Abha Power & Steel Pvt. Ltd

Bilaspur, Chhattisgarh

Cast iron is iron or a ferrous alloy which has been heated until it liquefies, and is then poured into a mould to solidify. It is usually made from piiron. The alloy constituents affect its colour when fractured: white cast iron has carbide impurities which allow cracks to pass straight through. Grey cast iron has graphite flakes which deflect a passing crack and initiate countless new cracks as the material breaks.Cast iron is made by re-melting pig iron, often along with substantial quantities of scrap iron, scrap steel, lime stone, carbon (coke) and taking various steps to remove undesirable contaminants. Phosphorus and sulfur may be burnt out of the molten iron, but this also burns out the carbon, which must be replaced. Depending on the application, carbon and silicon content are adjusted to the desired levels, which may be anywhere from 23.5% and 13%, respectively. Other elements are then added to the melt before the final form is produced by casting.

We are one stop destinaiton for availing Spheroidal Graphite Cast Iron Rolls. These Rolls are essentially an indefinite chill type material, but with the Graphite in nodular form instead of flake and having alloyed with higher % of Nickel & Molybdenum along with carbon. So these rolls have a much higher mechanical strength and allow the use of Iron rolls in applications which would re-present too high a duty for a flake iron quality due to internal notch effect of nodular graphite is relatively small. The Spheroidal Graphite Cast Iron Rolls are very much suitable for the rolling of row products with wide range of applications due to its hardness penetration, good wear resistance and tough necks, this material has become a benchmark.

We are one stop destinaiton for availing Spheroidal Graphite Cast Iron Rolls. These Rolls are essentially an indefinite chill type material, but with the Graphite in nodular form instead of flake and having alloyed with higher % of Nickel & Molybdenum along with carbon. So these rolls have a much higher mechanical strength and allow the use of Iron rolls in applications which would re-present too high a duty for a flake iron quality due to internal notch effect of nodular graphite is relatively small. The Spheroidal Graphite Cast Iron Rolls are very much suitable for the rolling of row products with wide range of applications due to its hardness penetration, good wear resistance and tough necks, this material has become a benchmark.

We provide superlative Stainless Steel Castings that are precisely manufactured for anti-corrosive application. These precise castings are widely used in various industries likely, Pump, Valve, Chemical, Agro chemical, Petro-chemical & other industries. The basis concept of Stainless Steel castings is for Anti-corrosive, Anti-errosions, Heat resistance & are manufactured as per National as well as International Specification. The known grades are SS 304 [CF8] SS 316 [CF8M] SS 316L [CF3M] Alloy-20 [CN7M] SS 309 [CH-20] SS 310 [HK-40] etc. We are counted among the major S.S.Castings manufactured & Suppliers in India.

We provide superlative Stainless Steel Castings that are precisely manufactured for anti-corrosive application. These precise castings are widely used in various industries likely, Pump, Valve, Chemical, Agro chemical, Petro-chemical & other industries.

The basis concept of Stainless Steel castings is for Anti-corrosive, Anti-errosions, Heat resistance & are manufactured as per National as well as International Specification. The known grades are SS 304 [CF8] SS 316 [CF8M] SS 316L [CF3M] Alloy-20 [CN7M] SS 309 [CH-20] SS 310 [HK-40] etc. We are counted among the major S.S.Castings manufactured & Suppliers in India.

• Gate Valve Castings, Grizlly Bars & Screens, Flap Door (HRCS)
• Sinter Car Chain Links, Pinnions, Impellers
• Grate Bars, Front, Rear & Side Seal Plates, Roll Shells
• Crusher Hammers, Hammer Arms, Breaker Plates, Jaw Plates
• Heat Resistant Liners, High Chrome Liners, Mn Steel Liners
• Segments Single & Bi-Metallic, Roll Shell, Rotor Blades
• Bowl & Mantles, Striker Bar, Impact Bar
• SGCI Insulation Pieces, Grinding gibs, Bearing Housings
• Slag Launders, Gears, Bucket Gears, Grab Buckets, Sprockets
• Casings, Rope Drums, Star Wheel, Furnace Door Castings, Tuyers Castings

• Tooth Points, Adaptors, Dipper Teeths, Bucket Castings
• Crusher Hammers, Hammer Arms, Breaker Plates, Jaw Plates
• Grizlly Bars & Screens, Flap Door (HRCS)
• Heat Resistant Liners, High Chrome Liners, Mn Steel Liners
• Bowl & Mantles, Striker Bar, Impact Bar
• HEMM Spares, Brackets, Buckets, Lip assembly
• Front Wall, Back Wall, Crawler Show Assembly, Under Carriage Assembly
• Dipper Front, Dipper Handle, Lower Roller Assembly, Sprockets

• Grate Bars, Grate Plates, Cooler Plates & Fingers (HRCS)
• Dip Tube Segments
• Crusher Hammers, Hammer Arms, Breaker Plates, Jaw Plates
• Heat Resistant Liners, High Chrome Liners, Mn Steel Liners
• Diaphragm Liners & Back Plates, Wedges, Blow Bars
• Segments Single & Bi-Metallic, Roll Shell, Rotor Blades

Manganese steel castings includes hammers, jaw plates, grinding balls, billets etc It is used in the construction of Railway Tracks by Indian Railways. The company is accredited being one of the two only manufacturers approved by CORE Allahabad, for manufacturing 25 KV A.C. Traction overhead Electric Fittings for Indian Railways for Electrical Transmission.

We produce a large variety of ductile iron (SGCI) castings like valve bodies, spools, flanges, links, levers, water connection kits, armature fans, brackets, gear cases, axle boxes, dampers, oil seals, housings to name a few.

Manganese steel castings includes hammers, jaw plates, grinding balls, billets etc

It is used in the construction of Railway Tracks by Indian Railways. The company is accredited being one of the two only manufacturers approved by CORE Allahabad, for manufacturing 25 KV A.C. Traction overhead Electric Fittings for Indian Railways for Electrical Transmission.

Grate Bars, Grate Plates, Cooler Plates & Fingers (HRCS), Dip Tube Segments, Crusher Hammers, Hammer Arms, Breaker Plates, Jaw Plates, Diaphragm Liners & Back Plates, Wedges, Blow Bars, Segments Single & Bi-Metallic, Roll Shell, Rotor Blades.

Crusher Hammers, Hammer Arms, Breaker Plates, Jaw Plates, Grizlly Bars & Screens, Flap Door (HRCS), Heat Resistant Liners, High Chrome Liners, Mn Steel Liners, Bowl & Mantles, Striker Bar, Impact Bar, Front Wall, Back Wall, Crawler Show Assembly, Under Carriage Assembly, Dipper Front, Dipper Handle, Lower Roller Assembly, Sprockets.

Gate Valve Castings, Grizlly Bars & Screens, Flap Door (HRCS), Sinter Car Chain Links, Pinnions, Impellers, Grate Bars, Front, Rear & Side Seal Plates, Roll Shells, Crusher Hammers, Hammer Arms, Breaker Plates, Jaw Plates, SGCI Insulation Pieces, Grinding gibs, Bearing Housings, Casings, Rope Drums, Star Wheel, Furnace Door Castings, Tuyers Castings.

• Semi-Automatic Modulding M/cs Arpa 300 & Arpa 450
• Fully Automatic Shell Moulding & Mould Fuser Machines
• Separate CO2 & No-Bake Moulding System with Autobatch Mixers
• Core Shop Shell Core Shooter, Hydraulic Core Shooters, CO2 & No-Bake Cores
• Automatic Sand Plant with Knockout, Cooler, Sand Silos and Intensive Sand Mixers

All grades of Mild Steel, Sphereoidal Graphite Cast Iron, Manganese Steel, Stainless Steel, Low Alloy and High Alloy Castings(High Cr & High Ni) from as small as 0.5 Kgs to 6 Tonnes Finished Casting.