Antique Designer Tiles

Rafaleshwar, Morbi, Gujarat

antique tile grout silver is a fine powder consisting of portland cement, specially selected polymer, properly selected & graded fine fillers, additives and inorganic chemicals. It is used for grouting of tiles, stones, marble joints & edges because it has water repellency properties, excellent adhesion (high bonding strength), soft consistency, workability and seals joint permanently. It is non-shrinking, non-toxic and odourless grout used for sealing of swimming pool & water tank joints as well.

areas of application

antique tile grout silver is used for grouting of ceramic tiles, marbles, natural stones and edges.*specially formulated for wet or submerged grouting applications such as swimming pool, bathrooms, toilets, fountains and kitchen areas.*it can be used for external and internal areas.*it is used in residential and commercial areas.*application up to joint width of 2-4mm.*it is excellent for highly glazed tiles to give a smooth and watertight joints which when set will be both waterand mould resistant.

features & benefits

*aesthetics available in specify shades.*easy to use easily to mix with water and forms soft consistency paste which is easy to fill the joints.*shrinkage & cracking avoids cracks formation in the joints and also there is negligible shrinkage.*service temperature specially formulated for temperature range of 5 120c.* water resistant excellent water-resistance making it beneficial for application in areas immersed underwater.* durability & uv resistant excellent uv resistance & durability enables the product use for exteriorapplication.* high strength & abrasion resistant high strength & abrasion resistance properties makes it suitablefor grouting of toilets & bathrooms.

method of application

1 surface preparation* surface must be cleaned and should be free from dirt, cured tile adhesive. Remove dust with wire brush & by air blower.* for exterior grouting application, wet the tiles prior to applying antique tile grout silver. 2 mixing* add the grout powder to the mixing water (w:p ratio 1 : 2.5 by volume) and mix with slow speed drill (250-300 rpm) to a soft & smooth consistency paste.* if the grout mortar has become too stiff to work, it should be discarded and a new batch should be prepared. 3 application

apply to the tile joints with squeegee, spatula or putty blade. After application flush the surface of tile using a hard rubber float, working diagonally across the grout joints to fill and compact the joints. All excess grout should be removed with the same rubber float without any delay.*lesser the quantity of grout left on the face of the tiles while application, the final cleaning will be easier. With antique tiles & grout cleaner 225.*however, it is important to allow the grout to set in the joint and to let it acquire its initial set before any further cleaning. After the initial set of the grout, clean the tile surface with a pad of cheesecloth or towel dampened with minimum quantity of clean and cool water. Rub in a circular motion to further compact the grout.*the remaining surface grout on the tile can also be cleaned at this time. Scrubbing pad fastened to a float works very well to remove grout from the porous tiles.*rebuff the tile surface and grout within 1-2 hours to remove all weep water and grout residue from the surface, which helps to reduce the efflorescence and to control colour variation.

4 cleaning*polish the tiles when the job is complete with a clean dry cloth. Scrubbing the floor with hot water and soap water is the best.*due to polymer content, it is advisable to clean the surface immediately after the grouting.

precautions & limitations*do not mix excess water.*antique tile grout silver cannot be used where high acid resistance is required because of its cement base.*the potential for efflorescence is inherent in all cement-based products and it is not to be considered as a manufacturing defect.

Antique Tile Grout Golden is a High Polymer based fine powder consisting of portland cement, specially selected polymer, properly selected & graded fine fillers, additives and inorganic chemicals. It is used forgrouting of tiles, stones, marble joints & edges because it has water repellency properties, excellent adhesion (high bonding strength), soft consistency, workability and seals joint permanently. It is nonshrinking, non-toxic and odourless grout used for sealing of swimming pool & water tank joints as well.

Areas of Application

Antique Tile Grout Golden is used for grouting of ceramic tiles, marbles, natural stones and edges.

*Specially formulated for wet or submerged grouting applications such as swimming pool, bathrooms, toilets, fountains and kitchen areas.*It can be used for external and internal areas.*It is used in residential and commercial areas.*Application up to joint width of 2-10mm.*It is excellent for highly glazed tiles to give a smooth and watertight joints which when set will be both water and mould resistant.

Features & Benefits

*Aesthetics Available in specify shades.*Easy to use Easily to mix with water and forms soft consistency paste which is easy to fill the joints.*Shrinkage & cracking Avoids cracks formation in the joints and also there is negligible shrinkage.*Service Temperature Specially formulated for temperature range of 50 1500C.* Water resistant Excellent water-resistance making it beneficial for application in areas immersed under water.* Durability & UV resistant Excellent UV resistance & durability enables the product use for exterior application.* High Strength & abrasion resistant High strength & abrasion resistance properties makes it suitable for grouting of toilets & bathrooms.

Method of Application

1 Surface Preparation* Surface must be cleaned and should be free from dirt, cured tile adhesive. Remove dust with wire brush & by air blower.* For exterior grouting application, wet the tiles prior to applying Antique Tile Grout Golden 2 Mixing* Add the grout powder to the mixing water (w:p ratio 1 : 2.5 by volume) and mix with slow speed drill (250-300 rpm) to a soft & smooth consistency paste.* If the grout mortar has become too stiff to work, it should be discarded and a new batch should be prepared. 3 ApplicationApply to the tile joints with squeegee, spatula or putty blade. After application flush the surface of tile using a hard rubber float, working diagonally across the grout joints to fill and compact the joints. All excess groutshould be removed with the same rubber float without any delay.

*Lesser the quantity of grout left on the face of the tiles while application, the final cleaning will be easier with Antique Tiles & Grout Cleaner 225.*However, it is important to allow the grout to set in the joint and to let it acquire its initial set before any further cleaning. After the initial set of the grout, clean the tile surface with a pad of cheesecloth or towel dampened with minimum quantity of clean and cool water. Rub in a circular motion to further compact the grout.*The remaining surface grout on the tile can also be cleaned at this time. Scrubbing pad fastened to a float works very well to remove grout from the porous tiles.*Rebuff the tile surface and grout within 1-2 hours to remove all weep water and grout residue from the surface, which helps to reduce the efflorescence and to control colour variation. 4 CLEANING*Polish the tiles when the job is complete with a clean dry cloth. Scrubbing the floor with hot water and soap water is the best.*Due to polymer content, it is advisable to clean the surface immediately after the grouting.

Precautions & Limitations*Do not mix excess water.*Antique Tile Grout Golden cannot be used where high acid resistance is required because of its cement base.*The potential for efflorescence is inherent in all cement-based products and it is not to be considered as a manufacturing defect.

Single component Polymer modified Bituminous Waterproof Coating.

DESCRIPTION

Antique Seal 115 is composed of viscous, polymer modified, mineral fillers, additives and water as a medium.It is used as a waterproof & weatherproof membrane for concealed roofs, walls of the building structures because it forms relatively thick film and bonds firmly to cementitious surfaces, protects wood & timber andprevents rust formation. Waterproofing is achieved by applying Antique Seal 115 by brush or mop. It forms joint less and seamless membrane.

Areas of Application

Waterproofing of concealed roofs, wall, water tank, swimming pool, *Corrosion protection for concrete from sea water.

Features & Benefits

* Waterproofing Exceptionally good waterproofing.*Ease of application Cold applied, bituminous emulsion material. Easily applied by brush or mop.* Durability Forms relatively thick (1.2-1.5 mm) film providing excellent impermeable and durable membrane.* Movement accommodation Polymer modified hence forms flexible film. Also accommodates thermal stresses in slab due to variation in temperature.* Reinforcement Higher reinforcement can be induced with polyester fibre sheet between the coats.* Self priming No separate or additional primer is required.

Method of Application 1 SURFACE PREPARATION*Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc.*Mechanical means such as wire brushing & shot blasting can be used.*Finally vacuum cleaning of all loose solids and liquids can be done if required.*All surface cracks up to 5 mm width should be filled up with Antique Non Shink Crack-x.Cracks more than 5 mm and all separation gaps should be filled up with Antique Flexi Bond URP Modified Adhesive as specified.

2 APPLICATION* Apply Three coats directly by brush or mop and dilute Antique Seal 115 with three part of water & one part of Antique Seal 115 powder.* Apply 2nd & 3rd coat in gapes of two or three hours.

3 CLEANING Tools & equipments should be cleaned with potable water immediately after use. Cured material can be cleaned by scrapping

Antique Cem Bond/Super Bondis specially formulated integral liquid waterproofing compound composed of surface activePlasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation. Areas of Application Waterproofing of concrete and sand-cement mortars used in

*Basements* Roof slabs and screeds* Water tanks & water retaining structures* External plastering* Bathrooms and balconies* Sumps and drains

Features & Benefits

* Corrosion resistant Makes concrete more cohesive, hence protects steel better against corrosion* Compatibility Being a liquid, easily dispersible & compatible with concrete/mortar mixes.* Permeability It reduces the permeability of water into concrete.* Strength The setting time and compressive strength of the concrete remains within the specification limits.* Shrinkage Reduces shrinkage crack development in plaster & concrete.* Workability Improves workability of freshly mixed cement concrete.* Durability Increases durability by improving waterproofing of concrete.

Method of Application

* Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 12 minutes.* Start addition of 7580% mixing water & mix for 2-3 minutes.* Antique Cem Bond AW+111 is added as per the recommended dosage into the remaining mixing / gauging water, then add to concrete mixer & mix for another 2 minutes.* Place the concrete or apply plaster, as needed .* Cure the applied mortar or concrete as per good construction practices.

Precautions & Limitations*Do not add Antique Cem Bond AW+111 directly to dry cement & aggregate mix.* Maintain water-cement ratio as low as possible.* Do not increase the dosage of Antique Cem Bond AW+111 than the recommendation.

Antique Wall Mortar is a water resistant Luster wall coating for interior as well as exterior use. Antique Wall Mortar make building components totally water proof.Antique Wall Mortar is totally crack proof with high bonding which gives colour resistancy as well as weather proofing. Get luster finishwith UV resistance & eco friendly with high bond luster coating.

Salient features of Antique Wall Mortar*Make building component Totally Water*Made wall totally crackproof with high bonding.*Colour resistancy as well as Weatherproofing.*Use for interior as well as exterior coating.*Get Luster Finish With UV Resistance and Eco friendlyAntique Wall Mortar

Application ProcedureRemove all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and clean water. The substrate should be clean, free from dust, grease and loose materials.Dry and absorbent surfaces should be moistened with sufficient quantity of clean water.Mix Antique Wall Mortar with 60-65% clean water slowly to make paste. Continue the mixing for 10-15 minutes with putty grind machine till a uniform paste is formed. After thoroughly mixing Antique Wall Mortar apply the first coat with Antique base mortar on already moistened wall surface from bottom to upward direction uniformly with the help of putty blade. This would ensure less wastage and proper finish. After drying of first coat of Antique base mortar just rub the surface gently with west sponge or rub the surface very gently with the putty blade in order to remove the loose particles. Allow the surface to dry for atleast 24 hours and then apply second coat of with Antique finish mortar Leave the surface to dry completely. After drying of second coat remove marks if any with the help of moist sponge or rub the surface very gently with the putty blade. Leave the surface to dry preferably for overnight. Always prepare a required quantity of putty and use it within 2-3 hrs. of mixing with water The total thickness of the coats should be limited to maximum 1.5mm. It is not essential to rub the surface done with Antique Wall Mortar, however if you need to remove unevenness before applying any kind of paint/distemper, gently level the walls/ceiling surface with very fine water proof emery paper of not less that 500 number to get a glossy white surface.

Precautions During ApplicationMixing of Antique Wall Mortar is very important and hence extreme care is to be taken for proper and thorough mixing with hand or mechanical stirrer in order to get best results. Antique Wall Mortar should be done over fully cured surface. It is recommended not to rub Antique Wall Mortar strongly and harshly with rough emery paper. This breaks the film formed over Antique Wall Mortar, which decreases the water repellency properties. The total thickness of the coat should be limited to maximum 1.5mm. In case of fresh concrete/mortar surface it is recommended that two coats of Antique Base Mortar be apply before application of Antique Wall Mortar.

CoverageThe coverage area of Antique Base Wall Mortar on smooth normal mortar wall is 25 to 30 Sq. Ft/Kg/mmThe coverage area of Antique Finish Wall Mortar on smooth normal mortar wall is 35 to 40 Sq. Ft/Kg/mmThe coverage area, however, will depend upon the quality of the substrate.

NoteGenerally the cause of efflorescence on the walls surface is the brick masonry, which is due to the quality of bricks, sand and water, If the effect of efflorescence on the brick masonry seems to be very high then proper care should be taken to control the efflorescence. The efflorescence problem on brick masonry if exists impairs the bonding of Antique Wall Mortar as is with any other product.* for High Effected efflorescence walls Contact our Customer Care for solution.

Packing Antique Base Wall Mortar is available in 20Kg Pack.

Antique Finish Wall Mortar is available in 10Kg Box Pack.

Antique Wall Putty is a water resistant white cement based putty ideal for use on concrete/mortar walls (Internal and External) and ceilings. It fills the fine pores of mortar/concrete walls and ceilings and provides a white, smooth and dry surface, essential for painting. Antique Wall Putty can be applied even on moist surface (Internal/External). Antique Wall Putty has more adhesive strength, durability and enhances the life of paints. Antique Wall Putty though white cement based, does not require water curing.

Salient features of Antique Wall Putty

Being a cementitious material it has better adhesiveness and durability. Antique Wall Putty can be applied on both interior and exterior surfaces. Antique Wall Putty does not require any curing.It is water resistant and can be applied on moist surface. It is recommended that two coats of BirlaWhite cement wash be done before application of Antique Wall Putty. Antique Wall Putty gives a smooth and glossy finish.Any kind of paint or distemper can be applied on it.No need to apply any kind of primer on it before application of paint/distemper.It can be applied on used surface after proper preparation.It prevents the growth of algae and fungi on walls.It is in dry powder form and does not produce any kind of unpleasant smell at the time of application.

Application Procedure

Remove all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and clean water. The substrate should be clean, free from dust, grease and loose materials. Dry and absorbent surfaces should be moistened with sufficient quantity of clean water.

Mix Antique Wall Putty with 30-35% clean water slowly to make paste. Continue the mixing for 10-15 minutes till a uniform paste is formed. After thoroughly mixing Antique Wall Putty apply thefirst coat on already moistened wall surface from bottom to upward direction uniformly with the help of putty blade. This would ensure less wastage and proper finish. After drying of first coat of putty just rubthe surface gently with west sponge or rub the surface very gently with the putty blade in order to remove the loose particles. Allow the surface to dry for atleast 3 hours and then apply second coat of putty. Leavethe surface to dry completely. After drying of second coat remove marks if any with the help of moist sponge or rub the surface very gently with the putty blade. Leave the surface to dry preferably for overnight. Always prepare a required quantity of putty and use it within 2-3 hrs. of mixing with water The total thickness of the coats should be limited to maximum 1.5mm. It is not essential to rub the surface done with Antique Wall Putty, however if you need to remove unevenness before applying any kind of paint/distemper, gently level the walls/ceiling surface with very fine water proof emery paper of not less that 500 number to get a glossy white surface.

Precautions During ApplicationMixing of Antique Wall Putty is very important and hence extreme care is to be taken for proper and thorough mixing with hand or mechanical stirrer in order to get best results. Antique Wall Puttyshould be done over fully cured surface. It is recommended not to rub Antique Wall Putty strongly and harshly with rough emery paper. This breaks the film formed over Antique Wall Putty, whichdecreases the water repellency properties. The total thickness of the coat should be limited to maximum 1.5mm. In case of fresh concrete/mortar surface it is recommended that two coats of Birla White cementwash be done before application of Antique Wall Putty.

CoverageThe coverage area of Antique Wall Putty on smooth normal mortar wall is 20 to 25 Sq. Ft/Kg/mm in double coat. The coverage area, however, will depend upon the quality of the substrate. NoteGenerally the cause of efflorescence on the walls surface is the brick masonry, which is due to the quality of bricks, sand and water, If the effect of efflorescence on the brick masonry seems to be very high then propercare should be taken to control the efflorescence. The efflorescence problem on brick masonry if exists impairs the bonding of Antique Wall Putty as is with any other product.

Packing Antique Wall Putty is available in 1Kg, 20Kg And 40Kg Packs.

Antique Non Shrink Filler is a cement based polymer modified powder material for filling cracks in plastered surface. It is composed of cement, select aggregates, polymer & additives which requires on site addition of water only.

Antique Designer Tiles is a widely prominent and popular name in the field of manufacturing and supplying varied collections of Decorative Tiles in India.

Antique Designer Tiles is a widely prominent and popular name in the field of manufacturing and supplying varied collections of Elevation Tiles in India.

Antique Adhesive Silver (Grey) is composed of ordinary portland cement properly selected & gradedaggregates, polymer, rheology modifier & additives. It is used for fixing of tiles internally & externally floorsbecause it gives excellent bond on cementitious surfaces like, concrete, plaster, etc. It forms a waterproof barrierbetween two surfaces and has excellent grab properties of tiles to the substrate.

Wall Putty is a water resistant white cement based putty ideal for use on concretemortar walls (Internal and External) and ceilings. It fills the fine pores of mortarconcrete walls and ceilings and provides a white, smooth and dry surface, essential for painting.

Antique Wall Mortar is a water resistant Luster wall coating for interior as well as exterior use.components totally water proof. Antique Wall Mortar is totally crack proof with high bonding which gives colour resistancy as well as weather proofing.

Fast acting, concentrated wall and floor tile cleaners with antibacterial performance for tiled surfaces. The special formulation removes dirt, grease and stains from tiled surfaces. When dry, the surface is left hygiencially clean. Suitable for all types of ceramic tiles, slate, stone, marble & terrazzo.