cock , 4 dial pressure gauge and 1.5 meters pressure hose with end connections .
manual hydro test pumps are portable type and can be easily handled by one man. The pump unit mounted on fabricated m.s. Pail, which stores liquid for testing, as well as provide self base for testing. In this type of separate foundation is not required.
manual hydro test pumps are available with ci / ms / gm / ss body, ms fabricated pail having water filling capacity 9 , 12 or 22 liters , ss piston , ci /ms handle ss check valve, brass pressure release cock , 4 dial pressure gauge and 1.5 meters pressure hose with end connections .
boilerspressure vesselsc.i. Mainscastingsgas cylindersparts subjected to hydraulic pressure standard accessoriesm.s. Fabricted pail
brass foot valveg.m.j.s.s check valvebrass pressure release cockpressure hose with attachmentspressure gaugefor testing up to 705 kg/cm2 (10, 000 ps.i.)
ht-5 for 500 lbs (35 kg/cm2) testing:- having m.s body c.i. Handle and fulcrum with standard fitting , pail size 12 liters. ht-10 for 1000 lbs (70 kg/cm2) testing: having m.s. Body, c.i. Handle and fulcrum with standard fittings , fabricated m.s. Pail size 22 liters. ht-15 for 1500 lbs (105 kg/cm2) testing: having m.s. Body stainless steel piston with g.m. Head , heavy duty c.i. Handle and fulcrum , with standard fittings, mounted on m.s. Fabricated pail size 22 ltrs. ht-20 for 2000 lbs (140 kg/cm2) testing:- having m.s. Body , stainless steel piston with g.m. Head , heavy duty c.i. Handle and fulcrum , with standard fittings , mounted on m.s. Fabricated pail size 22 ltrs.
ht-30 for 3000 lbs (211 kg/cm2) testing :- having m.s. Body , stainless steel piston with g.m. Head , heavy duty m.s. Handle with fulcrum , with standard fittings mounted on m.s. Fabricated pail size 22 ltrs. ht-50 for 5000 lbs (352 kg/cm2) testing:- having s.s. Body , stainless steel piston with g.m. Head , heavy duty m.s. Handle with fulcrum with standard fitting mounted on m.s. Fabricated pail size 22 ltrs. ht-70 for 7100 lbs (500 kg/cm2) testing :- having s.s. Body, stainless steel piston with g.m. Head, heavy duty m.s. Handle and c.i. Fulcrum with standard fitting mounted on m.s. Fabricated pail size 22 ltrs.
irrigation sprinkler installations pressure boosting multistage story building hydro pneumatic water works fire fighting mining wash down applicationshydraulic press / circuits transfer & circulation hot & cold water boiler feed pumps condensate pumps
capacities :- 2500 lpm maximum heads :- 400 mtrs maximum sizes :- 1 to 6 temperature :- 140 c maximum
vertically split suction. Intermediate and discharge casings clamped together by external tie bolt and sealed with gaskets or o ring as required by the design, pumping temperature of the liquid pumped and the construction of the pumpgrease lubricated anti friction bearings designed to meet the requirements mounted on either sidepump uses soft graphite lubricated asbestos. The shaft is fitted with renewable shaft sleeve in the region of the stuffing box, which protects the shaft from wear due to packing. Special water-jacketed stuffing boxes, and special design of stuffing boxes with mechanical seals are availablethe discharge nozzle is top vertical. Suction nozzle horizontal located on the right hand side, left hand side or central position when viewed from the driving end is available. The flanges are round corresponding to international standardsthe direction of rotation is clockwise as viewed from the driving end.
suction/delivery casings & stage casings closed grain cast iron. Impellers. Diffusers, sleeves closed grain cast ironshaft and keys stainless steel 410 clamping studs en-8special material available on request bronze. Carbon steel, s.s., alloy steelpumps are backed by prompt and efficient after sale service, high degree of precision in manufacturing ensuring interchangeability of components as spares.reserves the right to change the specifications and data due to continuous improvement in design.
SR NO | PRODUCTION | SIZE | RANGE | APPLICATION |
1 | CHP PUMPS | 1” TO 4” | 25 LPM TO 1000 LPM UP TO 250-300 MLC | BOILER FEED PUMPS |
2 | CHH PUMPS | 1” TO 4” | 25 LPM TO 1000 LPM UP TO 400 MLC | WATER INJECTION PUMPS , COOLING WATER INJECTION PUMPS |
3 | CM PUMPS | 3” TO 6” | 300 LPM TO 2500LPM UP TO 200 MLC | DEWATERING PUMPS |
4 | CMS PUMPS | 3” TO 6” | 400 LPM TO 2500 LPM UP TO 80 MLC | COOLING TOWER , TRANSFER OF CORROSIVE CHEMICAL AND AS PROCESS PUMPS IN INDUSTRIES |
High Head and High Capacity Hand Pump Suitable for:-
vDrum and Tanker Loading / Unloading
vHigh-Head and In Plant Transfer
vTrash / Irrigation / Diesel / Acid / Mud / Pump
vUnderground tank Emptying
vSump Emptying
vAbrasive Liquid Transfer
vCement Grouting
vSpillage Clean-Up
vEffluent Handling
vDirect Transfer to Height / Long Horizontal Distance
vPetroleum Product Handling
vRemote Location
vEmergency Stand by Duty
vPump for sensitive liquids , Bio-Gas Plants , Essential Oils , Food , Milk Products
vPump for abrasive liquids, machine coolants, etc
this pumps are made with flame proof / explosion proof motor these pumps are self priming type, centrifugal type, vertical sump pump type, mud pump type, gear type, multistage pump type, or any other type pump can be made as per requirement of customer. These pumps are widely used to handle, petrol, kerosene, diesel, oil and solvents handling motors, can be available with cmr, (dgms certificate on request material or pumps & sealing arrangement can be made as per customer requirements or as per material to be handled. We assure prompt delivery & presales and after sales service
explosion proof motorexplosion proof pumps prevent internal or external explosions by enclosing parts that could ignite either the transfer media or the surrounding atmosphere. Some explosion-proof pumps are designed to move abrasive materials, acids, adhesives, chemicals, concrete and grout, coolants, hazardous materials, liquid metal, or lubricants. Other devices are rated for combustible, corrosive, high viscosity, or high temperature media. Explosion-proof pumps are also used to move gasoline, diesel fuel, and oil; ground water, potable water, salt water, and wastewater; sewage, sludge, slurry and ash slurry; gas and air; powders, solids, and rendering wastes; and a variety of liquids and liquids with solids.
many types of explosion-proof pumps are available. Bladder pumps are low-flow pneumatic devices used in sampling applications. Canned motor pumps feature an enclosed electric motor and an inner rotor that is directly connected to the pump impeller. centrifugal pumps apply centrifugal force to generate velocity, use rotating impellers to increase velocity, and push fluids through an outlet valve. Diaphragm pumps include suction and discharge check valves to prevent backflow. piston and plunger pumps use a plunger or piston to move media through a cylindrical chamber.
manually powered pumps rely upon hand or foot power.explosion-proof pumps are used in a variety of commercial, industrial, municipal, and maritime applications. Examples include agriculture and horticulture, dairy farms, breweries and distilleries, construction, flood control, food service and food processing, power generation, and oil and gas production. Explosion-proof pumps are also used in the aerospace and defense, automotive, machine tool, mining, medical, pharmaceutical, semiconductor, and paper industries. Devices for heating, ventilation and air conditioning (hvac) systems are also available. Cryogenic pumps are rated for conditions where temperatures are low enough for gases to condense to become liquids or solids. Petrochemical and hydrocarbon pumps are rated for materials such as gasoline, kerosene, diesel oil, lubricating oil, paraffin wax, and asphalt. Contact us forsealless pump supplier, flame proof pumps, malharpumps.com
A Range of high quality positive displacement gear pumps for fuel injection in industrial burners. These pumps provide fuel at finely controlled pressure and flow rates for optimum combustion resulting inlong term fuel saving and reduced pollution.
effluent treatment:- raw sewage water digested & activated sludge drained sludge up to 40% dry contents.
chemicals:- acidic & alkaline slurry dyes alum , viscous adhesive dispersion & emulsion detergent slurry soap slurry. dairy :- milk , butter , cream , crystal , paste , soft cheese , cottage cheese.
fruits & vegetable processing :- fruits & vegetable juices & pulp tomato pulp. sweets & confectioneries :- glucose , chocolate compounds jams , honey, paints & warnishes :-dispersion paints , printing ink , oil pasters , solvent binding agent , high viscous oil verosore oil / furnace oil / lubricating oil / grease. pulp & paper :- alum solutions , high consistency pulp , coating paint , glues , milk of lime , sludges. sugar & distilleries :- juices , magma syrups , molasses , waste water sludge.
housing parts pump :- gray ci (is 210 fg 220) , rubber / frp lined , ss-304, ss-316 & special alloys. stator : natural , nitrile, nerprene , epdm , hyplon , viton , food grage & special quality rubber. rotor : heat trated tool steel , ss-304 & ss-316 and other special alloys rotating parts :- tool steel , ss-304 , ss-316 and other special alloys
self priming
non clogging
positive displacement
pulsation free delivery
temperature up to 200c
flow rate proportional to pump speed
pumping direction reversible
can handle high percentage of solids output up to 200m3/hr,
vulcanized stator simple to be changed
high resistance to wear
simple construction
easy to dismantle & assemble
pressure 6 up to 30kg/cm2 even at small quantities or low speed
no valves essential for delivery
we are counted among the leading suppliers of exclusive quality thermic fluid pump to our valued customers. These pumps are manufactured from best quality stainless steel and cutting-edge technology. Offered pumps are appreciated for their noise and vibration free performance, easy installation and high degree interchangeability. Our pumps are suitable for both organic and inorganic fluids and used in oil refineries, paper, food, chemical, textile industries and sea water desalination plants. These pumps are equipped with water / self cooling feature that makes them suitable for the applications in heat transfer plants and handling of organic heat transferring of oils. In compliance with the latest industry standards, these pumps are designed with heavy duty bearings.
low maintenanceeasy to operatelonger service life.
capacity up to 250 m3/hrtemperature up to 350ctdh up to 95 mlcworking pressure up to 20 barsdelivery size up to 100 mm.speed n- :- 960/1450/2900 rpm
industries covered
pharmaceuticals & chemical :- oil extraction plantspulp & paper industries :-waste oil refining plantsstarch industries :- air-conditioning heating plantseffluent treatments plants :-cooling tower water circulationdyes & intermediates :- solvent transferro & dm water plants: thermic fluid circulation.
pumps are manufactured in variety of materials such as carbon steel / wcb as per astm / din standardsstainless steel as per astm a 351/743 gr. Cf8/cf8mcarbon steel (wcb) / alloy steelcf-8 , cf-8m cf-3 , cf-3m (ss-316l) , alloy 20 , cd4mcu
casing :- volute type , back pull out , centre line top discharge , end suction , integrally cast feet, center line support casing if required
shaft sleeve :- easily replaceable , hardened , compatible , supply of thermic fluid
sealing arrangement :- graphite packing in gland box having cooling chamber that ensure to pass cooling water and safeguard graphite packing life.
mechanical seals :- single spring / metallic bellow
impeller :- enclosed type , provided with back vanes to reduce pressure on stuffing box and to minimize axial thrust and gland leakage, high hydraulic and mechanical efficiency.
bearing housing :- reinforced and standard and bearing assemblies which are perfect for high temperature as well as high suction pressure of 0.05 mm. It is available with constant level oiler
flanges :- enclosed flange rating pn 16 and drilled to din standard to meet iso 2858 requirements.
throat ring / bush :- it is perfectly designed to reduce the pressure on stuffing box. Also it helps to increase the life of graphite packing.
designed for :- circulation of heat oil transfer
jacketing for cooling offered for s/box , casing pedestal and bearing-housing, standard bearing / special heavy duty bearing arrangements available.
ach type pumps are used in chemical & petrochemicals industry, food industry, dyeing , sugar industry, paper & pulp industry, fertilizer units & etc. Handling of all types of liquids , acids , alkalis , dyes , hydrocarbons , corrosive slurries (solids up to 15 mm) , green , black liquor , pulp (consistency up to 2%) & etc.
design
horizontal back pull out design pumps. Open and semi open impeller construction with one cylindrical roller bearing on pump end, one double row angular contact ball bearing on drive end designed in accordance with ansi b 16.5
back pull out centrifugal designsteady flowenergy efficientsturdy constructionlow npshnoise & maintenance freeenvironment friendlyshaft defection below 0.05 mmsimple external axial adjustment for impeller wear & tearbearing life-more than 17000 operating hours*.
Capacity | Up to 600 M3/Hr |
Head | Up to 180 Mtrs (590 Feet) |
---|---|
Temperature | Up to 200° C (392° F) |
Casing Pressure | Up to 24 Kg / cm2 |
Pump size ( Delivery bore) | DN 25 mm to DN 200 mm |
Speed | Up to 2900 rpm |
Direction of rotation | Clockwise from drive end |
idle for pressure booster application very useful for small ro / soda plant (replacement of rotary vane pump) excellent for drinking water application as all parts are of brass ( 100 % hygiene) curing at constriction site max suction lift 8 mtr very silent, no need of foot valve doubled z sealed precision ball bearings tefc motor.
.
HEAD IN MTRS | 10 | 20 | 30 | 40 | 50 | 60 | 70 | 80 | 90 | 100 | 110 |
---|---|---|---|---|---|---|---|---|---|---|---|
CAPACITY LPM | 32 | 30 | 28 | 22 | 20 | 19 | 16 | 14 | 12 | 8 | 0 |
The most suitable method of Installation will depend on the pumping application. The simplest and most widely adopted method is mount the pump close to the feed tank at such a level that the impeller is flooded and the pump therefore pumped when the liquid reaches a certain height in the tank.The pump will Deliver liquid until the suction pipe becomes uncovered , when it will run dry until the liquid level is restored to the point where re-printing can take place, this cycle of operation may be repeated indefinitely. Contact vertical glandless pump supplier, vertical glandless pump manufacturer today. The Vertical glandless pump is vertical molded Polypropylene corrosion resistant pumps.Pumps for Leakproof and Maintenance free pumping of corrosive and Abrasive Liquids.
mvgp pumps are vertical molded polypropylene corrosion resistant pumps.pumps for leakproof and maintenance free pumping of corrosive and abrasive liquids.
the malhar pump is similar hydraulic design to any conventional centrifugal pump. It differs in so far as it is always mounted in the vertical position. A restriction is provided above the impeller and need for any from of liquid seal is obylated by allowing a small leakage to escape by way of an overflow connection in the upper pump body return to suction vessel.
the most suitable method of installation will depend on the pumping application. The simplest and most widely adopted method is mount the pump close to the feed tank at such a level that the impeller is flooded and the pump therefore pumped when the liquid reaches a certain height in the tank.the pump will deliver liquid until the suction pipe becomes uncovered , when it will run dry until the liquid level is restored to the point where re-printing can take place, this cycle of operation may be repeated indefinitely. Contact vertical glandless pump supplier, vertical glandless pump manufacturer today. Thevertical glandless pumpis vertical molded polypropylene corrosion resistant pumps.pumps for leakproofand maintenance free pumping of corrosive and abrasive liquids.
the recognizable leading improvement is the deletion of problems get to your feet from the use of powered seal, insulation box and inside bearing.the aptitude of pump to run dry eliminates single reason of interruption which is regularly attributable to the human component this feature is very convenient in process needing continuous transference of a corrosive fluid with a high gradation of reliability e.g. Disposal of acid effluent.the glandless pumps lend itself to process incorporating automatic control of a pump discharge valve. The controlled leakage acts as an integral by-pass. The pump suffers no ill effects if the discharge valve is partially or fully closed.the maximum main improvements to be derivative from the use of glandless pump are in the province of maintenance and following reduction in down time invention victims. Normal maintenance on the glandless pump is confined to lubrication of the driving.
no mechanical seal, stuffing box and internal bearings provided.no maintenance since the pump can even run dry indefinitely as there is no packing, bushes or internal bearings.reduction of downtime production losses in view of above features.all the wet-end parts are in solid molded construction to with stand corrosion and erosion.the impeller is semi-open type used in our all-vertical pumps to suit both clear and polluted fluids.pump mounted outside the suction tank and is not submerged type.polypropylene are manufactured by solid injection molding process with high pressure hence.
pp 50 to 80 cpph 90 to 100 cpvdf 100 to 115c
because glandless pumps do not have any packing bush or internal bearing, full advantage can be taken of available drive speeds. The pump may be run at 1450 and 2900 rpm respectively and a range of impeller diameter for each pump size gives a wide spread of performance.in general the range cover flow up to 100m3/hr. And discharge head up to 50 meters.
Vertical Centrifugal process pump can be used in any installation or specially where the saving of space is important factor and most important where liquid is difficult to lift because of nature like temp , corrosiveness etc These pump are designed for use where the liquid handled to be is of highly corrosive Nature or where non adherence of product or zero metallic contamination is must These pumps are equally ideal for continuous or intermittent service for handling Corrosive as well as ultra pure chemicals without fear of corrosion or contamination.
Head - 3 to 76 meters
Capacity up to 1890 LPMSize 12 mm to 100 mm
Pumps which We deliver has.
|
Model |
Hp |
Size |
Head in Metres Discharge in LPM at 2900 RPM |
|||||||||||||
3 |
5 |
7 |
10 |
12 |
15 |
17 |
20 |
22 |
25 |
27 |
30 |
35 |
40 |
|||
SPCFS-1 |
0.25 |
12 x 12 |
40 |
32 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-2 |
0.5 |
25 x 25 |
- |
100 |
45 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-3 |
1 |
25 x 25 |
- |
- |
140 |
120 |
70 |
35 |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-3A |
1 |
38 x 38 |
- |
- |
181 |
95 |
50 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-4A |
1.5 |
38 x 38 |
- |
- |
- |
- |
160 |
130 |
90 |
75 |
- |
- |
- |
- |
- |
|
SPCFS-4B |
1.5 |
50 x 50 |
- |
- |
- |
250 |
166 |
85 |
- |
- |
- |
- |
||||
SPCFS-5A |
2 |
38 x 38 |
- |
- |
- |
- |
225 |
190 |
155 |
105 |
78 |
40 |
- |
- |
- |
|
SPCFS-5B |
2 |
50 x 50 |
- |
- |
330 |
250 |
160 |
80 |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-6A |
3 |
50 x 38 |
- |
- |
- |
- |
- |
250 |
220 |
180 |
135 |
108 |
50 |
|||
SPCFS-6B |
3 |
50 x 50 |
- |
- |
- |
- |
- |
330 |
300 |
280 |
225 |
150 |
85 |
- |
- |
- |
Model |
Hp |
Size |
Head in Metres Discharge in LPM at 2900 RPM |
|||||||||||||
16 |
20 |
24 |
28 |
32 |
36 |
40 |
44 |
48 |
||||||||
SPCFS-7A |
5 |
50 x 38 |
- |
- |
260 |
230 |
190 |
145 |
90 |
- |
- |
|||||
SPCFS-7B |
5 |
65 x 50 |
400 |
370 |
300 |
230 |
180 |
- |
- |
- |
- |
|||||
SPCFS-8A |
7.5 |
50 x 38 |
- |
- |
290 |
280 |
250 |
225 |
190 |
120 |
60 |
|||||
SPCFS-8B |
7.5 |
65 x 50 |
500 |
450 |
385 |
280 |
230 |
- |
- |
- |
- |
|||||
SPCFS-9A |
10 |
50 x 38 |
- |
500 |
480 |
470 |
450 |
410 |
350 |
290 |
190 |
|||||
SPCFS-9B |
10 |
65 x 50 |
560 |
510 |
450 |
370 |
280 |
210 |
150 |
- |
- |
features:-
seal less
gland less
non magnetic driven
working principle: we have made shaft and stuffing box long and provide special arrangement in stuffing box with groove on shaft in such a way that liquid which come out from stuffing box will go back again to casing .
some liquid is may be come out but due to deep stuffing box it will remain in stuffing box and we have provide one hole in box which is connected to suction flange of pump by pipe line so liquid will again move to suction line and thus pump do not have any leakage from shaft .
this pump is very ideal for solvents , acids and corrosives liquids where maintenance of mechanical seal is costly and also time consuming .
our complete cf series pumps will be soon available with above features and after some time we also give pp pumps with same features.
.
Model |
Hp |
Size |
Head in Metres Discharge in LPM at 2900 RPM |
|||||||||||||
3 |
5 |
7 |
10 |
12 |
15 |
17 |
20 |
22 |
25 |
27 |
30 |
35 |
40 |
|||
CFLCFS-1 |
0.25 |
12 x 12 |
40 |
32 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
CFLFS-2 |
0.5 |
25 x 25 |
- |
100 |
45 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
CFLCFS-3 |
1 |
25 x 25 |
- |
- |
140 |
120 |
70 |
35 |
- |
- |
- |
- |
- |
- |
- |
- |
CFLCFS-3A |
1 |
38 x 38 |
- |
- |
181 |
95 |
50 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
CFLCFS-4A |
1.5 |
38 x 38 |
- |
- |
- |
- |
160 |
130 |
90 |
75 |
- |
- |
- |
- |
- |
|
CFLCFS-4B |
1.5 |
50 x 50 |
- |
- |
- |
250 |
166 |
85 |
- |
- |
- |
- |
||||
CFLCFS-5A |
2 |
38 x 38 |
- |
- |
- |
- |
225 |
190 |
155 |
105 |
78 |
40 |
- |
- |
- |
|
CFLCFS-5B |
2 |
50 x 50 |
- |
- |
330 |
250 |
160 |
80 |
- |
- |
- |
- |
- |
- |
- |
- |
CFLCFS-6A |
3 |
50 x 38 |
- |
- |
- |
- |
- |
250 |
220 |
180 |
135 |
108 |
50 |
|||
CFLCFS-6B |
3 |
50 x 50 |
- |
- |
- |
- |
- |
330 |
300 |
280 |
225 |
150 |
85 |
- |
- |
- |
application
all non pp parts lined with anti corrosive paint to protect corrosive atmosphere
Head - 3 to 76 meters
Capacity up to 1890 LPMSize 12 mm to 100 mm
Pumps which We deliver has.
|
Applications : |
|
Features :
|
Thickness of sheet depend upon size and pressure of system .
WATER RATING CHART OF :SPCFS: :-
"CFS" SERIES |
||||||||||||||||
Model |
Hp |
Size |
Head in Metres Discharge in LPM at 2900 RPM |
|||||||||||||
3 |
5 |
7 |
10 |
12 |
15 |
17 |
20 |
22 |
25 |
27 |
30 |
35 |
40 |
|||
SPCFS-1 |
0.25 |
12 x 12 |
40 |
32 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-2 |
0.5 |
25 x 25 |
- |
100 |
45 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-3 |
1 |
25 x 25 |
- |
- |
140 |
120 |
70 |
35 |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-3A |
1 |
38 x 38 |
- |
- |
181 |
95 |
50 |
- |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-4A |
1.5 |
38 x 38 |
- |
- |
- |
- |
160 |
130 |
90 |
75 |
- |
- |
- |
- |
- |
|
SPCFS-4B |
1.5 |
50 x 50 |
- |
- |
- |
250 |
166 |
85 |
- |
- |
- |
- |
||||
SPCFS-5A |
2 |
38 x 38 |
- |
- |
- |
- |
225 |
190 |
155 |
105 |
78 |
40 |
- |
- |
- |
|
SPCFS-5B |
2 |
50 x 50 |
- |
- |
330 |
250 |
160 |
80 |
- |
- |
- |
- |
- |
- |
- |
- |
SPCFS-6A |
3 |
50 x 38 |
- |
- |
- |
- |
- |
250 |
220 |
180 |
135 |
108 |
50 |
|||
SPCFS-6B |
3 |
50 x 50 |
- |
- |
- |
- |
- |
330 |
300 |
280 |
225 |
150 |
85 |
- |
- |
- |
Model |
Hp |
Size |
Head in Metres Discharge in LPM at 2900 RPM |
|||||||||||||
16 |
20 |
24 |
28 |
32 |
36 |
40 |
44 |
48 |
||||||||
SPCFS-7A |
5 |
50 x 38 |
- |
- |
260 |
230 |
190 |
145 |
90 |
- |
- |
|||||
SPCFS-7B |
5 |
65 x 50 |
400 |
370 |
300 |
230 |
180 |
- |
- |
- |
- |
|||||
SPCFS-8A |
7.5 |
50 x 38 |
- |
- |
290 |
280 |
250 |
225 |
190 |
120 |
60 |
|||||
SPCFS-8B |
7.5 |
65 x 50 |
500 |
450 |
385 |
280 |
230 |
- |
- |
- |
- |
|||||
SPCFS-9A |
10 |
50 x 38 |
- |
500 |
480 |
470 |
450 |
410 |
350 |
290 |
190 |
|||||
SPCFS-9B |
10 |
65 x 50 |
560 |
510 |
450 |
370 |
280 |
210 |
150 |
- |
- |
Applications and Industries:
Irrigation Sprinkler Installations
Pressure Boosting Multistage story Building Hydro Pneumatic
Water Works Fire Fighting Mining wash down Applications
Hydraulic press / Circuits transfer & circulation hot & cold water
Boiler feed pumps Condensate pumps
Features:
Single Stage Pump ISL Series are primarily designed to handle water and are suitable for handling water in water supply systems for domestic and industrial use.Single stage pumping units of compact design with back pullout feature with suction & discharge flange arranged in-line opposite one another for direct installation in the pipeline.Motor and pump are close coupled by rigid coupling. The completer rotating portion can be removed without disconnecting the pump casing from the connecting pipe line
MALHAR Volute casing IN-LINE centrifugal pumps Type MIL are space saving pump units designed for easy installation and are used generally for circulating clean non-aggressive fluids.
Water Supply SystemsWater circulation / TransferHot water CirculationAgriculture
IndustryShip BuildingCooling TowersAnd many other Applications
Direction of Rotation : Clock wise looking from the motor end at the pump. Shaft Sealing : The Shaft is sealed by means of a Mechanical seal. Wearing Ring : Every Volute Casing is fitted with a Replaceable wearing ring. Casing Gasket : The Volute casing is sealed be means of a flat gasket
mhpp pumps are single stage horizontal molded polypropylene corrosion resistant pumps. The pump has similar hydraulic design to any conventional centrifugal pump. Standard dimension process pumps with mechanical seal/ gland packing arrangement. Pump required at all of the chemical industries. These pumps give you unusual protection against corrosive & abrasive.
water treatment planteffluent treatmentfilter press for dyes and chemicalsfertilizer plants thermal and atomic power plantsdrugs & pharmaceutical industriesdescaling of tubesscrubbing of corrosive gases like c12 , br , I so2 , nh3 , f2 etc.excellent for vacuum ejectorstransferring of concentrated hcl from road tankerspaper & pulp industriespickling in steel rolling mills
caustic soda plants :- chlorinated brine , conc , hcl , dilute h2so4 etc. phosphoric acid plants :- h3po4 , h2so4 , hf and their mixtures with or without solid (gypsum) up to 40% conc. gas washing plants :- scrubbed liquids containing cl2 , br2 , f2 , i2 , so2 , so3 , co2 , nh3 , gases etc. With solids replace hast alloy. rayon plants :- spin bath solution (h2so4 , znso4 , naso4 , etc.) electro palting
pp 50 to 80 cpph 90 to 100 cpvdf 100 to 115c
features:-
| |
applications:-
|
features:-
application:-
rotary gear pumps are widely used in paper mills, refineries, steel mills and textileindustries
Additional Information:
Payment Terms : T/T
The SIG pumps are based on the proven rotary trochoidal design gerotor principale.
The pumps are designed to meet specific demands of OEMs
The reliable performance of the SIG series makes them an ideal choice for various industrial applications.
SPECIAL EXECUTIONS:-
ADVANTAGES OF SIG PUMPS
Parts / Pumps interchangeable with well known brands
TYPICAL APPLICATION
LIQUIDS HANDLED
APPLICATIONS FOR HYDRAULIC TESTING OF
applications for hydraulic testing of
special features
.
applications :
.
The pumps are non self priming vertical multistage centrifugal pumps designed to occupy minimum floor space. Unlike other pumps with sheet metal and plastic fabricated components, our pumps have components all cast in various metals like cast iron , bronze, stainless steel 304 & 316.
Excessive axial trust is balanced by assembling the pump stages with equal number of opposed impellers. Balancing of axial thrust allows the use of standard flange mounted motor without special bearings. Pressure on mechanical seal reduces to half the working pressure due to opposed impellers. the shaft is well supported in bush bearings making operation noise less. The maintenance is easy & in expensive.
The pumps are primarily designed to handle water and are suitable for handling hot & cold water supply systems for domestic and industrial use
RANGE : UP TO 4 OUTLET SIZE
MAXIMUM HEAD 280 METER
MAXIMUM CAPACITY 90 M3/HR
SUCTION X DELIVERY SIZES :- from 32 mm to 100 mm
CAN HANDLE LIQUIDS UP TO 120C
Direction of Rotation : Clock wise looking from the motor at the pump.
Shaft Sealing :- The Shaft is sealed by means of a Carbon- Ceramic, SC/SC, TC/TC Mechanical Seal.
Carbide Bushes :-The Bottom casing is fitted with Tungsten carbide Motor support.
Casing Gasket :- The Outer Shell is sealed by means of flat Gaskets.
Foundation Base :- Cast Iron
Highly Efficient Hydraulics Design
Fabricated Components
Less Friction in system (Pressed Components)
No Expensive Foundation Required
Easy Installations
Small Floor Space.
Vertical multistage centrifugal pumps type MC are designed for a wide range of applications.
Water supply systems.
Water Circulation /Water Treatment Plant
Hydro Pneumatic Systems / Condensate transfer.
Agriculture /Industrial Washing
Coolant Circulation.
Boiler Feeding / Fire Fighting / Booster Applications.
Ship Building / RO-DM Plants.
Sprinkle Irrigation.
a wide range of vertical pumps are available for handling clear water or contaminated water application. These pumps are designed to operate at 50hz and 60hz , in single or more than one stages according to head required. These pumps consisting of bowl assembly, column pipe-assembly, bearing housing assembly along with n.r.r (non reverse ratchet) assembly & motor stool/driving unit assembly.
capacities up to 20, 000 m3/hr,
head up to 300 mtrs.
bowl sizes from 100mm to 1600 mm
self-water lubrication, oil lubrication external water lubrication
motor water lubrication]
combination motor-gear drive above ground / under ground discharge
standard / special material of construction.
general water pumping /conveying used for various industries.
spray and injection water in sugar industry.
cooling tower circulation.
irrigation and drainage for agriculture.
process and cooling water pumps for power plants.
fire fighting.
tube well irrigation / open well irrigation and river / canal irrigation
sprinkle irrigation
urban water supply / rural water supply
domestic water supply in high rise building and water fountain.
raw & threaded water services / mine dewatering.
fire fighting services.
on line boosting
oil / petroleum handling services.
vertical pumps take little space in plan since the liquid in led away to the axis of shat.
the impeller is submerged, so pump does not require to be primed and is always ready to use.
the suction condition also prevents the caviation in the pump and pitting in impeller & diffuser.
due to positive head at suction the pump gives its rated performance as well as high ovarall efficiency, whereas in horizontal pumps due to losses in suction line, foot valve etc. The rated performance of the pumps is not achieve.
bowl assembly:-
bowl assembly consists of suction bell , impeller , bowl, pump shaft.
suction bell:-
suction bell designed for smooth & steady entrance of liquid with minimum losses.
bowl :-
the bowl is a casing with diffuser vane cast integrally to reduce the velocity of the liquid coming from impeller & increasing the pressure.
impeller:-
impellers are of open (propeller), semi-open (mixed flow) & closed (vertical turbine) type depending upon the specific speed of pumps and are accurately machined , dynamically & hydraulically balanced.
shaft:-
the shaft is of high tensile strength steel.
column pipe assembly:-
it consists of column pipe, line shaft & line shaft bearing. column pipe:-
casted or fabricated, it houses line shaft bearing retainer. line shaft bearing:-
line shaft bearing provided in leaded bronze shell with cut less rubber (natural/synthetic) bearing lubrication self or pressurized external water.
trust bearing assembly:-
anti friction bearings are provided to take care of axial thrust & weight of rotor assembly as well as radial load. Lubrication with oil/grease non reverse ratchet are provided with thrust bearing housing assembly to avoid the rotation of impeller (pump) in opposite direction causing opening of the threaded coupling.
discharge head / discharge elbow:-
either cast of fabricated designed to direct flow from column pipe to discharge pipe. It may be on ground level or below ground level.
motor stool:-
m.s fabricated heavy duty to ensure vibration free operation.
couplings:-
for line shaft threaded barrel or muff type coupling as per requirement. For pump to motor pin bush flexible coupling are provided.
direction of rotation:-
counter clock wise when viewed from driving end.
Stainless steel centrifugal pump stainless steel centrifugal monobloc and bare pumps (coupled). These pumps are made from ss-304 or ss-316 sheet. The pumps are precisely fabricated . These pumps wetted parts are of stainless steel and widely used in chemical and process industries. As these pumps are fabricated from steel, it is also widely used in dairy, food and beverages industries, wine , RO and DM plant , sea water applications. These pumps are available from 0.25 HP to 30 HP . head up to 90 meter and capacity up to 3000 LPM. The unique feature is international quality at affordable price with minimum delivery period.
Polypropelene Pumps
Features : | Monobloc Pump |
|
Performance are at 2900 RPM, 50Hz and tested with clear water.
Due to constant R & D activity, details are subject to change without prior notice.
Application :
Phosporic acid plants, Gas washing plants, Rayon plants, caustic joda plants for corrosive acids & basics, effluent treatment handling.
Performance Chart (with semi open impeller) |
Model | H.P. | Size | Head in Mtr. | |||||
6 | 8 | 10 | 12 | 16 | 20 | |||
PP -2 | 0.5 | 25 x 25 | 0 | 120 | 110 | 90 | - | |
PP -3 | 1 | 25 x 25 | 0 | 150 | 142 | 118 | 60 | - |
PP -4 | 1.5 | 40 x 25 | 0 | 162 | 148 | 120 | 90 | 44 |
The SIG pumps are based on the proven rotary trochoidal design gerotor principale. The pumps are designed to meet specific demands of OEMs The reliable performance of the SIG series makes them an ideal choice for various industrial applications.
SPECIAL EXECUTIONS:-
ADVANTAGES OF SIG PUMPS
| |
TYPICAL APPLICATION
LIQUIDS HANDLED
|
applications:-malhar volute casing in-line centrifugal pumps type mil are space saving pump units designed for easy installation and are used generally for circulating clean non-aggressive fluids.
motor option:-
standard pumps are fitted with motor adaptor suitable for mounting vertical flange mounting v-1 frame motor, to suite particular specification where protection class & enclosure are required . Special suitable adaptor can be provided.the pumps is coupled with a electric motor , which is totally enclosed , fan cooled squirrel cage motor. Single-phase motors have a built in thermal overload protection.three phase motors should be protected by a suitable motor starter as per local regulations.
nominal speed :- 2900/1450 rpm,
range:-
capacity : up to 280 m3/hr
head : up to 95 mtr
higher capacity and head available on request
Vertical Centrifugal process pump can be used in any installation or specially where the saving of space is important factor and most important where liquid is difficult to lift because of nature like temp , corrosiveness etc These pump are designed for use where the liquid handled to be is of highly corrosive Nature or where non adherence of product or zero metallic contamination is must These pumps are equally ideal for continuous or intermittent service for handling Corrosive as well as ultra pure chemicals without fear of corrosion or contamination
vertical centrifugal process pump can be used in any installation or specially where the saving of space is important factor and most important where liquid is difficult to lift because of nature like temp , corrosiveness etc these pump are designed for use where the liquid handled to be is of highly corrosive nature or where non adherence of product or zero metallic contamination is must these pumps are equally ideal for continuous or intermittent service for handling corrosive as well as ultra pure chemicals without fear of corrosion or contamination.
high temperature services : maximum working temperature is 110 c / 200 c.
length : pumps lengths available from 1 to 12 with flow rate up to 50m3/h or120 meter head. Higher capacities and head available on request and even multistage pump can be also made .
models : available in conventional or tailor-made configuration. Several models such as suction extension with float switch, duplex pumping station with float switch (auto on/off device) also available.
bearing free design for handling abrasives in solutions.motors are flange mounted single or three phase tefc from 1 hp to 100 hp .epoxy / polyurethane paints are used on metallic bearing housing.radial vanes on backside of impeller increase flow or fluids through the sleeve bearing preventing overflow at top of column.lubrication of bearings by product itself or by fresh water.all models operate at 1450 rpm / 2900 rpm (variable speed motor available )specially designed vapor seal provided to protect bearing from corrosive fumesdynamically balanced impeller.
these pumps are in extensive use in the fields ofpollution control.filtration .transferring corrosive chemicals .slurries .bio gas plants.sewage.waste water treatment plant.phosphoric acid plant.h, po, h2sifs, h2so4, hf and .their mixtures.gas washing plant .scrubbed liquids containing , f, cl, so2, ammoniawater treatment plant .any types of acidic water lifting .m.s vertical pump are used for transfer of sulphuric acid 98 %. Olum, cloto, neptha
no mechanical seal or stuffing box requiredconstruction withstand corrosion & erosionno foot valve required to lift from negative suctionno leakages problem just like gland or mechanical sealnormal maintenanceeasy alignment
small size bare / monobloc poly propylene pumps. Fitted with seal / gland or ptfe bellow mechanical seal. Shaft is of ss-304 / 316 with ceramic coating and (ptfe coating ptional) very economical models as pumps made with minimum parts. Very easy maintenance.
phosphoric acid plants, gas washing plants, rayon plants, caustic soda plants for corrosive acids & basics, effluent treatment handling.
performance are at 2900 rpm, 50hz and tested with clear water.due to constant r & d activity, details are subject to change without prior notice
Model | H.P. | Size | Head in Mtr. | |||||
---|---|---|---|---|---|---|---|---|
6 | 8 | 10 | 12 | 16 | 20 | |||
PP -2 | 0.5 | 25 x 25 | 0 | 120 | 110 | 90 | – Discharge in LPM | |
PP -3 | 1 | 25 x 25 | 0 | 150 | 142 | 118 | 60 | – |
PP -4 | 1.5 | 40 x 25 | 0 | 162 | 148 | 120 | 90 | 44 |
Small size bare / monoblac poly propelene pumps.
Fitted with seal / gland or PTFE bellow Mechanical seal.
Shaft is of SS-304 / 316 with ceramic coating and (PTFE coating optional)
Very economical models as pumps made with minimum parts.
Very easy maintanance.
Performance are at 2900 RPM, 50Hz and tested with clear water.
Due to constant R & D activity, details are subject to change without prior notice.
Application :
Phosporic acid plants, Gas washing plants, Rayon plants, caustic joda plants for corrosive acids & basics, effluent treatment handling.
Model | H.P. | Size | Head in Mtr. | |||||
6 | 8 | 10 | 12 | 16 | 20 | |||
PP -2 | 0.5 | 25 x 25 | 0 | 120 | 110 | 90 | - | |
PP -3 | 1 | 25 x 25 | 0 | 150 | 142 | 118 | 60 | - |
PP -4 | 1.5 | 40 x 25 | 0 | 162 | 148 | 120 | 90 | 44 |
operation advantages of glandless pump:-
| |
sailent features of vertical glandless pump
temperature resistance
|
zyb50/zyb80vanepumpbuiltinairseparator, bypassvalve, filteris withthreedifferenttopcoversfor differentconnectingpipes.atype, btypeandc type.withtheadvantageoflownoise, highflowrate, longlife servicesetc.
.
MODEL |
FLOW L/MIN |
HEAD IN MTRS |
POWER KW |
SIZE MM |
IMPELLER/ OUT LET MATERIAL |
PUMP TUBE MATERIAL |
MBALSB-2 |
110 |
7 mtr |
1.1 |
50/25 |
plastic |
ALUMINIUM |
Fitted with ON-OFF Switch,
Available with Flame proof Motor Also (NON CMRI)
MATERIAL OF CONSTRUCTION:- ALUMINIUM PIPE TUBE , PLASTIC IMPELLER MS SHAFT
MEASUREMENT:- 145 X 33 X 22 cm
IN Bulit Filters
HEAD IN MTRS |
0 |
5 |
10 |
12 |
CAPACITY IN LPM |
40 |
30 |
15 |
SHUT OF |
AMPERE |
2.4 |
2.3 |
2.3 |
2.3 |
Fitted with ON-OFF Switch,
Available with Flame proof Motor Also (NON CMRI)
MATERIAL OF CONSTRUCTION:- PP PIPE TUBE , PP IMPELLER AND ALLOY 20 SHAFT
MEASUREMENT:- 145 X 33 X 22 cm
IN Bulit Filters
HEAD IN MTRS |
0 |
5 |
10 |
15 |
20 |
23 |
CAPACITY IN LPM |
43 |
31 |
26 |
16 |
6 |
SHUT OF |
AMPERE |
2.8 |
2.5 |
2.5 |
2.5 |
2.2 |
2.0 |