Balaji Group of Industries

Kotharia, Rajkot, Gujarat

Features

• Reduced Or Full Port
• Lift Or Swing Chek Valve
• Spiral Wound Gasket Of Stainless Steel
• Bolted Cap
• Socket Weld Or Threaded Ends
• Replaceable Or Integral Hardfaced Seat

Applicable Stabdards

• Basic Design, MS-SP-118 & Ansi B16.34
• Socket-Weld (S.W) Ansi B16.11
• Threaded End (S.E) Ansi B1.20.1
• Valve Test And Inspect :API 598
• Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F316L.

Features:

• Investment Casting
• SS 140 304 316

Availabe Sizes:

• 1/2 3/4 1

TYPICAL APPLICATIONS

DRIP, TRACER:The FS600 Thermodynamic stream trap is commonly used as a drip trap on steam mains and steam supply lines. Supplied with integral Strainer and these traps can be used on tracing applications; however, thermostatic traps are normally recommended for this service. Ideal for outdoor application that Are subject to freezing and for superheated steam conditions

HOW IT WORKS

The thermodynamic trap has cyclic on-off operation with a disc that is pushed open by incoming condensate and closes lightly when steam tries to escape.

FEATURE

• Integral strainer protect trap from contamination
• Hi pressure applications up to 600 PSIG
• Hardened stainless steel seat and disc for extended service life even at high pressure
• Singltrap will operate over the entire pressure range of 3.5-600 PSIG [Not recommended for use below 10 PSI]
• Suitable for superheated steam
• Freeze proof when trap is piped in a vertical orientation for complete drainage of condensate
• Tree-hole balanced discharge extends life of the seat area
• Trap will function in any orientation (horizontal preferred)

SAMPLE SPECIFICATION

The steam trap shall be all stainless steel thermodynamic type with hardened integral seat and disc with integral strainer.

INSTALLATION

Trap can be installed in any position; however horizontal is preferred. Installation should include isolation valves. Do not weld or damage can occur to the seat area.

MAINTENANCE

If trap fails, close isolation valves and remove cap. clean disc and seating surfaces and replace cap and disc with grove side toward seat.

Features

• Reduced Or Full Port
• Compact Outside Screw & Yoke
• Spiral Wound Gasket Of Stainless Steel
• Bolted Bonnet or Welted Bonnet
• Socket Weld Or Threaded Ends
• Integral Hardfaced Seat

Applicable Stabdards

• Basic Design, BS 5352 & Ansi B16.34
• Socket-Weld (S.W) Ansi B16.11
• Threaded End (S.E) Ansi B1.20.1
• Valve Test And Inspect :API 598
• Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F316L.

Features

• Reduced Or Full Port
• Compact Outside Screw & Yoke
• Spiral Wound Gasket Of Stainless Steel
• Bolted Bonnet or Welded Bonnet
• Socket Weld Or Threaded Ends
• Replaceable Hardfaced Seats

Applicable Stabdards

• Basic Design, BS 5352 & Ansi B16.34
• Socket-Weld (S.W) Ansi B16.11
• Threaded End (S.E) Ansi B1.20.1
• Valve Test And Inspect :API 598
• Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F316L.

We are offering forge globe valve. Features : reduced or full portcompact outside screw & yokespiral wound gasket of stainless steelbolted bonnet or welted bonnetsocket weld or threaded endsintegral hardfaced seatapplicable stabdards : basic design, bs 5352 & ansi b16.34socket-weld (s.w) ansi b16.11threaded end (s.e) ansi b1.20.1valve test and inspect :api 598standard material: a105n, lf2, f5, f11, f22, f304, f304l, f316, f316l.

We are offering forged gate valve, features : reduced or full portcompact outside screw & yokespiral wound gasket of stainless steelbolted bonnet or welded bonnetsocket weld or threaded endsreplaceable hardfaced seatsapplicable stabdards : basic design, bs 5352 & ansi b16.34socket-weld (s.w) ansi b16.11threaded end (s.e) ansi b1.20.1valve test and inspect :api 598standard material: a105n, lf2, f5, f11, f22, f304, f304l, f316, f316l.

Salient features of spring loaded disc type non return valve: investment casting body constructioncompact & rugged designstronger, liter and smaller than conventional swing check valve, hence less expensive to install and maintainsingle disc typespring loaded disc to prevent reverse flow in pipe lineeasy to installation between two pipe flangesmetal to metal or soft seat optionmaintenance free designzero leakage (in soft seat)full port openingless pressure dropwafer, flangeless, sandwich typeshorter length, required minimum spaceoffer any 3rd party or client inspection.

We are offering forg check valve, horizontal check valve lift check valve - class 800 forged steel check valvefeatures : reduced or full portlift or swing chek valvespiral wound gasket of stainless steelbolted capsocket weld or threaded endsreplaceable or integral hardfaced seatapplicable stabdards : basic design, ms-sp-118 & ansi b16.34socket-weld (s.w) ansi b16.11threaded end (s.e) ansi b1.20.1valve test and inspect :api 598standard material: a105n, lf2, f5, f11, f22, f304, f304l, f316, f316l.

Features

• Bolted Bonnet Or Welded Bonnet
• Spiral Wound Gasket Of Stainless Steel
• Integral Hardfaced Seat
• Compact Outside Screw & Yoke
• Applicable Stabdards
  • Basic Design BS 5352 & Ansi B16.34
  • Face To Face Ansi Inspect :API 598
  • Flanged End (F.E) Ansi B16.5
  • Valve Test And Inspect :API 598
  • Standard Material: A105N, LF2, F5, F11, F22, F304, F304L, F316, F304L