FRP Cooling Towers are manufactured with Glass reinforced plastic mostly in wind with standing bottle type and square type models. It is a mechanical type Counter Flow Tower. FRP Cooling tower intakes the air from bottom and discharge the waste heat at the top. Since the water is traveling from top and the air passes from bottom to top, the water droplet have more direct contact time with air. The wet cooling Towers are cooled with the help of evaporating some proportionate quantity of cirulating water.

The bottle type tower casing is filled with Honeycomb type PVC FILLS. The rotating water distributor sprinkler is fixed in the top of the inlet pipeline and the same distributes the hot water evenly over the Honeycomb Fill media. The sprinkler will be operated with self-propulsion system. The PVC Fills is corrugated with channels between each flutes to prevent the blockage and giving more and large surface area per unit volume. The cold air meets the cold water at the bottom of the infill providing maximum evaporation and heat transfer in the infill.

Finally FRP Cooling Towers are more compact, light in weight, least power consumption, long-lasting, Durable and lowest maintenance expenditure. Since Epoxy Coated / Hot dip galvanized structural and zinc plated fasteners (stainless steel fasteners on extra cost) are used, FRP Towers are corrosion Free.

Adjustable pitch, Aluminium [LM-6] or FRP Fan Blades are directly mounted on the Electric motor [IP 55, with Stainless steel shaft, TEFC Special type cooling tower motor] to avoid excess power consumption and unnecessary gear driven problems. All moving parts can be easily approached from top. So easy maintenance is possible. Smaller capacities are factory assembled and just bolting at site is enough. However higher capacities are assembled into the site only to avoid excess transportation cost. Our range includes 10 TR to 500 TR in single cell and multiple cells are used for further capacities.

The FRP/ Timber Natural traditional Cooling Towers are called as Fan less or Fill less Cooling Towers, because in this model no fan or fill is used to cool the water.

In Timber atmospheric / Fan less Cooling tower , Treated wooden louvers were used as the side wall of the Cooling Tower to restrict the water spillage and allow the outside wind passage to go inside the Cooling Tower and act as the Cooling media. Simply says, in Fan less Cooling Towers the Hot water will be sprayed in the top of the Cooling Tower with spray nozzles into small droplets like mists and the droplets are crossed with the atmospheric wind flow to get the water cooled. The same technique is used in FRP Fan less / Natural Draft / Fill less Cooling Towers. Instead of costly timber louvers, FRP louvers are used. This Fan less cooling towers are very economically operating Cooling Tower. Since there is no fan or electric motor, there is no huge operating or maintenance cost involved in this Cooling Tower. And also in Energy efficiency point of view, this is the best Payback Cooling Tower when comparing with other models.

And also very low noise operated Cooling Tower. The noises of other model cooling towers are due to Fan, Motor, Gear box and Drive shaft and its vibrations only. Since these models of Cooling Towers are not having Fan, motor, Gear boxes, this equipment has no trouble-some of noise and vibration.

This model Cooling Towers are water saving and pollution free, safety with environmental protection

We are offering all types of cooling tower like frp cooling tower, wooden cooling tower, rcc cooling tower.

FRP Cooling Towers are manufactured with Glass reinforced plastic mostly in wind with standing bottle type and square type models. It is a mechanical type Counter Flow Tower. FRP Cooling tower intakes the air from bottom and discharge the waste heat at the top. Since the water is traveling from top and the air passes from bottom to top, the water droplet have more direct contact time with air. The wet cooling Towers are cooled with the help of evaporating some proportionate quantity of cirulating water.

The bottle type tower casing is filled with Honeycomb type PVC FILLS. The rotating water distributor sprinkler is fixed in the top of the inlet pipeline and the same distributes the hot water evenly over the Honeycomb Fill media. The sprinkler will be operated with self-propulsion system. The PVC Fills is corrugated with channels between each flutes to prevent the blockage and giving more and large surface area per unit volume. The cold air meets the cold water at the bottom of the infill providing maximum evaporation and heat transfer in the infill.

Finally FRP Cooling Towers are more compact, light in weight, least power consumption, long-lasting, Durable and lowest maintenance expenditure. Since Epoxy Coated / Hot dip galvanized structural and zinc plated fasteners (stainless steel fasteners on extra cost) are used, FRP Towers are corrosion Free.

Adjustable pitch, Aluminium [LM-6] or FRP Fan Blades are directly mounted on the Electric motor [IP 55, with Stainless steel shaft, TEFC Special type cooling tower motor] to avoid excess power consumption and unnecessary gear driven problems. All moving parts can be easily approached from top. So easy maintenance is possible. Smaller capacities are factory assembled and just bolting at site is enough. However higher capacities are assembled into the site only to avoid excess transportation cost. Our range includes 10 TR to 500 TR in single cell and multiple cells are used for further capacities.

The FRP/ Timber Natural traditional Cooling Towers are called as Fan less or Fill less Cooling Towers, because in this model no fan or fill is used to cool the water.

In Timber atmospheric / Fan less Cooling tower , Treated wooden louvers were used as the side wall of the Cooling Tower to restrict the water spillage and allow the outside wind passage to go inside the Cooling Tower and act as the Cooling media. Simply says, in Fan less Cooling Towers the Hot water will be sprayed in the top of the Cooling Tower with spray nozzles into small droplets like mists and the droplets are crossed with the atmospheric wind flow to get the water cooled. The same technique is used in FRP Fan less / Natural Draft / Fill less Cooling Towers. Instead of costly timber louvers, FRP louvers are used. This Fan less cooling towers are very economically operating Cooling Tower. Since there is no fan or electric motor, there is no huge operating or maintenance cost involved in this Cooling Tower. And also in Energy efficiency point of view, this is the best Payback Cooling Tower when comparing with other models.

And also very low noise operated Cooling Tower. The noises of other model cooling towers are due to Fan, Motor, Gear box and Drive shaft and its vibrations only. Since these models of Cooling Towers are not having Fan, motor, Gear boxes, this equipment has no trouble-some of noise and vibration.

This model Cooling Towers are water saving and pollution free, safety with environmental protection

We are offering all types of cooling tower like frp cooling tower, wooden cooling tower, rcc cooling tower.