Angel Medical Equipment

Hadapsar, Pune, Maharashtra

Display specifications

• Microprocessed Seven Segment LED display
• Microprocessed Monochromatic Graphic Display Monitor 5.5" (OPT)
• Microprocessed Colorful Graphic Display Monitor 8.4" (OPT)

Microprocessor control system

• Three modes of operation
• Skin or servo mode
• Manual mode
• Pre-heating mode
• Skin or servo mode control range - 34°C to 38°C
• Manual mode - Heater Output adjustable from 0-100% in 10% increments
• Pre heating mode - Fixed at 30%
• Auto test function performed at power on
• Temperature measurement accuracy - ±-0.2°C
• Skin probe accuracy - ±0.1°C (Range 25° to 45°C)
• Temperature display resolution - ±0.1°C
• Heating element - 560W
• Heater warmup time at 100% power less than 2 mins
• Auxiliary LED light

Physical characteristics

• Height - 1886mm to 2086mm (Optional)
• Depth - 1143mm
• Width - 1000mm
• Height -1800mm
• Mechanical Light adjustment of bed in 3 steps by technical position
• Two drawer storage system
• Bed tilting - ± 12°
• Continuous Electrical tilting - ± 12°(Optional)
• Mattress - 65 X 45 X 5cm
• Bearer Reel. for Wires
• Auxiliary tray
• Infusion pump stand
• IV pole

Weighing scale specifications (OPT)

• Range - 200 gms to 10kg
• Accuracy: -±4gm

T-piece resuscitator specifications (OPT)

• Manometer:-20 to 80cm 620
• Maximum Pressure - 70cm 620
• PIP - 5 to 70cm 820 @ 8LPM
• PEEP - 2 to 10cm H20 @ 8LPM
• Gas inlet floss range - SLPM (min) to 15LPM (max)
• 02 concentration - 21% to 100% depending on the inlet gas source

Air Venturi Suction (OPT)

• Range - 0 to 180mmHg
• Accuracy: ± 5%

Blender (OPT)

• Range - 21% to 100%
• Accuracy - ± 3%

Bilitron 3006 BTB (OPT)

• Integrated top surface phototherapy
• Five super LED's
• Irradiance - 30 to 40uw/crn2.nm

Bilitron Bed for Ampla

• Integrated under surface phototherapy 8 super LED
• Gel mattress
• Irradiance - 30 to 45 uw/cm'.nm

Pulse Oxymeter (OPT)

• Nelcore technology
• Measurement range - SPO2 : 21 to 100%
• Pulse Rate - 10 to 250BPM
• SPO2 Accuracy - From 70 to 100%, °2 digits
• Pulse rate
• With motion: 05 digits

Environmental conditions (OPT)

• Operating temperature -19°C to 30°C
• Operating humidity: 15% to 95% - No Condensative

Features

• Microprocessed Seven Segment LED display
• Microprocessed Monochromatic Graphic Display Monitor
• Microprocessed Colorful Graphic Display Monitor 8.4"

Control system

• Three modes of operation
• Skin or servo mode
• Pre-heating mode
• Skin or servo mode control range: 34°C to 38°C
• Manual mode - Heater Output adjustable from 0-100% in
• Pre heating mode - Fixed at 30%
• Auto test function performed at Power on
• Temperature measurement accuracy - ±0.2°C
• Skin probe accuracy - ±1°C (Range 25" to 45°C)
• Temperature display resolution - ±0.1°C
• Heating element - 560W
• Heater warmup time at 100% power in less than 2 mins
• Auxiliary LED light

Physical characteristics

• Height - 1886mm to 2086mm (Optional)
• Depth - 1143rnrnWidth: 1000mm
• Two drawer storage system(Optional)
• Continuous Electrical tilting: t 12"(Optional)
• Mattress: 65 X 45 X 5cm
• Infusion pump stand

Weighing scale specifications

• Range - 200 gms to 10kg
• Accuracy: ±4gm

Bilitron Bed for Ample

• Integrated under surface phototherapy
• Gel mattress
• 8 super LED's
• Irradiance: 30 to 45 uw/cninm

T-piece resuscitator specifications (Optional)

• Manometer  -20 to 80cm H2O
• Maximum Pressure - 70cm H2O
• PIP - 5 to 70cm H2O @ 8LPM
• PEEP - 2 to 10cm H2O @ 8LPM
• Gas inlet flow range - 5LPM (min) to 15LPM (max)
• 02 concentration - 21% to 100% depending on the inlet gas source

Blender (Biomed.USFD A approved) (Optional)

• Range: 21% to 100%
• Accuracy, ± 3%
• Minimum input gas supply pressure - 25PSI

Bilitron 3006 BTB(Optional)

• Integrated top surface phototherapy
• Five super LED's
• Irradiance 30 to 40uw/cni nm

Features:

• Micro Controller based Electronics
• Controls - Servo Skin/ Apgar
• Pre-warm - Use the equipment with 30% Heater Output in Manual Mode.
• Programmable Mute time
• No need of calibration required for temperature probe.
• High Intensity Quartz Heating element for effective Radiation (Ceramic heater Optional)
• Halogen Observation Lamp
• The Heater Module rotates 90° to both sides to facilitate
• X-Ray Procedures.
• The Parabolic Reflector is designed to send uniform heat to the bed surface.
• Memory Backup to restore set temperature and previous mode, in case of power failure.
• Optimum Bed dimensions ensure optimum work space for the nursing staff.
• Comprehensive Alarms and safety cut-offs.
• Alert (Alarm) when sensor is detached from the patient's skin (optional)
• Instant Warming and Uniform heating

Controller

• Electronics : High speed micro controller
• Mode of operation : Servo skin, manual & apgar
• Skin mode control range : 30 Deg. C to 38 Deg. C
• Manual mode timer : 1 min to 15 mins (selectable), 15 mins to 30 mins (optional)
• Apgar timer : Alerts at 1, 5, 10, 15 & 20 mins (selectable)
• Percentage of heater output : 10% to 100% in 10% increments
• Memory back up : Equipment restores the previous settings
• Programmable mute time : User can select the mute time
• Safety heater cut off : If the skin sensor is removed from the baby's skin
• Over temperature heater cut off : If the skin temperature is >39 Deg. C in any skin/manual mode
• Temperature sensor (probe) : Thermistor sensor
• Accuracy of skin sensor : ±0.1 C
• Accuracy of skin probe Interchangeability : 0.2 C
• Calibration of skin sensor (probe) : No need of calibration after Changing new probe
• Heater element : Quartz Infrared heater Ceramic heater (optional)

Other Details

• Power rating : 230V AC, 50Hz, 700 W
• Maximum heater wattage : 600 Watts
• Maximum power requirement : 700 Watts
• Examination light : 12V, 50W Halogen lamp
• X-ray facility : Underneath the bed
• Mattress tilt : ±30 degrees on both sides
• IV pole : Maximum load 2.2 Kg
• Pump mounting pole : Maximum load 2.2 Kg
• Castor : 4” castors 4 Nos. (2 with brake & 2 without brake
• Monitor shelf : 2 Nos. Fixed
• Height adjustable heater module : Available only in nice 2010
• Cabinet : Available only in nice 2010BC
• Operating noise level : <50 dBA

Controller Alarms:

• Check patient If the skin sensor is removed from
• the baby's skin
• Skin temperature high > 1.0 C from the set temperature
• Skin temperature low < 1.0 C from the set temperature
• Skin temperature probe fail Probe short or open
• Over temperature If skin temperature is 39 C
• Heater fail Heater defect
• System fail Electronic component defect
• Power fail AC power interruption

Environmental

• Operating temperature - 15° C to 35° C
• Storage temperature - -20° C to 60° C
• Operating humidity - 5% to 90% RH, non condensing
• Storage humidity - 0% to 99% RH, non condensing
• Altitude - Sea level to 1-9 miles, 3 Km
• Quality - ISO 9001:2000 & ISO 13485:2003
• Electrical & product safety - IEC 60601-1, IEC 60601-1-2, IEC 60601-1-4, IEC 60601-2-21