Bagadia Petrochem

Andheri East, Mumbai, Maharashtra

Description

Luban HP2100N is manufactured using Novolen vertical stirred Gas-phase polymerization process. Luban HP2100N is a homopolymer polypropylene injection molding grade. The grade exhibits good flow and stiffness.

Application

General injection molding, closures, furniture, houseware.

Processing Guidlines

The Typical Processing Conditions for Luban HP2100N are:

Melt temperature 220 – 260 °C

Holding pressure 200 – 500 bar Maximum to avoid sink marks

Storage and Handling

Luban HP2100N must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material

Safety

Luban HP2100N is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet

Food Contact

Luban HP2100N meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration”.

Mold temperature 20 – 40 °C

Injection speed High

Shrinkage 1 – 2 % depending on wall thickness and molding parameters

Note: Processing parameters should only be used as guidelines. The above properties values are not to be construed as specifications

DESCRIPTION

RJ768MO is a high MFR transparent polypropylene random ethylene copolymer based on proprietary Borstar Nucleation Technology (BNT), with an excellent organoleptic performance, Additivation has been enhanced to provide good antistatic properties, without blooming or plate-out, and with optimized molecular weight distribution giving low warpage. Products produced from this product have excellent transparency, gloss and fast crystallization speed which offers high productivity in production of transparent food packaging products.

RJ768MO is designed for high-speed injection moulding and contains nucleating and de-moulding additives.

APPLICATIONS

• Food Packaging
• Transparent thin wall containers
• Lids
• Houseware articles
• Media packaging

SPECIAL FEATURES

• Excellent organoleptic properties
• Good stiffness and impact balance
• Very good transparency
• High melt flow
• Sustainability solutions compatible

PROCESSING CONDITIONS

• RJ768MO is easy to process with standard injection moulding machines
• Following parameters should be used as guidelines:
• Melt temperature: 220 - 250°C
• Holding pressure: 200 - 500bar As required to avoid sink marks.
• Mould temperature: 15 - 40°C
• Injection speed: As high as possible
• Shrinkage 1 - 2%, depending on wall thickness and moulding parameters

STORAGE

RJ768MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product.

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

RECYCLING

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling

DESCRIPTION

SABIC PP 520L is specially developed for tubular water quenched blown film applications with suitable dosage of slip and antiblock additives. Films produced using SABIC PP 520L has the following features: Consistent processability; High melt strength; Good optical properties; Excellent runability on bagging and sealing machines.

TYPICAL APPLICATIONS

SABIC® PP 520L can be used for producing garment packaging, textiles packaging, magazine covers and for food packaging.

PROCESSING CONDITIONS

• Typical processing conditions for PP520L are:
• Average extrusion temperature range may be kept at 205 - 215°C.

HEALTH, SAFETY AND FOOD CONTACT REGULATIONS

Material Safety Data Sheets (MSDS) and Product Safety declarations are available on our Internet site http://www.SABIC.com. For additional specific nformation please contact SABIC local representative.

STORAGE AND HANDLING

Polypropylene resin should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably do not exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smel and inadequate product performance. It is advisable to process PP resin within 6 months after delivery

Product Description

Moplen HP552R is a polypropylene homopolymer suitable for extrusion applications. Moplen HP552R is formulated with an anti-gasfading stabilisation package. Moplen HP552R is used for the production of (bulk) continuous filaments and fine denier staple fibres. Typical applications are carpets and nonwovens.

This grade is not intended for medical and pharmaceutical applications.

Status Commercial: Active

Availability Africa-Middle East; Asia-Pacific; Europe

Application Absorption & Filtration; Bulk Continuous Filament & Continuous Filament; Filament Yarn; Hygiene Nonwoven; Nonwovens; Wipes/Tissues

Market Textile

Processing Method Continuous Filament/Spinning; Fibers; Spunbond; Staple Fiber

Attribute Gas-fading Resistant; High Flow; Homopolymer

Storage:

The resin is packed in 25 kg bags, octabins or bulk containers protecting it from contamination. If it is stored under certain conditions, i. e. if there are large fluctuations in ambient temperature and the atmospheric humidity is high, moisture may condense inside the packaging. Under these circumstances, it is recommended to dry the resin before use. Unfavorable storage conditions may also intensify the resin's slight characteristic odor.

Resin should be protected from direct sunlight, temperatures above 40°C and high atmospheric humidity during storage. Higher storage temperatures may reduce the storage time. The information submitted is based on our current knowledge and experience. In view of the many factors that may affect processing and application, these data do not relieve processors of the responsibility of carrying out their own tests and experiments; neither do they imply any legally binding assurance of certain properties or of suitability for a specific purpose. This information does not remove the obligation of the customer to inspect the material on arrival and notify us of any faults immediately. It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are observed.

Product Description

A Homopolymer resin desinged for spundbond nonwovens. The resin is particularly suited for excellent spinning for uniform, high quality fabrics. Formulated for applications requiling low color and low gas fading discoloration.

DESCRIPTION

BD265MO is a very high impact heterophasic copolymer based on proprietary Borstar Nucleation Technology (BNT). This product exhibits excellent impact strength even at low temperatures and good processability and stiffness properties Articles produced with this grade exhibit very good demoulding properties and dimensional consistency with respect to different colours.

APPLICATION

• Juvenile care
• Toys
• Crates, boxes and pallets
• Heavy duty pails
• Furniture Technical applications

SPECIAL FEATURES

• Very high impact strength
• Efficient processing with BNT
• Good demoulding
• Excellent dimensional stability

PROCESSING CONDITIONS

BD265MO is easy to process with standard injection moulding machines.

Following parameters should be used as guidelines:

Melt temperature: 220 - 260°C

Holding pressure: 200 - 500bar As required to avoid sink marks

Mould temperature: 10 - 40°C

Injection speed: As high as possible

Shrinkage 1 - 2%, depending on wall thickness and moulding parameters

STORAGE

BD265MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

RECYCLING

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

DESCRIPTION

BJ368MO is a heterophasic copolymer characterized by very high flow, and optimum combination of high stiffness and impact strength.

The material is nucleated with Borstar Nucleation Technology (BNT). Flow properties, nucleation and good stiffness give potential for cycle time reduction.

The material has both good antistatic performance and mould release properties

APPLICATIONS

• Thin wall containers
• Food packaging
• Small size ice cream containers

SPECIAL FEATURES

• Very good stiffness and impact balance
• Good flow behaviour
• Reduced cycle time and increased output

PROCESSING CONDITIONS

BJ368MO is easy to process with standard injection moulding machines.

Following parameters should be used as guidelines:

Melt temperature: 210 - 260°C

Holding pressure: 200 - 500bar As required to avoid sink marks

Mould temperature: 10 - 30°C

Injection speed: As high as possible

Shrinkage 1 - 2%, depending on wall thickness and moulding parameters

STORAGE

BJ368MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product.

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

RECYCLING

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

PRODUCT DESCRIPTION

HDPE B1054 is high density polyethylene specially developed for large blow molding and jerry cans. The material offers high stiffness, good processability and excellent combination of stiffness/ESCR.

TYPICAL APPLICATIONS

B1054 is specially designed for Standard jerry cans, Light weight jerry cans and UN approved jerry cans. The grade is intended for use in food contact application.

FOOD REGULATION

B1054 is suitable for Food contact application. Detailed information is provided in relevant Material Safety Datasheet and for additional specific: information please contact SABIC local representative for certificate

STORAGE AND HANDLING

Polyethylene material should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably don't exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PE resin within 6 months after delivery.

DESCRIPTION

SABIC® PP 5706P is specially developed for producing rigid injection molded articles for general purpose applications. It gives consistent processability and high gloss at the products.

TYPICAL APPLICATIONS

SABIC® PP 5706P can be used for houseware articles, food containers, furniture and toys.

PROCESSING CONDITIONS

• Typical processing conditions for 5706P are:
• Barrel temperature range: 200 - 250°C.
• Mold Shrinkage: 1.2 - 2.5% depending on wall thickness and processing conditions.
• Mold Temperature: Normally 15 - 40°C, up to 65°C for thick parts

STORAGE AND HANDLING

Polypropylene resin should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably do not exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PP resin within 6 months after delivery.

Description

Luban polypropylene is manufactured using Novolen vertical stirred Gas-phase polymerization process. Luban HP3104K is a homopolymer polypropylene, it is suitable for high speed metallisable Biaxially Oriented Polypropylene (BOPP) film.

Application

Core layer in BOPP film. Food and non-food packaging bags, plain and laminated garment bags, plain and pigmented label film, lamination film, plain overwrap film, plain and colored adhesive tapes.

Note: These are typical properties only and are not to be construed as specifications. Users should confirm results by their own tests.

• The Typical Processing Conditions for Luban HP3104K are:
• Extrusion Temperatures 200 – 250 °C
• Chill Roll Temperature 20 – 40 °C
• MD Stretching Temperature 130 – 160 °C
• MD Stretching Ratio 4 – 7
• TD Stretching Temperature 155 – 170 °C
• TD Stretching Ratio 7 – 10

Note: Processing parameters should only be used as guidelines. The above properties values are not to be construed as specifications.

Storage and Handling

Luban HP3104K must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material

Safety

Luban HP3104K is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet.

Food Contact

Luban HP3104K meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration”.

Recycling

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

DESCRIPTION

HG385MO is a polypropylene homopolymer intended for injection moulding. This product combines unique Borstar reactor design with Borstar Nucleation Technology (BNT) to produce highly crystalline polypropylene. This product is characterized by excellent flow properties combined with a narrow molecular weight distribution, well suited for low warpage products.

This product contains anti-static and slip additives, which result in short cycle time, easy demoulding and low dust attraction.

Products moulded from this grade exhibit excellent dimension consistency combined with high stiffness and gloss.

APPLICATIONS

• Caps and closures
• Appliances with great heat resistance
• Household articles

SPECIAL FEATURES

High stiffness Low warpage

Heat resistance High gloss

Shows excellent antistatic performance

HG385MO is easy to process with standard injection moulding machines.

Following parameters should be used as guidelines:

Melt temperature: 220 - 260°C

Holding pressure: 200 - 500bar As required to avoid sink marks

Mould temperature: 10 - 30°C

Injection speed: As high as possible

Shrinkage 1 - 2%, depending on wall thickness and moulding parameters

STORAGE

HG385MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

RECYCLING

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling

DESCRIPTION

RE420MO is a versatile designed transparent polypropylene random ethylene copolymer with medium melt flow rate intended for injection moulding and injection stretch blow moulding

RE420MO is suitable for high speed injection moulding due to clarification and excellent demoulding properties. Articles originating from this product have excellent transparency, good organoleptic properties, good balance of stiffness and impact strength at ambient and refrigerator temperatures, low blooming, good denesting performance and excellent hinge properties.

APPLICATIONS

• Lids
• Transparent pails
• Customized / hinged closures
• Food storage containers
• Sports and drinking bottles
• Houseware containers

SPECIAL FEATURES

• Very good stiffness and impact balance
• Good gloss and transparency
• Low blooming
• Excellent hinge properties

PROCESSING TECHNIQUES

RE420MO is easy to process with standard injection moulding machines and injection stretch

blow moulding machines.

Following parameters should be used as guidelines:

Melt temperature 220 - 260 °C

Holding pressure 200 - 500 bar

Mould temperature 30 - 40 °C

Injection speed High

Shrinkage 1 - 2 %, depending on wall thickness and moulding parameters

Repol SRX100 is recommended for Injection Moulding and Stretch Blow Moulding process. It is an ideal material for Ultra high clarity containers, houseware, ISBM products and appliance parts. The grade contain clarifier and antistatic agent.

Application :

Ultra clarity random copolymer, IM & ISBM rigid containers, houseware, appliance parts

Regulatory Information

Meets the requirements stipulated in IS 10910 on “Specification for Polypropylene and its copolymers for safe use in contact with foodstuffs, pharmaceuticals, and drinking water”. Additives ncorporated in this grade conform to the positive list of constituents as prescribed in IS 10909. The grade and the additives incorporated in it also comply with the FDA:CFR Title 21, 177.1520, Olefin polymers.

Storage Recommendations

Bags should be stored in dry conditions at temperatures below 50°C and protected from UV / direct sunlight

Description

Luban polypropylene is manufactured using Novolen vertical stirred Gas-phase polymerization process. Luban HP4128N is a homopolymer polypropylene with superior slip and anti-blocking properties.

Application

Tubular quench (TQPP) and Cast film, flexible packaging including textiles over raps, garment bags, snack food packaging and straws.

Processing Guidlines

L/D ratio 24.1 – 30.1

Compression ratio 3.1 – 4.1

Melt Temperature  200 – 250 ° C

Pellets Drying    Not essential but helps in insuring consistent feed to extruder

Storage and Handling

Luban HP4128N must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material.

Safety

Luban HP4128N is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet.

Food Contact

Luban HP4128N meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration

Recycling

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

DESCRIPTION

SABIC® PP 37MK10 is a impact copolymer polypropylene resin and is typically used for industrial injection molding application. Molded parts made from this resin typically exhibits good impact, high stiffness and good heat stability. This product is formulated with nucleating agent.

TYPICAL APPLICATIONS

SABIC® PP 37MK10 can be used to produceCrates, electrical appliances, thin wall applications and industrial applications

PROCESSING CONDITIONS

Typical Processing conditions for 37MK10 are:

Recommended melt temperature : 190 – 230 °C

STORAGE AND HANDLING

Polypropylene resin should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably do not exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PP resin within 6 months after delivery.

DESCRIPTION

HE125MO is a versatile polypropylene homopolymer intended for injection moulding.

This product shows very good stiffness and toughness.

APPLICATIONS

• Closures
• Houseware
• Garden furniture
• Compounds and master batches

SPECIAL FEATURES

• Good flow behaviour
• High stiffness

PROCESSING CONDITIONS

• HE125MO is easy to process with standard injection moulding machines.
• Following parameters should be used as guidelines:
• Melt temperature: 220 - 260°C
• Holding pressure: 200 - 500bar As required to avoid sink marks
• Mould temperature: 20 - 40°C
• Injection speed: High
• Shrinkage 1 - 2%, depending on wall thickness and moulding parameters

STORAGE

HE125MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

RECYCLING

The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

RELATED DOCUMENTS

The following related documents are available on request, and represent various aspects on the usability, safety, recovery and disposal of the product.

Safety Information Sheet Statement on chemicals, regulations and standards Statement on compliance to food contact regulations

DESCRIPTION

RE425MO is a versatile designed transparent polypropylene random copolymer with medium melt flow rate intended for injection moulding and injection stretch blow moulding.

RE425MO is suitable for high speed injection moulding with excellent clarifier and demoulding properties. Articles produced from this product have excellent transparency, excellent impact strength at ambient and refrigerator temperatures, good organoleptic properties, low blooming, good denesting performance and excellent hinge properties

APPLICATIONS

• Lids
• Food storage containers
• Houseware containers
• Sports and drinking bottles
• Customized / hinged closures
• Transparent pails

SPECIAL FEATURES

• Excellent impact performance
• Low blooming
• Very good gloss and transparency
• Excellent hinge properties

PROCESSING CONDITIONS

RE425MO is easy to process with standard injection moulding -and injection stress blow moulding machines.

Following parameters should be used as guidelines:

Melt temperature: 220 - 260°C

Holding pressure: 200 - 500bar

Mould temperature: 30 - 40°C

Injection speed: High

Shrinkage 1 - 2%, depending on wall thickness and moulding parameters

STORAGE

RE425MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product.

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

DESCRIPTION

HD915CF is a Homopolymer grade produced by the proprietary Borstar® process. This grade is a highly Crystalline Homopolymer resin based on Borstar Nucleation Technology (BNT) offering high stiffness to film structure. This grade is designed for Metalisable Cast Film (MCPP) applications.

APPLICATIONS

• Metallisable Cast films
• Lamination film
• Core layer in co-extrusion film
• Food packaging film
• Twist Wrap film
• Textile packaging film
• Higher stiffness label film

SPECIAL FEATURES

• Excellent metal adhesion
• High stiffness
• Good Corona retention
• Excellent barrier properties
• Very good heat resistance
• Low migration
• Good processability Good optics (Haze & Gloss

PROCESSING GUIDELINES

The actual conditions will depend on the type of equipment used. Specific recommendations for processing conditions can be determined only when the application and type of equipment are known. Please contact your local Borouge representative for such particulars

FOOD CONTACT REGULATIONS

HD915CF fulfils the food contact regulations in most countries. For specific information and compliance statement please contact your Borouge representative

STORAGE

HD915CF should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product.

SAFETY

The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

Description

Luban HP2106N is manufactured using the Spheripol Technology. Luban HP2106N is a homopolymer polypropylene used for general purpose injection molding applications. It exhibits good flow and stiffness. Luban HP2106N is suitable for food contact.

Application

General purpose injection molding, closures, furniture, houseware

Note: These are typical properties only and are not to be construed as specifications. Users should confirm results by their own tests.

The Typical Processing Conditions for Luban HP2106N are:

Melt temperature 220 – 260 °C

Holding pressure 200 – 500 bar Maximum to avoid sink marks

Mold temperature 20 – 40 °C

Injection speed High

Shrinkage 1 – 2 % depending on wall thickness and molding parameters

Storage and Handling

Luban HP2106N must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material.

Safety

Luban HP2106N is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet.

Food Contact

Luban HP2106N meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration”.

Product Description

Moplen EP332L is a heterophasic copolymer with medium flow used in injection molding. This grade is characterized by a medium stiffness-impact balance at low temperature as well as a low warpage tendency. The additive formulation provides a good heat aging resistance. Moplen EP332L is typically used by customers requiring a high resistance to temperature degradation, in particular for battery cases and automotive components.

This grade is not intended for medical and pharmaceutical applications.

Status Commercial: Active

Availability Africa-Middle East; Asia-Pacific; Australia and New Zealand; Europe; South & Central America

Application Battery Cases

Market Automotive; Consumer Products; Industrial, Building & Construction

Processing Method Injection Molding

Attribute Good Heat Aging Resistance; Good Impact Resistance; Good Stiffness; Heat

Stabilized; Impact Copolymer; Low Warpage

Health and Safety

The resin is manufactured to the highest standards, but special requirements apply to certain applications such as food end-use contact and direct medical use. For specific information on regulatory compliance contact you ocal representative.

Workers should be protected from the possibility of skin or eye contact with molten polymer. Safety glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to the eyes.

Molten polymer may be degraded if it is exposed to air during any of the processing and off-line operations. The products of degradation may have an unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes or vapours. Legislation on the control of emissions and pollution prevention should be observed.

Repol H200FG is recommended for use in Fiber Spinning operations, for making multifilament yarn and staple fiber. Repol H200FG has excellent uniformity needed for high speed spinning of fine deniers. Repol H200FG contains an excellent process stabilizer package suitable for non-woven and filament products. Formulated for gas fading resistance.

Typical Processing Conditions

Extrusion Temperature: 210 – 250 °C

Quenching Temperature: 10 – 20 °C

Godet rolls Temperature: 80 – 120 °C

Draw Ratio: 2.8 – 3.2

Texturizing Temperature: 125 – 165 °C

Note: Processing parameters mentioned above are for reference only and not to be considered as specifications. They may vary based on the product to be manufactured.

Regulatory Information

The product complies with Indian Standard IS 10910 on “Specification for polypropylene and its copolymers for safe use in contact with foodstuffs, pharmaceuticals and drinking water. It also conforms to IS 16738:2018 on positive list of constituents for polypropylene, polyethylene and their copolymers for its safe use in contact with foodstuffs and pharmaceuticals. The grade and the additives incorporated in it also comply with the FDA:CFR Title 21, 177.1520, Olefin polymers

Storage Recommendations

Bags should be stored in dry / closed conditions at temperatures below 50°C and protected from UV / direct sunlight