Write a Review
Our Products
We offer a complete product range of Smd Rework Station, Soldering Iron, Quick heat Soldering Iron, Solder Pot and Temp. Controlled Soldering Station PX-501AS
Reaches set temperature fast with the Quick Start circuit.
Accurate calibration.
| Model | PX-501 | PX-501AS | PX-601 | PX-601AS |
| Voltage | 110V, 220–240V AC 50/60Hz | |||
| Power Consumption | 85W | |||
| Power Cord Length | 1.5m | |||
| Temperature Setting Range | 250–450°C | |||
| Ripple temperature | ±5˚C (unloaded) | |||
| Insulation Resistance | Over 100MΩ (500V DC) | |||
| Accessories | Soldering Iron Tip (PX-60RT-B) | |||
| Control Unit | ||
| Output Voltage | 110V, 220–240V AC | |
| Dimensions | 100(W) × 57(H) × 85(D)mm | 48(W) × 31(H) × 130(D)mm |
| Weight | 266g | 75g |
REWORK UNIT
The temperature can be set to max 550C.
SOLDERING UNIT
Good for a wide range of soldering work with 70W heater.
DESOLDERING UNIT
Instant desoldering with open-valve mechanism.(Please refer to the next page.)
INDIVIDUAL POWER SWITCHES
Along with the main power switch, there are switches for soldering, desoldering, and reworking.
Desoldering and reworking operate simultaneously
With open-valve mechanism
A wide range for terminals, connectors and flat ICs (soldering & desoldering)
To keep the temperature constant during desoldering
Reduces noise during heater ON/OFF
Two-stage trigger switch (PAT.P)
Step 1
Pulling the trigger (lightly) activates the first stage switch. The pump starts, and the air pressure decreases in the vacuum chamber.
Step 2
Next, pulling the trigger fully activates the second stage. The open-valve will open, and the solder is sucked up at once by the negative pressure in the vacuum chamber.
| MODEL | SVS-800AS | |
| Voltage | 220-240V AC 50/60Hz | |
| Power Consumption | 670-760W | |
| Power Cord Length | 1.5m Inlet type | |
| Temp. Setting Range | Desoldering Unit | 250−450°C |
| Soldering Unit | 200−480°C | |
| Rework | 150-550℃ | |
| Insulation Resistance | Over 10MΩ(500V DC) | |
| Vacuum Pump System | Diaphragm system | |
| Vacuum | - 0.08MPa (-600mmHg) | |
| Air Flow | 5-25L /min | |
| Accessories | Cleaning pin TP-100CP-13 / Soldering iron stand ST-76 | |
| Total Weight | 9.3kg | |
Two-stage trigger switch (PAT.P)
Step 1
Pulling the trigger (lightly) activates the first stage switch. The pump starts, and the air pressure decreases in the vacuum chamber.
Step 2
Next, pulling the trigger fully activates the second stage. The open-valve will open, and the solder is sucked up at once by the negative pressure in the vacuum chamber.
With open-valve mechanism
A wide range for terminals, connectors and flat ICs
To keep the temperature constant during desoldering
Reduces noise during heater ON/OFF
Makes changing the filter easy
The open-valve allows the device to reach vacuum pressure of -0.06MP (approx.-450mmHg) in only 0.1second. (about 4 times faster than ourTP-200AS).
Two-stage trigger switch (PAT.P)
Step 1
Pulling the trigger (lightly) activates the first stage switch. The pump starts, and the air pressure decreases in the vacuum chamber.
Step 2
Next, pulling the trigger fully activates the second stage. The open-valve will open, and the solder is sucked up at once by the negative pressure in the vacuum chamber.
With open-valve mechanism
To keep the temperature constant during desoldering
Makes changing the filter easy
The open-valve allows the device to reach vacuum pressure of -0.06MP (approx.-450mmHg) in only 0.1second. (about 4 times faster than our SVS-500AS).
| MODEL | SVS-580AS | |
| Voltage | 110V,120-130V,220-240V AC 50/60Hz | |
| Power Consumption | 110V,120-130V (200W) | |
| 220-240V (270-300W) | ||
| Power Cord Length | 1.5m | |
| TemperatureSetting Range | Deoldering Unit | 250−450˚C |
| Soldering Unit | 200−480˚C | |
| Insulation Resistance | Over 100MΩ(500V DC) | |
| Vacuum Pump System | Diaphragm system | |
| Vacuum | - 0.08MPa (-600mmHg) | |
| Accessories | Cleaning pin TP-100CP-13 | |
| Soldering iron stand ST-76 | ||
| Total Weight | 4.0kg (w/o cord ) | |
| CONTROL BOX | ||
| Output Voltage | 110V,120-130V,220-240V AC | |
| Dimensions | 205(W) x 170(H) x 160(D) mm | |
| Weight | 3.6kg (w/o cord, hose ) | |
5 zone profiles available: PREHEAT 1, PREHEAT 2, PREHEAT 3, REFLOW, and COOL. Up to 19 profiles* can be saved for each of the 5 zones. One profile can be registered for HAND Mode.
Accurate P temperature control. Heater and Vacuum switches located on the handpiece for easy control.
ON/OFF interface with Preheater (connection cable optional). Keypad lock and Offset functions. lInstant cool down on all zones by pressing the COOL key.
*individual profiles with specific temperature and time settings can be pre-programmed for each of the 5 Zones
With PID control
Controls external preheater
Heater and vacuum switches on the handpiece
On all zones with cool key
Up to 19 profiles, each with 5 zones
| SPECIFICATION | |||||
| Model | XFC-301 | XFC-300 | XFC-210 | XFC-110 | XFC-100 |
| Voltage | 220–240V AC 50/60Hz | 220V, 230V, 240V AC 50/60Hz | 110–130V, 220–240V AC 50/60Hz | ||
| Power Consumption | 400–460W | 470W | 420–470W, 380–420W | ||
| Power Cord Length | 1.5m Inlet type | 1.1m (3 core cord) ground plug | |||
| Temperature Setting Range | 50–550°C | 150–550°C | 150–450°C | ||
| Insulation Resistance | Over 10MΩ (500V DC) | ||||
| Station Unit | |||||
| Model | XFC-301 | XFC-300 | XFC-210 | XFC-110 | XFC-100 |
| Output Voltage | 220–240V AC | 220V, 230V, 240V AC | 110–130V, 220–240V AC | ||
| Air flow Meter | Equipped | − | |||
| Air flow Volume | 5–25L /min | 5–23L /min | 5–25L /min | 5–20L /min | |
| Auto-lift function | Included | - | |||
| Modes | 3 (Profile-Normal, Profile-Auto, Hand) | 3 (Profile-Flat, Profile-Slope, Hand) | 1 (Hand) | ||
| Temperature Profiles | 5 Zones (Temperature and Time) | − | |||
| Profile Memory | ( Auto, Normal )×19, HAND×1 | ( Flat,Slope)×19, HAND×1 | − | ||
| Dimensions | 200(W) ×230(H) ×265(D)mm | 182(W) ×179(H)× 263(D)mm | 107(W) ×177(H)×227(D)mm | ||
| Weight | 7.6kg ( w/o cord ) | 8.4kg ( w/o cord ) | 7.8kg ( w/o cord ) | 4.6kg ( w/o cord ) | |
| Accessory | Connection Cable with Preheater, Handpiece Holder, XVCW-SET | Handpiece Holder,XVCW-SET | Handpiece Holder | ||
| Handpiece Unit | ||||||
| Model | XFC-301 | XFC-300 | XFC-210 | XFC-110 | XFC-100 | |
| Voltage | 220-240V AC | 220V, 230V, 240V AC | 110-130V AC | 220-240V AC | ||
| Power Consumption | 370-430W | 400W | 400-450W | 300-400W | ||
| Heater | Nichrome Heater | |||||
| Hose length between Handpiece and Control Unit | 1m | |||||
| Vacuum Pickup | Integrated into Handpiece | − | ||||
| Length | 220mm (w/o cord) | |||||
| Weight | 180g (w/o nozzle, cord) | |||||
Soldering iron 30 watt with long life tip. Kindly order in multiple of 10 ( std packing 10/box)
Piezo ignition, compact type.
Heats quickly. Takes only 30 seconds from ignition until soldering. Controls equivalent power of 15-75W with the temperature adjuster.
Optional tip converts it to a hot knife or other hot air tools.
Operates approx. 45 minutes between refills (when used at max. temperature as a soldering iron).
One-handed, one-touch ignition switch.
NOTE: Fill with gas before use.
GP-510ST:Must be used with theGP-510HT.
Temperature-Controlled 500W Super High Power Soldering Station with ST-29 stand. No tip comes along with station, please buy seprately
Print Name: Lead Free Antistatic Digital Display Microprocessor controlled Temp. Controlled Dual soldering Iron 150 and 70 watt Soldering Station ( latest technology) . No tip comes along with station, please buy seprately Brand: goot Japan Product Code: RX-822AS Waranty : 12 Months Availability: In Stock
Slide the lever in the direction of the arrow. The tip will come out. Hold and pull the plastic housing of the tip.
| Soldering Unit | ||
| Voltage/Consumption | Soldering Unit1 (RX-85GAS) : 24V AC / 72W·150W | |
| Soldering Unit2 (RX-80GAS) : 24V AC / 72W | ||
| Ground Resistance | Less than 2Ω | |
| Leak Voltage | Less than 2mV | |
| Heater | Nichrome heater | |
| Cord Length | Soldering Unit1 :1.5m, Soldering Unit2 : 1.2m | |
| Length | RX-85GAS | 174mm (with RX-85HRT-5D) |
| RX-80GAS | 158mm (with RX-80HRT-B) | |
| Weight | RX-85GAS | 39g (with RX-85HRT-5D) |
| RX-80GAS | 28g (with RX-80HRT-B) | |
Allows two-tiered setting with another RX-701AS/711AS.
| Specifications | ||
| Model | RX-701AS | RX-711AS |
| Voltage | 110V,120V,130V,220V,230V,240V AC 50/60Hz | |
| Power Consumption | 65W | |
| Power Cord Length | 1.2m | |
| Temperature Setting Range | 200–450°C | 200–480°C |
| Ripple temperature | ±5˚C (unloaded) | |
| Insulation Resistance | Over 100MΩ (500V DC) | |
| Accessories | Soldering Iron Stand (ST-27 ),Soldering Iron Tip (PX-60RT-B) | |
Quick Start (PAT.)
Reaches set temperature fast with the Quick Start circuit.
Accurate calibration.
Standard Tip / Recommended Soldering Iron Stand
| Output Voltage | 110V, 220–240V AC | |
| Dimensions | 100(W) × 57(H) × 85(D)mm | 48(W) × 31(H) × 130(D)mm |
| Weight | 266g | 75g |
Fix Temp. control Soldering Iron ( fix 420 Deg C) with PX-2RT-5C tip
Advance Tech Services Pvt. Ltd. (Advance Tech Services Pvt. Ltd.)
Advance Tech Services (P) Ltd.,
709-710, GD-ITL Towers,
B-8, Netaji Subhash Place,
Pitampura, New Delhi - 110034
India.
Share us via
