This ultra-fine powder production line configuration meets customersreqirement for final product fineness between 325-1250 mesh.

• 1.Low investment and high efficiency.At the same fineness, HGM grinder is with lower power consumption, shorter recovery periodand 45% higher capacity than jet mill;
• 2.Wearing parts uses high-quality wear-resistant materials, expanding service life more than one year. And the final powder fineness can reach d975um;
• 3.There is not rolling bearing orbolt inside the grinding chamber, avoiding equipment damage caused by bearing damage or bolts looseness. It adopts high-efficiency pulse dust collector that effectively reduces dust pollution and makes better dust removal.

• Production capacity : 0.35-6T / H Note: this is an average value and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material : Powder grinding of limestone calcite fly ash calcium carbide desulfurization kaolin calcium carbonate coal gypsum slag powder bentonite barite marble talc refractories etc.
• Range of Application : Grinding processing of mineral materials in metallurgy building materials chemical mining etc.

This ultra-fine powder production line configuration meets customersreqirement for final product fineness between 325-1250 mesh.

After primary crushing by a small jaw crusher materials enter hammer crusher for a second crushingand then bucket elevator lifts the crushed material into hopper; screw conveyor conveys material from hopper into the HGM three-ring medium speed mill for grinding. Under the action of wind in the mill grinded material through the spout above into cyclone powder collector. In the collector most of powder will be separated from airflow and be collected. Trace amount of fine powder follows airflow into the pulse dust catcher. With this required fineness powder is gathered up and meanwhile air is purified by the dust catcher.

EMCC mobile construction waste crushing plant adopts the advanced construction waste treatment technology to crush construction waste, industrial waste, cinder, coal, rock, slag, fly ash, building materials, non-metallic solid waste and other waste into various new building materials in conformity with the quality inspection standard.

• 1.The frame structure adoptsfinite element analysis technology, with reasonable design, and excellent material;
• 2.It is professional construction waste crushing equipment, with larger feeding size and higher capacity;
• 3.The specially equipped iron separatoris with stronger magnetism. It can effectively remove steel and other ferrous metals away from the construction waste, ensuring the equipment service life;
• 4.The frame supporting legs with strongsiteadaptability can be adjusted according to site conditions.

• Production capacity : 10-500T / H Note: this is only an average value and the specific is subject to the clientsactual equipment configuration in site.
• Processable Material : Construction waste industrial waste cinder coal rock slag fly ash building rubbish materials
• Range of Application : Nonmetallic solid waste reprocessing

EMCC mobile construction waste crushing plant adopts the advanced construction waste treatment technology to crush construction waste, industrial waste, cinder, coal, rock, slag, fly ash, building materials, non-metallic solid waste and other waste into various new building materials in conformity with the quality inspection standard. Depending on different device configuration, the effective utilization of construction waste can reach 80-100%, with no secondary pollution. It can achieve near-zero pollution and zero emissions ideal environmental effects. The user can also select fixed building waste crushing production line according to the requirements of the construction.

Initially screened construction wastes were transported into the vortex impact crusher by a vibrator feeder then needless iron materials could be removed by magnetic separator in the course of transmission and finished product to be screened by a round vibrating sieve (1-4 layers freedom of choice). Unqualified coarse material returned eddy impact crusher for second crushing again.

MQX ultrafine ball mill powder production line is suitable for ultrafine powder final product with fineness of about 1250 mesh.

• 1.Reasonable inlet and outlet designimproves equipment production stability;
• 2.High manganese steel linerismore wear-resistant and with longer working life;
• 3.Theclosed cycle of productioncan ensure both fineness and production efficiency;
• 4.The equipment can independently complete the whole production process from raw material crushing equipment, transport, milling to the finished product collection, storage and packaging.
• 5.It canalso use special ball mill lining for special industryto get non-ferrous products.

• Production capacity : 0.5-15T / H Note: this is an average value and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material : Powder milling production of limestone calcite fly ash calcium carbide desulfurization kaolin calcium carbonate coal gypsum slag powder bentonite barite marble talc refractories etc.
• Range of Application : This powder production line is for grinding process of non-explosive and brittle materials with low hardness (Mohs hardness

YGMX ultrafine powder mill production line is suitable for processing materials with fineness of finished products in 325-1250 mesh.

• 1.With stable operation, the unique structure grading wheel equipped inside the hostmakes good grading effect, ideal particle size, stable product quality and no large particle contamination. It is currently ideal equipment of non-metallic mineral powder dry
• 2.The rollerand ring adopts special wear-resistant steel, achieving low wearing, long service life and easy maintenance and reducing downtime and replacement
• 3.The equipment can independently complete the whole production process from raw material crushing equipment, transport, milling to the finished product collection, storage and packaging.
• 4.Squirrel-cage classifier improvesgrading capabilities and efficiency.

• 0.4-18T / H Note: this is only an average value and the specific is subject to the clientsactual equipment configuration in site.
• Processable Material :Powder grinding process of limestone calcite fly ash calcium carbide desulfurization kaolin calcium carbonate coal gypsum slag powder bentonite barite marble talc refractories etc.
• Grinding processing of mineral materials and other more than 280 kinds of materials in metallurgy building materials chemical mining etc.

YGMX ultrafine powder mill production line is suitable for processing materials with fineness of finished products in 325-1250 mesh. The YGMX ultra-fine powder grinding mill does not only meet customer requirements for fineness, but also meets the big yield requirements of customers. It not only has the function of product improvement, but also pursues efficiency, reliability, stability, persistence, to help customers achieve long-term, stable income.

After crushed by hammer crusher materials enter into hopper through bucket elevator and then the material inside silo would be evenly taken into YGMX superfine grinding mill by the electromagnetic vibration feeder.Grinded materials enter KX high fine rotor type classifier through the upper spout under the action of windand the dust is purified by pulse dust collector also.

Finished products of sand and gravel production line include stones and artificial sand. In the production factory of road and building materials this production line is usually established.

• 1.Big crushing ratioand high capacity;
• 2.The produced aggregate is mostly reasonable cubic and low content of needle flake material. And the aggregate can be used for highway construction.
• 3.The artificialsand is with higher quality than natural
• 4.Wearing parts useshigh-strength wear-resistant materials to enable low loss and long service life.

• Production capacity : 10-500T / H Note: this is only an average value and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material : Sand making process of limestone granite marble basalt iron ore river pebble shale bluestone coal cobblestone construction waste
• Range of Application : Mining smelting building material highway railway water conservancy and chemical industry and other industries

Finished products of sand and gravel production line include stones and artificial sand. In the production factory of road and building materials, this production line is usually established.

Raw material is screened and carried by vibrating feeder which conveys large material into jaw crusher equably for primary crushing. Crushed material would be transported by belt conveyor into WKS Symons cone crusher for fine crushing and then materials enter into circular vibrating screen by belt conveyor for screening to distinguish the different specifications of finished product and unqualified gravel would be conveyed into cone crusher to be crushed again.

Symons stone crushing production plant configuration is suitable for crushing high hardness stone with finished particle size 3mm-64mm. The particle size can be adjusted according to need.

1. 1.Bigcrushingratioandhighcapacity;
2. 2.Itadoptssteelframeinsteadofconcretefoundation, makinginstallationeasyandquickandappearanceWhenyouneedtomovetobetterproductionsite, thesteelframecanalsobesecondaryused.
3. 3.Wearingpartsuseshigh-strengthwear-resistantmaterialstoenablelowlossandlongservice

• Production capacity :27-600T / H Note: this is only a average number and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material :Gravel crushing process of limestone granite marble basalt iron ore river pebble shale bluestone coal cobblestone construction waste
• Range of Application :metallurgy construction water & electricity transportation chemical industry building materials industry

Symons stone crushing production plant configuration is suitable for crushing high hardness stone with finished particle size 3mm-64mm. The particle size can be adjusted according to need. WKS Symons cone crusher developed by EMCC meets customersproduction reqirements and there are two specifications of standard and short head type. Our equipments always pursues efficiency, reliability, stability, durability to help customers achieve long-term an stable income.

Raw materials are screened and carried by vibrating feeder which conveys large materials into jaw crusher equably for primary crushing. Crushed materials will be transported by belt conveyor into WKS Symons cone crusher for fine crushing and then materials enter into circular vibrating screen for screening to distinguish the different specifications of finished product and unqualified gravel will be conveyed into cone crusher to be crushed again.

Sand making line usually merges Vibrating Feeder Jaw Crusher Straight Impact Crusher (Sand Making Machine) Vibrating Screen Sand Washer Belt Conveyor and Centered electric control cabinet into a single whole.

• 1.Bigcrushingratio andhighcapacity;
• 2.Theproducedaggregateismostlyreasonablecubicandlowcontentofneedleflakematerial.Andtheaggregatecanbeusedforhighwayconstruction.
• 3.Theartificialsandiswithhigherqualitythannatural
• 4. Wearingpartsuseshigh-strengthwear-resistantmaterialstoenablelowlossandlongservicelife.

• Production capacity : 70-600T/h Note: this is only a average number and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material : Sand making&washing line for processing limestone river gravel rocks bluestone pebbles weathered sand basalt granite quartz silica diabase
• Range of Application : All kinds of metal and nonmetal mines cement refractory materials abrasives glass raw materials construction aggregate sand mechanism metallurgy etc.

Sand making line usually merges Vibrating Feeder, Jaw Crusher, Straight Impact Crusher (Sand Making Machine), Vibrating Screen, Sand Washer, Belt Conveyor and Centered electric control cabinet into a single whole. Designed capacity is generally 50-500T/h.Experiencing several years of research and development, the whole set of sand production line , which we combined Straight Impact Crusher under advanced international level with other ancillary products to develop, is leading the line.

Vibrating Feeder equably puts raw material into Jaw Crusher then belt conveyor puts unfinished products into sand making machine for further crushing and the unfinished products which achieve the final requirement size are put into sand washer after Vibrating Screens separating. The cleaned products are the final products.The unfinished products which do not achieve the final requirement size will be reprocessed in sand making machine which forms circulatory system.The output size is changed by owners needs. If you choose dried production process it should cooperate with powder separator and dust removal equipment.

The customer is a dealer, he visited our company twice, and visited some of our crushing plants in our domestic market, he is very happy with our service and quality, bought the crusher from us, after one year, he bought a grinding mill from us, we built long business relationship.

A mining company in Indonesia contacted with us, their company plan to build a calcium carbonate factory. Our company according to their requires and configure a set of production line for them

The customer get a contact information of us, then came to us and visited some of our grinding mill operation site in our domestic market, after a long time negotiation, he think our YGMX130 grinding mill is the best choice.

Main coal powder production equipment in this project is a star product of our company -YGM130 high-pressure medium speed mill. Fineness of finished powder is even, which increases combustion efficiency in coal powder boilers, raises production and reduces the pollutant emissions.

The traditional iron ore crusher is of the low production efficiency and poor wear resistance, which affects the production schedule. After customers purchase this set of iron ore crushing production line equipment, not only the production efficiency is greatly improved, but also fittings are very wear-resisting.

This ultra-fine powder production line configuration meets customersreqirement for final product fineness between 325-1250 mesh.

• 1.Low investment and high efficiency.At the same fineness, HGM grinder is with lower power consumption, shorter recovery periodand 45% higher capacity than jet mill;
• 2.Wearing parts uses high-quality wear-resistant materials, expanding service life more than one year. And the final powder fineness can reach d975um;
• 3.There is not rolling bearing orbolt inside the grinding chamber, avoiding equipment damage caused by bearing damage or bolts looseness. It adopts high-efficiency pulse dust collector that effectively reduces dust pollution and makes better dust removal.

• Production capacity : 0.35-6T / H Note: this is an average value and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material : Powder grinding of limestone calcite fly ash calcium carbide desulfurization kaolin calcium carbonate coal gypsum slag powder bentonite barite marble talc refractories etc.
• Range of Application : Grinding processing of mineral materials in metallurgy building materials chemical mining etc.

This ultra-fine powder production line configuration meets customersreqirement for final product fineness between 325-1250 mesh.

After primary crushing by a small jaw crusher materials enter hammer crusher for a second crushingand then bucket elevator lifts the crushed material into hopper; screw conveyor conveys material from hopper into the HGM three-ring medium speed mill for grinding. Under the action of wind in the mill grinded material through the spout above into cyclone powder collector. In the collector most of powder will be separated from airflow and be collected. Trace amount of fine powder follows airflow into the pulse dust catcher. With this required fineness powder is gathered up and meanwhile air is purified by the dust catcher.

EMCC mobile construction waste crushing plant adopts the advanced construction waste treatment technology to crush construction waste, industrial waste, cinder, coal, rock, slag, fly ash, building materials, non-metallic solid waste and other waste into various new building materials in conformity with the quality inspection standard.

• 1.The frame structure adoptsfinite element analysis technology, with reasonable design, and excellent material;
• 2.It is professional construction waste crushing equipment, with larger feeding size and higher capacity;
• 3.The specially equipped iron separatoris with stronger magnetism. It can effectively remove steel and other ferrous metals away from the construction waste, ensuring the equipment service life;
• 4.The frame supporting legs with strongsiteadaptability can be adjusted according to site conditions.

• Production capacity : 10-500T / H Note: this is only an average value and the specific is subject to the clientsactual equipment configuration in site.
• Processable Material : Construction waste industrial waste cinder coal rock slag fly ash building rubbish materials
• Range of Application : Nonmetallic solid waste reprocessing

EMCC mobile construction waste crushing plant adopts the advanced construction waste treatment technology to crush construction waste, industrial waste, cinder, coal, rock, slag, fly ash, building materials, non-metallic solid waste and other waste into various new building materials in conformity with the quality inspection standard. Depending on different device configuration, the effective utilization of construction waste can reach 80-100%, with no secondary pollution. It can achieve near-zero pollution and zero emissions ideal environmental effects. The user can also select fixed building waste crushing production line according to the requirements of the construction.

Initially screened construction wastes were transported into the vortex impact crusher by a vibrator feeder then needless iron materials could be removed by magnetic separator in the course of transmission and finished product to be screened by a round vibrating sieve (1-4 layers freedom of choice). Unqualified coarse material returned eddy impact crusher for second crushing again.

MQX ultrafine ball mill powder production line is suitable for ultrafine powder final product with fineness of about 1250 mesh.

• 1.Reasonable inlet and outlet designimproves equipment production stability;
• 2.High manganese steel linerismore wear-resistant and with longer working life;
• 3.Theclosed cycle of productioncan ensure both fineness and production efficiency;
• 4.The equipment can independently complete the whole production process from raw material crushing equipment, transport, milling to the finished product collection, storage and packaging.
• 5.It canalso use special ball mill lining for special industryto get non-ferrous products.

• Production capacity : 0.5-15T / H Note: this is an average value and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material : Powder milling production of limestone calcite fly ash calcium carbide desulfurization kaolin calcium carbonate coal gypsum slag powder bentonite barite marble talc refractories etc.
• Range of Application : This powder production line is for grinding process of non-explosive and brittle materials with low hardness (Mohs hardness

YGMX ultrafine powder mill production line is suitable for processing materials with fineness of finished products in 325-1250 mesh.

• 1.With stable operation, the unique structure grading wheel equipped inside the hostmakes good grading effect, ideal particle size, stable product quality and no large particle contamination. It is currently ideal equipment of non-metallic mineral powder dry
• 2.The rollerand ring adopts special wear-resistant steel, achieving low wearing, long service life and easy maintenance and reducing downtime and replacement
• 3.The equipment can independently complete the whole production process from raw material crushing equipment, transport, milling to the finished product collection, storage and packaging.
• 4.Squirrel-cage classifier improvesgrading capabilities and efficiency.

• 0.4-18T / H Note: this is only an average value and the specific is subject to the clientsactual equipment configuration in site.
• Processable Material :Powder grinding process of limestone calcite fly ash calcium carbide desulfurization kaolin calcium carbonate coal gypsum slag powder bentonite barite marble talc refractories etc.
• Grinding processing of mineral materials and other more than 280 kinds of materials in metallurgy building materials chemical mining etc.

YGMX ultrafine powder mill production line is suitable for processing materials with fineness of finished products in 325-1250 mesh. The YGMX ultra-fine powder grinding mill does not only meet customer requirements for fineness, but also meets the big yield requirements of customers. It not only has the function of product improvement, but also pursues efficiency, reliability, stability, persistence, to help customers achieve long-term, stable income.

After crushed by hammer crusher materials enter into hopper through bucket elevator and then the material inside silo would be evenly taken into YGMX superfine grinding mill by the electromagnetic vibration feeder.Grinded materials enter KX high fine rotor type classifier through the upper spout under the action of windand the dust is purified by pulse dust collector also.

Finished products of sand and gravel production line include stones and artificial sand. In the production factory of road and building materials this production line is usually established.

• 1.Big crushing ratioand high capacity;
• 2.The produced aggregate is mostly reasonable cubic and low content of needle flake material. And the aggregate can be used for highway construction.
• 3.The artificialsand is with higher quality than natural
• 4.Wearing parts useshigh-strength wear-resistant materials to enable low loss and long service life.

• Production capacity : 10-500T / H Note: this is only an average value and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material : Sand making process of limestone granite marble basalt iron ore river pebble shale bluestone coal cobblestone construction waste
• Range of Application : Mining smelting building material highway railway water conservancy and chemical industry and other industries

Finished products of sand and gravel production line include stones and artificial sand. In the production factory of road and building materials, this production line is usually established.

Raw material is screened and carried by vibrating feeder which conveys large material into jaw crusher equably for primary crushing. Crushed material would be transported by belt conveyor into WKS Symons cone crusher for fine crushing and then materials enter into circular vibrating screen by belt conveyor for screening to distinguish the different specifications of finished product and unqualified gravel would be conveyed into cone crusher to be crushed again.

Symons stone crushing production plant configuration is suitable for crushing high hardness stone with finished particle size 3mm-64mm. The particle size can be adjusted according to need.

1. 1.Bigcrushingratioandhighcapacity;
2. 2.Itadoptssteelframeinsteadofconcretefoundation, makinginstallationeasyandquickandappearanceWhenyouneedtomovetobetterproductionsite, thesteelframecanalsobesecondaryused.
3. 3.Wearingpartsuseshigh-strengthwear-resistantmaterialstoenablelowlossandlongservice

• Production capacity :27-600T / H Note: this is only a average number and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material :Gravel crushing process of limestone granite marble basalt iron ore river pebble shale bluestone coal cobblestone construction waste
• Range of Application :metallurgy construction water & electricity transportation chemical industry building materials industry

Symons stone crushing production plant configuration is suitable for crushing high hardness stone with finished particle size 3mm-64mm. The particle size can be adjusted according to need. WKS Symons cone crusher developed by EMCC meets customersproduction reqirements and there are two specifications of standard and short head type. Our equipments always pursues efficiency, reliability, stability, durability to help customers achieve long-term an stable income.

Raw materials are screened and carried by vibrating feeder which conveys large materials into jaw crusher equably for primary crushing. Crushed materials will be transported by belt conveyor into WKS Symons cone crusher for fine crushing and then materials enter into circular vibrating screen for screening to distinguish the different specifications of finished product and unqualified gravel will be conveyed into cone crusher to be crushed again.

Sand making line usually merges Vibrating Feeder Jaw Crusher Straight Impact Crusher (Sand Making Machine) Vibrating Screen Sand Washer Belt Conveyor and Centered electric control cabinet into a single whole.

• 1.Bigcrushingratio andhighcapacity;
• 2.Theproducedaggregateismostlyreasonablecubicandlowcontentofneedleflakematerial.Andtheaggregatecanbeusedforhighwayconstruction.
• 3.Theartificialsandiswithhigherqualitythannatural
• 4. Wearingpartsuseshigh-strengthwear-resistantmaterialstoenablelowlossandlongservicelife.

• Production capacity : 70-600T/h Note: this is only a average number and the specific value is subject to the clientsactual equipment configuration in site.
• Processable Material : Sand making&washing line for processing limestone river gravel rocks bluestone pebbles weathered sand basalt granite quartz silica diabase
• Range of Application : All kinds of metal and nonmetal mines cement refractory materials abrasives glass raw materials construction aggregate sand mechanism metallurgy etc.

Sand making line usually merges Vibrating Feeder, Jaw Crusher, Straight Impact Crusher (Sand Making Machine), Vibrating Screen, Sand Washer, Belt Conveyor and Centered electric control cabinet into a single whole. Designed capacity is generally 50-500T/h.Experiencing several years of research and development, the whole set of sand production line , which we combined Straight Impact Crusher under advanced international level with other ancillary products to develop, is leading the line.

Vibrating Feeder equably puts raw material into Jaw Crusher then belt conveyor puts unfinished products into sand making machine for further crushing and the unfinished products which achieve the final requirement size are put into sand washer after Vibrating Screens separating. The cleaned products are the final products.The unfinished products which do not achieve the final requirement size will be reprocessed in sand making machine which forms circulatory system.The output size is changed by owners needs. If you choose dried production process it should cooperate with powder separator and dust removal equipment.

The customer is a dealer, he visited our company twice, and visited some of our crushing plants in our domestic market, he is very happy with our service and quality, bought the crusher from us, after one year, he bought a grinding mill from us, we built long business relationship.

A mining company in Indonesia contacted with us, their company plan to build a calcium carbonate factory. Our company according to their requires and configure a set of production line for them

The customer get a contact information of us, then came to us and visited some of our grinding mill operation site in our domestic market, after a long time negotiation, he think our YGMX130 grinding mill is the best choice.

Main coal powder production equipment in this project is a star product of our company -YGM130 high-pressure medium speed mill. Fineness of finished powder is even, which increases combustion efficiency in coal powder boilers, raises production and reduces the pollutant emissions.

The traditional iron ore crusher is of the low production efficiency and poor wear resistance, which affects the production schedule. After customers purchase this set of iron ore crushing production line equipment, not only the production efficiency is greatly improved, but also fittings are very wear-resisting.