Verified
Add Review
Our Products
Synthetic Resin
2 Products availablePET Granules
1 Products availablePlastic Polymers
1 Products availableWe offer the best product range of EGDA-6888 Equate HDPE Film Extrusion, luban hp2100s hdpe granules, Polyethylene H350FG Reliance Homopolymer Granules, Borouge Black 3490 LS HDPE Granules and black borouge he1440 hdpe granules.
DESCRIPTION
EGDA-6888 is a high molecular weight, high density polyethylene copolymer that has been designed specifically for tubular film extrusion. Its broad molecular weight distribution and density have been optimized to give excellent bubble stability at high extrusion rates with high film strength and rigidity. The combination of high strength and excellent drawdown-ability makes EGDA-6888 ideal for down gauging in many applications.
APPLICATIONS
Tubular films produced from EGDA-6888 are recommended for high strength grocery sacks, shopping bags, produce bags and high quality thin films for multiwall sack liners and replacements for thin paper products. EGDA-6888 is also suitable for making non-pressure “gravity” pipes for drainage and sewage applications.
Film properties are typical of blown films extruded at a 4:1 blow-up ratio and melt temperature of 215 C. ASTM: American Society for Testing and Materials
EXTRUSION CONDITIONS
EGDA-6888 can be extruded on conventional HDPE blown film equipment at 215C melt temperature. A flat or moderately increasing temperature profile is recommended for its extrusion.
A 4:1 blow-up ratio and high stalk bubble configuration are always recommended for products requiring high strength. Lower blow-up ratios (3:1) can be used for products that do not require high strength.
For best gauge uniformity, a minimum extrusion rate of 0.14 kgs/hr/mm of die circumference is recommended. The best balance of extrudability and film strength is obtained with a 1.0 to 1.1 mm die gap.
FOOD CONTACT USAGE
EGDA-6888 can be used for all food contact applications including holding food during cooking. It conforms to US FDA Regulation 21 CFR 177.1520 as well as EC Directive 90/128/EEC and its amendments to-date. Food contact suitability certificate is available upon request.
AVAILABILITY
EGDA-6888 is supplied in 25 Kg bags in secured pallets of 55 bags (1.375 MT net). It is also supplied in sea bulk container of up to 20 MT.
STORAGE AND HANDLING
EGDA-6888 is supplied in pellet form and is readily conveyed on conventional polyethylene bulk handing equipment. The bulk handling system should be designed to prevent accumulation of fines and dust particles that can pose an explosion hazard. Ensure all equipment is properly grounded. The product should be stored in a cool dry shaded area away from dust, sunlight and heat. For more details on storage and handling see our Polyethylene Storage and Handling Guide. Also carefully review the Material Safety Data Sheet supplied with this product for health, safety and waste considerations.
IMPORTANT NOTICE
The information supplied in this bulletin to the best of our knowledge is accurate and factual as of the date printed. It is offered solely as a convenience to EQUATE’s customers and is intended only as a guide for EGDA-6888. Since the user’s specific applications and conditions of use are beyond EQUATE’s control, EQUATE makes no warranty or representation regarding results that may be obtained by the user. It shall be the responsibility of the user to determine the suitability of the product for the user’s specific application. The information disclosed in this document is not to be construed as a recommendation to use the product in infringement of any patent rights covering the usage.
Description
Luban polypropylene is manufactured using Novolen vertical stirred Gas-phase polymerization process. Luban HP2100S is a Homopolymer polypropylene with good flowability and stiffness for general applications.
Application
Thin walled packaging, household articles & general purpose injection molding.
Note: These are typical properties only and are not to be construed as specifications. Users should confirm results by their own tests.
The Typical Processing Conditions for Luban HP2100S are:
Melt temperature 220 – 260 °C
Holding pressure 200 – 500 bar Maximum to avoid sink marks
Mold temperature 20 – 40 °C
Injection speed High
Shrinkage 1 – 2 % depending on wall thickness and molding parameters
Storage and Handling
Luban HP2100S should be stored in well ventilate area during handling or processing of to prevent accumulation of dust and fumes. Avoid contact with strong oxidizers, excessive heat, sparks or open flame as this could well speed up alteration and consequently loss of quality of the material in which could lead to unforeseen dangers. The bags must be protected from direct sunlight and should be stored in shaded and completely dry area for good processing.
Safety
Luban HP2100S is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet.
Food Contact
Luban HP2100S meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended fo direct food contact. For additional information on approved conditions of use for food contac applications, please refer to the “Product Stewardship Declaration”.
Recycling
The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.
Repol H350FG is recommended for use in Fiber Spinning operations, for making multifilament yarn, and Nonwovens. Repol H350FG has excellent uniformity needed for high-speed spinning of fine deniers. Repol H350FG contains excellent process stabilizer package suitable for non-woven and filament products. Formulated for gas fading resistance.
Typical Processing Conditions
Extrusion Temperature: 220 – 260 °C Note: Processing parameters mentioned above are for reference only and not to be considered as specifications. They may vary based on the product to be manufactured. May be used for other applications such as extrusion coating, it is recommended to blend with extrusion coating grade of Low-density polyethylene (LDPE).
Regulatory Information
The product complies with Indian Standard IS 10910 on “Specification for polypropylene and its copolymers for safe use in contact with foodstuffs, pharmaceuticals and drinking water. It also conforms to IS 16738:2018 on positive list of constituents for polypropylene, polyethylene and their copolymers for its safe use in contact with foodstuffs and pharmaceuticals. The grade and the additives incorporated in it also comply with the FDA:CFR Title 21, 177.1520, Olefin polymers
Storage Recommendations
Bags should be stored in dry / closed conditions at temperatures below 50°C and protected from UV / direct sunlight
DESCRIPTION
Borstar HE3490-LS is a black, bimodal, high density polyethylene classified as a MRS 10.0 material (PE100) produced by the advanced Borstar technology. Well dispersed carbon black gives outstanding UV resistance. Long term stability is ensured by an optimised stabilisation system.
Borstar HE3490-LS is now registered with the international Traceability coding (Traccoding), under the code R01, in support of ISO12176-4 (2003).
APPLICATIONS
Borstar HE3490-LS is recommended for pressure pipe systems in the applications field of drinking water and natural gas, pressure sewerage, relining, sea outfall and industrial. It is especially designed for the production of larger diameter, thick wall pipe, but can be processed for the whole range of diameters. It also shows excellent resistance to rapid crack propagation and slow crack growth.
PROCESSING GUIDELINES
The actual extrusion conditions will depend on the type of equipment used. They will also depend on size and wall thickness of the pipe produced. The following conditions may be used as a guideline when starting up the extruder:
Cylinder 190 – 210°C
Head 200 – 210°C
Die 200 – 210°C
Melt temperature 200 – 220°C
DESCRIPTION
Description
Borstar®HE1440 is a Black, bimodal HDPE product produced using the proprietary Borstar® bimodal technology which offers excellent melt strength and process ability for sprinkler pipe extrusion and drip lateral with superior mechanical properties.
CAS-No. 25087-34-7
APPLICATIONS
HE1440 is recommended for
KEY FEATURES
HE1440 offers excellent balance of process-ability and mechanical properties
PROCESSING CONDITIONS
The actual extrusion conditions will depend on type of equipment used and the size and wall thickness of the pipe required. Following conditions should be used as a guide for the starting up the extruder.
Barrel Zone 180 – 210 Deg C
Die Zone 190 – 210 Deg C
Please contact your local Borouge representative for specific recommendation for the processing conditions.
STORAGE
This product should be stored in dry conditions at temperature bellow 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and can have negative effects on physical properties of this product.
More information on storage can be found in Safety Information Sheet (SIS) for this product.
SAFETY
The product is not classified as a hazardous mixture.
Dust and fines from the product carry a risk of dust explosion. All equipment should be properly earthed. Inhalation of dust should be avoided as it may cause irritation of the respiratory system. Small amounts of fumes are generated during processing of the product. Proper ventilation is therefore required.
Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.
RECYCLING
The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.
Product Description
Lupolen 2221F is a fractional melt index homopolymer LDPE resin designed for film applications requiring an excellent balance of clarity, stiffness, shrink and strength. 2221F is selected by customers for collation shrink films, pallet shrink films, packaging films and heavy duty films where clarity and stiffness are important. 2221F contains an antioxidant.
Notes
Data obtained from 50 micron film produced on a 50 mm extruder with a 100 mm die, 205°C melt temperature, 2.5:1 BUR, 0.635 mm die gap at 27 kg/hr. These are typical property values not to be construed as specification limits.
Processing Techniques
Specific recommendations for resin type and processing conditions can only be made when the end use, required properties and fabrication equipment are known.
Product Description
Hostalen ACP 5831 D is a high density polyethylene with an excellent combination of stiffness and stress crack resistance. It is delivered in pellet form containing antioxidants and typically used for small bow molding applications in the food and consumer segment and for toys.
Hostalen ACP 5831 D
Conveying: Conveying equipment should be designed to prevent production and accumulation of fines and dust particles that are contained in polymer resins. These particles can under certain conditions pose an explosion hazard. We recommend the conveying system used is equipped with adequate filters, is operated and maintained that no leak develops and adequate grounding exists at all times.
Health and Safety:
The resin is manufactured to the highest standards but, special requirements apply to certainapplications such as food end-use contact and direct medical use. For specific information onregulatory compliance contact your local representative. Workers should be protected from the possibility of skin or eye contact with molten polymer. Safety
glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to the eyes. Molten polymer may be degraded if it is exposed to air during any of the processing and off-line operations. The products of degradation have an unpleasant odour. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes or vapours. Legislation on the control of emissions and pollution prevention must be observed. If the principles of sound manufacturing practice are adhered to and the place of work is well ventilated, no health hazards are involved in processing the resin.
The resin will burn when supplied with excess heat and oxygen. It should be handled and stored away from contact with direct flames and/or ignition sources. In burning the resin contributes high heat and may generate a dense black smoke. Starting fires can be extinguished by water, developped fires should be extinguished by heavy foams forming an aqueous or polymeric film. For further information about safety in handling and processing please refer to the Material Safety Data Sheet.
Storage:
The resin is packed in 25 kg bags or in bulk containers protecting it from contamination. If it is stored under adverse conditions, i. e. if there are large fluctuations in ambient temperature and the atmospheric humidity is high, moisture may condense inside the packaging. Under these circumstances, it is recommended to dry the resin before use. Unfavourable storage conditions may also intensify the resin´s slight characteristic odour.
The resin is subjected to degradation by ultra-violet radiations or by high storage temperatures. Therefore the resin must be protected from direct sunlight, temperatures above 40°C and high atmospheric humidity during storage. The resin can be stored over a period of more than 6 month without significant changes in the specified properties, appropriate storage conditions provided. Higher storage temperatures reduce the storage time. The information submitted is based on our current knowledge and experience. In view of the many
factors that may affect processing and application, these data do not relieve processors of the responsibility of carrying out their own tests and experiments; neither do they imply any legally binding assurance of certain properties or of suitability for a specific purpose. The data do not relieve the customer from his obligation to control the resin upon arrival and to complain about faults. It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are observed.
Description
Borstar®HE1490 is a Black, bimodal HDPE product produced using the proprietary Borstar® bimodal technology which offers excellent melt strength and process ability for sprinkler pipe extrusion and drip lateral with superior mechanical properties.
CAS-No. 25087-34-7
APPLICATIONS
HE1440 is recommended for
KEY FEATURES
HE1440 offers excellent balance of process-ability and mechanical properties
PROCESSING CONDITIONS
The actual extrusion conditions will depend on type of equipment used and the size and wall thickness of the pipe required. Following conditions should be used as a guide for the starting up the extruder.
Barrel Zone 180 – 210 Deg C
Die Zone 190 – 210 Deg C
Please contact your local Borouge representative for specific recommendation for the processing conditions.
STORAGE
This product should be stored in dry conditions at temperature bellow 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and can have negative effects on physical properties of this product.
More information on storage can be found in Safety Information Sheet (SIS) for this product.
SAFETY
The product is not classified as a hazardous mixture.
Dust and fines from the product carry a risk of dust explosion. All equipment should be properly earthed. Inhalation of dust should be avoided as it may cause irritation of the respiratory system. Small amounts of fumes are generated during processing of the product. Proper ventilation is therefore required.
Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.
RECYCLING
The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.
M60075 is a high Density Polythylene ( HDPE ) grade suitable for injection moulding applications where good mechanical properties are essential with gloss, dimensional stabligy, good ESCR, required for technical moudlgins like moulded crates, luggage shells, helmests, defence, applicatin etd.
DESCRIPTION
HE1490 is a natural, bimodal HDPE offers excellent melt strength and process ability for drip lateral and sprinkler pipe extrusion.
HE1490 has optimized weldability and high mechanical properties like, tensile strength, and elongation. It is produced with the proprietary Borstar® bimodal technology which provides the polymer very high ESCR and longer service life in agriculture.
CAS-No. 25087-34-7
APPLICATIONS
HE1490 is recommended for:
Range of wall thickness drip irrigation tubing for online drip laterals and flat as well as cylindrical emitting pipe/inline production Sprinkler Irrigation Pipes Non Pressure Utility Pipes Thin Walled Corrugated Pipes.
KEY FEATURES HE1490 offers excellent balance of ESCR, process-ability and mechanical properties
PROCESSING CONDITIONS
The actual extrusion conditions will depend on type of equipment used and the size and wall thickness of the pipe required. Following conditions should be used as a guide for starting up the extruder.
STORAGE
This product should be stored in dry conditions at temperature bellow 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product
SAFETY
HE1490 is not classified as a hazardous mixture.
Dust and fines from the product carry a risk of dust explosion. All equipment should be properly earthed. Inhalation of dust should be avoided as it may cause irritation of the respiratory system. Small amounts of fumes are generated during processing of the product. Proper ventilation is therefore required.
Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.
RECYCLING
The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.
RELATED DOCUMENTS
The following related documents are available on request, and represent various aspects on the usability, safety, recovery and disposal of the product.
Safety Information Sheet
Statement on chemicals, regulations and standards
Statement on compliance to regulations for drinking water pipes
Description.
SABIC® HDPE B5429 is a medium molecular weight high density polyethylene copolymer. It is primarily intended for blow moulding bottles of small sizes. SABIC® HDPE B5429 offers an excellent combination of toughness, stress cracking resistance (ESCR), load bearing strength and processability characteristics.
Typical applications.
SABIC® HDPE B5429 is classified as a multipurpose blow moulding grade. It may be blow moulded into containers for household and industrial chemicals (e.g. detergents, bleach, fabric softeners, solvents, paints, etc.), automotive supplies, foodstuffs, toiletries and cosmetics. It can also be used in other hollow thin-walled parts and profile extrusions.
Processing conditions.
SABIC® HDPE B5429 has been run on the latest high speed blow moulding machines at maximum rates to produce articles of excellent quality. Moulded parts exhibit outstanding surface appearance. The recommended melt temperature for this grade is between 165 and 215 °C.
General information. The SABIC® HDPE product range for blow moulding and extrusion is produced in a slurry – or gasphase process using a Cr catalyst. The primary characteristic of SABIC® HDPE grades is a broad molecular weight distribution, which ensures excellent behaviour during extrusion. Additional characteristics are a high purity, excellent stability during processing and a high intrinsic toughness. The carefully balance of environmental stress crack resistance and stiffness is becoming visible on grade level. Typical application area: bottles, cans, containers and technical articles, sheet and thermoforming, profiles and tubes for pressure less applications.
Health, Safety and Food Contact regulations. Detailed information is provided in the relevant Material Safety Datasheet and or Standard Food Declaration, available on the Internet (www.SABIC-europe.com). Additional specific information can be requested via your local Sales Office.
Quality. SABIC Europe is fully certified in accordance with the internationally accepted quality standard ISO 9001-2000. It is SABIC Europe's policy to supply materials that meet customers specifications and needs and to keep up its reputation as a pre-eminent, reliable supplier of e.g. polyethylenes.
Storage and handling. Polyethylenes resins (in pelletised or powder form) should be stored in such a way that it prevents exposure to direct sunlight and/or heat, as this may lead to quality deterioration. The storage location should also be dry, dust free and the ambient temperature should not exceed 50 °C. Not complying with these precautionary measures can lead to a degradation of the product which can result in colour changes, bad smell and inadequate product performance. It is also advisable to process polyethylene resins (in pelletised or powder form) within 6 months after delivery, this because also excessive aging of polyethylene can lead to a deterioration in quality.
Environment and recycling. The environmental aspects of any packaging material do not only imply waste issues but have to be considered in relation with the use of natural resources, the preservations of foodstuffs, etc. SABIC Europe considers polyethylene to be an environmentally efficient packaging material. Its low specific energy consumption and insignificant emissions to air and water designate polyethylene as the ecological alternative in comparison with the traditional packaging materials. Recycling of packaging materials is supported by SABIC Europe whenever ecological and social benefits are achieved and where a social infrastructure for selective collecting and sorting of packaging is fostered. Whenever 'thermal' recycling of packaging (i.e. incineration with energy recovery) is carried out, polyethylene -with its fairly simple molecular structure and low amount of additives- is considered to be a trouble-free fuel.
Description
Luban DGDX-6097 is a high molecular weight, high-density polyethylene copolymer that has been designed specifically for tubular film extrusion. Its broad molecular weight distribution and density successfully combine to give excellent performance at high extrusion rates with high film strength and rigidity. The grade is recommended for high strength grocery sacks, shopping bags and notion and millinery bags. The excellent drawdown characteristic of this product permits production of high-quality thin films for multi-wall sack liners and replacement for thin paper products. The combination of strength and drawdown makes this resin ideal for downgauging in many applications. The grade is compatible with color concentrates, thus permitting the production of a variety of colored films that serve as protective and attractive decorative wraps.
Main Characteristics:
• Butene High Density Resin
• High film strength
• Excellent drawdown
Application
High strength grocery sacks, shopping bags and notion and millinery bags
Storage and Handling
Luban DGDX-6097 must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material.
Safety
Luban DGDX-6097 is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet.
Food Contact
Luban DGDX-6097 meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration”.
Recycling
The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.
Properties (Typical Values)
| Property | Unit | Test method | Value |
|---|---|---|---|
| Melt Index (190°C/2.16 kg) | g/10 min | ASTM D1238 | 0.05 |
| Melt Index (190°C/21.6 kg) | g/10 min | ASTM D1238 | 10.5 |
| Density | g /cm³ | ASTM D792 | 0.948 |
| Flexural Modulus - 1% Secant | MPa | ASTM D7901 | 1040 |
| Tensile stress at yield (MD/TD) | MPa | ASTM D8822 | 30/27 |
| Tensile stress at break (MD/TD) | MPa | ASTM D8822 | 51/60 |
| Tensile strain at break (MD/TD) | % | ASTM D8822 | 220/400 |
| Dart Drop Impact (12.7 μm) | g | ASTM 1709A2 | 127 |
| Vicat Softening Temperature | °C | ASTM D1525 | 123 |
| Melting Temperature (DSC) | °C | ASTM D3418 | 129 |
Product Description
Lupolen 2427 K is an additivated, low density polyethylene. It contains an antioxidant, slip and anti-blocking agent. It is characterized by a good processability. Films made from Lupolen 2427 K exhibit good optical properties. It is delivered in pellet form.
This product is not intended for use in medical and pharmaceutical applications.
Status Commercial: Active
Availability Africa-Middle East; Asia-Pacific; Europe
Application Food Packaging Film; Hygiene Film; Shrink Film
Market Flexible Packaging
Processing Method Blown Film; Cast Film
Attribute Antioxidant; Good Heat Seal; Good Optical Properties; Good Processability; Low
Friction; Unspecified Antiblocking; Unspecified Slip
Health and Safety
The resin is manufactured to the highest standards, but special requirements apply to certain applications such as food end-use contact and direct medical use. For specific information on regulatory compliance contact your local representative.
Workers should be protected from the possibility of skin or eye contact with molten polymer. Safety glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to the eyes.
Molten polymer may be degraded if it is exposed to air during any of the processing and off-line operations. The
products of degradation may have an unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes or vapours. Legislation on the control of emissions and pollution prevention should be observed. The resin will burn when supplied with excess heat and oxygen. It should be handled and stored away from contact with direct flames and/or ignition sources. While burning, the resin contributes high heat and may generate a dense black smoke.
Recycled resins may have previously been used as packaging for, or may have otherwise been in contact with, hazardous goods. Converters are responsible for taking all necessary precautions to ensure that recycled resins are safe for continued use. For further information about safety in handling and processing please refer to the Safety Data Sheet
DESCRIPTION
EMDA-6200 grade is a high-density polyethylene copolymer resin designed for blow molding small to medium size bottles. It can be used on intermittent as well as continuous blow molding machines for high-speed production of high quality bottles. The bottles have excellent environmental stress cracking resistance and a good balance of rigidity and impact strength. They are easily trimmed and exhibit excellent surface attributes.
APPLICATIONS
EMDA-6200 is intended for producing containers of up to 10 liter capacity for packaging household and industrial chemicals (detergents, bleach, fabric softeners, etc.) toiletries, cosmetics and food products. It is als suitable for producing thin-walled parts and household items In addition EMDA-6200 can also be used successfully for extruding sheets and profiles including corrugated drainage Pipes.
FOOD CONTACT USAGE
EMDA-6200 can be used for all food contact applications including holding food during cooking. It conforms to US FDA Regulation 21 CFR 177.1520 as well as EC Directive 90/128/EEC and its amendments to-date. Food contact suitability certificate is available upon request.
AVAILABILITY
EMDA-6200 is supplied in 25-Kg bags in secured pallets of 55 bags (1.375 MT net). It is also supplied in sea bulk containers of up to 15 MT capacity.
STORAGE AND HANDLING
EMDA-6200 is supplied in pellet form and is readily conveyed on conventional polyethylene bulk handing equipment. The bulk handling system should be designed to prevent accumulation of fines and dust particles that can pose an explosion hazard. Ensure all equipment is properly grounded. The product should be stored in a cool dry shaded area away from dust, sunlight and heat. For more details on storage and handling see our Polyethylene Storage and Handling Guide. Also carefully review the Material Safety Data Sheet supplied with this product for health, safety and waste considerations.
IMPORTANT NOTICE
The information supplied in this bulletin to the best of our knowledge is accurate and factual as of the date printed. It is offered solely as a convenience to EQUATE’s customers and is intended only as a guide for EMDA-6200. Since the user’s specific applications and conditions of use are beyond EQUATE’s control, EQUATE makes no warranty or representation regarding results that may be obtained by the user. It shall be theresponsibility of the user to determine the suitability of the product for the user’s specific application. The information disclosed in this document is not to be construed as a recommendation to use the product in infringement of any patent rights covering the usage.
TYPICAL PROPERTIES
Environmental Stress Cracking Resistance
* 41g Boston Round quart (0.946 liter) bottle
ASTM – American Society for Testing and Materials
TYPICAL MOLDING CONDITIONS
DESCRIPTION
BorPure™MB6562 is a multimodal, high-density polyethylene intended for both injection and compression moulding. This grade combines good organoleptic properties and very good flow properties with a controlled torque level due to the incorporation of slip agent.
The broad molecular weight distribution guarantees superior environmental stress crack resistance.
CAS-No. 25087-34-7
APPLICATIONS
KEY FEATURES
PROCESSING CONDITIONS
This product is easy to process with standard injection moulding machines, as well as on compression moulding equipment
Injection Moulding
Following injection moulding parameters should be used as guidelines:
Melt temperature: 190 - 250 °C
Mould temperature: 10 - 40 °C
Injection speed: As high as possible
Shrinkage 1 - 2 %, depending on wall thickness and moulding parameters
Compression Moulding
Following compression moulding parameters should be used as guidelines
Extruder temperature profile 160 - 195 °C
Melt temperature: 180 - 200 °C
Mould temperature: 10 - 40 °C
Shrinkage 1 - 2 %, depending on wall thickness and moulding parameters
Please contact your local Borouge representative for specific recommendations for processing conditions
FOOD CONTACT REGULATIONS
BorPure™MB6562 fulfils the food contact regulations in most countries. If required, contact your Borouge / Borealis representative for a certificate.
STORAGE
BorPure™MB6562 should be stored in dry conditions at temperature bellow 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on physical properties of this product More information on storage can be found in Safety Information Sheet (SIS) for this product
Product Description
Hostalen CRP 100 black is a high density polyethylene (HDPE), black coloured similar RAL 9004 with high melt viscosity for extrusion, injection and compression moulding. The product is classified as PE 100 and provides excellent stress crack resistance properties (ESCR) combined with very good long term hydrostatic strength
This grade is not intended for medical and pharmaceutical applications.
This grade is supported for use in drinking water applications.Notes
Notes
These are typical property values not to be construed as specification limits.
Processing Techniques
Users should determine the conditions necessary to obtain optimum product properties and suitability of the product for the intended application.
Recommended melt temperatures: 190 °C to 230 °C.
Specific recommendations for resin type and processing conditions can only be made when the end use, required properties and fabrication equipment are known.
Health and Safety:
The resin is manufactured to the highest standards, but special requirements apply to certain applications such as food end-use contact and direct medical use. For specific information on regulatory compliance contact your local representative.
Workers should be protected from the possibility of skin or eye contact with molten polymer. Safety glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to the eyes.
Molten polymer may be degraded if it is exposed to air during any of the processing and off-line operations. The products of degradation may have an unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes or vapours. Legislation on the control of emissions and pollution prevention should be observed.
The resin will burn when supplied with excess heat and oxygen. It should be handled and stored away from contact with direct flames and/or ignition sources. While burning, the resin contributes high heat and may generate a dense black smoke.
Recycled resins may have previously been used as packaging for, or may have otherwise been in contact with, hazardous goods. Converters are responsible for taking all necessary precautions to ensure that recycled resins are safe for continued use.
For further information about safety in handling and processing please refer to the Safety Data Sheet.
Conveying:
Conveying equipment should be designed to prevent production and accumulation of fines and dust particles
that are contained in polymer resins. These particles can under certain conditions pose an explosion hazard. Conveying systems should be grounded, equipped with adequate filters and regularly inspected for leaks.
Storage:
The resin is packed in 25 kg bags, octabins or bulk containers protecting it from contamination. If it is stored under certain conditions, i. e. if there are large fluctuations in ambient temperature and the atmospheric humidity is high, moisture may condense inside the packaging. Under these circumstances, it is recommended to dry the resin before use. Unfavorable storage conditions may also intensify the resin's slight characteristic odor.
Resin should be protected from direct sunlight, temperatures above 40°C and high atmospheric humidity during storage. Higher storage temperatures may reduce the storage time.
The information submitted is based on our current knowledge and experience. In view of the many factors that may affect processing and application, these data do not relieve processors of the responsibility of carrying out their own tests and experiments; neither do they imply any legally binding assurance of certain properties or of suitability for a specific purpose. This information does not remove the obligation of the customer to inspect the material on arrival and notify us of any faults immediately. It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are observed
Description
Luban DGDZ 6095 is a high molecular weight, high-density polyethylene copolymer that has been designed specifically for tubular film extrusion. Its broad molecular weight distribution and density successfully combine to give excellent performance at high extrusion rates with high film strength and rigidity. The grade is recommended for high strength grocery sacks, shopping bags and notion and millinery bags. The excellent drawdown characteristic of this product permits production of high-quality thin films for multi-wall sack liners and replacement for thin paper products. The combination of strength and drawdown makes this resin ideal for downgauging in many applications. The grade is compatible with color concentrates, thus permitting the production of a variety of colored films that serve as protective and attractive decorative wraps.
Main Characteristics:
• Butene High Density Resin
• High film strength
• Excellent drawdown
Application
High strength grocery sacks, shopping bags and notion and millinery bags
Storage and Handling
Luban DGDZ 6095 must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material.
Safety
Luban DGDZ 6095 is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet.
Food Contact
Luban DGDZ 6095 meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration”.
Recycling
The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.
Properties (Typical Values)
| Property | Unit | Test method | Value |
| Melt Index (190°C/2.16 kg) | g/10 min | ASTM D1238 | 0.05 |
| Melt Index (190°C/21.6 kg) | g/10 min | ASTM D1238 | 10.5 |
| Density | g /cm³ | ASTM D792 | 0.948 |
| Flexural Modulus - 1% Secant | MPa | ASTM D7901 | 1040 |
| Tensile stress at yield (MD/TD) | MPa | ASTM D8822 | 30/27 |
| Tensile stress at break (MD/TD) | MPa | ASTM D8822 | 51/60 |
| Tensile strain at break (MD/TD) | % | ASTM D8822 | 220/400 |
| Dart Drop Impact (12.7 μm) | g | ASTM 1709A2 | 127 |
| Vicat Softening Temperature | °C | ASTM D1525 | 123 |
| Melting Temperature (DSC) | °C | ASTM D3418 | 129 |
This high molecular weight, hexene copolymer is tailored for blown film applications that require:
This resin meets these specifications:
Typical applications for HHM TR-144 include
1. The nominal properties reported herein are typical of the product, but do not reflect normal testing variance and therefore should not be used for specification purposes. Values are rounded.
2. The physical properties were determined on compression moulded specimens that were prepared in accordance with Procedure C of ASTM D4703, Annex A1.
3. Based on 0.025 mm film produced at 4:1 blow-up ratio.
Technical Specifications
| Nominal Resin Properties(1,2) | Value (SI Units) | Method |
|---|---|---|
| Density | 0.946 g/cm3 | ASTM D1505 |
| Melt Index, Condition 190°C / 2.16 kg | 0.18 g/10 min | ASTM D1238 |
| Brittleness Temperature, Type A clamp, Type I specimen | <-75°C | ASTM D746 |
| ESCR, Condition B (100% Igepal), F50 | >1000 hrs | ASTM D1693 |
| Flexural Modulus, Tangent - 16:1 span:depth, 12.7 mm/min | 1150 MPa | ASTM D790 |
| Nominal Blown Film Properties at 0.025mm(1,3) | Value (SI Units) | Method |
| Dart Drop (66 cm) | 90 g | ASTM D1709 |
| Tensile Strength at Yield, 50.8 mm/min MD | 24 MPa | ASTM D882 |
| Tensile Strength at Yield, 50.8 mm/min TD | 26 MPa | ASTM D882 |
| Elongation at Break, 50.8 mm/min MD | 4.8 | ASTM D882 |
| Elongation at Break, 50.8 mm/min TD | 6.4 | ASTM D882 |
| Elmendorf Tear Strength, MD | 19 g | ASTM D1922 |
| Elmendorf Tear Strength, TD | 270 g | ASTM D1922 |
Description
Luban DMDZ 6147 is a high molecular weight, high-density polyethylene copolymer that has been designed specifically for tubular film extrusion. Its broad molecular weight distribution and density successfully combine to give excellent performance at high extrusion rates with high film strength and rigidity. The grade is recommended for high strength grocery sacks, shopping bags and notion and millinery bags. The excellent drawdown characteristic of this product permits production of high-quality thin films for multi-wall sack liners and replacement for thin paper products. The combination of strength and drawdown makes this resin ideal for downgauging in many applications. The grade is compatible with color concentrates, thus permitting the production of a variety of colored films that serve as protective and attractive decorative wraps.
Main Characteristics:
• Butene High Density Resin
• High film strength
• Excellent drawdown
Application
High strength grocery sacks, shopping bags and notion and millinery bags
Storage and Handling
Luban DMDZ 6147 must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material.
Safety
Luban DMDZ 6147 is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet.
Food Contact
Luban DMDZ 6147 meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration”.
Recycling
The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.
Properties (Typical Values)
| Property | Unit | Test method | Value | ||
|---|---|---|---|---|---|
| Melt Index (190°C/2.16 kg) | g/10 min | ASTM D1238 | 0.05 | ||
| Melt Index (190°C/21.6 kg) | g/10 min | ASTM D1238 | 9 | ||
| Density | g /cm³ | ASTM D792 | 0.948 | ||
| Environmental Stress-Cracking Resistance 122°F (50°C), 10% Igepal, F50 |
hr | ASTM D16931 | >1000 | ||
| Flexural Modulus - 2% Secant | MPa | ASTM D790B1 | 885 | ||
| Tensile stress at yield | MPa | ASTM D6381 | 24.6 | ||
| Tensile stress at break | MPa | ASTM D6381 | 35.5 | ||
| Tensile strain at break | % | ASTM D6381 | 780 | ||
| Tensile Impact Strength | kJ/m² | ASTM D18221 | 462 | ||
| Deflection Temperature Under Load 0.45 MPa, Unannealed |
°C | ASTM D6481 | 66 | ||
| Vicat Softening Temperature | °C | ASTM D1525 | 127 | ||
Description
E180F is EVA resin for crosslinked foam applications including mid-sole and in-sole of athletic shoes. This grade is designed to be processed in conventional kneading and rolling equipment for mixing and dispersing crosslinking agen and foaming agent.
Characteristics
E180F offers good processability during compounding with various additives. Foamed products made from this grade provide excellent spilt tear resistance, superb tensile and elongation properties, and good compression set properties
Applications
Athletic shoe mid-soles and in-soles, Sandals, Cushion padding
Technical Specifications
| Properties | Test Method | Units | E180F |
|---|---|---|---|
| Melt Index (190℃/2.16㎏) | ASTM D 1238 | g/10min | 2 |
| Density | ASTM D 1505 | g/cm3 | 0.94 |
| VA Content | Hanwha Total | % | 18 |
| Tensile Strength at Break | ASTM D 638 | kg/cm2 | 260 |
| Elongation at Break | ASTM D 638 | % | 750 |
| Shore Hardness | ASTM D 2240 | A scale D scale |
92 38 |
| Vicat Softening Point | ASTM D 1525 | ℃ | 64 |
| Melting Point | Hanwha Total | ℃ | 86 |
| Brittleness Temp. | ASTM D 746 | ℃ | < -70 |
Sipchem EVA 2518 CO is an 18% ethylene vinyl acetate copolymer resin, designed for a variety of foam moulding application; manufactured by IPC an affiliate of Sipchem in The Kingdom of Saudi Arabia using an Exxon-Mobil high-pressure tubular process. EVA 2518 CO exhibits low melting temperature, excellent processability and mechanical properties.
1. These are typical properties: these are not to be construed as specifications.
2. This product is not intended for use in medical applications and should not be used in any such applications.
3. Contact your Sipchem Representative for potential food contact application compliance
Typical Characteristics
| Property | Typical Value | Unit | Test Method |
|---|---|---|---|
| Melt Index (190°C / 2.16 kg) | 2.5 | g/10mm | ASTM D1238 |
| Vinyl Acetate Content | 18 | wt% | ASTM D5594 |
| Density | 0.94 | g/cm3 | ASTM D1505 |
| Vicat Softening Point | 64 | °C | ASTM D1525 |
| Melting Point | 87 | °C | ASTM D3418 |
| Tensile Strength at Yield | 5.2 | MPa | ASTM D638 |
| Tensile Strength at Break | 11 | MPa | ASTM D638 |
| Elongation at Yield | 260 | % | ASTM D638 |
| Elongation at Break | >800 | % | ASTM D638 |
| Flexural Modulus | 60 | % | ASTM D790 |
| Hardness Shore A | 76 | ASTM D2240 | |
| Hardness Shore D | 36 | ASTM D2240 |
DESCRIPTION
P4808NA is a high density Polyethylene with multimodal distribution of the molecular mass. This is natural color grade suitable for non-pressure pip applications. It provides good ESCR (environmental stress cracking resistance)
TYPICAL APPLICATIONS
P4808NA is a natural High Density Polyethylene (HDPE) resin specifically designed for non-pressure pipes such as Irrigation, cable conduits and Gravit pipes segment.
PROCESSING CONDITIONS
Typical processing conditions for P4808NA : Melt temperature: 190-220°C
STORAGE AND HANDLING
Polyethylene material / compound should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably don’t exceed 50°C. SABIC would not give warranty to bad storage conditions lead to quality deterioration and inadequate productperformance. It is advisable to process PE resin within 6 months after delivery.
DESCRIPTION
BorPure™MB6561 is a multimodal, high-density polyethylene intended for both injection and compression moulding. This grade exhibits excellent organoleptic properties and very good flow properties with good impact strength.
The broad molecular weight distribution guarantees superior environmental stress crack resistance
CAS-No. 25087-34-7
APPLICATIONS
KEY FEATURES
PROCESSING CONDITIONS
This product is easy to process with standard injection moulding machines, as well as on compression moulding equipment
Injection Moulding
Following injection moulding parameters should be used as guidelines:
Shrinkage 1 - 2 %, depending on wall thickness and moulding parameters
Compression Moulding
Following compression moulding parameters should be used as guidelines
Shrinkage 1 - 2 %, depending on wall thickness and moulding parameters
Please contact your local Borouge representative for specific recommendations for processing conditions
PHYSICAL PROPERTIES
| Property Typical Value* Test Method | ||
|---|---|---|
| Density | 955 kg/m³ | ISO 1183 |
| Melt Flow Rate (190°C/2.16kg) | 1.5 g/10min | ISO 1133 |
| Tensile Modulus (1mm/min) | 920 MPa | ISO 527-2 |
| Tensile Stress at Yield (50mm/min) | 24.0 MPa | ISO 527-2 |
| Tensile Strain at Yield (50mm/min) | 0.095 | ISO 527-2 |
| Tensile Stress at Break (50mm/min) | 14 MPa | ISO 527-2 |
| Tensile Strain at Break (50mm/min) | 4 | ISO 527-2 |
| Flexural modulus (2mm/min) | 980 MPa | ISO 178 |
| Charpy Notched Strength (23°C, 1eA, Edgewise) | 14.0 kJ/m² | ISO 179-1 |
| Shore Hardness (Shore D, 15 sec.) | 60 | ISO 868 |
| Shore Hardness (Shore D, 1 sec.) | 63.5 | ASTM D2240 |
| VICAT Softening Temperature (A50) | 125°C | ISO306 |
| VICAT Softening Temperature (B50) | 70°C | ISO306 |
| Temperature of deflection under load (DTUL) | 64°C | ISO 75-2 |
| ESCR (10% Igepal – F50) | 400 Hours | ASTM D1693-B |
| FNCT (2% Arkopal, 6.0Mpa, 50°C) | 40 Hours | ISO 16770 |
DESCRIPTION
FT6230 is a Low Density Polyethylene for Film extrusion produced by high pressure Tubular Technology. This grade is developed for the production of packaging film with good optical properties. FT6230 contains no additives.
PROCESSING GUIDELINES
FT6230 can be processed easily on most types of blown film equipment such as LDPE, LLDPE or HDPE extruders
Recommended processing conditions:
Melt temperature 160 –190°C
Die gap > 1.0 mm
FLH: > 2 DD
BUR: > 2:1
FOOD CONTACT REGULATIONS
FT6230 fulfils the food contact regulations in most countries. If required, contact your Borouge representative for a certificate.
STORAGE
The product should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product.
More information on storage can be found in Safety Information Sheet for this product
SAFETY
The product is not classified as a hazardous mixture.
Dust and fines from the product carry a risk of dust explosion. All equipment should be properly earthed. Inhalation of dust should be avoided as it may cause irritation of the respiratory system. Small amounts of fumes are generated during processing of the product. Proper ventilation is therefore required
A Safety Information Sheet is available on request. Please contact your Borouge representative for more details on various aspects of safety, recovery and disposal of the product.
RECYCLING
The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.
Andheri East, Mumbai, Maharashtra