Foot operated Impact Press model AMI-10 equipped with handchrome pillar, T slotted base for work holding. The precise control of striking load, the adjustable arm and wide throat permit using the press in various industries having maximum adjustable pressure upto 1000Kgs. working surface of table 150 x 100 mm, throat centre distance 130 mm

are manufactured from suitable case hardening steel, carburised, hardened and tempered and ground to close tolerance as per international standards. Collets are made out of suitable spring steel property heat treated and finished to desired accuracy. They are available in MT and ISO series. Collets are availableⁱⁿmetric 3 to 25 mm rising by 1 mm andinenglish 1/8" to 1" rising by 1/16".

Automatic wire straightening and cutting machine having an exclusive and elite combination of speed and accuracy backed by intensive research of experts. These machines are used where wire is further processed in rods, coiled wire accurate straightening, close length tolerances and high output are of importance, widely used by electric welding rods manufactures, electric fan guards, refrigerator racks, cloth hangers, automobile parts, electric parts industry, gives you both financial and inner core satisfaction as it is very easy to use requires no special skill.

Indefinite length of wire can be cut out without automatic attachment. The machine operates by drawing the wire from the coil through the fast rotating spinner, passes through a cutting of tool into the scaling bar where it strikes at the adjusted length and this stroke makes the cutting mechanism complete. This straightening function is performed by 5 straightening blocks which are adjustable and contains a simple to use straightening bush lets the user to make replacement to his own work

OPTIONAL:

• DoubleTool Post
• Auto Lifting
• Grinding attachment
• Side Tool Post
• Milling attachment
• Auto Lubrication

STANDARD EQUIPMENTS :Electric Motors Complete with Panel Board & Pendant Control for all operations. One Steel Telescopic Cover, One Boring Bar, Working Spindle Support Guide for Vibration Control, Co-ordinate reading arrangement with Scales & Verniers for X. Y.Z.-Axis and Handles. Facing head, 2No. Lubricating Pumps, 5 No. limit Switches & Automatic Rapid Travel, fitted with the Machine. Revolving Centre with 6"True Chuck Three Nos. Dial Indicators duly fitted in dust proof housings with attachment & Electric Coolant Pump.

EXTRA EQUIPMENTS :

• Milling Attachment.
• Taper Boring Attachment.
• Threading Attachment.
• 2Axis D.R.O.

SPECIAL FEATURES :

• 6 to 17.46 mm valve stem capacity.
• 0 to 90 valve angle adjustment.
• 27 to 79 mm valve head capacity (wet).
• 700 ml coolant water pot with baffle plates and filter.
• 4-point bearing mounting on both work and wheel tables for achieving better stability and precision.
• Bearing adjustment on feed screws with automatic end play take-up.
• Multi-start feed screw for rapid feeding of the workpiece.
• Quick damping collets.
• Diamond wheel dresser (which comes as standard) for grinding wheel dressing.

POLISHING DRUM
is made from steel fabricated angles & thick sheets. It required 2 HP. electric motor. It revoles at 40 to 45 R.P.M. & having a 200 Kg. capacity.

HAND - OPERATED BENDERS :
Benders are available in five rugged hand operated models. Bending capacity covers a material range from 1/16" wire to 1.1/4" inch round steel bar or its equivalent. Benders from a wide range of stock shapes including round, square, hexagonal, flat, and channel (all bar stock) and tubing. They come equipped with bend locating gauge for part duplication, Angle stop to determine degree of bend and locking pin to securely damp material. Radius forming possibilities from 0 to 12 inches. Torrington rollers installed in main bearing reduce friction, facilitate easy bending, and help bend large stock easily. Ratchet power assist for large stock is standard on Hand Model No. 4 and No. 5.

STANDARD EQUIPMENT :

• Bend locating gauge- setting this gauge allows any number of parts to be duplicated.
• Angle stop - locating this determines degree of bend.
• Locking pin - adjusting this securely damps material.
• Centre pin - provides one radius setup plus mount for other tooling.

EXTRA ACCESSORIES :

• ExtentionHandle (Model 2 & 3 only)
• Quick - Lock clamp
• Rugged welded work stand
• Die sets (Various sizes)

This Machine is used for faster operation of Line Boring of the Main Bearings and Cam Shaft Bearings of Automobile & Tractor Engines. The bar supplied with the machine is made from special alloy steel and grounded to accurate size. The machine is supplied with all equipments required for full Operation.

Standard Accessories :

• Sanding Belt
• Sanding Disc
• Motor Pulley
• Tool Kit.

• Ram & Table designed with inclined member and box type structure for maximum strength.
• Positive holding of Hyd. Hold downs avoids slippage of sheet during cutting stroke.
• HCHCr Blade suitable to MS & SS.
• Hardened Transfer bars.
• Front gauging by disappearing stoppers mounted on front squaring arm.

Note :
Any cavity or solid block can be manufactured. Concrete platform to be used for Casting of blocks -approx-. 2500 sft. for 8 hrs. Shift working.

Automats are extremely versatile machines that give big returns on small investments. Upto 80% of all turning jobs can be profitable handled by these automats with accuracy and precision. These Automats have proved economical for mass production of simple and complex turned parts for Automobiles, Bicycles, Tractors, Diesel Engines, Pumps, Radios and electronics, Sewing Machines, Aircraft and so on. The simple design of these Automats greatly reduces the time for change-over of tooling set-up from one components to another.

STANDARD EQUIPMENTS :
Front & Rear Main Slides, Tailstock Barstop, One Collet With Drill Holder, Electric Drive Motor, Electric Coolant Pump, One Set of Cam Blanks, One Silent Gravity Bar Feed Chest, Trans-parent Splash Guard, Change Gears.

ADDITIONAL ACCESSORIES : (AT EXTRA COST) :
Single Vertical Slide, Double Vertical Slide, Long Turning Attachment (Front & Rear), Various Types of Tool Holders, Finished Cams, Collets Chamfering Attachment, Tooling and Setting.

STANDARD EQUIPMENTS :

• Micrometer with frames (Indian Make)
• Tool Bits Nos. 2
• Pin Set 5 No. Small and Big Size
• Allen Key Set one Pc.
• One Spanner

Capacity - 10/7 CFT (300/200 Ltr) 5m³/hr. (1 Bag capacity mixer) without loading Hopper and wheels C.I. Mixing drum and yoke assembly, strong steel chassis.Mixer is powered by 3 HP, 3 Phase motor. or 5 HP Diesel Engine.

Drive :Belt Drive

Standard Accessories :
Suitable Electric Motor 3 Phase with Switch & Wiring, Motor Pulley, V-Belt, Drill Chuck & Arbour.

Extra Accessories :
Drilling Vice, Machine Lamp, Motorised Coolant System with Assembly, Tapping Attachment.

Hand operated Jenny or Burrying machines are designed for edging flanging or burying the edges of all classes of tin plate work of any shape, generally used for edging and flanging bottom and bodies to various angels previous to panning or setting down, double seaming etc. provided with an adjustable guage, a set of rolls and mounting bench.

These machines are useful for curling and wiring of cylindrical bodies and plane sheets, for flanging bodies, blanks and bottoms and for seaming of elbows, bottoms and the like. Cutting operations can be performed, if the machine is provided with cutters. Due to its manifold application this machine has become indispensable for plumbing shops.

Working examples

Using the flanging rolls B supplied with the machine there can be provided rounded with flanges without folds only up to 3 mm height providing curls at bodies for wiring is performed as illustrated beneath.
For closing the curl for wiring closing rolls Z are used, refer to illustrations 5 and 6, after a corresponding ring of wire has been inserted in the curl and attached at several points.
For wiring plane sheets or strips the mode of operation is similar to that illustrated by Fig. 3 to 6. If it should be necessary to close the curl perfectly around the wire special closing rolls S are required, the normal closing rolls Z not being suitable for this propose.

Pipe Threading Machines are designed to give maximum efficiency and reliable performance under the most severe conditions of service with minimum maintenance cost. All the necessary requirements are combined in this model to form the basic fundamentals of correct threadings. All the gears are made of case hardened steel with extra large face width and tooth thickness and cut onhobbingmachine for noiseless operation even at high speeds. Naturally they are built with high standards of workmanship, material and quality.

Headstock :
The Headstock is of top quality casting proving support to the spindle bearings. The spindle swing or taper roller bearings are of best steel with a grounded finish to give accurate results. Gears of Head Stock are running in Oil Bath with Oil level window.

The Bed :
The Bed is pillar type having two pillars made of best steel, nicely grounded and also aligned accurately to the headstock alignment.

The Saddle:
The Saddle is fitted on two pillars very precisely. It runs on pillars very smoothly and accurately to the head stockalignmernt.

The Apron :
The Apron gives movement to the Saddle with head transfer along with pillars through steel rack and pi8nion arrangements. Its all gears are made of best steel.
Vice Jaws :
The Vice Jaws are fitted on the saddle with V-ways accurately. The jaws are made of best steel and are well hardened. The movements of jaws are controlled by a screw on the saddle.

Lead Screw :
The lead screw attachment is an extra device which has been arranged to supportthethreadcuttingchassersin big threading machines, only having eleven TPI range.

SAW FRAME :This of regid construction & runs in prismatic guide ensuring a parallel cut. This cut takes place on the draw stroke & the hydraulically liften out of contact with the workpiece on the forward stroke to prevent wear or the blade & can out metals of all kinds & strength.

FEED:Two levers are provided at the pot one regulators the rate of feed while the other enabled the bow slide to be raised or forwarded hydraulically bow raised automatically & motor Switched off on completion of the cut.

BED:The bed is of large proportion provided with guide ways for the vice for clamping the material vice is of rigid constructional. One jaw remains fixed & the other can be adjusted according the material to be cut.

ELECTRICAL EQUIPMENT :A direct on line push bottom starter can be fitted which incorporates & adjustable trip mechanism which stops the machine as soon as the blade is clear from the work non productive time is reduced to minimum.

DRIVE :Power is supplied by a suitable electric motor through Vee-Belts which are full adjustable for tension all drive mechanism being totally enclosed.

SPEED :The incorporation of two-speed driving mechanism allows for the most suitable speed to selected for material being cut.

COOLANT :The Coolant tank is totally enclosed in the machine base & a Speed Pump supplies coolant to the saw blade through a stay put pipe & top.

Mechanical roller bearings fittedmotorisedrapid bending machinedesingedto provide a simple, trouble free multitudeofbendingsjobs which might arise in an industry, simple compound and reverse bends can all be formed with the power bender in tubing, angle, channel, extrusions, mouldings, stripstock, bus bars, round or squarerods and all other solid ductile materials. The material is locked between the radius collar and locking pin and, as the mounting plate rotates the material is drawn past the forming nose or a forming roller which can of used for many operation. This arrangement is ideal for a wide suitable; of forming requirements in most solid materials and is especially variable for bending eye bolts as it will form both centered and off center eyes in one operating cycle. The radius capacity of this unit isunusallylarge and any radius desired can be obtained by merely placing acoller

of the required size in the mounting plate. Since the mounting plate allowsbendingsfull 360, it is necessary to use this set-up when forming tubing.angle, channelmouldingsand extrusions in excess of the 280 angle range of the toggle clamp set up. This can be easily accomplished through the use of the proper accessories, eqippedwith 5.H.P.A.C. 440/3/50 electric motor, reduction gear unit, starter, bend locking gauge, angle stop.Locking, pin; radius and forming collar and radius block having bending speed approx 8 R.P.M Capacity standard iron pipe M.S.10swg. I.P.S.1.1/2" centered eye-round mild steel bar (one operation 3/4" centered eyerapindmild steel (two operations) 1", square mild steel bar 3/ 4", flat steel bar bent flat 3/8" x 4", angle 3/16" x 1" x 1", channel 3/16" x 2" x 1" (Prices for various accessories attachment can be quoted against specific enquiry/drawingor sample)

Model AMI 28 : Heavy duty box section, M.S. Body, Double leverage type for quick cutting of light rods, lever retaining spring to hold handle failing off accidently. Model AMI / 16, 20 and 24 are single leverage type.

One head as per the Power flanging machine and the otherhead is fitted with punches to produce the louvers in the rightangle flange to suit button punch snap lock. 1.00 mm maximum.

When used in conjunction with the double headed flanging machine, this makes possible the forming of round bends.

Foot operated Impact Press model AMI-10 equipped with handchrome pillar, T slotted base for work holding. The precise control of striking load, the adjustable arm and wide throat permit using the press in various industries having maximum adjustable pressure upto 1000Kgs. working surface of table 150 x 100 mm, throat centre distance 130 mm

are manufactured from suitable case hardening steel, carburised, hardened and tempered and ground to close tolerance as per international standards. Collets are made out of suitable spring steel property heat treated and finished to desired accuracy. They are available in MT and ISO series. Collets are availableⁱⁿmetric 3 to 25 mm rising by 1 mm andinenglish 1/8" to 1" rising by 1/16".

Automatic wire straightening and cutting machine having an exclusive and elite combination of speed and accuracy backed by intensive research of experts. These machines are used where wire is further processed in rods, coiled wire accurate straightening, close length tolerances and high output are of importance, widely used by electric welding rods manufactures, electric fan guards, refrigerator racks, cloth hangers, automobile parts, electric parts industry, gives you both financial and inner core satisfaction as it is very easy to use requires no special skill.

Indefinite length of wire can be cut out without automatic attachment. The machine operates by drawing the wire from the coil through the fast rotating spinner, passes through a cutting of tool into the scaling bar where it strikes at the adjusted length and this stroke makes the cutting mechanism complete. This straightening function is performed by 5 straightening blocks which are adjustable and contains a simple to use straightening bush lets the user to make replacement to his own work

OPTIONAL:

• DoubleTool Post
• Auto Lifting
• Grinding attachment
• Side Tool Post
• Milling attachment
• Auto Lubrication