The compaction factor is defined as the ratio of the mass of the concrete compacted in the compaction factor apparatus to the mass of the fully compacted concrete. It involves dropping a volume of concrete from one hopper to another and measuring the volume of concrete in the finmore...
The strength of concrete is generally estimated after 28 days by crushing field test cubes or cylinders made from the representative concrete used for the structure. The utility of ascertaining strength after 28 days is often questioned since by this time considerable concrete womore...
Concrete permeability tester for three specimen : (100mm dia x 100mm height) or (150mm dia x 150mm height) or (150mm cube) is also available.
Permeability Cell : Consists of a metal cylinder with a ledge at the bottom for retaining the specimen, a flange at the top, removable cover plate and a funnel. A rubber gasket is seated in matching grooves, between the cell and the cover plate, to render the joint water tig
Supply Type : Manufacturer
Water Reservoir : Consists of a length of metal pipe, 50 to 100 mm in diameter and about 500 mm long. The reservoir fitted with a graduated side arm gauge-glass for admitting water and compressed air and a cock for drainage, bleeding and connection to the permeability cell
specimen size : Â 100 X 100 mm
Specifications : The set up consist of permeability cell, water reservoir and pressure lines, with glass bottles.
we are regarded as notable manufacturer, exporter and supplier of slump cone apparatus in the market. Our slump cone apparatus provide highly accurate results that can match up with premium quality standards of the industry. We offer slump cone apparatus at affordable rates. more...
Used for the measurement of resistance to plastic flow of cylindrical specimens of bituminous paving mixtures when tested in a marshal load frame. Test specimens are produced and tested at a speed of 50.8mmmin.The maximum load(stability) and deformation(flow) of the specimen are more...
We hold expertise in offering marshall stability test apparatus that is used for widely used for designing and evaluating bituminous paving mixes. The marshall stability test apparatus offered by us, can be availed at market leading prices. the apparatus consist of the following more...
Capacity 200 kg. for cement concrete flooring tiles. The specifications are similar to the above machine, but for the bearing rollers of 25 mm dia and spans of 150, 200 and 250 mm. The load is applied at the rate of 200 kgminmeter. Without lead shots.more...
J-ring test the passing ability of the concrete .The equipment consists of rectangular section of 38 mm X 25 mm open steel ring drilled vertically with holes to accept threaded section of reinforcing bars 12 mm diameter 100 mm in length.The bars and sections can beplaced at diffemore...
This test is used to determine the elapsed time between batching of a concrete sample and when it is deemed by standard methods to have set. The method involves measuring the penetration resistance of a test sample, which has had coarse particles removed at periodic intervals. Itmore...
Description and specifications : The apparatus comprise of a slump cone with handles made of mild steel sheet, a chrome plated steel tamping rod of 16 mm diameter X 600 mm long, rounded off at one end, with a scale marked on it and a steel base plate with a carrying handle. Etc
Optional Accessories : : CONCRETE SCOOP. FUNNEL FOR POURING CONCRETE IN CONE STRAIGHT EDGE
Introduction he oldest, most widely used test for determining workability. This test is used to determine the workability of fresh concrete, which would normally be undertaken at the point of delivery to ensure the concrete, is of adequate consistency for placement. The test is amore...
The oldest, most widely used test for determining workability. This test is used to determine the workability of fresh concrete, which would normally be undertaken at the point of delivery to ensure the concrete, is of adequate consistency for placement. The test is applicable tomore...
Introduction The oldest, most widely used test for determining workability. This test is used to determine the workability of fresh concrete, which would normally be undertaken at the point of delivery to ensure the concrete, is of adequate consistency for placement. The test is more...
Introduction The compaction factor is defined as the ratio of the mass of the concrete compacted in the compaction factor apparatus to the mass of the fully compacted concrete. It involves dropping a volume of concrete from one hopper to another and measuring the volume of concremore...
  Introduction This test is used to determine the elapsed time between batching of a concrete sample and when it is deemed by standard methods to have set. The method involves measuring the penetration resistance of a test sample, which has had coarse particles removed at permore...
Backed by a team of highly skilled engineers, Kant Plastology engaged in providing a wide range of VICAT SOFTENING POINT APPARATUS. The compact and elegant look of apparatus contains high efficient S.S. 304 tubular heating system for appropriate rate of rise of heat and stirrer mmore...
VSP is used to determine the deflection temperature limit for specific application and comparing the heat softening characteristics of thermoplastic material at constant load in oil up to 300º C with specified rate of rise. Plastic materials being heat sensitive in nature has a more...
VSP is used to determine the deflection temperature limit for specific application and comparing the heat softening characteristics of thermoplastic material at constant load in oil up to 300º C with specified rate of rise.more...
the oldest, most widely used test for determining workability. This test is used to determine the workability of fresh concrete, which would normally be undertaken at the point of delivery to ensure the concrete, is of adequate consistency for placement. The test is applicable tomore...
A concrete structure is considered to be of adequate durability if it performs in accordance with its intended level of functionality and serviceability over an expected or predicted life cycle. Concrete durability depends largely on the ease (or difficulty) with which fluids (wamore...
This test is used to determine the elapsed time between batching of a concrete sample and when it is deemed by standard methods to have set. The method involves measuring the penetration resistance of a test sample, which has had coarse particles removed at periodic intervals. Itmore...
California Bearing Ratio Test Apparatus, Field Type (AIM 155) Â This apparatus, mounted on a rolled steel joist cantilevered from the back of the truck or fitted to the underside of a mobile frame, can be used to determine the bearing ratio (generally known as the California Beamore...
Consolidation Test Apparatus (AIM 125, 125-1, 126, 126-1, 127-1/2/3, 129, 129-1/2/3) Ref Stds : IS 2720 (Part15), IS 12287, BS 1377, ASTM D 2435 Â Consolidation of clay deposit leads to distress in buildings such as cracks and failures. Consolidation is reduction of volume of somore...
Vane Shear Apparatus, Motorised (AIM 108) Ref Std : IS 2720 (Part 30) Â Vane Shear Tests are conducted where it is difficult to obtain suitable specimens or where intrusion from a sampling tube may cause too much of a disturbance.Consists of a special motor, adjustable in heightmore...
Hand Driven Operated ASTM C 151 also specifies the use of shrinkage bar moulds for the determination of soundness. Length Comparator listed in the concrete section determines the change in length of the specimen. Two models are offered. One is provided with stainless steel smoothmore...
Soil compaction is a fundamental requirement for the construction of earth fill for dams, reservoirs, canal embankments, highways, railways and runways. The relationship between soil moisture content and compacted dry density is very useful for deciding construction specificationmore...
This is used for determination of in situ dry density of natural or compacted fine grained soil, free from aggregates. A cylindrical cutter is used to extract a sample of the soil with the help of a dolly and rammer. From the weight, density and the moisture, and dry density of tmore...
We believe in keeping transparency in the transactions and thus we offer an invoice to the clients stating all the necessary details. We undertake both online and offline payment processing methods. As one of the leading Suppliers, we keep our quality in synchronization with our more...
Introduction Hand operated With Automatic Timer Hand Operated : The apparatus consist of a cast aluminium base with an iron stand on which moves an aluminium arm. A 6" dial is fixed on this arm and a brass chromium plated rod slide through the lower portion of the arm. A needle wmore...
It consists of a frame with sliding panel with accurate slots of different standard width and length, the complete assembly is chrome plated or powder coated. more...
The apparatus, consist of a rigid frame that supports two conical hoppers vertically aligned above each other and mounted above a cylinder. The top hopper is slightly larger than the bottom hopper, while the cylinder is smaller in volume than both hoppers. To perform the test, thmore...
We are leading importer & supplier for the products which also includes baby cap booties & mitten sets, baby stretch caps & cap-bootie-mitten sets. more...
Our organization is involved in providing a qualitative Pile Integrity Tester to our customer. These test are performed by pulse echo or Transient Response Method used to test piles integral in the structure. Pile Integrity Tester is available in several configuration to meet themore...
The California bearing ratio test is penetration test meant for the evaluation of subgrade strength of roads and pavements. The results obtained by these tests are used with the empirical curves to determine the thickness of pavement and its component layers. This is the most widmore...