Capcab India Limited

Punjabi Bagh, Delhi

We are counted amongst most dynamic Compensating Leads Manufacturers based in India. Our superior quality compensating leads are highly endowed. We carry a vast range of high temperature compensating leads. We offer highly affordable rates for these extremely durable high temperature compensating leads.Cable Code: KX, KX(A), TX, JX, EX, SX/RX, BX, NX, UX, WX. Construction:Single or Multiple Pairs. Conductor size: 16, 18&20AWG. Primary Insulation: General purpose PVC/HRPVC/PTFE/Fiber Glass. Screening:Individual and/or overall with Aluminium Mylar/Copper Tape or with Tinned, Bare, Nickel Copper/Stainless Steel. Inner Sheath:PVC/HRPVC/FRLS PVC/LDPE/PTFE/Fibre Glass. Armouring:GI round wire/Flat strip. Outer sheath:PVC/HRPVC/FRLSPVC/LDPE/PTFE/Fibre Glass. Rip cord:For easy removal of sheath. Note:Other conductors size and Insulation materials on request.

For Trouble Free Working, These Connecting Cables are Just as Important as Winding are for the Submersible Pump Motors. 3 Core Flat Cables are Manufactured Keeping in Mind the Severe and Difficult Conditions in Which They are Required to Operate. the Individual Flexible Conductors are Made from Electrolytic Grade Bright Copper. the Wires are Drawn, Annealed and Bunched Properly to Ensure Long Life. Each of These Three Flexible Copper Conductors is Insulated with a Specially Formulated Pvc Compound and the Cores are Laid Up in Flat Parallel Position. the Outer Sheath of the Cable is Made from a Special Grade of Resistant Pvc Compound Impervious to Water, Grease, Oil Etc.

Selecting the Correct Type and Size of Cable for the Desired Application is Very Important for Any Electrical Project Because the Performance of all Equipment Largely Depends Upon the Performance of Cables. apart from the Technical Suitability and Conformance the Cost of Every Equipment Has Become Another Important Aspect. the Designers and Consultants are Constantly Focusing On Economically Viable Proposals in Selecting the Equipment. selecting the Correct Type and Size of Cable Not Only Ensures the Trouble Free Performance But also Optimizes the Cost of Equipment, Installation and other Operation as Well. keeping in View These Aspects, We Can Provide the Correct Type and Size of Cable if We Get the Following Information Along with the Enquiries of the Cables:supply System: system Earthing : Solidly Earthed or Non-effectively Earthed. voltage Grade : Rated and Maximum System Voltage. Permissible Voltage Drop if to Be Considered. current Rating : Type and Magnitude of Current (continuous, Cyclic or Fluctuating). fault Current : System Fault Level or Short Circuit / Earth Fault Current with Duration in Seconds. constructional Detail: conductor : Aluminium or Copper , Number of Cores and Size. screen : Screened or Unscreened inner Sheath : Taped or Extruded or Fr/frls Pvc outer Sheath : Armoured or Unarmoured. if Armoured Then Flat Strips or Round Wires armour : Normal St 2 Pvc or Fr / Frls Pvc drum Length : Any Specific Drum Length with Tolerance drum Size : Any Limitations On Dimensions / Weight of Drum installation Details: installation in : in Ground or in Air or in Duct . Whether Exposed to Direct Sunlight. conditions : Type of Soil and Any other Abnormal Climatic Conditions Viz. Chemical / Fire Hazards. Route Length and Number of Circuits.

We are Offering Computer Cables

To meet the needs of today's sophisticated, high speed, wide band with electronics, over long distances with a minimum of single loss, " CapCab" offers a wide range of coaxial and twin axial cable, included standard RG- type coaxial constructions in the more popular 50, 75, and 93, designs, miniature coaxial products for smaller high speed applications as well as various coaxial products to meet the stringent requirements of the Ethernet. Most of the cables are sweep tested using the vector network analyzer to insure very precise signal characteristics. APPLICATIONS:BROADCASTMATVCITIZEN BAND ANTENNARETRANSMISSIONLOCAL AREA NETWORK

We are one of the most energetic Cable Conductors Manufacturer and suppliers from India. Our superior quality cable conductors are far famed for their high efficiency. We present top quality power cable conductors, which are optimally durable. These high grade cable conductors are offered by us on very reasonable prices.

We are most progressive Instrumentation Cable Manufacturer and suppliers. Our data instrumentation cables are easy to install and designed to maintain high accuracy and sensitivity of system. Our instrumentation cables, ride herd on process variable which further may range from transducers to environmental controls. We also manufacture these instrumentation cables, as per the specifications given by clients.The company manufactures and stocks a wide range of Screened Instrumentation Cables needed for signaling systems, control and instrument circuits. These cables report and monitor process variables ranging from transducers to environmental controls and computer inputs. The carefully produced stranded copper conductors used in the cable maintain high system accuracy and sensitivity. Maximum rejection of electro magnetic noise is achieved by twisting the insulated conductors. Twisting causes the noise to be cancelled in adjacent sections of the wire. Maximum electrostatic noise rejection is achieved by shielding the cable with aluminium-mylar tape. An overall shield is normally provided and in critical applications an individual shield over each pair or triad is also provided. A minimum of 25% overlap of the shield ensures 100% coverage even when the cable is flexed. The drain wire under the shield provides continuous low resistance path to ground and simplified hook-up at grounding terminals. The cables can also be provided with copper braid screening. Ease of installation is another major benefit of these cables. Individual cores, pairs, triads or quads are colour coded and or number printed. A pair of communication wires can also be provided. The cables are available in a wide range of insulation and jacket materials, the most popular being PVC, Polyethylene, HR PVC, FRLS PVC, ZHLSF, Silicone, EPR & CSP rubber, Teflon. The detailed construction, conductor sizes and electrical characteristics are as mentioned below. The company also manufactures custom designed cables to meet the specific requirements of individual customer applications. Construction ConductorBare / tinned electrolytic annealed copper conductor. Solid, stranded or flexible confirming to BS 6360 and IS 8130. Refer Table 1 for details. Insulation PVC or HR PVC insulation in accordance with IS 5831. Polyethylene insulation in accordance with BS 6234 / IS 6474. Twisting and LayingRequired numbers of cores are laid up in case of multicore core cables. Individual pairs, triads or quads are formed by uniformly twisting the insulated cores with short lay lengths, prior to laying. Core IdentificationCores can be colour coded or number printed for easy identification. In case of multi pair cables one core in each pair is number printed in words as well as in figures at short intervals of 50mm or a numbered polyester tape is provided over each pair. Overall ScreenAfter final lay up of the complete cable an overall screen of aluminium-polyester tape is applied along with 0.5 sqmm multi stranded annealed tinned copper (ATC) drain wire in continuous electrical contact with aluminium side of the tape. Tinned copper braid screening can also be provided. Individual & Overall ScreenIndividual pairs, triads or quads are screened by aluminium-polyester tape along with 0.5 sqmm ATC drain wire and overall screened by aluminium-polyester tape as mentioned above. Tinned copper braid screening can also be provided. In case of individually screened cables for critical applications an extruded isolation sheath can also be provided over the individual screens. Assembly BinderAfter final assembly a non-hygroscopic polyester tape is provided to act as a binder as well as a bedding for the outer screening in all cables. ArmourGalvanized steel round wire or strip armour in accordance with BS 5308 / IS 1554 respectively. The armour wire and strip confirms to IS 3975. If required, G.I square interlock armour or G.I / S.S wire braid armour can also be provided. Inner & Outer SheathPVC, HR, FRLS PVC or ZHLSF sheath in accordance with IS 5831 can be provided. U.V stabilized Polyethylene sheath can also be provided for hazardous areas. A blue colour outer sheath for intrinsically safe areas can be provided on request. A pair of communication wires can be provided if desired.

We are a spanking wholesale Power Cables Manufacturer and suppliers based in India. We present best range of high voltage power cables. Our electrical power cables are highly efficient and safe. Furthermore, we offer highly competitive rates for these high grade electrical power cables.

 LT-XLPE Cables have a higher conductor rating i.e. "90°C as compared 70°C of PVC and hence higher current rating.Maximum temperature limit under Short Circuit conditions for LT-XLPE Cables is 250°C as against 160"C for PVC Cables. Hence, LT-XLPE Cables have higher Short Circuit rating.LT-XLPE Cables have higher emergency overload capacity than PVC Cables ( upto 60%).LT-XLPE Cables have longer life as compared to conventional PVC Cables.Tensile Strength for LT-XLPE Cables is 1.9 Kg/mm2 as against 1.25 - 2.5 Kg/mm2 for PVC Cables.Elongation (%) in LT-XLPE Cables is 300-500 as compared to 200-400 in PVC Cables.LT-XLPE Cables have high corrosion resistance in polluted atmosphere as compared to PVC Cables.LT-XLPE Cables have better properties of resistance to chemical and corrosive gases.LT-XLPE Cables have better properties to withstand vibrations, hot impacts.Dielectric strength (KV/mm) for LT-XLPE Cables is 40-50 as compared to 20-35 for PVC Cables.The moisture resistance of LT-XLPE Cables is nearly 100 times that of PVC.LT-XLPE Cables have low Installation cost because of light weight, dimensions and are far more flexible.Insulation resistance of LT-XLPE Cables is very high as compared to PVC (as high as 1000 times).LT-XLPE Cables are ideal for transmission and distribution of power.Jointing of LT-XLPE Cables is easier and quicker.Low temperature Brittleness Degree 0C for LT-J XLPE Cables is-90 against-15 for PVC Cables.

OVERALL DIAMETER AND CURRENT RATINGS (IN GROUND) OF 1.1 KV, 31/2 Core, XLPE / PVC INSULATED, PVC SHEATHED (ARMOURED AND UNARMOURED) CABLES.

Construction:Conductor

Bare / tinned electrolytic annealed copper conductor. Solid, stranded or flexible confirming to BS 6360 and IS 8130. Refer Table 1 for details.

Insulation :

PVC or HR PVC insulation in accordance with IS 5831. Polyethylene insulation in accordance with BS 6234 / IS 6474.

Twisting and Laying :

Required numbers of cores are laid up in case of multicore core cables. Individual pairs, triads or quads are formed by uniformly twisting the insulated cores with short lay lengths, prior to laying.

Core Identification :

Cores can be colour coded or number printed for easy identification. In case of multi pair cables one core in each pair is number printed in words as well as in figures at short intervals of 50mm or a numbered polyester tape is provided over each pair.

Overall Screen :

After final lay up of the complete cable an overall screen of aluminium-polyester tape is applied along with 0.5 sqmm multi stranded annealed tinned copper (ATC) drain wire in continuous electrical contact with aluminium side of the tape. Tinned copper braid screening can also be provided.

Individual & Overall Screen :

Individual pairs, triads or quads are screened by aluminium-polyester tape along with 0.5 sqmm ATC drain wire and overall screened by aluminium-polyester tape as mentioned above. Tinned copper braid screening can also be provided.In case of individually screened cables for critical applications an extruded isolation sheath can also be provided over the individual screens.

Assembly Binder :

After final assembly a non-hygroscopic polyester tape is provided to act as a binder as well as a bedding for the outer screening in all cables.

Armour:

Galvanized steel round wire or strip armour in accordance with BS 5308 / IS 1554 respectively. The armour wire and strip confirms to IS 3975. If required, G.I square interlock armour or G.I / S.S wire braid armour can also be provided.

Inner & Outer Sheath :

PVC, HR, FRLS PVC or ZHLSF sheath in accordance with IS 5831 can be provided. U.V stabilized Polyethylene sheath can also be provided for hazardous areas. A blue colour outer sheath for intrinsically safe areas can be provided on request. A pair of communication wires can be provided if desired.

This conductor is made from aluminium-magnesium-silicon alloy of high electrical conductivity containing enough magnesium silicide to give it better mechanical properties after treatment. These conductors are generally made out of aluminium alloy 6201. AAAC CONDUCTOR has a better corrosion resistance and better strength to weight ratio and improved electrical conductivity than ACSR CONDUCTOR on equal diameter basis.

AAC conductor is made from aluminum-magnesium-silicon alloy of high electrical conductivity containing magnesium (0.6-0.9%) & silicon (0.5-0.9%) to give it better mechanical properties after treatment. AAC conductors are generally made out of aluminum alloy 6201 (minimum conductivity is 54%). AAC conductor has a better corrosion resistance and better strength to weight ratio and improved electrical conductivity than ACSR conductor on equal diameter basis.

Key Benefits:

• High tensile strength as compared to AAC conductor.
• Higher conductivity as compared to ACSR conductor.
• Better corrosion resistance than ACSR conductor.

Physical contents of alluminium alloy :

• Density - 2.70 kgm/dm3 at 20C
• Coefficient of Linear Expansion - 23 x 10-6 / C
• Resistivity - 0.0326 Ohms mm2/m at 20C
• Constant Mass Temperature Coefficient (a) - 0.00360/ C
• Material - Heat treated Al. Mg. Si. Alloy