Our Products
Transformers And Transformer Parts
2 Products availableRouter, Cables & Networking Devices
1 Products availableGlassware
1 Products availableFuses, Circuit Breakers & Components
1 Products availableInsulators
1 Products availableElectric Fittings And Components
1 Products availableSwitch Gears
1 Products availableOur product range contains a wide range of epoxy resin cast components and capacitor switch
A.Bond Strands manufactures a quality range of medium voltage motor control centres and direct online starters(DOL) to control motors. Since its launch in 1990, our MCCS are rapidly gaining customer confidence and respect wherever they have been installed. Our design combines flexibility, safety and ease for maintenance inherent in our proven layouts and components. This with our engineering systems expertise enables specialised needs of most industries to be completely satisfied.
Salient Features of Motor Control Centers:
Compact, requires less floor area.
Simple and easy to install even on mobile machines.
Maximum personal safety.
Easy accessibility for maintenance.
Interchangeability of equipments of 3.3kV/6.6 kV ratings.
Custom built, to suit type of machines on which the MCC is located.
Vacuum contactor/ Air break contactor of reputed make as per customer's requirement. viz BHEL, Jyoti, etc.
A Bond - Strands Pvt. Ltd., is in the field of manufacture of various cast epoxy resin components for more than two decades. Our facility has a full component of equipment for casting under high vacuum and using pressure gellation technique to produce void free epoxy castings of high quality to suit very critical high voltage applications.
The standard items we manufacture are:
Insulators
Bushings
Seal off Bushings
Roof Bushings
Terminal Boards
Insulating Supports
Wall through FRP Bushings
In our quest for continuous improvement and expansion, we are proud to introduce a range of On Load Tap Changers to the market .
A tap changer is a connection point selection mechanism device along a power transformer winding that allows a variable number of turns to be selected in discrete steps. A transformer with a variable turns ratio is produced, enabling stepped voltage regulation of the output. The tap selection may be made via an automatic or manual tap changer mechanism.
We have the voltage rating from 11kV to 132kV. The design is of high technical standard combining dependability, reliability and marketability.
The salient features of A Bond Strands OLTC's are
High operating reliability
Easy maintenance and robust construction
Simple Drive Mechanism
Economy in design
Our externally mounted on load tap changers combine indigenous modular design with modern manufacturing methods to give a very versatile product to the market.
We have a unique design of high speed operation for coarse fine / reverser selector, which will meet all our customer's needs. This has enabled us to operate within a simple design and reduce the number of components used.
Our components are robust and not brittle in nature. Therefore no transit damage due to internal transit handling and hazardous road conditions will occur. We have only 200 components to cater to our entire range of five models.
This capacitor switch, depending on the load pattern, will close or open automatically and connect or disconnect the capacitor bank to the lines. The capacitor switch provides not only reactive power compensation at overload current, but also prevents over-voltage problem at the receiving end during light load conditions by switching "on" and "off" the capacitor bank in the circuit respectively.
Features of Capacitor Switch:
Automatic switching -on of the capacitor bank whenever the load current exceeds a re-set value. The setting of load current is adjustable upto 150 amps, continuously. An on time delay of 5 minutes is provided each time the capacitor is required to be connected. The capacitor bank is automatically disconnected if the line current is reduced below a specified level.
Automatic switching off the capacitor bank whenever the control voltage is beyond the minimum and maximum limits. i.e. 240 volts -15 % to 10%.
In the event of line current exceeding a certain specified limit, the CT mounted on Y phase operates through the control unit and closing command is given to the closing solenoid which closes the interrupter, thereby connecting the capacitor bank in the circuit and thus improving the power factor. When line current is reduced, to a specified value control, unit gives a tripping command to the trip coil thereby disconnecting the capacitor bank. The power to the closing solenoid and tripping coil is also taken from the control transformer secondary.
A Bond Strands has been a pioneer in the manufacture of glass fibre filament wound products and pipes for more than two decades. Filament winding is a precision winding method with which almost any form and dimension can be made from resin impregnated filaments of glass fibre(Originated from the rocket technology and development of the space program , this method finds entry in increasing measure in many fields of engineering and technology).
With the help of Filament-Winding -Method, we get a material which possesses the specific gravity of magnesium with the strength of steel and corrosion resistance of plastics at the same time very good electrical and dielectric properties.
A bond Strands is in the field of manufacture of unitized package substations. The unitized package substation is a state-of-the-art system which simplifies conventional substation design. Though, the concept is new in India, use of such package substations has been an accepted practice in distribution networks in Europe for several years.
Custom-Built designs such as required for constant mobility involving frequent shifting from place to place like in off-shore drilling area etc. can be offered. This offers a high flexibility of providing power supply points without much difficulty.
A high degree of safety and operational reliability are achieved by carefully selecting the associated HT & LT switchgear along with the dry type resin cast transformer provided with suitable thermistors and controllers for protecting the transformers from overloading.