Bry-Air (Asia) Pvt. Ltd.

Sector 18, Gurugram, Haryana

Ethylene removal is a natural process that does not affect the property of fruit or vegetable. Ethylene that is released naturally can be continuously removed by Bry-Air Ethylene Scrubber (BES) through the process of adsorption and chemisorption.Bry-Air Ethylene Scrubber (BES) extends shelf life of fruits and vegetables, minimizes loss due to decay, ensures off season availability and eliminates harmful preservation practices that use Nitrogen and Sulphur gas. Fruits and vegetables, thus retain their naturalness and can be ripened as per demand without bearing traces of toxic gases.

How Bry-Air Ethylene Scrubber (BES) removes Ethylene?

Ethylene is slightly heavier than air. When it is placed in airflow on the floor in a closed system, it sucks air from its lower ducts and passes it through the specially designed Honeycomb Matrix chemical filter where it immediately neutralizes Ethylene chemically and release clean air outside containing no bad effects on fruits and vegetables. Bry-Air’s new Honeycomb Matrix based macro porous chemical filters are metal silicates impregnated with Potassium Permanganate (KMnO4). Potassium permanganate is an oxidizer that reacts with Ethylene in the air and releases CO2 and Water.

Few Advantages of Bry-Air Ethylene Scrubber Comprising of Honeycomb Chemical Filter:

• Energy saving because of very low pressure drop
• Low footprint
• Filter Cassettes can be replaced with ease without any expertise
• Robust CNC fabricated construction, painted unit
• Kills bacteria, pathogens and viruses from air

Ethylene Control is a must for all passive cold stores, storing perishable fruits and vegetables for long duration. For example :

• Apple storage
• Potato storage for potato chips
• Potato storage for seed
• Tomato seed storage
• Onion storage

Bry-Air setting new benchmarks in gas phase filtration have introduced a custom-designed solution for data centres known as Bry-Air DataCenter Air Purifier (DAP). With the introduction of Bry-Air DataCenter Air Purifier (DAP), you can now protect your data center effectively from threat of electronic corrosion and abrupt failures. Bry-Air DAP is manufactured to the highest quality, reliability and ecological standards.

Bry-Air DAP houses a revolutionary Honeycomb Chemical Filter which is the heart of the system. This next generation revolutionary new medium is a building block of our new custom designed solution for data centers. Bry-Air macro-porous desiccant formed honeycomb matrix filter has a high bulk density and very high structural strength as well as adsorption capacity. This honeycomb matrix technology not only reduces the size of DAP but also increases its efficiency and life while reducing energy bills. All this provides a much higher capacity chemical filter with a much longer mean time between replacements (MTBR).

Some of the Salient Features of Honeycomb based Bry-Air DataCenter Air Purifier (DAP)

• Only honeycomb filter with permanganate
• Ease in replacement of media filter
• Optimum space stilization
• Ease of operations/maintenance
• Very high impregnation of oxidizing agent, resulting in 100% desired output
• Filters cassettes are made of stainless steel (SS)
• Filters are tested in accordance with the standards of ASHRAE 145.2 and ISO 11155-2
• Energy saving because of very low pressure drop over traditional media
• Bry-Air air purification honeycomb bed recirculation/pressurization units (GPF) are the self-contained units
• Bry-Air purification system removes both organic and inorganic contaminants from the air and supplies air free of contaminant gases to the controlled environment
• Robust CNC fabricated structural construction & painted unit

Easy to operate

• Suitable for continuous operation
• Manual switch for operating the system
• Easy to handle due to low weight

Easy to install

• Versatile, easy to package and handle

Small footprint, low volume / weight per CMH

Easy to maintain

• Quick and easy to service
• Easy honeycomb media replacement
• Easy, tool free access to all major components
• Quick serviceability and maintenance free operation

“Enviroliner”, as it is popularly known, is the ideal solution to Humidity related storage problems. It is a humidity controlled mobile housing for safe storage of small equipment like engines, gear boxes, small arms, ammunition, optics, ration, documents, Enviroliners are customised modular PVC store house which can convert any space in whole or in part into cost effective humidity controlled storage area. There are no special infrastructural needs except for a “floor and a “ceiling”. Equipment and material stored in Enviroliners are protected against damaging effects of moisture – rust, mold & fungus. iform, etc, prevents corrosion.

Enviroliners are custom made using flexible special grade thermo plastic barrier material to ‘build’ the walls on a framework and ‘zipped’ closed. A small, desiccant dehumidifier controls the relative humidity to the required level – 35% to 50% RH – to ensure humidity controlled conditions needed for safe storage.

• Ceiling suspended
• Free standing on framework
• Around existing storage racks
• Panels or walls can be of transparent or translucent material to take advantage of existing lighting
• Provision for lighting internal area

• Doors can be fitted to suit individual need e.g. personnel access, fork lift access etc.

Flexible Barrier Storage (FBS) Systems are employed and adopted by the Army, Navy and Air force all over the world for preservation of hardware equipment and storage of active-status material.

The Flexible Barrier, or the Flexible Storage (FBS) Systems consist of a reusable cover, which is resistant to moisture, oil, bacteria, insects, rodents, etc., a humidity sensing device and a chemical desiccant dehumidifier.

This system of preservation is very versatile, more practical and technically superior to any other system of preservation in the world. It assures flexibility and mobility in choice of storage sites and eliminates the need for storage sheds; reduces manpower costs and is easy to maintain even by unskilled personnel.

The high degree of preservation achieved through the dehumidification system enables rapid reactivation of the defence equipment. Being mobile, it can move with the troops and can be installed on site whenever required, on any terrain.

The FBS system protects military equipment from corrosion as well as from the effects of humidity, salt, pollutants, dust and insects. It also protects equipment from effects of ultra-violet rays of the sun on metal, rubber, paint, canvas, etc. Damages caused by micro-organisms such as fungi and molds is avoided.

Environmental protection also increases MTBF (Mean Time Between Failures) of the equipment - whatever its size and sophistication - from the smallest piece of electronics to modern computer-guided bomber aircrafts and armored fighting vehicles (AFVs), from batteries to radars and missiles.

Shrouding of aircraft, helicopters and missiles using the FBS protects them from the damaging effects of moisture, dust and ultra-violet rays.

The Bry Air Conveying system advantage is in it being a one-stop shop. This ensures no spillage, no material wastage, right material for the right machine at the right time and quick change over of material. This results in continuous feed of material and thus an accident free shop floor.

• Receiver
• Regenerative Vacuum Pump Station
• Central Dust Collector
• Bry Smart Controller

All the parts in contact with material is made of SS304.

The Integrated Proximity Sensor activates material demand. The special dump valve design mounted on a bearing allows smooth movement of dump valve’s blanking disc and closing during the conveying process.

The SS Mesh Filter of 530 micron separates the resin from the air. There is a Vacuum Break Valve for automated mesh filter cleaning and quick evacuation. Specially designed material entry creates ‘cyclonic effect’ to save filter mesh from damage.

The special flapper with a long life silicone seals at mesh filter, load valve and dump valve for leak proof vacuum. This allows receiver usage at higher temperatures.

The special flapper also served the purpose of deflecting incoming material away from the screen.

The Access Door allows servicing & inspection of dump valve assembly without any tools. The receiver comes with a highly effective magnet and a clearly visible tower light for status of operation and fault. The Receiver comes in capacity options of 6/15/30/60 and 75 liters.

The brushless regenerative pumps are noiseless and low in maintenance. They provide powerful vacuum to convey free flowing pellets and regrind.

Every unit is fully assembled and permanently lubricated to deliver optimum vacuum and is consolidated on a compact frame.

The optional discharge selection valve allows exhaust air to be recycled back to the closed loop dry air system, or discharged to the atmosphere.

Specially designed by-pass valve with silencer, which allows pump to run on past system demand for prevention of rapid start/ stop cycles and pump over heating.

Safety relief valve and vacuum gauge to provide safety to the pump during certain unavoidable circumstances.

State-of-the art microprocessor controlled pump safety system which indicates voltage, current, frequency, load bar graph and a fault display of over load, under voltage, over voltage, phase sequence reversal & failure.

A CRC powder Coated Self Standing Chamber that can be located anywhere between the pump and conveying system.

The central dust collector protects the pump and reduces filter maintenance by collecting fines and dust.

The separated dust and fines collected are easily cleaned and the sight glass in the chamber provides view for inspection.

Touch Screen Color Display & Management Password Protected Data Entry System.

Independent controller for each receiver. Clear functional colour display of each receiver and regenerative vacuum pump station.

Possible to program load time, dump time and regrind in % conveying time with respect to source in case of usage of Vacuum take off box(p) & Regenerative Vaccum Pump Station Seek Time.

Audio Visual warning alarm with message that conveys shortage, material not conveyed for long, receiver waiting for material and regenerative vacuum power unit tripped.

RVPS Isolator switch off and emergency switch off. Alert message for cleaning the filter. The occurrence of it is programmable.

Bry-Air, the leaders in Dehumidification … worldwide, is a global solution provider having over 50 years of experience in air treatment and dehumidification. It has strong presence in the Indian sub-continent and is the leading state-of-the-art manufacturer of Gas Phase Filtration (GPF) Systems in India since last 15 years and known for setting new benchmarks. The strong research & developmentand testing facilities located at the GPF lab in Gurgaon are testimonial to the continuous growth and success.

Based on this legacy across the globe and country and intrinsic R&D strength, BRY-Air is proud to introduce yet another revolutionizing product solution, Atmospheric Corrosivity Monitor (ACM), which will enable measure corrosion with ease and accuracy in the environment.

Environment with higher atmospheric and air contamination require greater attention to air quality management. The interactive result of temperature variations and humidity with the gaseous contaminants has the potential to increase the threat of air corrosion, providing greater reasons for close monitoring of the immediate environment of IT infrastructure. All companies dealing with sensitive IT infrastructure, as a core part of its operations, need to implement a comprehensive checking and monitoring mechanism for the corrosion potential of the gases inside their facility. The ISA standards define or characterize environments in terms of their overall corrosion potential.

Bry-Air Atmospheric Corrosivity Monitor (ACM) diagnoses the corrosion of these environment according to the ISA Standard 71.04-2013 outlining severity of corrosion from G1 (mild) to GX (severe) environment. Reactivity monitoring can be used to characterise the destructive potential of an environment. Measurement of thickness of corrosion film provides an excellent indication of the type(s) and level(s) of all corrosive gases present in the local environment.

Air Borne Contamination is an undesirable by-product of the changing lifestyles of mankind. Greater demand for more efficient products and services has led to rapid industrialization, which in turn has put excessive pressure on the environment into accepting higher than safe levels of pollutants that it can safely eliminate.

Atmospheric air, especially in manufacturing industry, is laden with gaseous chemicals of the likes of hydrogen sulphide, sulphur dioxide, nitrogen oxides, chlorine, ammonia, mercaptans, hydrocarbons etc. Needless to say, these are generated during the manufacturing processes, and eventually mix with the surrounding air. Common examples are fuel combustion related by products, gases generated during complex chemical processes, automotive fumes, etc. Other than the problem of ‘outside’ impure air, in many cases, such as in enclosed commercial establishments, contaminants are generated either from or within the space, eg. tobacco smoke, formaldehyde and other organic compounds from paint and furnishings, food smells etc.

Bry-Air Ecoscrub Gas Phase Filtration system is the ideal and most cost-effective solution for Air Borne Contamination. It’s unique process not only cleans the contaminated air of suspended particles and corrosive gases but is also used for odor removal, making the working environment healthy for you and your electronic equipments.

Gas Phase Filtration Application Areas, it is ideal for industries as diverse as :

• Data Centers
• IT / Server rooms,
• Petroleum and Oil refineries,
• Food Processing Plants,
• Paper and Pulp,
• Waste Water and Sewage treatment facilities
• Museums and Libraries,
• Post Harvest Storage Facilities
• Iron & Steel
• Semiconductor

How does gas phase filtration system work ?

The process of gas phase filtration is simple. The contaminated air first passes through pre-filters which trap the suspended particles, and then through the required chemical media beds, which chemically destroy or retain any remaining gaseous impurities. The chemical media can be activated carbon and / or activated alumina impregnated with proprietary chemicals, used alone or in combination – depending on the types and concentrations of the impurities present in air stream.

Ecoscrub Systems are designed to operate and maintain contaminant gas levels at 1 ppb (parts per billion) or less.

The Bry-Air EcoBlend BVD Series Volumetric Dosers are designed and engineered for dosing continuously as well as intermittently of (upto) 4 types of material in granule form.

BVD Series Volumetric Dosers assure thorough and accurate dosing of virgin material, regrind material, additives, fillers, and master batches.

• Microprocessor controlled LED indicator for operating status and fault
• Digital display of set point of speed and time
• Quick openable latches for motor and screw removal
• Drain cover for quick batch change and clean out
• Sight glass to check on material level

• Compact and accurate DC geared motor

• PTC heaters for Victory series 200, 300 and 600 models
• Microprocessor based controller for monitoring
• RS 232/RS 485/Ethernet serial interface
• Remote ON/OFF facility

The Bry-Air Victory series dehumidifier is a non-cyclic, rotary type dehumidifier which dries air by continuous physical adsorption process, the simplest and most direct method of humidity control. TM The desiccant used by Bry-Air Victory series is non toxic, non flammable with maximum moisture removal capacity.

The moisture is adsorbed in the dehumidification sector by the slowly rotating fluted, metal silicate desiccant synthesized rotor and is exhausted in the reactivation sector by hot air stream in counter flow. Following the reactivation process, the adsorption sector is again ready to adsorb the moisture. Thus, the two processes of “moisture adsorption” and “reactivation” takes place simultaneously with separate airflow. Positive sealing between chambers prevents mixing of the process and reactivation air stream.

• Non-toxic, non-flammable, fully water washable adsorbent
• In-situ synthesized metal silicate desiccant on an inert, organic fibre substrate
• Active desiccant constituting 80% of the media weight, ensuring high performance and minimal heat carry-over
• Non-flammable rotor
• Net organic percentage in honeycomb media <2%
• Special edge hardened media surface ensuring a smooth surface and long life of both, media and the seal contacting it
• Rotor perimeter flange extends media and seal life
• Rotor incorporating robust internal structure with perimeter flange for industrial quality, durability and easy serviceability

Bry-Air has wide range of proprietary chemical media for Gas Phase Filtration to eliminate corrosive, odorous and toxic gases from Industrial and Commercial environment.

BRYSORB™ series offers range of combination of Activated Carbon and Activated Alumina impregnated with various impregnates which neutralizes various gaseous contaminant such as H2S, SO2, Cl2 and NH3, and widely used for gas phase filtration.

BRYSORB™  508 granular media is an Activated Alumina impregnated with Potassium Permanganate (KMnO4).

BRYSORB™ 508 chemical media is used to remove a variety of contaminant gases from air in hostile industrial environment such as Hydrogen Sulphide (H2S), Sulphur Dioxide (SO2), Sulphur Trioxide (SO3), Nitric Acid (HNO3), Formaldehyde (CH2O) Ethylene (C2H) and Aldehydes (-CHO).

BRYSORB™ 508 blend granular media is an Activated Alumina impregnated with Potassium Permagnate and other proprietary chemicals (KMnO4).

A perfect blend of  BRYSORB™ 508 and BRYSORB™ 520 for optimum removal of harmful and odourous gases such as Ozone(O3), Hydrogen Flouride (HF) and various other VOCs.

BRYSORB™ 515 granular media is an Activated Alumina and Activated Carbon impregnated with Potassium Hydroxide (KOH) for effective removal of Chlorine (Cl2) and Sulphides (SOx).

BRYSORB™ 515 chemical media is basically lowering or raising of the pH to a neutral condition with a change of state from a gas to a solid, stable salt. This is good to remove gases such as Hydrogen Sulphide (H2S), Sulphur Dioxide (SO2) and Chlorine (Cl2).

BRYSORB™ 520 granular media is pure Activated Carbon. This is neutral in nature.

BRYSORB™ 520 is the media in which one substance gets attracted and adheres to the surface of another. Atoms & molecules are held to gather in a solid by physical forces, as strong as vakence (chemical) bond and as week as Van-er-Waal’s (physical) attractive forces. This remove toxic gases such as Chlorine (Cl2), Nitrogen Oxide (NO), Carbon Disulphide (CS2), Toluene (C7H8), Isopropylalcohol (C3H8O) and trichloroethene (C2HCl3).

BRYSORB™ 525 granular media consist of cylindrical, porous pellets formed by combination of Activated Carbon impregnated with Phosphoric Acid (H3PO4) for effective removal of Ammonia (NH3).

Bry-Air offers latest technology in gaseous adsorption – Gas Phase Activated Carbon process which greatly increases the adsorption capacities of Activated Carbon. The Phosphoric Acid (H3PO4) impregnation is done in such a way to ensure uniform distribution across the entire volume of pellet so that the target gas will react with chemical media.

The chemical media used in chemical filter is consumable and cannot be regenerated Therefore it has to be replaced whenever consumed. Determining the time of replacement is important so that media is not replaced when its life is left or we keep on using the system once the chemicals are consumed also.

Bry-Air has in-house lab to ensure that the media is checked at regular interval and changed at appropriate time. Bry-Air provides you the facility to check the “life” of chemical media free of cost. Just send us the sample of the chemical media to us and we will let you know the life of chemical media.

Bry-Air, achieved a yet another breakthrough benchmark in its ‘in-situ’ synthesized macro porous Honeycomb technology research by extending it to Gas Phase Filtration. In a chemical filter, gases are filtered and cleaned out when they are passed through a chemical filter. Bry-Air’s new macro porous honeycomb matrix based chemical filter provides largest amount of chemical for chemisorption and can neutralize even ultra low concentration of gaseous contaminants. This new technology will remove contaminants from air supply stream, comprising of gases, odor elements or volatile organic compounds more efficiently and effectively.

Fluted Media Chemical Filters

This is a superior technology as compared to granular packed bed filter. A macro porous desiccant based Honeycomb Matrix comprising of a flat and corrugated sheet of Active Desiccant. The substrate is of inorganic fiber media. It has high efficiency and reliability. This is designed for higher airflow therefore requires lower face area and has lower pressure drop. This also eliminates the requirement of after filter

Fluted Media Chemical Filter has high “%” impregnation of Potassium Permangnate (typical 15 % of KMNO4)

Advantages of DRISORBTM Honeycomb Chemical Filters

• Bulk Density > 20 lbs/cu.ft
• Honeycomb Monolith Media Available in 1” to 12” Depths in Standard and Custom Filter Sizes
• Air Flow Range is 400 to 600 FPM
• Tested by Most Respectable RTI Lab of USA
• Longer Life (Higher MTBR)
• Tested in Accordance to ASHRAE 145.2P and ISO 11155-2
• Only Honeycomb Filter with Permanganate
• Very High Capacity
• Very Low Pressure Drop
• Available in Combination with Various Impregnants
• Backed by Bry-Air’s Cutting Edge State-of-the-Art R&D and Testing Facilities

Honeycomb Chemical filter can be used in wide range of industries

The new honeycomb matrix technology can be used both in commercial and industrial applications and is ideal for human and hardware health. It removes contaminants, eliminates odor and reduces downtime by removing toxic/corrosive gases through the process of chemisorption making it ideal for gas phase filtration in:

• Paper and Pulp Industry
• Petrochemical Refineries
• Waste Water Treatment
• Data Centers and Mission Critical Facilities
• Process Industry
• Server Rooms
• Research Labs
• Electronic and Semi Conductor Industry
• Food Processing Industry
• Fertilizer Industry

Introducing the Adsorption Chiller, based on an innovative green technology, and the first of its kind in India. A lot of low grade process heat (50°C – 100°C) generally goes waste because of the technology gap to utilize it effectively. Bry-Air has launched a futuristic product, using advanced green technology, which can now use this low grade waste heat for cooling without any environmental damage. It is a first ever product being launched in India to tap the abundant low grade waste heat available in process industries and use it for process cooling or air-conditioning (HVAC). This eco-friendly solution cuts down CO2 emission and reduces energy expenses.

The Bry-Air Adsorption Chiller is based on an advanced green technology using inert Silica Gel (adsorbent) and Water (refrigerant) pair. It has unbeatable advantages like ultra-low electricity consumption, negligible noise and vibration, life expectancy of more than 25 years, negligible maintenance, etc. It is ideal for industries like Power,  Food & Beverages,  Pulp and Paper, Solar, Chemical manufacturers, etc. and for Commercial areas like Offices, Buildings, Hotels, Malls,  etc. 

Bry-Airs BryXchange is an air to air rotary heat exchanger which recovers energy from high temperature exhaust air. Considerable high temperature air is generated in kilns, ovens, furnaces etc which generally goes waste. Through BryExchange this sensible waste energy can be recovered from the exhaust air and transferred to the low temperature supply air with efficiency of upto 75% energy.

Principle of working for BryXchange Air to Air Rotary Heat Exchanger

BryXchange rotor is installed between the high temperature exhaust air and supply air stream. As the rotor slowly rotates, sensible heat of temperature exhaust air is carried over by the rotor to the low temperature supply air.

Design and Structure of BryXchange Air to Air Rotary Heat Exchanger

The BryXchange rotor has a fluted media, fabricated with material having a high heat carrying capacity, which rotates between two side-by-side ducts: on a low temperature supply air duct, the other a hot temperature exhaust air duct. The axis of the rotor is located parallel to, and on the partition between, the two ducts.

BryXchange Air to Air Rotary Heat Exchanger's Advantage

• Higher energy recovery
• Lower electric energy costs
• Compact unit design results in less weight
• Temperature control
• Considerable primary fuel saved

High efficiency and reliability

• Stainless steel, double walled, insulated casing
• Sectorized Wheel for ease of installation and maintenance
• Designed for very slow rotational speed of around 8-10 RPM
• Manual cleaning system for media cleaning
• Heat-stabilised external bearings with teflon gasket
• Smooth surface to ensure minimum vertical runout
• The rotor is made of alternate flat and corrogated foil of very uniform pitch and height
• Rotor depth 200mm
• Substrate-Aluminised steel or Stainless Steel foil
• Split casing for larger sizes

The Bry-Air EcoMove BVL Series automatic Vacuum Loaders offer large savings to plastics processors, both in terms of man-hours and material by automating the transfer of plastic pellets from shipping containers and storage bins to the processing machines. Engineered for noiseless operation with sleek and easy to handle floor mounted blower console with efficient filters and controls, the BVL series Auto Loaders allow no leakage and are easy to maintain. The compact design ensures that there is no wear and tear and thus needing minimum maintenance.

Ratio loading for resin available and regrind magnetic grills for removal of ferrous impurities. Technical specification available for twin loader click here.

• Noiseless operations
• Floor mounted blower console with efficient filters and controls, LED display for ease of operation*
• No leakage
• No wear and tear
• Easily removable receiver for cleaning, less and easy maintenance
• Timer-based automatic control for loading sequence, auto start and stop of loading sequence
• State-of-the-art clear acrylic/polycarbonate receivers/belleys, clear view of material
• Transparent flexible anti-static pipe for conveying material (Optional)
• High quality easily removable filters

The Bry-Air offer superior quality Mould Temperature Controller BTC series which is designed to maintain constant temperature of Mould during the Moulding process. It is engineered to provide precise temperature control.

This technology is increasingly being used to improve the quality of injection moulded parts and to avoid material wastage during injection moulding start up phase.

Apart from its functioning it has an exquisite appearance and is small in size, also it is convenient for mobility as the unit is mounted on wheels.

Widely demanded in various industries, our range is known for its reliability & accuracy. We provide these in different specifications to meet the diverse demand of customers in different Industries with different application areas worldwide.

The state-of-the-art design of our Mould Temperature Controller is seen in high quality injection plastic mould like automobile Industry, medical plastic industry, white goods industry etc.

Bry Air Mould Temperature Controller is available in water and oil.The temperature can be maintained between 40 – 90°C in case of water and 40-150°C in case of oil.

• Simple & compact design
• Suitable for all kinds of mould for Injection Moulding Machine
• Precise temperature control
• Easy connection for supply & return cooling circuit, by hose nipple

Bry-Air Odour Control unit provides a fresh, clean and odour free environment for human beings. Regular air purifiers can trap common contaminants like dust, pollen and other particulate pollutants. However, Bry-Air Odour Control Unit not only removes particulate pollutants but also effectively and efficiently scrub gaseous pollutants which cause odour and indoor air quality problems. It is successfully eliminating odorous gases from animal research labs, mortuary, sewage pumping stations and other places having a foul smell due to gases released by chemicals used in various processes.

• A self-contained unit
• Standard variants available in 850-3400 CMH (500-2000 CFM)
• Easy to replace media filter/cassette
• Filter cassettes are made up of stainless steel (SS)
• Energy saving due to low-pressure drop
• Filters tested against the ASHRAE 145.2 and ISO 11155-2 stnd.
• Suitable for 125-180 m/sec (400-600 FPM) usages
• Only honeycomb filter with potassium permanganate (KMnO4) impregnation
• Can be customised as per requirement

High performance plastics require precision and accuracy in all phases of production. Even the slightest deviation from the prescribed ratio of materials leads to products that are unusable and thus further leads to huge overhead expenses.

Gravimetric Blending Units solve this problem by automatically weighing multiple components to produce the exact blend of materials necessary to create a high-quality product every time with consistency. A Gravimetric Blending Unit is essential to get the most out of blow moulding, plastics extrusion, and injection molding processes.

Industrial Blender (Gravimetric Blending Unit) can be deployed in a variety of ways depending on the type of manufacturing process. Most can be mounted directly on other machines in order to create a seamless production process.

Also, Loaders are often a desirable peripheral for blenders in order to facilitate the loading process and avoid human error or injury.

In any industrial plastics environment, gravimetric blenders are an absolutely essential component of the production process. Their efficiency and easy use facilitate production without rejection, reduce human error and injury, and saves material.

Bry-Air’s Gravimetric Blending Units ensures proper mixing of additives and colours of the pellets or blends hence reducing rejections.

The Unit helps in providing the extruder /moulder with the most accurate solution of colours and blend of pellets, resins and master batches with consistency.

The Units can be used as a centralised stand-alone system or it can be machine mounted.

The throughput ranges from 6.8 kg/hr to more than 2268 kg/hr. All models dispense and blend all materials (in granular form) for continuous and unfailing accuracy.

• Accurately weighs ingredient and virtually eliminates colorant and additives getting wasted
• Consistent Accuracy
• Automatically adjust for variations in density
• Calibration is an automatic in function
• Setup in minutes not hours
• Measures by weight not volume