Amiable Impex

Borivali West, Mumbai, Maharashtra

For most connections involving lugs, cable or rectangular bus, exothermic handle clampsare used.
These will fit 90% of all standardexothermic molds.Normally we recommend One Handle for every two moulds
These are manufactured by the professionals using high quality raw material. TheseMold Handle Clampconform theiradherence with the industry standards.
Features:
-Light in weight (Nearly 1.5 to 2.0 Kg)
- Handy in nature-Rust-proof-Tare used for two part molds

It is used to remove the metal Scrap from Mould after the Welding Process is done.

We recommend One Slag Tool for Every 200 Joints

When making a copper wire connection of Ground rod or other metal connection, place theWelding powderinto thegraphite mould.Just ignite to start the Weldinging process. The result will be clean and smooth connection surface. It is also applicable for other metal such as: Iron, GalvanizedSteel, Railway track, Cast Iron, Bronze, and Brass. It can be used in various applications to have the certainly good connections in work. Such as Lightning and Surge Protection, Grounding in Electrical Work, Railway Construction, Cathodic Protection.

The connection mould is designed tolast for an average of 60 to 100 connections.This will vary according to the care given the mould duringuse.Graphite mould is made of high quality graphite suitable for high quality Weldinging work and can be used for several times.

Features:
-Dimensional accuracy as per the customers demand.
- High quality Graphite which ensures Longer Life.

Exothermic Welding Powderis the most reliable and consistently-performing Welding metal availablewith us.Quality validationsteps are taken for every lot we produce. Upon final acceptance, our Welding metal isspecially packaged in moisture-resistantplastic cartridges with special closure caps. Then the cartridgesand required metal discs are packaged in moisture-resistant boxes.
Our standard packingfor Weldinging powder is the following -Firstly Weldinging powder is in the tube and starting powder / IgnitePowder is in tube at the bottom of
Welding powderas shown in diagram

Moisture Free Packing in Foil

All sizes of Welding metal are available.
Standards Size Packing available are 15 Grams, 25 Grams, 45 Grams, 65 Grams, 90 Grams, 115 Grams, 150 Grams, 200 Grams, 250 Grams

Features:
-High quality products atAffordable prices-High performance

Gloves is required for safety purpose as theExothermic Welding Powdermelts at more than 1400 degree Celcius.

We recommend a Pair of Gloves for Every 150 Joints
Features:
-High quality Gloves that can easily bear heat upto 400 degree Celcius which is more than enough to Hold the Mould.

It is designed with the advantages of safety and convenience. It is used to igniteStartingPowderin order to result inexothermic reaction.
We recommend one Flint Gun for every 100 Shots

Steel discs are very important. The disc acts timing device to allow the Weldinging powder to heat
to proper temperature.Steel Disk is designed to contain the exothermic reaction to the upper crucible of a molduntil the reaction is complete and ready to Welding.One Metal is must for every shot
Features:
- Depressed center
- Medium hard bond
- High speed rotation

Graphite absorbs moisture from weather. So there is a need for propane torch to dry out the inside of the mouldthoroughly on both sides, therefore heating the mold to approximately 250 degrees Fahrenheit
We recommend using one Flame torch for Every 200 Joint and than use the refiling

Product Features For Exothermic Welding:

• Safe operation, without professional technology knowledge or any other special protection, easy to learn.
• Without external energy, very simple tools and equipment, execution of high efficiency.
• Connector in copper of high purity, strong corrosion resistance.
• The connector to be formed in metal bonds, not loose.
• Current carrying capacity of the connector is greater than that of wire connector.
• Widely applied , can be used for copper to copper, copper to steel, welding between copper and galvanized steel and other metal materials.
• Connectors can withstand multiple large inrush current impact without degradation.

Ignite Powderis also known asStarting Powderand is required and is must. Sprinkle littleStarting Powderon theMouldfollowed
by theExothermic Welding powderand again sprinkle it little on the Top Side of Mould. Than Ignite starting powder with a spark gun.
This results in exothermic reaction and theWelding powder melts to molten copper alloy. The molten copper alloy melts the
retaining disc and flowsinto the Welding cavity where it partially melts the conductors.
Ignite Powder of 2-4 grams is sufficient
for this Process.
Features:
-High quality Ignite Powder withFast Ignition ability.