Our Products
Heating Elements
2 Products availableThermocouple
2 Products availableHeaters, Thermostats & Heating Devices
2 Products availableCeramic & Clay Crafts
1 Products availableWe are leaders in the market for providing best range of BTH Heaters
K Type Thermocoupleis the most common type of thermocouple. It is reliable, inexpensive, and accurate and its temperature range is wide. It is mostly used in nuclear applications due to the relative radiation hardness. The maximum temperature (continuous) is nearly 1, 100C.
These types of thermocouples are used widely in the industry. They have very good resistance to oxidation and high thermopower. They provide us withcorrect temperature monitoring in the range between -200C and 1370C (-328F to 2498F). They consist of nickel-5% aluminum and silicon (-) wire vs. nickel-10% chromium (+) wire. One should use this kind of thermocouple in oxidizing or inert atmospheres.The heating elementlikeelectric heatersis the best source to heat it up.
They are mostly used at temperatures over 540C (1004F) because of the higheroxidation resistance as compared to J, T or E types of thermocouples.
The range of K Type Thermocouple :
Extension wire Between 32 F and 392 F (0C to 200C)
Thermocouple grade wire Between 454 F and 2, 300 F (270C to 1260C)
Accuracy (which will be greater) :Special Limits of Error +/- 1.1C or 0.4%
Standard +/- 2.2C or +/- .75%
Names of Elements :
For describing the positive element of this type of thermocouple (KP), following names can be used: ThermoKanthal-KPs, HAI-KP1, Tophel+, Nickel-chrome, Chromel2, and T-13.
The negative element of this type of thermocouple (KN), is described by these names: ThermoKanthal-KNs, HAI-KN1, T-2s, Nial+, Nickel-silicon, and Alumel2.
Cautions to Take:
Some conditions should be avoided while usingthis type ofK thermocouple. It should not be used in vacuum applications because of the vaporization of chromium in the positive element. Also, it is not supposed to be used in the sulphurous environment as both of the elements will corrode rapidly and eventually the negative element will fail mechanically because of being brittle.
One should also avoid reducing atmospheres. The green-rot phenomenon can be caused due to low oxygen levels. In this phenomenon, chromium in elements will start oxidizing which cause very large negative drifts in calibration.
Take a look here as well, actually, If you are a wholesaler then you can have direct contact to thermocouple manufacturers near your area for bulk order.
Type K Thermocouplesare specified at the time whenmetallurgywas not as advanced as it is nowadays. As a result, the characteristics can vary extensively between samples. Nickel which is the constituent metal of K type thermocouple is magnetic. Thermocouples made with magnetic material have a characteristic that they are subjected to a deviation in output whenever the Curie point is reached by the material. This happens withthermocouple type kat nearly 185C.
Hope you like the content and him information given by us. If still have any query about the product or anything then dont forget to contact us.
FEATURE:-
Product Details:
Minimum Order Quantity:6 Piece
Power(Watts):As per requirement of application
Voltage:As per requirement of application
Size:As per requirement of application
Furnace heaters
Furnace Heater or electric furnace heater are very enclosed device which is used for high-temperature heating, is derived from a Greek word Fornax which ultimately means oven. There is much difference of heater such as electric heater, industrial chemical heater etc. Out of these types of heater, furnace heater is used for power generation, garbage disposal and applicable in oil and gas industry.
Quartz heaterare also available in the market, which are very useful in the winter season.
There are 2 types of furnace heater i.e. Natural gas or Propane gas wall furnace heater which could be used with a cabinet-mounted thermostat.
Furnace heater or electric heater can be installed within the wall or surface mounted on the exterior wall which varies horizontally through the wall. There are many models available online based on heat capacity, material and their temperature ranges.
A furnace heater works by blowing heated air through the ducts which deliver the warm air to rooms throughout the house via air registers or grills. This heating system is known as forced air distribution system or ducted warm air system which is powered by the electricity, natural gas or fuel.
Furnace heaters are the very useful appliance for the peoples who live in cold region. Normally, a home furnace is divided into 3 parts i.e. Burners, heat exchanger, vent and draft inducer. It is a forced air heating system which is used when the indoor air temperature is less than the temperature settled on the thermostat.
The required size and heating capacity of furnace heater depends upon the room size. If the size of your room is large, then you need to add the heating capacity of your furnace heater so that you could feel the warmth of the home.
While using furnace heater, condensing furnaces are designed to reclaim escaping heat well below than 140F where water vapor in the exhaust gasses into water. If you are looking for the good quality of furnace heaters, then it is the primary source to identify it.
What to check before purchasing any furnace heater or a boiler?
Finally, if you have any question regarding furnace heater, dont hesitate and let us know in a comment box. Even, you could add your phone number to get the prompt reply from our support team.
Hope that all the information will be liked by you about the product and if still have any query the please contact us.
Product Details:
Minimum Order Quantity: 6 PiecePower(Watts): As per requirement of applicationVoltage: As per requirement of applicationSize: As per requirement of application
BTH supplementary electric heaters are manufactured to conform the IPX4 rating and should be fitted only by the qualified electrician. BTH heaters are mostly used in the bathroom. According to I.E.E wiring regulations, the Electric heater must be earthed and connected to a cable outlet in the bathroom. This cable outlet should not be buried into walls and easy to accessible because it needs maintenance from time to time. It can be used for an industrial purpose such as oil and gas industry.
Note: BTH Heaters shouldnt be installed into the hot water domestic supply.
Instruction to read before using BTH heaters:
Types of BTH Heater:
BTH Heater is available in BTH 300, BTH 400 and BTH 500 edition according to the National Standard for Gas-Fired Water Heaters. The requirement of BTH heater depends upon equivalent length, the number of appliances connected and the supply of gas line size and concentric termination. There is different-2 requirement of BTH for the vent or gas pressure with the type of gas either natural or propane gas.
Features of BTH Heater:
BTH Heaters are used where the outlet process temperature doesnt exceed 87C.
Application of BTH Heater:
BTH heater is available into many models. Just check out the model which could full fill your requirement and then order it!
Finally, if you have any question regarding BTH Heater, Thermocouples or any other related stuff, dont hesitate. Just let us know your problem, question or suggestion and we will get back to you in no time.
APPLICATION :-
Product Details:
Minimum Order Quantity: 6 Piece
Power(Watts): As per requirement of application
Voltage: As per requirement of application
Size: As per requirement of application
Finned heatersorfinned tubular heatersare the electricalfinned heating elementsused in a variety of heat applications. While constructing and designing the tubular heaters, one needs to use the finest material such asstainless steel, Incoloy, Inconel, titanium alloys or steel. This material is decided based on the application of the material such as steel for alkaline cleaning solutions, incoloy for degreasing & cleaning solution, stainless steel for food processing equipment etc. These heaters can be of any size and shape based on your requirement. High-quality MgO (Magnesium Oxide) is also used for efficient heat transfer from resistive coil to your medium either it is air, liquid or solid.
Specification of Finned Heaters:
Application of Air finned Tubular Heater:
Features of Tubular heater:
Tubular air heaters are used for the heating of air (stoves), for ventilation and air conditioning devices, pipelines and annealing. Before purchasing tubular air heater, specify your use with the following details:
Now a days many examples can be seen in the market for household works likeelectric heaterwhich are easy to carry as well as they aresmall heater, as well asoven heatersor we can sayelectric oven heating element. All these type of gadgets are used in heating and known asheating element.
The requirement of Tubular Heater:
Once you finalized the following things, you could ask for a quote and if it meets your need Order It!
If you want to ask something, or you have any query then please contact us to know about the product.
Product Details:
Minimum Order Quantity: 6 Piece
Power(Watts): As per requirement of application
Voltage: As per requirement of application
Size: As per requirement of application
E Type Thermocouple
Thermocouples work as a temperature sensors for control and measurement. They are also used for converting a temperature gradient into electricity. There are two legs made of two different metals wires. These two legs/wires are bonded through welding, and at one end. This joint may be termed as a junction. This junction is the point where temperature finally gets read. Once you have measured something and there is a slight change, you will yourself feel change of voltage.
Different characteristics are possessed by different types of Thermocouples. Here we will discuss the features and limitations ofE Type Thermocouple.Everyone knows that if you are making any thermocouple product thenheating elementis very necessary, as I recommend to useelectric heatersin such cases if want proper heat on the same time.
E Type Thermocouple :
E Type Thermocouplehas potent to catch the signals with better and higher accuracy.
Range of E Type Thermocouple :
Extension wire 32F to 392F which is equal to 0C to 200C
Thermocouple grade wire -454F to 1600F which is equal to -270C to 870C
Accuracy (which will be greater) :
Special limits of error +/-1.0C or 0.4%
Standard +/- 1.7C or +/- 0.5 %
Limitations :
The sensitivity of thermocouple is comparatively small as compared to other types. This is so based on the reading of tens of microvolsts which are measured in Celsius. For better and clearer reading, you would need an offset amplifier, to read usable readings. You will surely need circuits or tables to measure things in better and efficient way. They have lower thermal mass. It may not read temperatures beyond 2300C.
The wires are well insulated and work efficiently. They are not insulated at the junction. If additional contacts are made or other objects are brought in between, it may affect the reading it finally gives.
Benefits and Uses:
Though there are multiple limitations with E-type thermocouple, yet they are worth use. The most commonly used sources, where such thermocouples are installed are:-
If want to give the order in bulk, so direct contact to thethermocouple manufacturers.
Conclusion :
While thinking of investing on thermocouples, for commercial uses, be easy as they are inexpensive and are interchangeable. They come with standard connectors. They are capacitated to measure wide temperature ranges. They are indeed very different than the other devices, used for measuring temperatures. They need not have an external or additional stimulant. Yes, temperatures may not be read accurately and readings are indeed compromised. But this limitation is based on the difference of one degree Celsius only.
In spite of too much of criticism, thermocouple and its variants are still used. Apart from this, If you have any query regarding product, dont feel shy to contact us in such cases.
Product Details:
Minimum Order Quantity: 6 Piece
Power(Watts): As per requirement of application
Voltage: As per requirement of application
Size: As per requirement of application
Features: